Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CFD modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

CFD Based Design of a Filming Injector for N+3 Combustors

An effort was undertaken to perform CFD analysis of fluid flow in Lean-Direct Injection (LDI) combustors with axial swirl-venturi elements for next-generation LDI-3 combustor design. The National Combustion Code (NCC) was used to perform non-reacting and two-phase reacting flow computations for a newly-designed pre-filming type fuel injector LDI-3 injector, in a single-injector and a five-injector array configuration. All computations were performed with a consistent approach of mesh-optimization, spray-modeling, ignition and kinetics-modeling. Computational predictions of the aerodynamics of the single-injector were used to arrive at an optimized main-injector design that meets effective area and fuel-air mixing criteria. Emissions (EINOx) characteristics were predicted for a medium-power engine cycle condition, and will be compared with data when it is made available from experimental measurements. The use of a PDF-like turbulence-chemistry interaction model with NCC's Time-Filtered Navier-Stokes (TFNS) solver is shown to produce a significant impact on the CFD results, when compared with a laminar-chemistry TFNS approach for the five-injector computations.

combustion chambers↗
NASA NTRS1992

Preliminary efforts toward development of data handling and analysis software for unsteady flow measurements: An application for aeroelastic transonic flow configurations

A few years ago the Structural Dynamics Division at LaRC started ambitious experimental research efforts known as the Benchmark Models Program. The primary objective of this program was to provide experimental data that may serve as a calibration source for computational fluid dynamics (CFD) efforts that deal with aeroelastic unsteady flow configurations. It also focuses on the understanding of complex flow phenomenon associated with unsteady flow developments. The overall plan for the program has been described by Bennett, including a presentation of initial test results of flutter of a rigid wing mounted on flexible supports. An example of a test model employed to measure the dynamic response along with corresponding pressure distributions is shown. This model incorporates eighty pressure transducers distributed along two spanwise stations. In addition, the models are equipped with four accelerometers and two strain gages. The data handling system for the Benchmark Model Program is under development. Several interactive computer routines designed for the user interface, dynamic memory allocation, unsteady flow measurements data extraction, and further data processing were developed. To present a few examples of measured data, the unsteady pressure distributions and the wing model dynamic response were plotted.

Finaish, Fathi↗
NASA NTRS1997

Modeling of Turbulent Swirling Flows

Aircraft engine combustors generally involve turbulent swirling flows in order to enhance fuel-air mixing and flame stabilization. It has long been recognized that eddy viscosity turbulence models are unable to appropriately model swirling flows. Therefore, it has been suggested that, for the modeling of these flows, a second order closure scheme should be considered because of its ability in the modeling of rotational and curvature effects. However, this scheme will require solution of many complicated second moment transport equations (six Reynolds stresses plus other scalar fluxes and variances), which is a difficult task for any CFD implementations. Also, this scheme will require a large amount of computer resources for a general combustor swirling flow. This report is devoted to the development of a cubic Reynolds stress-strain model for turbulent swirling flows, and was inspired by the work of Launder's group at UMIST. Using this type of model, one only needs to solve two turbulence equations, one for the turbulent kinetic energy k and the other for the dissipation rate epsilon. The cubic model developed in this report is based on a general Reynolds stress-strain relationship. Two flows have been chosen for model evaluation. One is a fully developed rotating pipe flow, and the other is a more complex flow with swirl and recirculation.

Shih, Tsan-Hsing↗
NASA NTRS1993

Quantitative results from the focusing schlieren technique

An iterative theoretical approach to obtain quantitative density data from the focusing schlieren technique is proposed. The approach is based on an approximate modeling of the focusing action in a focusing schlieren system, and an estimation of an appropriate focal plane thickness. The theoretical approach is incorporated in a computer program, and results obtained from a supersonic wind tunnel experiment evaluated by comparison with CFD data. The density distributions compared favorably with CFD predictions. However, improvements to the system are required in order to reduce noise in the data, to improve specifications of a depth of focus, and to refine the modeling of the focusing action.

