Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “physical layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Interferometric observations of Saturn and its rings at a wavelength of 3.71 per cm

Interferometric observations of Saturn and its rings obtained at the Owens Valley Radio Observatory at a wavelength of 3.71 cm (8085 MHz) are presented. Models of the microwave brightness structure of the Saturn system are fit to the observations in order to estimate the brightness temperatures of the planet and its rings. The models allowed making estimates of the brightness temperatures and optical depths of the A, B, and C rings. The ring brightness temperatures and optical depths are compared with a physical ring model of isotropic scatterers in a layer which is many particles thick. The observations are consistent with particles that conservatively scatter the thermal emission from Saturn to the earth and emit no thermal radiation of their own. However, the particle single-scattering albedo that would be most consistent with the observations is slightly less than unity but probably greater than 0.95. There is evidence indicating that the ring particles must be at least a few centimeters in size.

Schloerb, F. P.↗
NASA NTRS1986

Factors which influence the development of a low-level jet and coastal cyclogenesis

Mesoscale model simulations were run to examine the mechanisms which generate a low-level jet (LLJ) and the sea-level pressure decrease (SLPD) associated with secondary cyclogenesis along the East Coast of the U.S. Data collected during the Presidents' Day cyclone of February 18-19, 1979 are reviewed, including the behavior of the LLJ preceding cyclogenesis. The simulations covered adiabatic conditions, the absence and presence of latent heating, and the inclusion of all physical parameters with and without computations of boundary layer phenomena, 60-km grid-scale precipitation, and convective precipitation. The results indicate that synergistic reactions among the LLJ, latent heat release, jet-induced circulation, and boundary layer processes are necessary to account for secondary cyclogenesis and the accompanying rapidly evolving mass, momentum and moisture fields.

Uccellini, Louis W.↗
NASA NTRS1987

Processes associated with the plasma sheet boundary layer

The plasma sheet boundary is an important region of energy and mass transfer in the magnetotail. It is probably formed by energized ions ejected from the cross-tail current sheet. Processes associated with the boundary layer are important to many areas of magnetospheric physics. These areas include energetic particles, plasma sheet sources, auroral precipitation, field-aligned currents and discrete auroral arcs, and substorm initiation.

Lyons, L. R.↗
NASA NTRS1990

Comparison of measurements and theory for backscatter from bare and snow-covered saline ice

C-band radar backscatter measurements were made on artificially grown sea ice during the winters of 1987-1988 and 1988-1989. These measurements were made on smooth, rough, and snow-covered saline ice. The measured sigma-deg(theta) of smooth saline ice (rms height less than 0.05 cm) disagreed with small perturbation method (SPM) surface scattering predictions. Using physical parameters of the ice in a simple layer model, it us shown that this discrepancy can be explained by scattering from beneath the surface. A thin (7-cm) dry snow cover had a significant influence on backscatter from the smooth ice sheet. This influence was due to scattering from particles within the snow, and can be predicted by a commonly used empirical layer model for snow. The results of backscatter measurements of a moderately rough saline ice sheet were found to agree with SPM predictions.

Bredow, Jonathan W.↗
NASA NTRS1990

Direct simulations of wall-bounded compressible turbulence

A study has been initiated on the effects of compressibility (Mach number) on turbulent boundary layers. An understanding of both qualitative (turbulence structures, physical processes) and quantitative (turbulence statistics) effects are desired. This understanding should lead to better turbulence models for applications involving supersonic wall-bounded flows. Direct numerical simulations of an idealized problem will be used to accomplish these objectives. Among several possibilities we chose plane Couette flow with constant-temperature walls as the first problem to be studied. The lack of mean streamwise pressure gradient plus isothermal walls implies that both horizontal directions can be assumed to be homogeneous and that the flow can reach a statistically steady state. Together, these features greatly simplify the calculations and analyses of the results. To date, an algorithm has been developed and implemented (but not yet fully tested) for the accurate solution of the Navier-Stokes equations with the assumptions noted above.

