Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “protective structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
NASA NTRS1988

Expert system structures for fault detection in spaceborne power systems

This paper presents an architecture for an expert system structure suitable for use with power system fault detection algorithms. The system described is not for the purpose of reacting to faults which have occurred, but rather for the purpose of performing on-line diagnostics and parameter evaluation to determine potential or incipient fault conditions. The system is also designed to detect high impedance or arcing faults which cannot be detected by conventional protection devices. This system is part of an overall monitoring computer hierarchy which would provide a full evaluation of the status of the power system and react to both incipient and catastrophic faults. An approximate hardware structure is suggested and software requirements are discussed. Modifications to CLIPS software, to capitalize on features offered by expert systems, are presented. It is suggested that such a system would have significant advantages over existing protection philosophy.

Watson, Karan↗
NASA NTRS2002

Reliability Analysis of Brittle Material Structures - Including MEMS(?) - With the CARES/Life Program

Brittle materials are being used, or considered, for a wide variety of high tech applications that operate in harsh environments, including static and rotating turbine parts. thermal protection systems, dental prosthetics, fuel cells, oxygen transport membranes, radomes, and MEMS. Designing components to sustain repeated load without fracturing while using the minimum amount of material requires the use of a probabilistic design methodology. The CARES/Life code provides a general-purpose analysis tool that predicts the probability of failure of a ceramic component as a function of its time in service. For this presentation an interview of the CARES/Life program will be provided. Emphasis will be placed on describing the latest enhancements to the code for reliability analysis with time varying loads and temperatures (fully transient reliability analysis). Also, early efforts in investigating the validity of using Weibull statistics, the basis of the CARES/Life program, to characterize the strength of MEMS structures will be described as as well as the version of CARES/Life for MEMS (CARES/MEMS) being prepared which incorporates single crystal and edge flaw reliability analysis capability. It is hoped this talk will open a dialog for potential collaboration in the area of MEMS testing and life prediction.

Nemeth, Noel N.↗
DOE OSTI2022

Structures of drug-specific monoclonal antibodies bound to opioids and nicotine reveal a common mode of binding

Opioid-related fatal overdoses have reached epidemic proportions. Because existing treatments for opioid use disorders offer limited long-term protection, accelerating the development of newer approaches is critical. Monoclonal antibodies (mAbs) are an emerging treatment strategy that targets and sequesters selected opioids in the bloodstream, reducing drug distribution across the blood-brain barrier, thus preventing or reversing opioid toxicity. We previously identified a series of murine mAbs with high affinity and selectivity for oxycodone, morphine, fentanyl, and nicotine. To determine their binding mechanism, we used X-ray crystallography to solve the structures of mAbs bound to their respective targets, to 2.2 Å resolution or higher. Structural analysis showed a critical convergent hydrogen bonding mode that is dependent on a glutamic acid residue in the mAbs’ heavy chain and a tertiary amine of the ligand. Further, characterizing drug-mAb complexes represents a significant step toward rational antibody engineering and future manufacturing activities to support clinical evaluation.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

High power pulse systems for surface processing

A high-power pulsed surface processing system includes insulated-gate bipolar transistors (IGBT) to replicate desirable pulse structures with high precision, at low cost, and with high reliability within a single system. The pulsed surface processing system includes a power supply, an anode and a cathode, a dual gate driver supplying power to one or more IGBT gates, and one or more capacitor banks. Pulse formation software controls the timing and duration of electrical pulses to the electrodes. A freewheeling diode protects the system from an abrupt reduction of current in the circuit. The high-power pulsed surface processing system may be used to control versatile and complex pulse structures while with precise control of instantaneous pulse powers, pulse timing, and process control. The inclusion of dual gate drivers also offers the ability for multiple pulsers to be created and “slaved” together for a wide variety of custom processes.

Tian, Hui↗
DOE OSTI2023

Nanostructure‐Derived Antireflectivity in Leafhopper Brochosomes

Understanding how insect‐derived biomaterials interact with light has led to new advances and interdisciplinary insights in entomology and physics. Leafhoppers are insects that coat themselves with highly ordered biological nanostructures known as brochosomes. Brochosomes are thought to provide a range of protective properties to leafhoppers, such as hydrophobicity and antireflectivity, which has inspired the development of synthetic brochosomes that mimic their structures. Despite recent progress, the high antireflective properties of brochosome structures are not fully understood. Herein, a combination of experiments and computational modeling is used to understand the structure‐, material‐, and polarization‐dependent optical properties of brochosomes modeled on the geometries found in three leafhopper species. The results qualitatively represent that light interference interaction with nanostructures naturally occurring in brochosomes is responsible for the spectral tuning and the asymmetric line shape of the reflectance spectra. Whereas prior work has focused on the computational modeling of idealized pitted particles, this work shows that light–matter interactions with brochosome structures can be tuned by varying the geometry of their cage‐like nanoscale features and by changing the arrangement of multiparticle assemblies. Broadly, this work establishes principles for the guided design of new optically active materials inspired by these unique insect nanostructures.

