Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Investigation of Fuel Staging Effect on Modal Dynamics of Thermoacoustic Azimuthal Instabilities in a Multi-Nozzle Can Combustor

Abstract This paper analyzes the dynamics of unstable azimuthal thermoacoustic modes in a lean premixed combustor. Azimuthal modes can be decomposed into two counter rotating waves where they can either compete and potentially suppress one of them (spinning) or coexist (standing), depending on the operating conditions. This paper describes experimental results of the dynamical behaviors of these two waves. The experimental data were taken at different mass flow rates as well as different azimuthal fuel staging in a multi-nozzle can combustor. It is shown that at a low flow rate with uniform fuel distribution, the two waves have similar amplitudes, giving rise to a standing wave. However, the two amplitudes are slowly oscillating out of phase to each other, and the phase difference between the two waves also shows oscillatory behavior. For an intermediate flow rate, the dynamics show intermittency between standing and spinning waves, indicating that the system is bistable. In addition, the phase difference dramatically shifts when the mode switches between standing and spinning waves. For a high flow rate, the system stabilizes at a spinning wave most of the time. These experimental observations demonstrate that not only the amplitudes of two waves but also the phase difference plays an important role in the dynamics of azimuthal mode. For non-uniform azimuthal fuel staging, the modal dynamics exhibit only an oscillatory standing wave behavior regardless of the mass flow rate. Compared to the uniform fuel staging, however, the pressure magnitude is considerably reduced, which provides a potential strategy to mitigate and/or suppress the instabilities.

Kim, J.↗
DOE OSTI2023

Structure and Stability of the Iodide Elpasolite, Cs 2 AgBiI 6

Iodide elpasolites (or double perovskites, A 2 B'B"I 6 , B' = M + , B" = M 3+ ) are predicted to be promising alternatives to lead-based perovskite semiconductors for photovoltaic and optoelectronic applications, but no iodide elpasolite has ever been definitively prepared or structurally characterized. Iodide elpasolites are widely predicted to be unstable due to favorable decomposition to the competing A 3 B 2 I 9 (B = M 3+ ) phase. Here, we report the results of synchrotron XRD and X-ray total scattering measurements on putative Cs 2 AgBiI 6 nanocrystals made via anion exchange from parent Cs 2 AgBiBr 6 nanocrystals. Rietveld refinement of XRD and PDF data shows that these nanocrystals indeed exhibit a tetragonal ($I$$\overline{4}$$m$) elpasolite structure, making them the first example of a structurally characterized iodide elpasolite. In conclusion, a series of experiments probing structural relaxation and the effects of surface ligation or grain size all point to the critical role of surface free energy in stabilizing the iodide elpasolite phase in these nanocrystals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Critical Clearing Time for Droop-Controlled Grid-Forming Inverters With Circular Current Limiting and Virtual Impedance Current Limiting

The critical clearing time is a crucial parameter for assessing the large-signal stability of grid-forming (GFM) inverters. Variations in current limiters can significantly impact an inverter's transient behavior during large disturbances. Here, this letter introduces a method based on the power-angle relationship to evaluate the fault recovery of a droop-controlled GFM inverter under a three-phase bolted fault scenario, considering both the circular current limiter and the virtual impedance method. High-fidelity simulations validate the accuracy of the proposed formulas in estimating the critical clearing time of the GFM inverter.