Cook, S. P.↗
NASA NTRS1992

On some recent advances in multidisciplinary analysis of hypersonic vehicles

This paper presents pertinent details of the development and application of an integrated, multidisciplinary finite element analysis tool for the effective modeling and simulation of aerospace vehicles including hypersonic ones. Recent advances in this connection include more efficient CFD solution techniques and also aeroservoelastic stability analysis methods that employ unsteady aerodynamic forces for computation of flutter and divergence speeds. An accelerated Euler solution procedure based on the Aitken acceleration technique has recently been implemented that effects considerable improvement in solution efficiency for the same level of solution accuracy, as evidenced by example problems presented in the paper. A summary of finite element numerical formulations for the various individual disciplines as well as for the unified aeroservoelastic analysis and some relevant numerical examples are also presented in the paper.

Gupta, K. K.↗
NASA NTRS1993

Transonic wind tunnel wall interference analysis for the Space Shuttle Launch Vehicle

The AEDC perforated-wall boundary condition has been incorporated into the NASA Ames OVERFLOW code and has been used to calculate the tunnel flow field in the AEDC Aerodynamic Wind Tunnel (16T) over a three-percent model of the Space Shuttle Launch Vehicle. Tunnel flow-field calculations have been performed for two supersonic flow-field conditions, including one near sonic condition. Wall interference assessments and analyses have been performed by making detailed comparisons of the tunnel flow-field calculations with corresponding free-air flow-field calculations and with tunnel data from different scale models. A capability to assess wall interference at low supersonic conditions and to improve data correlations with CFD results by adding the tunnel wall boundary condition is demonstrated.

Martin, F. W., Jr.↗
NASA NTRS1993

Looking for O(N) Navier-Stokes solutions on non-structured meshes

Multigrid methods are good candidates for the resolution of the system arising in numerical fluid dynamics. However, the question is to know if those algorithms which are efficient for the Poisson equation on structured meshes will still apply well to the Euler and Navier-Stokes equations on unstructured meshes. The study of elliptic problems leads us to define the conditions where a full multigrid strategy has O(N) complexity. The aim of this paper is to build a comparison between the elliptic theory and practical CFD problems. First, as an introduction, we will recall some basic definitions and theorems applied to a model problem. The goal of this section is to point out the different properties that we need to produce an FMG algorithm with O(N) complexity. Then, we will show how we can apply this theory to the fluid dynamics equations such as Euler and Navier-Stokes equations. At last, we present some results which are 2nd-order accurate and some explanations about the behavior of the FMG process.

Morano, Eric↗
NASA NTRS1993

Looking for O(N) Navier-Stokes solutions on non-structured meshes

Multigrid methods are good candidates for the resolution of the system arising in Numerical Fluid Dynamics. However, the question is to know if those algorithms which are efficient for the Poissan equation on structured meshes will still apply well to the Euler and Navier-Stokes equations on unstructured meshes. The study of elliptic problems leads us to define the conditions where a Full Multigrid strategy has O(N) complexity. The aim of this paper is to build a comparison between the elliptic theory and practical CFD problems. First, as an introduction, we will recall some basic definitions and theorems applied to a model problem. The goal of this section is to point out the different properties that we need to produce an FMG algorithm with O(N) complexity. Then, we will show how we can apply this theory to the fluid dynamics equations such as Euler and Navier-Stokes equations. At last, we present some results which are 2nd-order accurate and some explanations about the behavior of the FMG process.

