Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wake fields”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Turbulence Modeling Validation, Testing, and Development

The primary objective of this work is to provide accurate numerical solutions for selected flow fields and to compare and evaluate the performance of selected turbulence models with experimental results. Four popular turbulence models have been tested and validated against experimental data often turbulent flows. The models are: (1) the two-equation k-epsilon model of Wilcox, (2) the two-equation k-epsilon model of Launder and Sharma, (3) the two-equation k-omega/k-epsilon SST model of Menter, and (4) the one-equation model of Spalart and Allmaras. The flows investigated are five free shear flows consisting of a mixing layer, a round jet, a plane jet, a plane wake, and a compressible mixing layer; and five boundary layer flows consisting of an incompressible flat plate, a Mach 5 adiabatic flat plate, a separated boundary layer, an axisymmetric shock-wave/boundary layer interaction, and an RAE 2822 transonic airfoil. The experimental data for these flows are well established and have been extensively used in model developments. The results are shown in the following four sections: Part A describes the equations of motion and boundary conditions; Part B describes the model equations, constants, parameters, boundary conditions, and numerical implementation; and Parts C and D describe the experimental data and the performance of the models in the free-shear flows and the boundary layer flows, respectively.

Bardina, J. E.↗

Tracing ram-pressure stripping with warm molecular hydrogen emission

We use the Spitzer Infrared Spectrograph to study four infalling cluster galaxies with signatures of ongoing ram-pressure stripping. H{sub 2} emission is detected in all four, and two show extraplanar H{sub 2} emission. The emission usually has a warm (T ∼ 115-160 K) and a hot (T ∼ 400-600 K) component that is approximately two orders of magnitude less massive than the warm one. The warm component column densities are typically 10{sup 19} to 10{sup 20} cm{sup –2} with masses of 10{sup 6} to 10{sup 8} M {sub ☉}. The warm H{sub 2} is anomalously bright compared with normal star-forming galaxies and therefore may be excited by ram-pressure. In the case of CGCG 97-073, the H{sub 2} is offset from the majority of star formation along the direction of the galaxy's motion in the cluster, suggesting that it is forming in the ram-pressure wake of the galaxy. Another galaxy, NGC 4522, exhibits a warm H{sub 2} tail approximately 4 kpc in length. These results support the hypothesis that H{sub 2} within these galaxies is shock-heated from the interaction with the intracluster medium. Stripping of dust is also a common feature of the galaxies. For NGC 4522, where the distribution of dust at 8 μm is well resolved, knots and ripples demonstrate the turbulent nature of the stripping process. The Hα and 24 μm luminosities show that most of the galaxies have star-formation rates comparable to similar mass counterparts in the field. Finally, we suggest a possible evolutionary sequence primarily related to the strength of ram-pressure that a galaxy experiences to explain the varied results observed in our sample.

79 ASTRONOMY AND ASTROPHYSICS↗

Aerodynamic and acoustic tests of duct-burning turbofan exhaust nozzles

The static aerodynamic and acoustic characteristics of duct-burning turbofan (DBTF) exhaust nozzles are established. Scale models, having a total area equivalent to a 0.127 m diameter convergent nozzle, simulating unsuppressed coannular nozzles and mechanically suppressed nozzles with and without ejectors (hardwall and acoustically treated) were tested in a quiescent environment. The ratio of fan to primary area was varied from 0.75 to 1.2. Far field acoustic data, perceived noise levels, and thrust measurements were obtained for 417 test conditions. Pressure ratios were varied from 1.3 to 4.1 in the fan stream and from 1.53 to 2.5 in the primary stream. Total temperature varied from 395 to 1090 K in both streams. Jet noise reductions relative to synthesized prediction from 8 PNdB (with the unsuppressed coannular nozzle) to 15 PNdB (with a mechanically suppressed configuration) were observed at conditions typical of engines being considered under the Advanced Supersonic Technology program. The inherent suppression characteristic of the unsuppressed coannular nozzle is related to the rapid mixing in the jet wake caused by the velocity profiles associated with the DBTF. Since this can be achieved without a mechanical suppressor, significant reductions in aircraft weight or noise footprint can be realized.

