Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high current densities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

STEM characterization of solar cells

Photovoltaic (PV) devices consisting of a thin-film CdTe absorber layer on glass support have long been considered one of the leading technologies for reaching the Department of Energy’s 2030 cost target of less than 0.03/kWh. Here, the currently used device architectures include a thin transparent conductive oxide (TCO) on top of the glass superstrate following by very thin (<100 nm) polycrystalline emitter layer, typically CdS or more recently MgZnO (MZO). The CdTe absorber layer is usually up to 4 µm thick and polycrystalline, followed by the back contact (Figure 1). Typical CdTe thin-film layers are formed from rapid deposition techniques, such as close-spaced sublimation (CSS) or high-rate vapor-transport deposition (HRVDT). Both processes result in a polycrystalline CdTe photo-absorbing film, and such devices can be manufactured cheaply and efficiently at large scale. Record cell efficiencies as high as 22.1% have been demonstrated. However, such cell performances are still far from the theoretical limits (~30% for CdTe), and improvements have mostly been due to better light collection, rather than improvements in absorber conversion efficiency. The remaining obstacles to further improving these devices toward their theoretical limits concern improvements in the fill factor (FF) and, more importantly, open-circuit voltage (V oc ), which is still far from its limit. In fact, it is widely accepted that V oc is the limiting factor since it reaches only about 60% of the CdTe bandgap. This is in contrast to GaAs solar cells, which have reached a V oc of 80% of the bandgap. The reasons for this discrepancy have been identified as the low p -type doping concentrations of CdTe due to the formation of compensating defect states, a poor p-n junction, and the need for better backside ohmic contacts. High interfacial defect density at grain boundaries (GBs) and intragrain dislocations is also one of the main concerns because they contribute to the dark current. This is supported by the study of single-crystal-based CdTe solar cells that were able to reach Voc in excess of 1 V.

14 SOLAR ENERGY↗
DOE OSTI2022

Dense hydrogen layers for high performance MagLIF

We report that Magnetized Liner Inertial Fusion (MagLIF) experiments driven by the Z machine produce >10 13 deuterium-deuterium fusion reactions. Simulations indicate high yields and gains (1000) with increased current and deuterium-tritium layers for burn propagation. Such a coating also isolates the metal liner from the gaseous fuel, which should reduce mixing of liner material into the fuel. However, the vapor density at the triple point is only 0.3 kg/m3, which is not high enough for MagLIF operation. We present two solutions to this problem. First, a fuel wetted low-density plastic foam can be used to form a layer on the inside of the liner. The desired vapor density can be obtained by controlling the temperature. This does however introduce carbon into the layer which will enhance radiation losses. Simulations indicate that this wetted foam layer can significantly contribute to the fusion yield when the foam density is less than 35 kg/m 3 . Second, we show that a pure frozen fuel layer can first be formed on the inside of the liner and then low temperature gaseous fuel can be introduced just before the implosion without melting a significant amount of the ice layer. This approach is the most promising for MagLIF to produce high yield and gain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1981

Electron reflection and secondary emission characteristics of sputter-textured pyrolytic graphite surfaces

Measurements are presented of secondary electron emission and reflected primary electron characteristics of sputter-textured pyrolitic graphite surfaces with microstructures of various sizes and densities, made with an Auger cylindrical mirror analyzer in a high-vacuum chamber at pressures below 1.33 x 10 to the -7th N/sq m (10 to the -9th torr). A dense, tall, thin, spire-like microstructure, obtained at ion energies of 1000 eV and ion current densities of 5 mA/sq cm, is the most effective. The secondary electron emission from such a surface is lower than that of soot, whose secondary emission is among the lowest of any material. At a primary electron energy of 1000 eV, the secondary electron emission yield of smooth CU is about 350% greater than the lowest value obtained for sputter-textured pyrolitic graphite. The reflected primary electron index of smooth Cu is a factor of 80 greater. If the secondary electron emission yield is reduced to 0.3, which is possible with sputter-textured pyrolitic graphite, the traveling wave tube collector efficiency could be improved by as much as 4% over that for smooth copper.