Morano, Eric↗
NASA NTRS2010

Aeroelastic Computations of a Compressor Stage Using the Harmonic Balance Method

The aeroelastic characteristics of a compressor stage were analyzed using a computational fluid dynamic (CFD) solver that uses the harmonic balance method to solve the governing equations. The three dimensional solver models the unsteady flow field due to blade vibration using the Reynolds-Averaged Navier-Stokes equations. The formulation enables the study of the effect of blade row interaction through the inclusion of coupling modes between blade rows. It also enables the study of nonlinear effects of high amplitude blade vibration by the inclusion of higher harmonics of the fundamental blade vibration frequency. In the present work, the solver is applied to study in detail the aeroelastic characteristics of a transonic compressor stage. Various parameters were included in the study: number of coupling modes, blade row axial spacing, and operating speeds. Only the first vibration mode is considered with amplitude of oscillation in the linear range. Both aeroelastic stability (flutter) of rotor blade and unsteady loading on the stator are calculated. The study showed that for the stage considered, the rotor aerodynamic damping is not influenced by the presence of the stator even when the axial spacing is reduced by nearly 25 percent. However, the study showed that blade row interaction effects become important for the unsteady loading on the stator when the axial spacing is reduced by the same amount.

Reddy, T. S. R.↗
NASA NTRS2011

Aerodynamic Analyses and Database Development for Ares I Vehicle First Stage Separation

This paper presents the aerodynamic analysis and database development for first stage separation of Ares I A106 crew launch vehicle configuration. Separate 6-DOF databases were created for the first stage and upper stage and each database consists of three components: (a) isolated or freestream coefficients, (b) power-off proximity increments, and (c) power-on proximity increments. The isolated and power-off incremental databases were developed using data from 1% scaled model tests in AEDC VKF Tunnel A. The power-on proximity increments were developed using OVERFLOW CFD solutions. The database also includes incremental coefficients for one BDM and one USM failure scenarios.

Pamadi, Bandu N.↗
NASA NTRS2011

Aerothermodynamics of Blunt Body Entry Vehicles

In this chapter, the aerothermodynamic phenomena of blunt body entry vehicles are discussed. Four topics will be considered that present challenges to current computational modeling techniques for blunt body environments: turbulent flow, non-equilibrium flow, rarefied flow, and radiation transport. Examples of comparisons between computational tools to ground and flight-test data will be presented in order to illustrate the challenges existing in the numerical modeling of each of these phenomena and to provide test cases for evaluation of Computational Fluid Dynamics (CFD) code predictions.

Hollis, Brian R.↗
NASA NTRS2010

Direct Measurement Sensor of the Boundary Shear Stress in Fluid Flow

The flow fields and boundary erosion that are associated with scour at bridge piers are very complex. Direct measurement of the boundary shear stress and boundary pressure fluctuations in experimental scour research has always been a challenge and high spatial resolution and fidelity have been almost impossible. Most researchers have applied an indirect process to determine shear stress using precise measured velocity profiles. Laser Doppler Anemometry and Particle Image Velocimetry are common techniques used to accurately measure velocity profiles. These methods are based on theoretical assumptions to estimate boundary shear stress. In addition, available turbulence models cannot very well account for the effect of bed roughness which is fundamentally important for any CFD simulation. The authors have taken on the challenge to advance the magnitude level to which direct measurements of the shear stress in water flow can be performed. This paper covered the challenges and the efforts to develop a higher accuracy and small spatial resolution sensor. Also, preliminary sensor designs and test results are presented.

