Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model scaling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Advanced Turbulence Models for Large-Scale Atmospheric Boundary Layer Flows

We present high-fidelity large-eddy-simulation (LES) modeling approaches for the turbulent atmospheric boundary layer (ABL) flows. Wind energy is a prime example of an application driven by ABL. Generation of electrical energy from farms of wind turbines at night in the stable ABL is a particularly interesting situation. In this report, we consider the well-known GEWEX (Global Energy and Water Cycle Experiment) Atmospheric Boundary Layer Study (GABLS) stably stratified benchmark LES case. We use a high-order spectral element code Nek5000/RS, which is supported under the DOE's Exascale Computing Project (ECP) Center for Efficient Exascale Discretizations (CEED) project, targeting application simulations on various acceleration-device based exascale computing platforms. In our earlier ANL report, we demonstrated our newly developed subgrid-scale (SGS) models based on high-pass filter (HPF), mean-field eddy viscosity (MFEV), and Smagorinsky (SMG) with no-slip and traction boundary conditions, provided with low-order statistics, convergence and turbulent structure analysis. In this report, we extend the range of our SGS modeling approaches in the context of the mean-field eddy viscosity (MFEV), to include the solution of an SGS turbulent kinetic energy equation (TKE). We demonstrate the model fidelity of Nek5000/RS in comparison to that of AMR-Wind, a block-structured second-order finite-volume code with adaptive-mesh-refinement capabilities, with which we studied scaling performance for both codes in comparison on DOE's leadership computing platforms.

17 WIND ENERGY↗
NASA NTRS1992

Scale effects in the response and failure of fiber reinforced composite laminates loaded in tension and in flexure

The feasibility of using scale model testing for predicting the full-scale behavior of flat composite coupons loaded in tension and beam-columns loaded in flexure is examined. Classical laws of similitude are applied to fabricate and test replica model specimens to identify scaling effects in the load response, strength, and mode of failure. Experiments were performed on graphite-epoxy composite specimens having different laminate stacking sequences and a range of scaled sizes. From the experiments it was deduced that the elastic response of scaled composite specimens was independent of size. However, a significant scale effect in strength was observed. In addition, a transition in failure mode was observed among scaled specimens of certain laminate stacking sequences. A Weibull statistical model and a fracture mechanics based model were applied to predict the strength scale effect since standard failure criteria cannot account for the influence of absolute specimen size on strength.

Jackson, Karen E.↗
NASA NTRS2012

Evaluation of Icing Scaling on Swept NACA 0012 Airfoil Models

Icing scaling tests in the NASA Glenn Icing Research Tunnel (IRT) were performed on swept wing models using existing recommended scaling methods that were originally developed for straight wing. Some needed modifications on the stagnation-point local collection efficiency (i.e., beta(sub 0) calculation and the corresponding convective heat transfer coefficient for swept NACA 0012 airfoil models have been studied and reported in 2009, and the correlations will be used in the current study. The reference tests used a 91.4-cm chord, 152.4-cm span, adjustable sweep airfoil model of NACA 0012 profile at velocities of 100 and 150 knot and MVD of 44 and 93 mm. Scale-to-reference model size ratio was 1:2.4. All tests were conducted at 0deg angle of attack (AoA) and 45deg sweep angle. Ice shape comparison results were presented for stagnation-point freezing fractions in the range of 0.4 to 1.0. Preliminary results showed that good scaling was achieved for the conditions test by using the modified scaling methods developed for swept wing icing.