42 ENGINEERING↗
DOE OSTI2024

Heteroatom anchoring to enhance electrochemical reversibility for high-voltage P2-type oxide cathodes of sodium-ion batteries

P2-type cathode has received extensive attention due to its faster Na+ diffusion and a high theoretical capacity in sodium-ion batteries (SIBs). However, undesirable phase transformations have induced dramatic capacity decay of SIBs during the cycling process. In this study, heteroatom anchoring through Cu/Mg dual doping is introduced into P2-type Na 0.67 Ni 0.33 Mn 0.67 O 2 cathode to enhance high-voltage electrochemical reversibility and modulate interfacial Na + kinetics. Further, the as-prepared Na 0.67 Ni 0.23 Mg 0.05 Cu 0.05 Mn 0.67 O 2 exhibits an outstanding capacity retention (83.4% after 2000 cycles at 10C) and rate performance (73 mAh g -1 at 10C, accounting for 58.7% of that at 0.1 C) over the voltage range of 2.5–4.4 V. Intensive explorations further manifest that the modified mechanism of dual-ion doping strategy is attributed to the synergistic coupling effect of a substantial change in Na occupancy distribution and an increase in oxygen vacancy buffer. Thus, the optimized cathode expedites Na + diffusion and reduces detrimental phase transformation, which favors high-rate performance and long-term cycling stability. This study develops a route to rationally design high-voltage cathode materials for SIBs.

25 ENERGY STORAGE↗
DOE OSTI2026

Topological Hall Effect in Antiferromagnetic Co-Doped Fe 3 GaTe 2

Fe 3 GaTe 2 is van der Waals (vdW) ferromagnet with a Curie temperature T C ranging from 350 K to 380 K, followed upon cooling by a ferrimagnetic transition near room temperature. Substituting Fe with Co was previously reported to induce antiferromagnetism (AFM) at a Co fraction dependent Néel temperature TN. In this work, we confirm the overall phase diagram of the Fe 3-x Co x GaTe 2 series as a function of x and temperature via magnetization and electrical transport measurements. For x ≥ 0.6 the Hall effect is observed to mimic the magnetization as the AF ground state is suppressed by the external magnetic field via a metamagnetic transition, thus displaying an anomalous Hall response. At low temperatures, we also observe a pronounced topological Hall signal peaking at μ 0 H = 4 T, or within the metamagnetic transition region of fields. This observation points to the presence of magnetic field-induced chiral spin textures, such as skyrmions upon approaching magnetization saturation. Remarkably, magnetic force microscopy (MFM) reveals the emergence of nearly circular magnetic domains, with diameters on the order of 100–200 nm, within the antiferromagnetic phase. Here, a detailed analysis of the MFM images indicates that the topological Hall effect is closely linked to the field-induced stabilization of magnetic domain structures, likely exhibiting chiral textures. This observation suggests the possible formation of skyrmions already in the AFM phase, i.e., AFM skyrmions, that evolve into ferromagnetic (FM) ones upon increasing the magnetic field. Consequently, Co-doped Fe 3 GaTe 2 might provide a platform to investigate the transformation of skyrmions, initially coupled antiferromagnetically into ferromagnetic skyrmions, and to explore its impact on the topological and skyrmion Hall effects.

anomalous Hall effect↗
DOE OSTI2022

Molecular structure and catalytic promotional effect of Mn on supported Na 2 WO 4 /SiO 2 catalysts for oxidative coupling of methane (OCM) reaction