Banerjee, Progna↗
DOE OSTI2020

Mechanical and chemical properties of PVD and cold spray Cr-coatings on Zircaloy-4

In this paper, accident-tolerant fuel (ATF) cladding materials aim to improve fuel reliability and safety during accident scenarios in water-cooled reactors. These ATF cladding should also perform comparable or better than the current zirconium alloy cladding under reactor normal operating conditions. Surface-modified Zircaloy-4 was produced by depositing a protective coating of chromium by two different coating techniques, Physical Vapor Deposition (PVD) and Cold Spray (CS). The coating thickness, structure, composition, and mechanical properties of the coated Zircaloy were assessed with advanced materials characterization techniques. Results showed a strengthening effect of the Cr-coating, along with ~83% higher hardness compared to that of the Zircaloy-4 substrate. Surface topography and surface chemistry of the Cr-coated Zircaloy-4 were assessed with contact profilometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy. Deposited Cr-coating significantly improved surface wettability compared to the substrate Zircaloy-4. The formation of surface oxides on the coatings by prolonged exposure to ambient air showed a further increase in the hydrophobic behavior. Surface parameters and surface chemistry after flow boiling critical heat flux tests, conducted at atmospheric pressure, evidenced a slight increase in surface roughness with notable changes in wettability associated with the formation of surface oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Observation of a linked-loop quantum state in a topological magnet

Quantum phases can be classified by topological invariants, which take on discrete values capturing global information about the quantum state. Over the past decades, these invariants have come to play a central role in describing matter, providing the foundation for understanding superfluids, magnets, the quantum Hall effect, topological insulators, Weyl semimetals and other phenomena. Here we report an unusual linking-number (knot theory) invariant associated with loops of electronic band crossings in a mirror-symmetric ferromagnet. Using state-of-the-art spectroscopic methods, we directly observe three intertwined degeneracy loops in the material's three-torus, T 3 , bulk Brillouin zone. We find that each loop links each other loop twice. Through systematic spectroscopic investigation of this linked-loop quantum state, we explicitly draw its link diagram and conclude, in analogy with knot theory, that it exhibits the linking number (2, 2, 2), providing a direct determination of the invariant structure from the experimental data. Here we further predict and observe, on the surface of our samples, Seifert boundary states protected by the bulk linked loops, suggestive of a remarkable Seifert bulk-boundary correspondence. Our observation of a quantum loop link motivates the application of knot theory to the exploration of magnetic and superconducting quantum matter.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Skyrmion lattice formation and destruction mechanisms probed with TR-SANS

Magnetic skyrmions are topologically protected, nanoscale whirls of the spin configuration that tend to form hexagonally ordered arrays. As a topologically non-trivial structure, the nucleation and annihilation of the skyrmion, as well as the interaction between skyrmions, varies from conventional magnetic systems. Recent works have suggested that the ordering kinetics in these materials occur over millisecond or longer timescales, which is unusually slow for magnetic dynamics. The current work investigates the skyrmion ordering kinetics, particularly during lattice formation and destruction, using time-resolved small angle neutron scattering (TR-SANS). Evaluating the time-resolved structure and intensity of the neutron diffraction pattern reveals the evolving real-space structure of the skyrmion lattice and the timeframe of the formation. Measurements were performed on three prototypical skyrmion materials: MnSi, (Fe,Co)Si, and Cu 2 OSeO 3 . To probe lattice formation and destruction kinetics, the systems were prepared in the stable skyrmion state, and then a square-wave magnetic field modulation was applied. The measurements show that the skyrmions quickly form ordered domains, with a significant distribution in lattice parameters, which then converge to the final structure; the results confirm the slow kinetics, with formation times between 10 ms and 99 ms. Comparisons are made between the measured formation times and the fundamental material properties, suggesting the ordering temperature, saturation magnetization and magnetocrystalline anisotropy may be driving the timeframes. Micromagnetic simulations were also performed and support a scaling of the kinetics with sample volume, a behavior which is caused by the reconciling of misaligned domains.