Tsao, Jen-Ching↗
NASA NTRS1993

Structural similitude and design of scaled down laminated models

The excellent mechanical properties of laminated composite structures make them prime candidates for wide variety of applications in aerospace, mechanical and other branches of engineering. The enormous design flexibility of advanced composites is obtained at the cost of large number of design parameters. Due to complexity of the systems and lack of complete design based informations, designers tend to be conservative in their design. Furthermore, any new design is extensively evaluated experimentally until it achieves the necessary reliability, performance and safety. However, the experimental evaluation of composite structures are costly and time consuming. Consequently, it is extremely useful if a full-scale structure can be replaced by a similar scaled-down model which is much easier to work with. Furthermore, a dramatic reduction in cost and time can be achieved, if available experimental data of a specific structure can be used to predict the behavior of a group of similar systems. This study investigates problems associated with the design of scaled models. Such study is important since it provides the necessary scaling laws, and the factors which affect the accuracy of the scale models. Similitude theory is employed to develop the necessary similarity conditions (scaling laws). Scaling laws provide relationship between a full-scale structure and its scale model, and can be used to extrapolate the experimental data of a small, inexpensive, and testable model into design information for a large prototype. Due to large number of design parameters, the identification of the principal scaling laws by conventional method (dimensional analysis) is tedious. Similitude theory based on governing equations of the structural system is more direct and simpler in execution. The difficulty of making completely similar scale models often leads to accept certain type of distortion from exact duplication of the prototype (partial similarity). Both complete and partial similarity are discussed. The procedure consists of systematically observing the effect of each parameter and corresponding scaling laws. Then acceptable intervals and limitations for these parameters and scaling laws are discussed. In each case, a set of valid scaling factors and corresponding response scaling laws that accurately predict the response of prototypes from experimental models is introduced. The examples used include rectangular laminated plates under destabilizing loads, applied individually, vibrational characteristics of same plates, as well as cylindrical bending of beam-plates.

Simitses, G. J.↗
NASA NTRS1975

Automated parking garage system model

A one-twenty-fifth scale model of the key components of an automated parking garage system is described. The design of the model required transferring a vehicle from an entry level, vertically (+Z, -Z), to a storage location at any one of four storage positions (+X, -X, +Y, +Y, -Y) on the storage levels. There are three primary subsystems: (1) a screw jack to provide the vertical motion of the elevator, (2) a cam-driven track-switching device to provide X to Y motion, and (3) a transfer cart to provide horizontal travel and a small amount to vertical motion for transfer to the storage location. Motive power is provided by dc permanent magnet gear motors, one each for the elevator and track switching device and two for the transfer cart drive system (one driving the cart horizontally and the other providing the vertical transfer). The control system, through the use of a microprocessor, provides complete automation through a feedback system which utilizes sensing devices.

Collins, E. R., Jr.↗
NASA NTRS1980

Shape change of Galileo probe models in free-flight tests

Scale models of the Galileo Probe made of polycarbonate, AXF5Q graphite, carbon-carbon composite, and carbon-phenolic were flown in a free flight range in an ambient gas of air, krypton, or xenon. Mach numbers varied between 14 and 24, Reynolds numbers between 300,000 and 1,000,000, stagnation pressures between 31 and 200 atm, and stagnation point heat transfer rates between 10 and 1,000 kW/sq cm. Shadowgraphs indicate gouging ablation of the aft portion of the frustum; the gouging was moderate in air and severe in the noble gases. The graphite models break in the same region. An explanation of the phenomena is offered in terms of the strong compression and shear caused by the reattachment of a turbulent separated flow. Conditions are calculated for similar tests appropriate for Von Karman Facility of the Arnold Engineering Development Center in which a larger model can be flown in argon.

Park, C.↗
NASA NTRS1964

Thermal similitude studies

Thermal scale modeling for space vehicles - thermally similar model derived from mathematical model of prototype