The structure and promotional effect of Mn in supported Mn-Na 2 WO 4 /SiO 2 catalysts for the oxidative coupling of methane (OCM) reaction has been debated for a longtime in the literature. In the current investigation, with the aid of multiple in-situ characterization studies, we show that the freshly calcined supported 1.2Mn-5Na 2 WO 4 /SiO 2 catalyst possesses crystalline Na 2 WO 4 , Mn 2 O 3 and SiO 2 (cristobalite phase) along with surface MnO x and Na-WO x sites at low temperature and oxidizing environments. Under the OCM reaction environment (T>800°C), the crystalline Na 2 WO 4 phase melts and Mn 2 O 3 phase reduces. In contrast, the surface MnO x and Na-WO x sites exhibit excellent thermal and chemical stability. Exposure of the 1.2Mn-5Na 2 WO 4 /SiO 2 catalyst to the OCM reaction environment redisperses the molten Na 2 WO 4 phase on the SiO 2 support to form new surface WO x sites. Interestingly, the stable MnO x species interacts with both molten Na 2 WO 4 phase and surface Na-WO x sites during OCM reaction. Controlled transient kinetic experiments in TAP and detailed steady state OCM fixed-bed reaction studies reveal the role and promotional effect of Mn in the 1.2Mn-5Na 2 WO 4 /SiO 2 catalyst. The W-oxides (both molten Na 2 WO 4 and surface Na-WO x sites) are the active sites for the catalytic OCM reaction and the MnO x species only function as promoters. The promotion of MnO x strongly depends on the gas phase O 2 partial pressure and the MnO x species act as mediators for oxygen exchange between the gas phase molecular O 2 and catalyst lattice oxygen. In conclusion, the temperature dependent MnO x promotion reveals that the MnO x species selectively promote the molten Na 2 WO 4 phase at lower reaction temperature and the surface Na-WO x sites at higher temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding Selectivity in CO2 Hydrogenation to Methanol for MoP Nanoparticle Catalysts Using In Situ Techniques

Molybdenum phosphide (MoP) catalyzes the hydrogenation of CO, CO2, and their mixtures to methanol, and it is investigated as a high-activity catalyst that overcomes deactivation issues (e.g., formate poisoning) faced by conventional transition metal catalysts. MoP as a new catalyst for hydrogenating CO2 to methanol is particularly appealing for the use of CO2 as chemical feedstock. Herein, we use a colloidal synthesis technique that connects the presence of MoP to the formation of methanol from CO2, regardless of the support being used. By conducting a systematic support study, we see that zirconia (ZrO2) has the striking ability to shift the selectivity towards methanol by increasing the rate of methanol conversion by two orders of magnitude compared to other supports, at a CO2 conversion of 1.4% and methanol selectivity of 55.4%. In situ X-ray Absorption Spectroscopy (XAS) and in situ X-ray Diffraction (XRD) indicate that under reaction conditions the catalyst is pure MoP in a partially crystalline phase. Results from Diffuse Reflectance Infrared Fourier Transform Spectroscopy coupled with Temperature Programmed Surface Reaction (DRIFTS-TPSR) point towards a highly reactive monodentate formate intermediate stabilized by the strong interaction of MoP and ZrO2. This study definitively shows that the presence of a MoP phase leads to methanol formation from CO2, regardless of support and that the formate intermediate on MoP governs methanol formation rate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Fictitious phase separation in Li layered oxides driven by electro-autocatalysis

Layered oxides widely used as lithium-ion battery electrodes are designed to be cycled under conditions that avoid phase transitions. Although the desired single-phase composition ranges are well established near equilibrium, operando diffraction studies on many-particle porous electrodes have suggested phase separation during delithiation. Notably, the separation is not always observed, and never during lithiation. These anomalies have been attributed to irreversible processes during the first delithiation or reversible concentration-dependent diffusion. However, these explanations are not consistent with all experimental observations such as rate and path dependencies and particle-by-particle lithium concentration changes. Here, we show that the apparent phase separation is a dynamical artefact occurring in a many-particle system driven by autocatalytic electrochemical reactions, that is, an interfacial exchange current that increases with the extent of delithiation. We experimentally validate this population-dynamics model using the single-phase material L ix (Ni 1/3 Mn 1/3 Co 1/3 )O 2 (0.5 < x < 1) and demonstrate generality with other transition-metal compositions. Operando diffraction and nanoscale oxidation-state mapping unambiguously prove that this fictitious phase separation is a repeatable non-equilibrium effect. We quantitatively confirm the theory with multiple-datastream-driven model extraction. More generally, our study experimentally demonstrates the control of ensemble stability by electro-autocatalysis, highlighting the importance of population dynamics in battery electrodes (even non-phase-separating ones).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Transparent Refractory Aerogels for Efficient Spectral Control in High–Temperature Solar Power Generation