Kozlowski, H.↗

Airborne Observation of the Hayabusa Sample Return Capsule Re-Entry

The Japan Aerospace Exploration Agency (JAXA) recently completed their Hayabusa asteroid exploration mission. Launched in 2003, Hayabusa made contact with, and retrieved a sample from, the near-Earth asteroid Itokawa in 2005. The sample return capsule (SRC) re-entered over the Woomera Test Range (WTR) in southern Australia on June 13, 2010, at approximately 11:21 pm local time (09:51 UTC). The SRC re-entry velocity was 12.2 km/s, making it the second-fastest Earth return velocity behind NASA s Stardust sample return capsule re-entry in 2006. From a space technology development perspective, Hayabusa s re-entry functioned as a rare flight experiment of an entry vehicle and its thermal protection system. In collaboration with the SETI Institute, NASA deployed its DC-8 airborne laboratory and a team of international researchers to Australia to observe the re-entry of the SRC. The use of an airborne platform enables observation above most clouds and weather and greatly diminishes atmospheric absorption of the optical signals. The DC-8 s flight path was engineered and flown to provide a view of the spacecraft that bracketed the heat pulse to the capsule. A suite of imaging instruments on board the DC-8 successfully recorded the luminous portion of the re-entry event. For approximately 70 seconds, the spectroscopic and radiometric instruments acquired images and spectra of the capsule, its wake, and destructive re-entry of the spacecraft bus. Figure 1 shows a perspective view of the WTR, the SRC re-entry trajectory, and the flight path of the DC-8. The SRC was jettisoned from the spacecraft bus approximately 3 hours prior to entry interface. Due to thruster failures on the spacecraft, it could not be diverted from the entry path and followed the trajectory of the SRC, where it burned up in the atmosphere between approximately 100 and 50 km altitude. Fortuitously, the separation distance between the spacecraft and SRC was sufficient to clearly resolve the SRC from the debris field of the burning spacecraft. Figure 2 shows a frame from a high-definition television camera on board the aircraft and denotes the locations of the SRC and spacecraft bus debris.

Grinstead, Jay H.↗

Influence of asymmetric injection of laser radiation into capillary waveguides on wake acceleration of electrons possessing various injection energies

Laser wakefield acceleration of electron bunches possessing various initial injection energies in capillary waveguides is studied in the conditions of an asymmetric input of laser radiation into a waveguide (the propagation direction of laser radiation deviates from the capillary axis or the laser spot is not symmetric). The factors determining the critical angle of the laser radiation input into the capillary, within which the wake acceleration of electrons is close to optimal, have been found. It is shown that in acceleration stages where electron energies are high, the requirements to angular concentricity of the capillary axis and laser radiation focusing are substantially weaker due to the relativistic 'weighting' of the electron mass. (extreme laser radiation: physics and fundamental applications)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Theoretical investigations of high lift aerodynamics

A program which generates a coordinate system for a two element airfoil with the mesh points concentrated in areas of significant vorticity, i.e., boundary layer and wake is operational. The 'imbedded' grid method developed allows a transition from the scale of the main airfoil to the scale of the flap. This requirement is essential for the modeling of viscous flows over the flap and slat of a multielement airfoil. An airfoil mounted in a 2-D wind tunnel was formulated. The program is ready for a fine grid and a large number of planes to explore the characteristics of a Navier-Stokes solver in a quasi-3D case. The program was converted to a form suitable for the STAR computer. Runs were made to map a three dimensional flow field for a wall airfoil intersection with and without lift.