Liyanage, W. L. N. C.↗
DOE OSTI2021

Thermal stress reduces carbonate production of benthic foraminifera and changes the material properties of their shells

Abstract In shallow marine environments, benthic foraminifera are important foundation species and carbonate producers. Understanding their response to future climate is often drawn from their acclimation potential in short laboratory experiments, thereby limiting our understanding of migration, species replacement, and adaptive potential. To overcome this challenge, we examine two species of benthic foraminifera from a thermally polluted field site mimicking future warming. This site and a control station cover 13–36°C causing both warm and cold stress to the local species. Computer Tomography reveals that under heat stress, even with acclimation, Lachlanella significantly reduced its shell volume. In contrast, Pararotalia calcariformata did not reduce its shell volume but reduced the relative amount of calcite with respect to shell volume and changed its reproduction cycle from twice to once per year. Raman spectroscopy indicates that thermal conditions alter the chemical composition of the calcite shells of both species. Calcification during thermal stress creates alterations in the crystal structure that are unexpectedly more prominent under cold stress than warm stress indicating warming might positively affect the shell's protective function. Supported by previous laboratory experiments and observations from the geological record, our results provide new perspective to the effect of warming on benthic foraminifera.

Titelboim, Danna↗
NASA NTRS1973

Development, fabrication and evaluation of composite thermal engine insulation

Foil enclosure configurations of 10 variations were fabricated and evaluated. A discussion of the thermal protection system panel design includes: (1) description of 3DSX/foil concept, (2) design environment, (3) material selection, (4) fabrication enclosure, (5) structural design, (6) thermal sizing, and (7) weight analysis. The structural design study includes foil evaluation, venting pressure loads, thermomechanical behavior, and enclosure venting (burst) pressure tests. Results of experimental demonstrations of performance and reuse capabilities are given for both thermal and acoustic testing.

Source record↗
NASA NTRS1976

Status of research into lightning effects on aircraft

Developments in aircraft lightning protection since 1938 are reviewed. Potential lightning problems resulting from present trends toward the use of electronic controls and composite structures are discussed, along with presently available lightning test procedures for problem assessment. The validity of some procedures is being questioned because of pessimistic results and design implications. An in-flight measurement program is needed to provide statistics on lightning severity at flight altitudes and to enable more realistic tests, and operators are urged to supply researchers with more details on electronic components damaged by lightning strikes. A need for review of certain aspects of fuel system vulnerability is indicated by several recent accidents, and specific areas for examination are identified. New educational materials and standardization activities are also noted.

Plumer, J. A.↗
NASA NTRS1980

Erosion of composite materials

A model for describing the response of uncoated and coated fiber reinforced composites subjected to repeated impingements of liquid (rain) droplets is presented. The model is based on the concept that fatigue is the dominant factor in the erosion process. Algebraic expressions are provided which give the incubation period, the rate of mass loss past the incubation period, and the total mass loss of the material during rain impact. The influence of material properties on erosion damage and the protection offered by different coatings are discussed and the use of the model in the design in the design of structures and components is illustrated.

Springer, G. S.↗
NASA NTRS1990

The effects of the space environment on two aramid materials

Two aramid fibers having closely related chemical structures were chosen for important roles in the first tether to be used to connect pairs of orbiting vehicles. The protective outer jackets of the tethers will consist of woven fibers of poly(m-phenylene isophthalamide), commercially available from du Pont as Nomex. A cylindrical sheath of woven Kevlar 29, whose principal constituent is poly(p-phenylene terephthalamide), will be the load-bearing component for the tethers. Orbiting tethers will be in a hostile environment in which short wavelength electromagnetic radiation and energetic charged particles degrade exposed organic materials. At lower orbiting altitudes atomic oxygen is an especially serious hazard. Studies on the effects of ultraviolet radiation and atomic oxygen on fibers and films of Kevlar and Nomex are in progress. In an experiment to simulate the effects of atomic oxygen in space, small tows of Kevlar and Nomex were mounted in a commercial ashing device filled with oxygen at low pressure. An RF discharge in the instrument dissociated the molecular oxygen producing a strongly oxidizing atmosphere containing O(3P)(sup 4). Erosion was measured in terms of mass loss. Kevlar films were exposed to UV radiation in an apparatus consisting of a small vacuum chamber, 23 cm in diameter, into which a mass spectrometer and a quartz window were incorporated. Samples were exposed under vacuum with a 1000 watt xenon-arc lamp. Volatile products could be monitored with the mass spectrometer during the exposures. Transmission infrared spectra were taken before and after exposure to monitor chemical changes in the films.