Although spectrally selective materials play a key role in existing and emerging solar thermal technologies, temperature-related degradation currently limits their use to below 700 °C in vacuum and even lower temperatures in air. Here a solar-transparent refractory aerogel that offers stable performance up to 800 °C in air is demonstrated, which is significantly greater than its silica counterpart. This improved stability is attributed to the formation of a refractory aluminum silicate phase, which is synthesized using a conformal single cycle of atomic layer deposition within the high-aspect-ratio pores of silica aerogels. Furthermore, based on direct heat loss measurements, the transparent refractory aerogel achieves a receiver efficiency of 75% at 100 suns and an absorber temperature of 700 °C, which is a 5% improvement over the state of the art. Transparent refractory aerogels may find widespread applicability in solar thermal technologies by enabling the use of lower-cost optical focusing systems and eliminating the need for highly evacuated receivers. In particular, a shift to higher operating temperatures while maintaining a high receiver efficiency can enable the use of advanced supercritical CO 2 power cycles and ultimately translate to an ≈10% (absolute) improvement in solar-to-electrical conversion efficiency relative to existing linear concentrating systems.

14 SOLAR ENERGY↗
DOE OSTI2024

Self‐Templated 3D Sulfide‐Based Solid Composite Electrolyte for Solid‐State Sodium Metal Batteries

Abstract Rechargeable solid‐state sodium metal batteries (SSMBs) experience growing attention owing to the increased energy density (vs Na‐ion batteries) and cost‐effective materials. Inorganic sulfide‐based Na‐ion conductors also possess significant potential as promising solid electrolytes (SEs) in SSMBs. Nevertheless, due to the highly reactive Na metal, poor interface compatibility is the biggest obstacle for inorganic sulfide solid electrolytes such as Na 3 SbS 4 to achieve high performance in SSMBs. To address such electrochemical instability at the interface, new design of sulfide SE nanostructures and interface engineering are highly essential. In this work, a facile and straightforward approach is reported to prepare 3D sulfide‐based solid composite electrolytes (SCEs), which utilize porous Na 3 SbS 4 (NSS) as a self‐templated framework and fill with a phase transition polymer. The 3D structured SCEs display obviously improved interface stability toward Na metal than pristine sulfide. The assembled SSMBs (with TiS 2 or FeS 2 as cathodes) deliver outstanding electrochemical cycling performance. Moreover, the cycling of high‐voltage oxide cathode Na 0.67 Ni 0.33 Mn 0.67 O 2 (NNMO) is also demonstrated in SSMBs using 3D sulfide‐based SCEs. This study presents a novel design on the self‐templated nanostructure of SCEs, paving the way for the advancement of high‐energy sodium metal batteries.

Guo, Xiaolin↗
DOE OSTI2021

Local molecular environment drives speciation and reactivity of ion complexes in concentrated salt solution

The speciation and reactivity of aqueous salt solutions are important for a wide variety of applications. However, application of this information is inhibited by broad disagreement about composition, mechanisms, and structure in concentrated solutions especially. Here, neutron diffraction with isotopic substitution measurements on aqueous zinc chloride solutions are used to calibrate molecular dynamics simulations that include effective electronic polarization. This allows us to probe the origin of speciation and reactivity of zinc chloride-water ion complexes, ZnCl x (H 2 O) y 2-x (x ≤ 4 and y ≤ 6), by comparing the reactivity of species in concentrated (4.5 m) and dilute (0.01 m) conditions. Within the concentrated solution, it is found that the extended solvation environment is dominated by solvent-separated ion complexes whose presence increases the free energy of activation for interconversion of species while simultaneously enhancing their thermodynamic stability. This concentration-dependent reactivity and stability suggests that other reactions, such as the nucleation of solid phases, will also be affected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Metasurface holographic optical traps for ultracold atoms