Bennett, G.↗

Acoustic Characteristics of a Model Isolated Tiltrotor in DNW

An aeroacoustic wind tunnel test was conducted using a scaled isolated tiltrotor model. Acoustic data were acquired using an in-flow microphone wing traversed beneath the model to map the directivity of the near-field acoustic radiation of the rotor for a parametric variation of rotor angle-of-attack, tunnel speed, and rotor thrust. Acoustic metric data were examined to show trends of impulsive noise for the parametric variations. BVISPL maximum noise levels were found to increase with alpha for constant mu and C(sub T), although the maximum BVI levels were found at much higher a than for a typical helicopter. BVISPL levels were found to increase with mu for constant alpha and C(sub T. BVISPL was found to decrease with increasing CT for constant a and m, although BVISPL increased with thrust for a constant wake geometry. Metric data were also scaled for M(sub up) to evaluate how well simple power law scaling could be used to correct metric data for M(sub up) effects.

Booth, Earl R., Jr.↗

Study of the Unsteady Flow Features on a Stalled Wing

The occurrence of large scale structures in the post stall flow over a rectangular wing at high angles of attack was investigated in a small-scale subsonic wind tunnel. Mean and time dependent measurements within the separated flow field suggest the existence of two distinct angle of attack regimes beyond wing stall. The shallow stall regime occurs over a narrow range of incidence angles (2-3 deg.) immediately following the inception of leading edge separation. In this regime, the principal mean flow structures, termed stall cells, are manifested as a distinct spanwise periodicity in the chordwise extent of the separated region on the model surface with possible lateral mobility not previously reported. Within the stall cells and on the wing surface, large amplitude pressure fluctuations occur with a frequency much lower than anticipated for bluff body shedding, and with minimum effect in the far wake. In the deep stall regime, stall cells are not observed and the separated region near the model is relatively free of large amplitude pressure disturbances.

Yon, Steven A.↗

Automated Fluid Feature Extraction from Transient Simulations

In the past, feature extraction and identification were interesting concepts, but not required to understand the underlying physics of a steady flow field. This is because the results of the more traditional tools like iso-surfaces, cuts and streamlines were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of much interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one 'snap-shot' of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for co-processing environments like pV3). And methods must be developed to abstract the feature and display it in a manner that physically makes sense. The following is a list of the important physical phenomena found in transient (and steady-state) fluid flow: Shocks; Vortex ores; Regions of Recirculation; Boundary Layers; Wakes.

Haimes, Robert↗

Acoustic Characteristics of a Model Isolated Tiltrotor in DNW

An aeroacoustic wind tunnel test was conducted using a scaled isolated tiltrotor model. Acoustic data were acquired using an in-flow microphone wing traversed beneath the model to map the directivity of the near-field acoustic radiation of the rotor for a parametric variation of rotor angle-of-attack, tunnel speed, and rotor thrust. Acoustic metric data were examined to show trends of impulsive noise for the parametric variations. BVISPL maximum noise levels were found to increase with mu for constant alpha and C(sub T), although the maximum BVI levels were found at much higher cc than for a typical helicopter. BVISPL levels were found to increase with mu for constant alpha and C(sub T). BVISPL was found to decrease with increasing C(sub T) for constant alpha and mu, although BVISPL increased with thrust for a constant wake geometry. Metric data were also scaled for M,i, to evaluate how well simple power law scaling could be used to correct metric data for M(sub tip) effects.

Booth, Earl R., Jr.↗

Experimental investigation of the flowfield of an oscillating airfoil

The flow field of an airfoil oscillated periodically over a wide range of reduced frequencies, 0 less than k less than 1.6, is studied experimentally at chord Reynolds numbers of R sub c = 22,000 and 44,000. The NACA0012 airfoil is pitched sinusoidally about one quarter chord between alpha of 5 deg and 25 deg. Detailed flow visualization and phase averaged vorticity measurements are carried out for k = 0.2 to document the evolution and the shedding of the dynamic stall vortex (DSV). In addition to the DSV, an intense vortex of opposite sign originates from the trailing edge just when the DSV is shed. After being shed into the wake, the two together take the shape of a large 'mushroom' while being convected away from the airfoil. The unsteady circulation around the airfoil and, therefore, the time varying component of the lift is estimated in a novel way from the shed vorticity flux and is found to be in good agreement with the lift variation reported by others. The delay in the shedding of the DSV with increasing k, as observed by previous researchers, is documented for the full range of k. The DSV, for example, is shed nearly at the maximum alpha of 25 deg at k = 0.2, but is shed at the minimum alpha of 5 deg at k = 0.8. At low k, the flowfield appears quasi-steady and the bluff body shedding corresponding to the maximum alpha (25 deg) dominates the unsteady fluctuations in the wake.