Buell, J. C.↗
NASA NTRS1992

Development of an improved model for runback water on aircraft surfaces

A computer simulation for 'running wet' and evaporative aircraft anti-icing systems is developed. The model is based on the analysis of the liquid water film which forms in the regions of direct impingement and, then, breaks up near the impingement limits into rivulets. The wetness factor distribution resulting from the film breakup and the rivulet configuration on the surface are predicted using a stability analysis theory and the laws of mass energy conservation. The solid structure is modeled as a multiple layer wall. The anti-icing system modeled is of the thermal type utilizing hot air and/or electrical heating elements embedded within the wall layers. Experimental observations revealing some of the basic physics of the water flow on the surface are presented. Detailed qualitative documentation of the tests are given. Several numerical examples are considered, and the effect of some of the involved parameters on the system performance are investigated.

Al-Khalil, Kamel M.↗
NASA NTRS1992

Some effects of oscillation waveform and amplitude on unsteady turbulent shear flows

Some physical features of several unsteady separating turbulent boundary layers are presented for practical Reynolds numbers and reduced frequencies such as for helicopter and turbomachinery flows. The effects of unsteadiness amplitude and waveform are examined for flows along the floor of a converging and diverging wind tunnel test section. At the end of the converging portion, the mean skin friction coefficient normalized on the mean dynamic pressure is independent of the waveform and amplitude within low experimental uncertainties. In the detaching and detached portions of the flow, wall values of the fraction of time that the flow moves downstream of gamma sub pu, which is a separated flow state variable, shows that oscillation waveform and amplitude strongly influence the detached flow behavior. Distributions of gamma sub pu during a cycle indicate hysteresis within the detached flow and the effects of the higher harmonics of pressure gradient and velocity.

Agarwal, Naval K.↗
NASA NTRS1993

The roughness of the Martian surface: A scale dependent model

In the coming decade, several lander missions to Mars are planned (e.g., MESUR Pathfinder, MESUR). One of the dangers facing planners of these missions is the rough topography observed at both Viking Lander sites. Both landing sites are ubiquitously covered with meter-scale boulders. Objects of this size pose obvious threats to soft landers, especially at Mars where the distance from Earth causes prohibitive time lags between the transmission of commands and feedback from the spacecraft. An obvious solution is to scout for a 'smooth' site prior to the landing. However, the best resolutions realizable on current and future missions (i.e., Mars Observer) are on the order of several meters. Even at this scale, boulders of 1-2 meters in size are unresolvable. Additionally, the amount of time and spacecraft resources required to search even a small area of the planet are unrealistic given other mission objectives. An alternative is to determine the 'roughness' of the surface at a subpixel scale using bidirectional reflectance observations. Much larger areas of the planet can be searched, and much of the search can easily be automated. The morphology of the martian plains observed by the Viking Landers is physically simple. The surface is covered with a layer (approximately flat lying) of aeolian sediment from which numerous outcrops of bedrock and boulders protrude. This morphology, while simple, will be difficult to characterize from orbit using traditional bidirectional reflectance models for two reasons. First, modeling the surface as facets with Gaussian or exponential slope distributions is not realistic given the morphology described above. Second, the roughness parameter is an 'average' of the roughness at scales ranging from the wavelength of light being scattered to the pixel size of the observation. Thus, there is no definite scale of roughness that can be extracted from the Hapke roughness parameter. Using the concepts of geometric and boolean models developed by several workers, we have developed a model for the bidirectional reflectance of a surface morphology comparable to that observed at the Viking Lander sites.

Shepard, M. K.↗
NASA NTRS1993

SPARTAN high resolution solar studies

This report summarizes the work performed on Contract NAS5-29739, a sub-orbital research program directed toward the study of the geometry of and physical conditions in matter found in the upper layers of the solar atmosphere. The report describes a new sounding rocket payload developed under the contract, presents a guide to the contents of semiannual reports submitted during the contract, discusses the results of the first flight of the payload and the progress on scientific analysis. A bibliography of papers and publications is included.