We propose metasurface holograms as a novel platform to generate optical trap arrays for cold atoms with high quality, efficiency, and thermal stability. We developed design and fabrication methods to create dielectric, phase-only metasurface holograms based on titanium dioxide. We experimentally demonstrated optical trap arrays of various geometries, including periodic and aperiodic configurations with dimensions ranging from 1D to 3D and up to a few hundred trap sites. We characterized the performance of the holographic metasurfaces in terms of the positioning accuracy, size and intensity uniformity of the generated traps, and power handling capability of the dielectric metasurfaces. Our proposed platform has great potential for enabling fundamental studies of quantum many-body physics, and quantum simulation and computation tasks. The compact form factor, passive nature, good power handling capability, and scalability of generating high-quality, large-scale arrays also make the metasurface platform uniquely suitable for realizing field-deployable devices and systems based on cold atoms.

42 ENGINEERING↗
DOE OSTI2024

Effects of Nonequilibrium Atomic Structure on Ionic Diffusivity in LLZO: A Classical and Machine Learning Molecular Dynamics Study

To improve the performance of electrochemical devices, it is essential to understand the effects of nonequilibrium motifs in solids, such as grain boundaries, amorphous phases, and highly strained regions, on atomic-scale transport and stability. Molecular dynamics simulations are used to explore the combined effect of far-from-equilibrium atomic structures and the choice of interatomic potential on ionic diffusivity predictions for Li 7 La 3 Zr 2 O 12 (LLZO), a promising solid electrolyte for all-solid-state batteries. Amorphization and high strain are considered using both classical Buckingham interatomic potentials and machine learning force fields. Here we find that both crystalline expansion and amorphization tend to slow diffusion, although the different physical encodings in the two potentials impact the properties in different ways. We trace these variations to a combination of structural and transport factors, the contributions of which are deconvoluted computationally. Graph-based analysis reveals that the variations for amorphous LLZO arise from the connectivity of diffusion pathways within the predicted structures, which generally correlates with diffusivity and is notably higher for structures generated by the machine learning force fields. Our study provides additional insight into the relationship between atomic structure and diffusivity in LLZO, while also highlighting the need for care in choosing and validating potentials to simulate far from equilibrium structures.

25 ENERGY STORAGE↗
DOE OSTI2026

The Hidden Path to the Resonance-Stabilized Fulvenallenyl Radical (C 7 H 5 ) via the Bimolecular Reaction of Tricarbon (C 3 , X 1 Σ g + ) with 1,3-Butadiene (C 4 H 6 ; X 1 A g )

Here, we report a novel bimolecular reaction pathway forming the resonance-stabilized fulvenallenyl radical (C 7 H 5 ) via the gas-phase reaction of tricarbon (C 3 , X 1 Σ g + ) with 1,3-butadiene (C 4 H 6 , X 1 A g ). Crossed molecular beam experiments combined with high-level electronic structures and statistical calculations reveal a rich potential energy surface. The reaction proceeds via tricarbon addition to a double bond of 1,3-butadiene, overcoming a 30 kJ mol –1 barrier, followed by ring closure, isomerizations (ring opening/closures, hydrogen shifts), and eventual hydrogen atom loss, yielding the fulvenallenyl radical (p1) almost exclusively via two dominant pathways. Considering the entrance barrier, this reaction may occur in high-temperature environments, like circumstellar envelopes of carbon stars, but is suppressed in colder regions such as molecular clouds and Titan’s atmosphere. These findings highlight the unexpected reactivity of small carbon clusters in shaping the molecular complexity of our universe, from the flicker of a flame to the death of a star.