Panda, J.↗

Statistical Ensemble of Large Eddy Simulations

A statistical ensemble of large eddy simulations (LES) is run simultaneously for the same flow. The information provided by the different large scale velocity fields is used to propose an ensemble averaged version of the dynamic model. This produces local model parameters that only depend on the statistical properties of the flow. An important property of the ensemble averaged dynamic procedure is that it does not require any spatial averaging and can thus be used in fully inhomogeneous flows. Also, the ensemble of LES's provides statistics of the large scale velocity that can be used for building new models for the subgrid-scale stress tensor. The ensemble averaged dynamic procedure has been implemented with various models for three flows: decaying isotropic turbulence, forced isotropic turbulence, and the time developing plane wake. It is found that the results are almost independent of the number of LES's in the statistical ensemble provided that the ensemble contains at least 16 realizations.

Carati, Daniele↗

Modeling Tool Advances Rotorcraft Design

Continuum Dynamics Inc. (CDI), founded in 1979, specializes in advanced engineering services, including fluid dynamic modeling and analysis for aeronautics research. The company has completed a number of SBIR research projects with NASA, including early rotorcraft work done through Langley Research Center, but more recently, out of Ames Research Center. NASA Small Business Innovation Research (SBIR) grants on helicopter wake modeling resulted in the Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM), a tool for studying helicopter and tiltrotor unsteady free wake modeling, including distributed and integrated loads, and performance prediction. Application of the software code in a blade redesign program for Carson Helicopters, of Perkasie, Pennsylvania, increased the payload and cruise speeds of its S-61 helicopter. Follow-on development resulted in a $24 million revenue increase for Sikorsky Aircraft Corporation, of Stratford, Connecticut, as part of the company's rotor design efforts. Now under continuous development for more than 25 years, CHARM models the complete aerodynamics and dynamics of rotorcraft in general flight conditions. CHARM has been used to model a broad spectrum of rotorcraft attributes, including performance, blade loading, blade-vortex interaction noise, air flow fields, and hub loads. The highly accurate software is currently in use by all major rotorcraft manufacturers, NASA, the U.S. Army, and the U.S. Navy.

Source record↗

Heat Transfer in Gas Turbines

The turbine gas path is a very complex flow field. This is due to a variety of flow and heat transfer phenomena encountered in turbine passages. This manuscript provides an overview of the current work in this field at the NASA Glenn Research Center. Also, based on the author's preference, more emphasis is on the computational work. There is much more experimental work in progress at GRC than that reported here. While much has been achieved, more needs to be done in terms of validating the predictions against experimental data. More experimental data, especially on film cooled and rough turbine blades, are required for code validation. Also, the combined film cooling and internal cooling flow computation for a real blade is yet to be performed. While most computational work to date has assumed steady state conditions, the flow is clearly unsteady due to the presence of wakes. All this points to a long road ahead. However, we are well on course.

Garg, Vijay K.↗

Identifying Ultra Low Frequency Waves in the Lunar Plasma Environment Using Trajectory Analysis and Resonance Conditions