Badescu, Mircea↗
NASA NTRS2016

Computational Study of Flow Interactions in Coaxial Rotors

Although the first idea of coaxial rotors appeared more than 150 years ago, most helicopters have used single main-rotor/tail-rotor combination. Since reactive moments of coaxial rotors are canceled by contra-rotation, no tail rotor is required to counter the torque generated by the main rotor. Unlike the single main rotor design that distributes power to both main and tail rotors, all of the power for coaxial rotors is used for vertical thrust. Thus, no power is wasted for anti-torque or directional control. The saved power helps coaxial rotors reach a higher hover ceiling than single rotor helicopters. Another advantage of coaxial rotors is that the overall rotor diameter can be reduced for a given vehicle gross weight because each rotor provides a maximum contribution to vertical thrust to overcome vehicle weight. However, increased mechanical complexity of the hub has been one of the challenges for manufacturing coaxial rotorcraft. Only the Kamov Design Bureau of Russia had been notably successful in production of coaxial helicopters until Sikorsky built X2, an experimental compound helicopter. Recent developments in unmanned aircraft systems and high-speed rotorcraft have renewed interest in the coaxial configuration. Multi-rotors are frequently used for small electric unmanned rotorcraft partly due to mechanical simplicity. The use of multiple motors provides redundancy as well as cost-efficiency. The multi-rotor concept has rarely been used until recently because of its inherent stability and control problems. However, advances in inexpensive electronic flight control systems have opened the floodgates for small drones using multirotors. Coaxial rotors have started to appear in some multi-rotor configurations. Small coaxial rotors have often been designed using a hundred year old approach that is "sketch, build, fly, and iterate." In that approach, there is no systematic way to explore trade-offs or determine logical next steps. It is neither possible to account for multiple real-world constraints up front in design nor possible to know what performance is possible with a given design. Since unmanned vehicles are sized and optimized for the particular mission, a modern low-fidelity conceptual design and sizing tool that has been used for the design of large helicopters can be used for design of small coaxial rotorcraft. However, unlike most helicopters with single main rotor, the interactions between the upper and lower rotors emerge as an important factor to consider in design because an increase in performance of a multi-rotor system is not proportional to the number of rotors. Interference losses and differences in thrusts between the upper and lower rotors were investigated by theoretical methods as well as a computational fluid dynamics (CFD) method using the Reynolds-Averaged Navier-Stokes (RANS) equations. In this work, hybrid turbulence models are used to investigate the physics of interactions between coaxial rotors and a fuselage that are not well understood. Present study covers not only small-scale drones but also large-scale coaxial rotors for heavy-lifting missions. Considering the recently proposed FAA drone rules that require the flight only in visual line-of-sight, a large multirotor might be used as an airborne carrier for launch and recovery of unmanned aircraft systems with a human operator onboard. For applications to civil operations, their aerodynamic performance and noise levels need to be assessed. Noise is one of the largest limiting factors to rotorcraft operations in urban area. Since the high-frequency noise of multi-rotors may increase the annoyance, noise may turn out to be a key issue that must be addressed for market acceptability. One of the objectives of the present work is to study the effects of inter-rotor spacing and collectives on the performance, efficiency, and acoustics of coaxial rotor systems.

Study↗
NASA NTRS2014

The D8 Aircraft: An Aerodynamics Study of Boundary Layer and Wake Ingestion Benefit

Goal: Quantify benefits of BLI (Boundary Layer Ingesting) and wake ingestion for the D8. Approach: Overset CFD (Computational Fluid Dynamics) using CGT (Chimera Grid Tools software package) and Overflow-­‐2; CFD validation; NASA LaRC (Langley Research Center) 14x22 WT (wind tunnel) data for a 1:11 scale model; Quantifying the BLI and wake ingestion benefit - Direct Comparison between: Efficient conventional (podded nacelle) configuration; BLI (integrated nacelle) configuration.

D8↗
NASA NTRSDate not supplied

OVERFLOW Analysis of Supersonic Retropropulsion Testingon the CobraMRV Mars Entry Vehicle Concept

The CFD solver OVERFLOW was used to simulate the CobraMRV undergoing supersonic retropropulsion (SRP) in the Langley Unitary Plan Wind Tunnel as part of a pre-test study. Aerodynamics of the CobraMRV are summarized and the sensitivity of vehicle loads to CFD parameters at a subset of operating conditions are investigated. Specific numerical methods, boundary conditions, and turbulence modeling options have been selected after considering the complex phenomena in SRP flows. Proper shock-capturing methods and dynamic grid adaption are necessary to correctly capture vehicle loads and dynamics. Present data indicates that at particular conditions, upstream asymmetries originating from the tunnel inflow plane contribute to measurable asymmetries on the CobraMRV heatshield.