Wintucky, E. G.↗
NASA NTRS1996

High Energy Density Matter for Rocket Propulsion

The objective of the High Energy Density Matter (HEDM) program is to identify, develop, and exploit high energy atomic and molecular systems as energetic sources for rocket propulsion applications. It is a high risk, high payoff program that incorporates both basic and applied research, experimental and theoretical efforts, and science and engineering efforts. The HEDM program is co-sponsored by the Air Force Office of Scientific Research (AFOSR) and the Phillips Laboratory (PURKS). It includes both in-house and contracted University/Industry efforts. Technology developed by the HEDM program offers the opportunity for significant breakthroughs in propulsion system capabilities over the current state-of-the-art. One area of great interest is the use of cryogenic solids to increase the density of the propellant and to act as a stable matrix for storage of energetic materials. No cryogenic solid propellant has ever been used in a rocket, and there remain engineering challenges to such a propellant. However, these solids would enable a wide class of highly energetic materials by providing an environment that is at very low temperatures and is a physical barrier to recombination or energy loss reactions. Previous to our experiments only hydrogen atoms had been isolated in solid hydrogen. To date we have succeeded in trapping B, Al, Li, N, and Mg atoms in solid H2. Small molecules, such as B2 and LiB, are also of interest. Current efforts involve the search for new energetic small molecules, increasing free radical concentrations up to 5 mole percent, and scale-up for propulsion testing.

Carrick, Patrick G.↗
DOE OSTI2023

Stable Cycling with Intimate Contacts Enabled by Crystallinity–Controlled PTFE–Based Solvent–Free Cathodes in All–Solid–State Batteries

All-solid-state batteries (ASSBs) employing Li-metal anodes and inorganic solid electrolytes are attracting great attention due to high safety and energy density for next-generation energy storage devices. However, the volume change of cathode active materials can cause contact loss, resulting in charge carrier isolation, heterogeneous current distribution, and poor electrochemical properties in ASSBs. Here, a simple, yet effective, solvent-free electrode engineering approach with polytetrafluoroethylene (PTFE) as a binder for ASSBs is reported, enabling intimate contact and stable interfaces with the cathode. It is substantiated that the crystallinity of PTFE can be controlled depending on the heat history, and highly crystalline PTFE displays robust mechanical properties. High-nickel LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode prepared with crystalline PTFE show improved cycle and rate performances in ASSBs. In addition, it is revealed that the intimate contact between cathode particles with a stable cathode electrolyte layer is maintained during cycling by postmortem studies. Furthermore, this simple engineering method can be applied to prepare cathodes with a variety of active materials and solid electrolytes in ASSBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Directly Linking Low-Angle Grain Boundary Misorientation to Device Functionality for GaAs Grown on Flexible Metal Substrates

A new growth method to make highly oriented GaAs thin films on flexible metal substrates has been developed, enabling roll-to-roll manufacturing of flexible semiconductor devices. The grains are oriented in the <001> direction with <1 degree misorientations between them, and they have a comparable mobility to single-crystalline GaAs at high doping concentrations. At the moment, the role of low-angle grain boundaries (LAGBs) on device performance is unknown. A series of electron backscatter diffraction (EBSD) and cathodoluminesence (CL) studies reveal that increased doping concentrations decrease the grain size and increase the LAGB misorientation. Cross-sectional scanning transmission electron microscopy (STEM) reveals the complex dislocation structures within LAGBs. Most importantly, a correlative EBSD/electron beam-induced current (EBIC) experiment reveals that LAGBs are carrier recombination centers and that the magnitude of recombination is dependent on the degree of misorientation. The presented results directly link increased LAGB misorientation to degraded device performance, and therefore, strategies to reduce LAGB misorientations and densities would improve highly oriented semiconductor devices.

36 MATERIALS SCIENCE↗
NASA NTRS1993

The critical density for star formation in HII galaxies

The star formation rate (SFR) in galaxies is believed to obey a power law relation with local gas density, first proposed by Schmidt (1959). Kennicutt (1989) has shown that there is a threshold density above which star formation occurs, and for densities at or near the threshold density, the DFR is highly non-linear, leading to bursts of star formation. Skillman (1987) empirically determined this threshold for dwarf galaxies to be approximately 1 x 10(exp 21) cm(exp -2), at a linear resolution of 500pc. During the course of our survey for HI companion clouds to HII galaxies, we obtained high resolution HI observations of five nearby HII galaxies. HII galaxies are low surface brightness, rich in HI, and contain one or a few high surface brightness knots whose optical spectra resemble those of HII regions. These knots are currently experiencing a burst of star formation. After Kennicutt (1989) we determine the critical density for star formation in the galaxies, and compare the predictions with radio and optical data.