Kiefer, Richard L.↗
NASA NTRS1995

Hydroxycinnamic acid-derived polymers constitute the polyaromatic domain of suberin

Suberin is an abundant, complex, intractable, plant cell wall polymeric network that forms both protective and wound-healing layers. Its function is, therefore, critical to the survival of all vascular plants. Its chemical structure and biosynthesis are poorly defined, although it is known to consist of both aromatic and aliphatic domains. While the composition of the aliphatic component has been fairly well characterized, that of the phenolic component has not. Using a combination of specific carbon-13 labeling techniques, and in situ solid state 13C NMR spectroscopic analysis, we now provide the first direct evidence for the nature of the phenolic domain of suberin and report here that it is almost exclusively comprised of a covalently linked, hydroxycinnamic acid-derived polymeric matrix.

NASA Discipline Plant Biology↗
DOE OSTI2025

The effect of copper additives on hybrid Zr-based chemical conversion coating morphology and chemical compositions

In the realm of corrosion protection, Zr-based conversion coatings offer an environmentally friendly, chromate-free alternative to conventional coating. This study uses advanced X-ray, electron microscopy and electrochemical testing techniques to better understand the impact of varying Cu²⁺ ion concentrations on the characteristics of Zr-based coatings on Fe substrates. Our findings demonstrate that within the tested conditions, higher Cu²⁺ additive concentrations at 40 ppm enhance surface characteristics, increasing stability towards anti-corrosion capability, particularly under NaCl treatment. Conversely, at a lower Cu²⁺ concentration of 20 ppm, coatings exhibited more significant dissolution of Cu clusters and increased vulnerability to chloride-induced degradation. X-ray photoelectron spectroscopy and synchrotron X-ray fluorescence (XRF) and X-ray absorption near edge structure (XANES) spectroscopy analyses revealed Cu²⁺ formation in Cu20, while Cu40 retained its metallic state (Cu⁰) with a slower reaction rate. Cu20 offers some protection but lacks durability, whereas in Cu40, lower I corr , and enhance corrosion resistance, making it ideal for protective coatings in salt-water environments. This study underscores the importance of balancing Cu²⁺ ions concentration in the coating solution to optimize performance, highlighting the role of Cu in enhancing both surface properties and long-term stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Selective inhibition of cullin 3 neddylation through covalent targeting DCN1 protects mice from acetaminophen-induced liver toxicity

Cullin-RING E3 ligases (CRLs) regulate the turnover of approximately 20% of mammalian cellular proteins. Neddylation of individual cullin proteins is essential for the activation of each CRL. We report herein the discovery of DI-1548 and DI-1859 as two potent, selective and covalent DCN1 inhibitors. These inhibitors selectively inhibit neddylation of cullin 3 in cells at low nanomolar concentrations and are 2–3 orders of magnitude more potent than our previously reported reversible DCN1 inhibitor. Mass spectrometric analysis and co-crystal structures reveal that these compounds employ a unique mechanism of covalent bond formation with DCN1. DI-1859 induces a robust increase of NRF2 protein, a CRL3 substrate, in mouse liver and effectively protects mice from acetaminophen-induced liver damage. Taken together, this study demonstrates the therapeutic potential of selective inhibition of cullin neddylation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Single-crystalline orthorhombic GdAlGe as a rare-earth magnetic Dirac nodal-line metal

Crystal engineering is a method for discovering new quantum materials and phases, which may be achieved using external pressure or strain. Chemical pressure is unique in that it generates internal pressure perpetually to the lattice. As an example, GdAlSi from the rare-earth (𝑅) 𝑅⁢Al⁢𝑋 (𝑋=Si or Ge) family of Weyl semimetals is considered. Replacing Si with the larger isovalent element Ge creates sufficiently large chemical pressure to induce a structural transition from the tetragonal structure of GdAlSi, compatible with a Weyl semimetallic state, to an orthorhombic phase in GdAlGe, resulting in an inversion-symmetry-protected nodal-line metal. We find that GdAlGe hosts an antiferromagnetic ground state with two successive orderings, at 𝑇 N ⁢1=35K and 𝑇 N ⁢2=30K. In-plane isothermal magnetization shows a magnetic field induced metamagnetic transition at 6.2 T for 2 K. Furthermore, electron-hole compensation gives rise to a large magnetoresistance of ∼100% at 2 K and 14 T. Angle-resolved photoemission spectroscopy measurements and density functional theory calculations reveal a Dirac-like linear band dispersion over an exceptionally large energy range of ∼1.5eV with a high Fermi velocity of ∼10 6 m/s, a rare feature not observed in any magnetic topological materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