Bruner, Marilyn E.↗
NASA NTRS1994

The CCSDS return all frames Space Link Extension service

Existing Consultative Committee for Space Data Systems (CCSDS) Recommendations for Telemetry Channel Coding, Packet Telemetry, Advanced Orbiting Systems, and Telecommand have facilitated cross-support between Agencies by standardizing the link between spacecraft and ground terminal. CCSDS is currently defining a set of Space Link Extension (SLE) services that will enable remote science and mission operations facilities to access the ground termination of the Space Link services in a standard manner. The first SLE service to be defined is the Return All Frames (RAF) service. The RAF service delivers all CCSDS link-layer frames received on a single space link physical channel. The service provides both on-line and off-line data transfer modes to accommodate the variety of access methods typical of space mission operations. This paper describes the RAF service as of the Summer of 1994. It characterizes the behavior of the service as seen across the interface between the user and the service and gives an overview of the interactions involved in setting up and operating the service in a cross-support environment.

Uhrig, Hans↗
NASA NTRS1996

Application of the pressure sensitive paint technique to steady and unsteady flow

Pressure sensitive paint is a newly-developed optical measurement technique with which one can get a continuous pressure distribution in much shorter time and lower cost than a conventional pressure tap measurement. However, most of the current pressure sensitive paint applications are restricted to steady pressure measurement at high speeds because of the small signal-to-noise ratio at low speed and a slow response to pressure changes. In the present study, three phases of work have been completed to extend the application of the pressure sensitive paint technique to low-speed testing and to investigate the applicability of the paint technique to unsteady flow. First the measurement system using a commercially available PtOEP/GP-197 pressure sensitive paint was established and applied to impinging jet measurements. An in-situ calibration using only five pressure tap data points was applied and the results showed good repeatability and good agreement with conventional pressure tap measurements on the whole painted area. The overall measurement accuracy in these experiments was found to be within 0.1 psi. The pressure sensitive paint technique was then applied to low-speed wind tunnel tests using a 60 deg delta wing model with leading edge blowing slots. The technical problems encountered in low-speed testing were resolved by using a high grade CCD camera and applying corrections to improve the measurement accuracy. Even at 35 m/s, the paint data not only agreed well with conventional pressure tap measurements but also clearly showed the suction region generated by the leading edge vortices. The vortex breakdown was also detected at alpha=30 deg. It was found that a pressure difference of 0.2 psi was required for a quantitative pressure measurement in this experiment and that temperature control or a parallel temperature measurement is necessary if thermal uniformity does not hold on the model. Finally, the pressure sensitive paint was applied to a periodically changing pressure field with a 12.8s time period. A simple first-order pole model was applied to deal with the phase lag of the paint. The unsteady pressure estimated from the time-changing pressure sensitive paint data agreed well with the pressure transducer data in regions of higher pressure and showed the possibility of extending the technique to unsteady pressure measurements. However, the model still needs further refinement based on the physics of the oxygen diffusion into the paint layer and the oxygen quenching on the paint luminescence.

Shimbo, Y.↗
NASA NTRS2000

Geometric Perturbations and Asymmetric Vortex Shedding about Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approx. = 40 deg.), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approx. = 60 deg.), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90 deg., the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40 deg. and alpha = 60 deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60 deg. which is consistent with the application of a tip bump, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft. portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40 deg., and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗
NASA NTRS2000

Geometric Perturbations and Asymmetric vortex shedding About Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approximately equals 40deg), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approximately equals 60deg), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90deg, the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40deg and alpha = 60deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60deg which is consistent with the application of a tip bumps, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40deg, and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗
NASA NTRS2000

Space Environmentally Stable Polyimides and Copolyimides

Polyimides with a unique combination of properties including low color in thin films, atomic oxygen (AO), ultra-violet (UV) radiation resistance, solubility in organic solvents in the imide form, high glass transition (T(sub g)) temperatures and high thermal stability have been prepared and characterized. The polymers were prepared by reacting a novel aromatic diamine with aromatic dianhydrides in a polar aprotic solvent. The solubility of the polymers in the imide form as well as the color density of thin films were dependent upon the chemical structure of the dianhydride. Several thin films (25-50 mm thick) prepared by solution casting of amide acid or imide solutions exhibited very low color and high optical transparency (approximately 90%) as determined by UV/visible spectroscopy. The polymers exhibited T(sub g)s >200 C depending upon the structure of the dianhydride and temperatures of 5% weight loss approximately 500C in air as determined by dynamic thermogravimetric analysis. Thin films coated with silver/inconel were exposed to a high fluence of AO and 1000 equivalent solar hours of UV radiation. The effects of these exposures on optical properties were minor. These space environmentally durable polymers are potentially useful in a variety of applications on spacecraft such as thin film membranes on antennas, second-surface mirrors, thermal/optical coatings and multi-layer thermal insulation (MLI) blanket materials. The chemistry, physical and mechanical properties of the polymers as well as their responses to AO and UV exposure will be discussed.