Taylor, Christopher L.↗
NASA NTRS2005

Piezohydraulic Pump Development

Reciprocating piston piezohydraulic pumps were developed originally under the Smart Wing Phase II program (Lynch) and later under the CHAP program (CSA, Kinetic Ceramics). These pumps focused on 10 cm scale stack actuators operating below resonance and, more recently, at resonance. A survey of commercially available linear actuators indicates that obtaining power density and specific power greater than electromagnetic linear actuators requires driving the stacks at frequencies greater than 1 KHz at high fields. In the case of 10 cm scale actuators the power supply signal conditioning becomes large and heavy and the soft PZT stack actuators generate a lot of heat due to internal losses. Reciprocation frequencies can be increased and material losses significantly decreased through use of millimeter scale single crystal stack actuators. We are presently targeting the design of pumps that utilize stacks at the 1-10 mm length scale and run at reciprocating frequencies of 20kHz or greater. This offers significant advantages over current approaches including eliminating audible noise and significantly increasing the power density and specific power of the system (including electronics). The pump currently under development will comprise an LC resonant drive of a resonant crystal and head mass operating against a resonant fluid column. Each of these resonant systems are high Q and together should produce a single high Q second order system.

Lynch, Christopher S.↗
DOE OSTI2026

Covalent adaptable networks for electrolyte–binder integration in recyclable lithium metal batteries

Lithium-metal batteries (LMBs) are considered a promising next-generation energy storage technology due to their exceptionally high energy density. However, the development of solid polymer electrolytes and cathode binders for LMBs faces critical challenges, including interfacial instability, poor recyclability, and growing environmental concerns. In particular, current systems often rely on non-recyclable components featuring permanently crosslinked networks and polyfluoroalkyl substances (PFAS), such as poly(vinylidene fluoride) (PVDF), which cause battery waste and environmental harm. Herein, we introduce a multifunctional covalent adaptable network (CAN) platform based on thermally reversible Diels–Alder (DA) chemistry, designed for dual functionality as a CAN-based electrolyte (CAE) and a CAN-based cathode binder. The CAE achieves high ionic conductivity and strong storage modulus (1.4 mS cm −1 and ∼ 10 5 Pa at room temperature, respectively) and enables stable long-term cycling in symmetric Li||Li cells for over 2000 h with low overpotential. When it is applied as a cathode binder in LiFePO 4 (LFP) composite electrodes (C-LFP), the CAN matrix significantly reduces interfacial resistance and enhances discharge capacity compared to conventional PVDF-based systems. Thermal treatment induces self-healing at the cathode–electrolyte interface, further improving contact and yielding a discharge capacity of 150 mAh g −1 at 0.5 C. Moreover, the dynamic CAN architecture allows efficient recovery and reuse of lithium salts from spent electrolytes through retro-DA reactions under mild conditions (∼80 °C), establishing a low-energy, cost-effective recycling pathway. In conclusion, this work presents a scalable and sustainable strategy for high-performance LMBs by integrating recyclability, interfacial healing, and PFAS-free design, offering a holistic solution aligned with circular economy principles and next-generation battery demands.

Diels–Alder↗
DOE OSTI2024

In-situ two-dimensional temperature measurements using x-ray fluorescence spectroscopy in laminar flames with high silica particle concentrations

X-ray fluorescence spectroscopy (XRF) was used to measure temperatures and study mixing, for the first time in silica particle synthesis flames. Hexamethyldisiloxane (HMDSO) and trimethylsilanol (TMSO) were the particle precursors. A multi-element diffusion burner was used to produce a flat methane flame, and the precursors, dilute in inert gas, were injected via a central jet. Krypton was the fluorescent medium at 3.2 % concentration by volume. Scans with Kr in the central flow and not in the main flow were made to assess the mixing effects between the central and main gas flows. When HMDSO or TMSO were added, a secondary diffusion flame formed between the jet and the main methane flame. The results revealed a dramatic change in the centerline temperature profile of the jet gases when HMDSO or TMSO were added. The main methane flame stoichiometry also affected the temperature profiles. The results show HMDSO and TMSO reactions are initiated in a lowtemperature and low-oxygen concentration region of the jet where thermal decomposition is not expected to be significant. Reaction of the particle precursors is therefore attributed to radical transport from the main methane flame. In the current work, particle number densities of up to 270 g/m 3 locally are estimated. Thus, the study also demonstrates the capability of the XRF technique for high spatial fidelity measurements in flames with high concentrations of condensed-phase particles, leveraging the attribute that the XRF signal is generally not impacted by condensed-phase interferences. In conclusion, the observations and data obtained in this study inform likely reaction pathways for this important class of siloxane compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