SCALE MODEL↗
DOE OSTI2023

Modeling and Simulation of Xe-100-type Pebble Bed Gas-Cooled Reactor with SCALE

The US Department of Energy (DOE) announced the Advanced Reactor Demonstration Program (ARDP) to accelerate the deployment of advanced reactor concepts. Awardees of ARDP funds are expected to demonstrate the operation of an advanced reactor within 7 years of receiving the award. X-Energy’s advanced reactor concept, the Xe-100, was selected as one of two advanced reactor concepts to receive funding to demonstrate the operation of its high-temperature gas-cooled pebble-bed reactor before the end of this decade. As a result of this push to bring advanced reactors to maturation and commercialization, transition and deployment scenario studies are being performed under the Systems Analysis and Integration (SA&I) campaign within the DOE Office of Nuclear Energy (DOE-NE) to evaluate the transition of the current US commercial fleet of light-water reactors (LWRs) to a future fleet of advanced reactors consisting of a mix of ARDP type reactor concepts and advanced LWRs. To accurately evaluate the front- and back-end resource requirements, it is important to perform reactor physics calculations to determine the discharge burnup and isotopic content, fuel residence time, as well as other parameters. For this purpose, a summer project funded by the SA&I campaign allowed for the setup of SCALE models for full-core Xe-100 type high-temperature gas-cooled pebble-bed reactor and a Xe-100 type slice using publicly available information. The core-averaged equilibrium compositions and zone-wise equilibrium compositions for the slice and 3D models, respectively, were obtained following an iterative depletion method developed by Bostelmann et al. using SCALE’s reactor physics sequence TRITON. The slice model was used with TRITON to generate burnup-dependent cross section libraries at different temperatures which can be used with SCALE’s ORIGAMI code to rapidly determine fuel inventory and therefore to perform quick sensitivity studies on parameters such as the pebble location in the core. The SCALE/TRITON transport and depletion calculation for the Xe-100 type slice model indicates that the isotopic concentrations are in good agreement at 1,300 effective full power days (EFPD) for 235 U. An analysis of 236 U results match 239 Pu results would seem to indicate a typographical error in Mulder and Boyes wherein the reported results of 236 U and 239 Pu are reversed. In addition to SCALE/TRITON calculations, a new capability within SCALE/ORIGAMI for the simulation of pebble-bed reactors was used to study the burnup sensitivity with respect to the pebble pathway through the core. The SCALE/ORIGAMI results show that pebbles that travel closer to the reflector for the entire depletion history have a higher burnup than pebbles that travel through the middle of the core because of the higher thermal to fast flux ratio near the reflector. Consequently, a pebble’s burnup is strongly affected by the pebble’s pathway for each pass. Additional phenomena such as temperature distributions in the core and different travel times of the pebbles in the individual radial zones further affect the burnup distribution. The sensitivity of the discharge vector to the pebble pathways taken during each pass can be evaluated in the future using SCALE/ORIGAMI now that the SCALE inputs have been established.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1977

Over-the-wing model thrust reverser noise tests

Static acoustic tests were conducted on a 1/12 scale model over-the-wing target type thrust reverser. The model configuration simulates a design that is applicable to the over-the-wing short-haul advanced technology engine. Aerodynamic screening tests of a variety of reverser designs identified configurations that satisfied a reverse thrust requirement of 35 percent of forward thrust at a nozzle pressure ratio of 1.29. The variations in the reverser configuration included, blocker door angle, blocker door lip angle and shape, and side skirt shape. Acoustic data are presented and compared for the various configurations. The model data scaled to a single full size engine show that peak free field perceived noise (PN) levels at a 152.4 meter sideline distance range from 98 to 104 PNdb.

Goodykoontz, J.↗
NASA NTRS2010

A Methodology for Mapping Launch Vehicle Buffet Loads

Buffet loads represent the primary source of high frequency loading for launch vehicles during the ascent portion of flight. Currently, experimental techniques establish the nature of buffeting using a rigid scale model of the vehicle. The buffet forcing functions resulting from such tests are then applied to reduced finite-element models of the full-scale vehicle to determine the response and consequent loading. This paper discusses the techniques required to translate model-derived, empirical buffet forcing functions into responses for the full-scale launch vehicle, as used to determine the buffet loading for NASA's Ares I launch vehicle.

Schwarz, Jordan B.↗
NASA NTRSDate not supplied

Wind Tunnel to Full Scale Mapping of Winds and Loads for Launch-Vehicle Ground Wind Loads