Watson, Kent A.↗
NASA NTRS2008

Forebody and Inlet Design for the HIFiRE 2 Flight Test

A forebody and inlet have been designed for the HIFiRE 2 scramjet flight test. The test will explore the operating, performance, and stability characteristics of a simple hydrocarbon-fueled scramjet combustor as it transitions from dual-mode to scramjet-mode operation and during supersonic combustion at Mach 8+ flight conditions. Requirements for the compression system were derived from inlet starting and combustor inflow requirements as well as physical size constraints. The design process is described. A planar, fixed geometry, mixed compression concept was used to produce laterally uniform flow at the inlet entrance and a conservative amount of internal contraction with respect to inlet starting. A grid sensitivity study was performed so that important flow physics caused by three-dimensional shock boundary layer interactions could be captured with confidence. Results from low Mach number operability studies, nominal trajectory cases, and high dynamic pressure heat load cases are discussed. The forebody and inlet solutions provide information for on-going combustor calculations, mass capture across the trajectory for fuel system design, and surface heating rates for thermal/structural analysis. The design has a one freestream Mach number margin for inlet starting, exceeds the high Mach number combustor entrance pressure requirement, produces high quality flow at the inlet exit for all Mach numbers and vehicle attitudes in the design space, and fits inside the booster shroud.

Ferlemann, Paul G.↗
NASA NTRS2005

Multicomponent, Rare-Earth-Doped Thermal-Barrier Coatings

Multicomponent, rare-earth-doped, perovskite-type thermal-barrier coating materials have been developed in an effort to obtain lower thermal conductivity, greater phase stability, and greater high-temperature capability, relative to those of the prior thermal-barrier coating material of choice, which is yttria-partially stabilized zirconia. As used here, "thermal-barrier coatings" (TBCs) denotes thin ceramic layers used to insulate air-cooled metallic components of heat engines (e.g., gas turbines) from hot gases. These layers are generally fabricated by plasma spraying or physical vapor deposition of the TBC materials onto the metal components. A TBC as deposited has some porosity, which is desirable in that it reduces the thermal conductivity below the intrinsic thermal conductivity of the fully dense form of the material. Undesirably, the thermal conductivity gradually increases because the porosity gradually decreases as a consequence of sintering during high-temperature service. Because of these and other considerations such as phase transformations, the maximum allowable service temperature for yttria-partially stabilized zirconia TBCs lies in the range of about 1,200 to 1,300 C. In contrast, the present multicomponent, rare-earth-doped, perovskite-type TBCs can withstand higher temperatures.

Miller, Robert A.↗
NASA NTRSDate not supplied

An Electron Backscatter Diffraction (EBSD)-Based Automated Tool for Ceramic Capacitor Grain Size Analysis

Ceramic capacitors continue to be recurring problem parts for NASA, despite best efforts to screen out potential defects and failures through environmental and electrical testing and nondestructive inspection techniques such as acoustic microscopy. The physical properties of ceramic capacitors necessitates thin dielectric layers capable of withstanding significant electric fields. Any defects in those ceramic layers can result in reduced insulation resistance failure modes including short circuit failures, so the quality and consistency of the dielectric material is critical. The size of the individual ceramic grains in the dielectric material is a critical parameter. However, judging “grain size” is not so simple—in a single capacitor there can be wide variation in grain sizes observed. It is theorized that by studying the grain size distributions of “known good” and “known bad” lots of capacitors, some conclusions could be drawn that would allow us to better predict to the reliability of future lots based on grain size distributions. The initial goal of this effort was to find or develop an automated tool that could inspect a capacitor and return grain size distribution results.

Robert Hodson↗