Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ALTERNATIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Alternative approximation concepts for space frame synthesis

A structural synthesis methodology for the minimum mass design of 3-dimensionall frame-truss structures under multiple static loading conditions and subject to limits on displacements, rotations, stresses, local buckling, and element cross-sectional dimensions is presented. A variety of approximation concept options are employed to yield near optimum designs after no more than 10 structural analyses. Available options include: (A) formulation of the nonlinear mathematcal programming problem in either reciprocal section property (RSP) or cross-sectional dimension (CSD) space; (B) two alternative approximate problem structures in each design space; and (C) three distinct assumptions about element end-force variations. Fixed element, design element linking, and temporary constraint deletion features are also included. The solution of each approximate problem, in either its primal or dual form, is obtained using CONMIN, a feasible directions program. The frame-truss synthesis methodology is implemented in the COMPASS computer program and is used to solve a variety of problems. These problems were chosen so that, in addition to exercising the various approximation concepts options, the results could be compared with previously published work.

Lust, R. V.↗

The use of hydrazine as an alternate source of energy

The potentials of using hydrazine as an alternative source of energy was studied. Three chemical reactions are considered: oxidation with air, oxidation with hydrogen peroxide, and thermocatalytic decomposition. Performance data of gasoline, ethylic alcohol, and propane are compared. An item about the NO(x) emissions by the various investigated reactions is included. Promising results are shown, mainly those regarding the available energy per unit volume of unburned gases (vaporized fuel and oxidizer).

Carvalho, J. A., Jr.↗

Alternatives for jet engine control

The technical progress of researches Alternatives for Jet Engine Control is reported. A numerical study employing feedback tensors for optimal control of nonlinear systems was completed. It is believed that these studies are the first of their kind. State regulation, with a decrease in control power is demonstrated. A detailed treatment follows.

Sain, M. K.↗

Alternatives for jet engine control

The technical progress of researches on alternatives for jet engine control, is reported. The principal new activities involved the initial testing of an input design method for choosing the inputs to a non-linear system to aid the approximation of its tensor parameters, and the beginning of order reduction studies designed to remove unnecessary monomials from tensor models.

Sain, M. K.↗

Alternatives for jet engine control

The technical progress of researches on alternatives for jet engine control is reported. Extensive numerical testing is included. It is indicated that optimal inputs contribute significantly to the process of calculating tensor approximations for nonlinear systems, and that the resulting approximations may be order-reduced in a systematic way.

Sain, M. K.↗

Alternatives for Jet Engine Control. Volume 1: Modelling and Control Design with Jet Engine Data

This document compiles a comprehensive list of publications supported by, or related to, National Aeronautics and Space Administration Grant NSG-3048, entitled "Alternatives for Jet Engine Control". Dr. Kurt Seldner was the original Technical Officer for the grant, at Lewis Research Center. Dr. Bruce Lehtinen was the final Technical Officer. At the University of Notre Dame, Drs. Michael K. Sain and R. Jeffrey Leake were the original Project Directors, with Dr. Sain becoming the final Project Director. Publications cover work over a ten-year period. The Final Report is divided into two parts. Volume i, "Modelling and Control Design with Jet Engine Data", follows in this report. Volume 2, "Modelling and Control Design with Tensors", has been bound separately.

Sain, M. K.↗

The Alternating Surface Segmented Lap Joint: a Design for Thin Highly Loaded Joints

The combination of thin airfoil sections and high aerodynamic loads on many wind tunnel models presents a major problem for attachment of flap elements. Conventional methods of attaching fixed control elements such as lap and tongue-in-groove joints are not rigid enough to provide surface continuity required in high Reynolds number research. For the extreme cases, the solution has been to fabricate separate wings for each flap setting with the flap element being and integral part of the wing. Here an attractive solution to this problem, the alternating surface segmented lap joint, is discussed. This joint provides increased rigidity and lower stress levels than conventional joints. Additionally, attachment fastener loading is low and the joint can be designed to accommodate high shear levels due to bending without the use of dowel pins.

Watkins, V. E., Jr.↗

The B2 aluminides as alternative materials

The potential of the B2 aluminides as structural material alternatives for the strategic element containing superalloys currently used in gas turbine engines is being explored with emphasis on the equiatomic Fe and Ni aluminides. Although Co is a strategic material, the equiatomic Co aluminide is also being studied to gain a more complete understanding of these fourth period intermetallics. Research focuses on initial processing techniques such as ingot melting, power metallurgy, and rapid solidification with and without additional thermomechanical processing; high temperature deformation primarily compressive creep; compositional effects within the binary B2 aluminides; third-element alloying addition effects on high temperature strength and oxidation resistance, and near room temperature ductility as influenced by processing, alloying, and grain size. Various programs now underway are reviewed and some highlights of research results are presented.

Stephens, J. R.↗

An alternative multi-mode SAR for RADARSAT

The RADARSAT project was asked by the Canadian government in the spring of 1986 to design for reduced costs and increased radar performance as compared to the well-known baseline design. Both the Project Office and Canadian industry (lead by SPAR Aerospace of Montreal) have undertaken to meet this request, with a proposal to cabinet to be submitted in the fall of 1986. One alternative SAR concept is outlined which is under consideration for a revised RADARSAT configuration. The radar system described uses two frequencies (C&L band) over four possible modes: near range swath; far range swath; wide swath; and high resolution. Good sensitivity, resolution, and coverage are obtained with modest power and data rates. The antenna systems are relatively simple. Indeed, no break-through technological developments are needed. The design allows several mode combinations for simultaneous data collection or performance enhancement. The principal parameters are described. A nominal mean altitude of 700 km is assumed.