A launch vehicle ground-wind-loads program was conducted at the NASA Langley Transonic Dynamics Tunnel. The objectives were to quantify key aerodynamic and structural characteristics that impact the occurrence of large wind-induced oscillations of a launch vehicle when exposed to ground winds prior to launch. Of particular interest is the dynamic response of a launch vehicle when a von Kármán vortex street forms in the wake of the vehicle resulting in quasiperiodic lift and drag forces.Vehicle response to these quasiperiodic forces can become quite large when the frequency of vortex shedding nears that of a lowly-damped structural mode thereby exciting a resonant response. The study of ground-wind-loads presents unique challenges to quantify significant characteristics of the approaching wind and to relate the wind-tunnel acquired static, dynamic, and gravitational loads to full-scale vehicles. This paper will explain the correlation process between model-scale and full-scale wind characteristics and resulting structural loads. Characterization of the wind at a launch site requires knowledge of the vehicle dynamics and the anemometer performance. Vehicle dynamics dictate the frequency range of interest in characterization of the atmospheric turbulence, and in defining the required data window-length to model dynamic oscillation build-up during wind-gust analysis. Knowledge of the anemometer performance is required to infer peak wind magnitudes since most anemometers cannot directly measure instantaneous peak values. Following proper wind-speed correlation, static and dynamic wind-tunnel loads must be converted to full-scale equivalent values to derive design and operational guidance. In addition to the direct computation of full-scale equivalent loads using relevant scaling parameters, the corrections applied to dynamic loads accounting for differences in structural damping will also be discussed. Furthermore, a phenomenon that manifests in many slender and flexible launch vehicles is a load magnification due to gravity resulting from mass offset under deflection. A method for scaling this contribution from model-scale to full-scale is presented. Finally, a comparison of wind-tunnel derived loads using the described methodologies to launch vehicle measured loads is presented.

ground wind loads↗
NASA NTRSDate not supplied

Wind-Tunnel to Full-Scale Mapping of Winds and Loads for Launch-Vehicle Ground Wind Loads

A launch vehicle ground-wind-loads program was conducted at the NASA Langley Transonic Dynamics Tunnel. The objectives were to quantify key aerodynamic and structural characteristics that impact the occurrence of large wind-induced oscillations of a launch vehicle when exposed to ground winds prior to launch. Of particular interest is the dynamic response of a launch vehicle when a von Kármán vortex street forms in the wake of the vehicle resulting in quasiperiodic lift and drag forces. Vehicle response to these quasiperiodic forces can become quite large when the frequency of vortex shedding nears that of a lowly-damped structural mode thereby exciting a resonant response. The study of ground-wind-loads presents unique challenges to quantify significant characteristics of the approaching wind and to relate the wind-tunnel acquired static, dynamic, and gravitational loads to full-scale vehicles. This paper will explain the correlation process between model-scale and full-scale wind characteristics and resulting structural loads. Characterization of the wind at a launch site requires knowledge of the vehicle dynamics and the anemometer performance. Vehicle dynamics dictate the frequency range of interest in characterization of the atmospheric turbulence, and in defining the required data window-length to model dynamic oscillation build-up during wind-gust analysis. Knowledge of the anemometer performance is required to infer peak wind magnitudes since most anemometers cannot directly measure instantaneous peak values. Following proper wind-speed correlation, static and dynamic wind-tunnel loads must be converted to full-scale equivalent values to derive design and operational guidance. In addition to the direct computation of full-scale equivalent loads using relevant scaling parameters, the corrections applied to dynamic loads accounting for differences in structural damping will also be discussed. Furthermore, a phenomenon that manifests in many slender and flexible launch vehicles is a load magnification due to gravity resulting from mass offset under deflection. A method for scaling this contribution from model-scale to full-scale is presented. Finally, a comparison of wind-tunnel derived loads using the described methodologies to launch vehicle measured loads is presented.

Ground wind loads↗
DOE OSTI2025

Multiscale and Machine Learning Modeling for Process-informed Microstructure Prediction in Additively Manufactured Materials using MALAMUTE

The Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy aims to develop and qualify additively manufactured materials for nuclear applications. One key challenge to this is the microstructural variability observed in the additively manufactured products and their impact on the properties and performance of the material in extreme environments. AMMT is using a combination of high-throughput experimental and modeling techniques to accelerate qualification. Conventionally, in-situ and ex-situ characterizations and testing are performed to correlate different aspects of the additive manufacturing process to the final product and its performance. However, adopting a trial-and-error approach to experimentally evaluate the vast range of process parameters required to capture microstructural variability is cost-prohibitive. Modeling and simulation provide a comparatively inexpensive way to understand and correlate the microstructural evolution to the processing conditions. The modeling and simulation work-packages within the AMMT program aims to use physics-based and machine learning models to develop a digital twin for additive manufacturing that can correlate the process conditions to the final product and establish a process-structure-property-performance (PSPP) correlation. The melting and subsequent solidification that occurs during the additive process is a complex phenomenon that requires multiscale multiphysics analysis. This work package focuses on understanding the role of process variabilities on the unique microstructural characteristics of additively manufactured materials. Microstructural features at the subgrain level, such as compositional micro-heterogeneity and dislocation cells, are of particular interest here since they can influence the creep properties and radiation performance. Idaho National Laboratory’s Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) software, provides an ideal platform for developing the multiphysics multiscale model to explore the intricacies of the microstructural evolution during the AM processes within a single framework. Furthermore, given that such full-fidelity simulations can be computationally intensive, reduced order models are necessary to explore the PSPP space for additively manufactured materials in an efficient, reliable, and cost-effective way. This work focuses on capturing the microstructural variabilities at the subgrain level that are often missing in the part-scale models. In fiscal year 2025, we significantly advanced upon our work in the last fiscal year, in terms of the predictive capabilities of the physics-based and ML models, by adding the capabilities to capture subgrain-level micro-segregation during solidification using phase-field model and to predict the time-dependent dynamics of the AM process through the MOGPAR model. The alloy solidification model in MOOSE incorporates the thermodynamic properties and free energy relevant to 316 stainless steel. The model demonstrates the Cr and Ni segregation that occurs during solidification, including that the rate of solidification. The microstructural evolution model is connected to the process conditions via the surrogate model developed in this work. This enables predictions of the final microstructure in conjunctions with the manufacturing process. This work supports AMMT's rapid qualification goals by laying the foundation for an efficient and cost-effective model establishing the PSPP correlation for AM. The generated microstructures and predicted micro-segregation can be used by other work packages under AMMT to evaluate the properties and environmental response of the material at the mesoscale. Thus, this work helps to identify the key microstructural features at the subgrain level that are significant in property and performance predictions of additively manufactured components. This work will also provide inputs to the large-scale process variability models to reevaluate and validate assumptions and simplifications made in the part-scale models. Furthermore, through active learning this work can help identify the data need from both modeling and experimental sides for development of a robust digital twin for additive manufacturing and accelerate the AMMT's qualification efforts.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Multiscale and Machine Learning Modeling for Process-informed Microstructure Prediction in Additively Manufactured Materials Using MALAMUTE

Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy, aims to develop and qualify additively-manufactured materials for nuclear applications. The key challenges to these efforts are the microstructural variabilities observed on the AM products and their impact on the properties and performance of the material in extreme environments. AMMT is using a combination of high-through-put experimental and modeling techniques to accelerate the qualification efforts. Conventionally, in-situ and ex-situ characterizations and testing are performed to correlate different aspects of the AM process to the final product and its performance. However, adopting a trial-and-error approach to experimentally evaluate the vast range of process parameters required to capture the microstructural variabilities is cost-prohibitive. Modeling and simulation provide a comparatively inexpensive way to understand and correlate the microstructural evolution to the processing conditions. The modeling and simulation work-packages within the AMMT program aims to use physics-based and machine learning modeling capabilities to develop a digital twin for AM that can correlate the process conditions to the final product and establish a process-structure-property-performance (PSPP) correlation for AM materials. The melting and subsequent solidification that occurs during the AM process is a complex phenomenon that requires multiscale multiphysics analysis. Idaho National Laboratory’s (INL) Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) software, provides an ideal platform for developing the multiphysics multiscale model to explore the intricacies of the microstructural evolution during the AM processes within a single framework. Furthermore, given that such full-fidelity simulations can be computationally intensive, reduced order models are necessary to explore the PSPP space for AM materials in an efficient, reliable, and cost-effective way. This work package focuses on understanding the role of process variabilities on the various microstructural characteristics of the AM materials. Microstructures unique to AM materials, such as compositional micro-heterogeneity and dislocation cells, are of particular interest here since they can influence the creep properties and radiation performance. In fiscal year (FY) 24, we significantly advanced upon our work in the last fiscal year, both on physics-based and ML models. The alloy solidification model available in MOOSE has been extended to incorporate the thermodynamic properties and free energy relevant to 316SS. The model demonstrates the Cr segregation that occurs during solidifcation. It is demonstrated that rate of solidification and solute segregation is primarily influence by the cooling rate dictating the level of freezing. This work captures the microstructural variabilities at the subgrain level that are often missing in the part-scale models. With an aim to connect the microstructural evolution model to realistic process conditions, a reduced order model is developed for predicting the thermal conditions around meltpool from high-fidelity process simulations. Furthermore, machine learning approach is used to accelerate the temperature prediction during the AM process. In the following years, MALAMUTE will be used to connect different aspects of the models and quantitatively predict the microstructural evolution. The developed ML-based surrogate model will consider the process conditions as the input to predict the microstructural features in a cost-effective way. The generated microstructures can be used by other work packages under AMMT to evaluate the properties and environmental response of the material at the mesoscale. Thus, this work help identify the key microstructural features at the subgrain level that are significant in property/performance prediction of the AM products. This work will provide inputs to the large-scale process variability models to reevaluate and validate assumptions/simplifications made in the part-scale models. Furthermore, through active learning this work will help identify the data need from both modeling and experimental sides for development of a robust digital twin for AM.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Towards Predictive Plasma Science and Engineering through Revolutionary Multi-Scale Algorithms and Models (Final Report)