Abstract Recent studies show that localized crustal magnetic fields on the lunar surface can reflect a significant portion of the incoming solar wind protons. These reflected ions can drive a wide range of plasma waves. It is difficult to determine the intrinsic properties of low-frequency waves with single-spacecraft observations, which can be heavily Doppler shifted. We describe a technique to combine trajectory analysis of reflected protons with the Doppler shift and resonance conditions to identify ultralow-frequency waves at the Moon. On 31 January 2014 plasma waves were detected by one of the Acceleration, Reconnection, Turbulence and Electrodynamics of the Moon's Interaction with the Sun (ARTEMIS) probes as it approached the lunar wake; these waves were not detected by the second ARTEMIS probe located upstream in the undisturbed solar wind. The observed waves had a frequency below the local ion cyclotron frequency and had right-hand circular polarization in the reference frame of the Moon. By solving the Doppler shift and the cyclotron resonance equations, we determined the conditions for reflected ions to excite the observed waves. Simulated trajectories of reflected ions correspond to ARTEMIS ion observations and support the hypothesis that reflected ions are the primary driver of the waves. By combining trajectory analysis with the resonance conditions, we identify scenarios where ions that satisfy the resonance conditions are present in the right location to generate the observed waves. Using this method, we can uniquely identify the observed waves as upstream propagating right-hand polarized waves, subject to the assumption that they are generated by cyclotron resonance with ions.

Magnetic↗

Automated Fluid Feature Extraction from Transient Simulations

In the past, feature extraction and identification were interesting concepts, but not required to understand the underlying physics of a steady flow field. This is because the results of the more traditional tools like iso-surfaces, cuts and streamlines were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of much interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one "snap-shot" of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for co-processing environments like pV3). And methods must be developed to abstract the feature and display it in a manner that physically makes sense. The following is a list of the important physical phenomena found in transient (and steady-state) fluid flow: (1) Shocks, (2) Vortex cores, (3) Regions of recirculation, (4) Boundary layers, (5) Wakes. Three papers and an initial specification for the (The Fluid eXtraction tool kit) FX Programmer's guide were included. The papers, submitted to the AIAA Computational Fluid Dynamics Conference, are entitled : (1) Using Residence Time for the Extraction of Recirculation Regions, (2) Shock Detection from Computational Fluid Dynamics results and (3) On the Velocity Gradient Tensor and Fluid Feature Extraction.

Haimes, Robert↗

Using Particle Image Velocimetry to Determine Turbulence Model Parameters

The primary parameter of a standard k-ϵ model, C μ , was calculated from stereoscopic particle image velocimetry (PIV) data for a supersonic jet exhausting into a transonic crossflow. This required the determination of turbulent kinetic energy, turbulent eddy viscosity, and turbulent energy dissipation rate. Image interrogation was optimized, with different procedures used for mean strain rates and Reynolds stresses, to produce useful turbulent eddy viscosity fields. The eddy viscosity was calculated by a least-squares fit to all components of the three-dimensional strain-rate tensor that were available from the PIV data. This eliminated artifacts and noise observed when using a single strain component. Local dissipation rates were determined via Kolmogorov’s similarity hypotheses and the second-order structure function. The eddy viscosity and dissipation rates were then combined to determine C μ . Considerable spatial variation was observed in C μ , with the highest values found in regions where turbulent kinetic energy was relatively low but where turbulent mixing was important, e.g., along the high-strain jet edges and in the wake region. This suggests that use of a constant C μ in modeling may lead to poor Reynolds stress predictions at mixing interfaces. A data-driven modeling approach that can predict this spatial variation of C μ based on known state variables may lead to improved simulation results without the need for calibration.

42 ENGINEERING↗

LV measurements with an advanced turboprop

Nonintrusive measurements of velocity about a spinner-propeller-nacelle configuration were made at a Mach number of 0.8. A laser velocimeter (LV) specifically developed for these measurements was used to determine the flow field of the advanced swept SR-3 propeller. The data will be used to study the flow and to verify computer prediction codes. The usefulness of the LV data in detecting flow anomalies and to substantiate the data quality was demonstrated. Some typical results are given. Mach number profiles at the entrance of the propeller are compared with theoretical predictions. The LV data is in excellent agreement with the axisymmetric, compressible, inviscid theory (without blades) ahead of the propeller except near the hub. The data indicate blade blockage near the spinner. Blade to blade variations in axial velocity for four radial positions at the propeller exist are also given. The large apparent wake near the hub is associated with the hub choking. The blade to blade variation of axial velocity ahead of a shock within the blade passage is given.

Neumann, H. E.↗