Aromatic compounds↗
DOE OSTI2023

Operation of Layered LiCoO 2 to Higher Voltages with a Localized Saturated Electrolyte

The commercialization of lithium-ion batteries started with the layered LiCoO 2 (LCO) cathode for portable electronics, but only 50% of its theoretical capacity can be used in practical cells due to detrimental surface and bulk degradations when charged to high voltages. Here we demonstrate here that the stability of electrolyte plays a critical role in the performance of LCO at high voltages by employing a localized saturated electrolyte (LSE). With a cutoff voltage of 4.5 V, LCO achieves an initial 1C discharge capacity of 176 mA h g -1 and a capacity retention of 80% over 230 cycles. Even with a cutoff voltage of 4.6 V, LCO with 2% aluminum doping displays an initial discharge capacity of 189 mA h g -1 at 1C rate with 80% capacity retention over 137 cycles. With extensive analytical characterization, we show that the improved cycling stability stems from a suppression of the O3 to H1-3 phase transition as well as a robust inorganic-rich cathode-electrolyte interphase (CEI) facilitated by the LSE. This work highlights the importance of protecting the surface as well as the bulk with appropriate electrolytes for the high-voltage, higher-energy-density operation of LCO.

25 ENERGY STORAGE↗
DOE OSTI2026

Cyclodextrin-Derived Porous Liquids Enabled by In Situ Solvation Shell Formation

Porous liquids (PLs) represent a unique platform for molecular separations by combining permanent porosity with liquid-phase mobility. However, it remains a formidable challenge to construct and stabilize PLs with sub-5 Å pores using readily available porous host and liquid media. Here, we report the construction of cyclodextrin (CD)-derived PLs enabled by in situ solvation shell formation. The acid–base neutralization reaction between CD and an organic base was leveraged to generate a thin ionic solvation shell around the CD host, effectively liquefying CD and preventing its segregation in the liquid base medium while preserving accessible molecular-scale cavities. Spectroscopic analysis, neutron scattering, density functional theory calculations, and molecular dynamics simulations collectively confirm the structural evolution and existence of abundant internal porosity in PLs. The unique architectures of CD-derived PLs enable highly selective encapsulation of fluorinated alkanes and significantly enhanced uptake of inert gases. This facile and generalizable strategy enables construction of high-quality PLs with engineered ultramicroporosity to facilitate molecular separations.

Cavities↗
DOE OSTI2022

Experimental realization of one dimensional helium

As the spatial dimension is lowered, locally stabilizing interactions are reduced, leading to the emergence of strongly fluctuating phases of matter without classical analogues. Here we report on the experimental observation of a one dimensional quantum liquid of 4 He using nanoengineering by confining it within a porous material preplated with a noble gas to enhance dimensional reduction. The resulting excitations of the confined 4 He are qualitatively different than bulk superfluid helium, and can be analyzed in terms of a mobile impurity allowing for the characterization of the emergent quantum liquid beyond the Luttinger liquid paradigm. The low dimensional helium system offers the possibility of tuning via pressure—from weakly interacting, all the way to the super Tonks-Girardeau gas of strongly interacting hard-core particles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electromagnetic signatures of a chiral quantum spin liquid

Quantum spin liquids (QSL) have emerged as a captivating subject within interacting spin systems that exhibit no magnetic ordering even at the lowest temperature accessible experimentally. However, definitive experimental evidence remains elusive. In light of the recent surge in theoretical and experimental interest in the half-filled Hubbard model on a triangular lattice, which offers the potential for stabilizing a chiral QSL, we investigate the electromagnetic signatures of this phase to facilitate experimental detection. Utilizing a combination of parton mean-field theory and unbiased density-matrix renormalization group calculations, we systematically examine the electrical charge and orbital electrical current associated with a spinon excitation in the chiral QSL. Additionally, we calculate the longitudinal and transverse optical conductivities below the Mott gap. Furthermore, employing quantum field theory analysis, we unravel the connection between spinon excitations and emergent as well as physical gauge fields. Our results demonstrate that the chiral QSL phase exhibits a distinct electromagnetic response, even within a Mott insulator regime. This finding holds great potential for enabling the experimental detection of this long-sought-after phase.

36 MATERIALS SCIENCE↗