This report describes the high-level accomplishments from the Plasma Science and Engineering Grand Challenge LDRD at Sandia National Laboratories. The Laboratory has a need to demonstrate predictive capabilities to model plasma phenomena in order to rapidly accelerate engineering development in several mission areas. The purpose of this Grand Challenge LDRD was to advance the fundamental models, methods, and algorithms along with supporting electrode science foundation to enable a revolutionary shift towards predictive plasma engineering design principles. This project integrated the SNL knowledge base in computer science, plasma physics, materials science, applied mathematics, and relevant application engineering to establish new cross-laboratory collaborations on these topics. As an initial exemplar, this project focused efforts on improving multi-scale modeling capabilities that are utilized to predict the electrical power delivery on large-scale pulsed power accelerators. Specifically, this LDRD was structured into three primary research thrusts that, when integrated, enable complex simulations of these devices: (1) the exploration of multi-scale models describing the desorption of contaminants from pulsed power electrodes, (2) the development of improved algorithms and code technologies to treat the multi-physics phenomena required to predict device performance, and (3) the creation of a rigorous verification and validation infrastructure to evaluate the codes and models across a range of challenge problems. These components were integrated into initial demonstrations of the largest simulations of multi-level vacuum power flow completed to-date, executed on the leading HPC computing machines available in the NNSA complex today. These preliminary studies indicate relevant pulsed power engineering design simulations can now be completed in (of order) several days, a significant improvement over pre-LDRD levels of performance.

42 ENGINEERING↗
NASA NTRS2015

AST Launch Vehicle Acoustics

The liftoff phase induces acoustic loading over a broad frequency range for a launch vehicle. These external acoustic environments are then used in the prediction of internal vibration responses of the vehicle and components which result in the qualification levels. Thus, predicting these liftoff acoustic (LOA) environments is critical to the design requirements of any launch vehicle. If there is a significant amount of uncertainty in the predictions or if acoustic mitigation options must be implemented, a subscale acoustic test is a feasible pre-launch test option to verify the LOA environments. The NASA Space Launch System (SLS) program initiated the Scale Model Acoustic Test (SMAT) to verify the predicted SLS LOA environments and to determine the acoustic reduction with an above deck water sound suppression system. The SMAT was conducted at Marshall Space Flight Center and the test article included a 5% scale SLS vehicle model, tower and Mobile Launcher. Acoustic and pressure data were measured by approximately 250 instruments. The SMAT liftoff acoustic results are presented, findings are discussed and a comparison is shown to the Ares I Scale Model Acoustic Test (ASMAT) results.

Houston, Janice↗