OVERFLOW↗
NASA NTRSDate not supplied

High-Fidelity Aerodynamic Analysis and Optimization of the SUSAN Electrofan Concept

The Subsonic Single Aft Engine (SUSAN) Electrofan is a new single-aisle regional jet class transport aircraft being studied by NASA, which benefits from reduced fuel consumption through a reduction in the number of hydrocarbon fuel-burning engines from two to one. This is achieved through a hybrid-electric system architecture, where a series of generators are used to extract power from a fuel-consuming tail cone thruster to drive electric propulsors mounted on the wings. To support the development of these propulsion systems, which involve high levels of propulsion-airframe integration, this paper presents high-fidelity analyses through computational fluid dynamics (CFD) simulations provided by the Launch Ascent and Vehicle Aerodynamics (LAVA) framework, which also includes capabilities for modeling the effect of active propulsors. A trade space exploration is performed to investigate the advantages of several wing mounted distributed electric propulsion system configurations, including over-wing, under-wing, and trailing-edge arrangements. For the aft fuselage propulsor, focus is on the sizing of the inlet, core, and bypass ducts. High-fidelity aerodynamic shape optimization is also used to help minimize the inlet distortion intensity experienced by the aft propulsor fan through a reshaping of the fuselage.

CAS↗
NASA NTRS2022

Framework for Estimating Performance and Associated Uncertainty for Modified Aircraft Configurations

Flight testing has been the historical standard for determining aircraft airworthiness. However, increases in the cost of flight testing and the accuracy of inexpensive CFD encourage the adoption of certification by analysis to reduce or replace flight testing. A framework is introduced to predict the performance in the special case of a modification to an existing, previously certified aircraft. This framework uses a combination of existing flight tests or high fidelity data of the original aircraft as well as lower fidelity data from CFD or wind tunnel testing of the original and modified configurations to create 6-DOF flight dynamics models. Two methods are presented which generate an updated flight dynamics model and estimate the model form uncertainty for the modified aircraft configuration using knowledge of the original aircraft. This updated dynamics model and uncertainty estimate are then used to conduct non-deterministic simulations with wind turbulence included. The framework is applied to an example aircraft system to demonstrate the ability to predict the performance and associated model from the uncertainty of modified aircraft configurations.

uncertainty quantification↗
NASA NTRSDate not supplied

LOFTID Surface Heating Reconstruction

On November 10, 2022, the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) reentry vehicle launched to low-Earth orbit aboard a United Launch Alliance Atlas V rocket out of Vandenberg Air Force Base. The aeroshell, the largest Hypersonic Inflatable Aerodynamic Decelerator (HIAD) ever flown, was inflated to its full 6-meter diameter before successful re-entry into the atmosphere. The aeroshell was heavily instrumented in order to understand its behavior during entry. There were 82 thermocouples (TCs) distributed across the aeroshell, with 22 integrated into the flexible thermal protection system (FTPS) on the rigid nose, 36 in the FTPS on the deployable structure, and 24 on the inflatable structure. TCs were placed at different depths throughout the FTPS. Those nearest to the surface were located just beneath the two SiC outer fabric layers. The near-surface TCs on the rigid nose were Type R with flame spray alumina insulation, while those on the flank were Type N with mica/ceramic insulation. Additionally, a radiometer was placed at the center of the nose surrounded by four total heat flux gauges in a cruciform configuration at a radius of 0.41 m. The nose instrumentation is shown in Fig. 1 and a cross-section of the aeroshell with all TC locations is shown in Fig. 2. The objective of this work was to use the temperatures measured by the TCs during flight to estimate the surface heat rate across the aeroshell throughout the period of re-entry by inverse analysis methodology. The results were used to evaluate the fidelity of measurements from the total heat flux gauges on the nose, determine the surface heat flux at aeroshell locations where gauges were not present, and compare to pre-flight CFD-based heating predictions. Inversely estimated surface heat flux continues to be used to correlate FTPS thermal models to reconstruct in-flight thermal response.

H S Alpert↗