Raney, R. K.↗

The ballistic Mars hopper - An alternative Mars mobility concept

The ballistic Mars hopper is proposed as an alternative mobility concept for unmanned exploration of the Martian surface. In the concept, oxygen and carbon monoxide produced from the Martian atmosphere are used as propellants in a rocket propulsion system for an unmanned vehicle on suborbital trajectories between landing sites separated by distances of up to 1000 km. This mobility concept is seen as uniquely capable of allowing both intensive and extensive exploration of the planet using only a single landed vehicle of mass approximately 2000 kg. The technical challenges associated with in-situ propellant production on the surface of Mars are reviewed. A rocket propulsion subsystem capable of using oxygen and carbon monoxide as propellants is described. Finally, results of mission analysis and a hopper landing hazard simulation are reported. It is concluded that an attractive Mars hopper can be developed based on relatively near-term technology.

Sercel, Joel C.↗

Aircraft interior noise reduction by alternate resonance tuning

Model problem development and analysis continues with the Alternate Resonance Tuning concept. Various topics are presently at different stages of completion and are described. These topics included optimization of panel mass ratios, panel computer code verification and agreement with experimental data, and flexible frame modeling.

Gottwald, James A.↗

Surrogate measures: A proposed alternative in human factors assessment of operational measures of performance

Surrogate measures are proposed as an alternative to direct assessment of operational performance for purposes of screening agents who may have to work under unusual stresses or in exotic environments. Such measures are particularly proposed when the surrogate can be empirically validated against the operational criterion. The focus is on cognitive (or throughput) performances in humans as opposed to sensory (input) or motor (output) measures, but the methods should be applicable for development of batteries which will tap input/output functions. A menu of performance tasks is under development for implementation on a battery-operated portable microcomputer, with 21 tests currently available. The tasks are reliable and become stable in minimum amounts of time; appear sensitive to some agents; comprise constructs related to actual job tasks; and are easily administered in most environments. Implications for human factors engineering studies in environmental stress are discussed.

Kennedy, Robert S.↗

Computer-aided modeling and prediction of performance of the modified Lundell class of alternators in space station solar dynamic power systems

The main purpose of this project is the development of computer-aided models for purposes of studying the effects of various design changes on the parameters and performance characteristics of the modified Lundell class of alternators (MLA) as components of a solar dynamic power system supplying electric energy needs in the forthcoming space station. Key to this modeling effort is the computation of magnetic field distribution in MLAs. Since the nature of the magnetic field is three-dimensional, the first step in the investigation was to apply the finite element method to discretize volume, using the tetrahedron as the basic 3-D element. Details of the stator 3-D finite element grid are given. A preliminary look at the early stage of a 3-D rotor grid is presented.

Demerdash, Nabeel A. O.↗

A finite-element alternating method for two-dimensional Mode-1 crack configurations

A finite-element alternating method is presented for 2-D Mode-1 crack problems. An analytical solution for an arbitrary polynomial normal pressure distribution applied to the crack faces is obtained and used as the basic solution in the method. The method is applied to several crack problems to study its efficiency and the results are compared to accurate stress-intensity factor solutions in the literature. The method gave reasonably accurate stress-intensity factors and crack opening displacements with minimal computing effort. Because the method must model only the uncracked body, finite-element models with many degrees of freedom are not warranted and therefore, the method has been implemented on personal computers.

Raju, I. S.↗

Aircraft interior noise reduction by alternate resonance tuning

Model problem development and analysis continues with the Alternate Resonance Tuning (ART) concept. The various topics described are presently at different stages of completion: investigation of the effectiveness of the ART concept under an external propagating pressure field associated with propeller passage by the fuselage; analysis of ART performance with a double panel wall mounted in a flexible frame model; development of a data fitting scheme using a branch analysis with a Newton-Raphson scheme in multiple dimensions to determine values of critical parameters in the actual experimental apparatus; and investigation of the ART effect with real panels as opposed to the spring-mass-damper systems currently used in much of the theory.

Bliss, Donald B.↗

Flight simulator requirements for airline transport pilot training - An evaluation of motion system design alternatives

The effect of motion platform systems on pilot behavior is considered with emphasis placed on civil aviation applications. A dynamic model for human spatial orientation based on the physiological structure and function of the human vestibular system is presented. Motion platform alternatives were evaluated on the basis of the following motion platform conditions: motion with six degrees-of-freedom required for Phase II simulators and two limited motion conditions. Consideration was given to engine flameout, airwork, and approach and landing scenarios.

Lee, A. T.↗

Aeroelastic effects of alternate blade sweep on advanced propfan rotor

Recent progress in the development of a general purpose unsteady aerodynamic and aeroelastic analysis capability for Advanced Turboprops will be reviewed. An application to a rotor with alternating forward and backward swept blades is described, which illustrates the general 'mistuning' capability of the method.

Williams, Marc H.↗