Ionospheric and Birkeland current distributions inferred from the MAGSAT magnetometer data

Ionospheric and field-aligned sheet current density distributions are presently inferred by means of MAGSAT vector magnetometer data, together with an accurate magnetic field model. By comparing Hall current densities inferred from the MAGSAT data and those inferred from simultaneously recorded ground based data acquired by the Scandinavian magnetometer array, it is determined that the former have previously been underestimated due to high damping of magnetic variations with high spatial wave numbers between the ionosphere and the MAGSAT orbit. Among important results of this study is noted the fact that the Birkeland and electrojet current systems are colocated. The analyses have shown a tendency for triangular rather than constant electrojet current distributions as a function of latitude, consistent with the statistical, uniform regions 1 and 2 Birkeland current patterns.

Zanetti, L. J.↗
NASA NTRS2002

Current Status of the Gasdynamic Mirror Fusion Propulsion Experiment

Nuclear fusion appears to be the most promising concept for producing extremely high specific impulse rocket engines. One particular fusion concept which seems to be particularly well suited for fusion propulsion applications is the gasdynamic mirror (GDM). An experimental GDM device has been constructed at the NASA Marshall Space Flight Center to provide an initial assessment of the feasibility of this type of propulsion system. An initial shakedown of the device is currently underway with initial experiments slated to occur in late 2001. This device would operate at much higher plasma densities and with much larger L/D ratios than previous mirror machines. The high L/D ratio minimizes to a large extent certain magnetic curvature effects which lead to plasma instabilities causing a loss of plasma confinement. The high plasma density results in the plasma behaving much more like a conventional fluid with a mean free path shorter than the length of the device. This characteristic helps reduce problems associated with 'loss cone' microinstabilities. The device has been constructed to allow a considerable degree of flexibility in its configuration thus permitting the experiment to grow over time without necessitating a great deal of additional fabrication.

Emrich, William J., Jr.↗
NASA NTRS1999

Non-Toxic Orbiter Maneuvering System (OMS) and Reaction Control System

NASA is pursuing the technology and advanced development of a non-toxic (NT) orbital maneuvering system (OMS) and reaction control system (RCS) for shuttle upgrades, RLV, and reusable first stages. The primary objectives of the shuttle upgrades program are improved safety, improved reliability, reduced operations time and cost, improved performance or capabilities, and commonality with future space exploration needs. Non-Toxic OMS/RCS offers advantages in each of these categories. A non-toxic OMS/RCS eliminates the ground hazards and the flight safety hazards of the toxic and corrosive propellants. The cost savings for ground operations are over $24M per year for 7 flights, and the savings increase with increasing flight rate up to $44M per year. The OMS/RCS serial processing time is reduced from 65 days to 13 days. The payload capability can be increased up to 5100 Ibms. The non-toxic OMS/RCS also provides improved space station reboost capability up to 20 nautical miles over the current toxic system of 14 nautical miles. A NT OMS/RCS represents a clear advancement in the SOA over MMH/NTO. Liquid oxygen and ethanol are clean burning, high-density propellants that provide a high degree of commonality with other spacecraft subsystems including life support, power, and thermal control, and with future human exploration and development of space missions. The simple and reliable pressure-fed design uses sub-cooled liquid oxygen at 250 to 350 psia, which allows a propellant to remain cryogenic for longer periods of time. The key technologies are thermal insulation and conditioning techniques are used to maintain the sub-cooling. Phase I successfully defined the system architecture, designed an integrated OMS/RCS propellant tank, analyzed the feed system, built and tested the 870 lbf RCS thrusters, and tested the 6000 lbf OMS engine. Phase 11 is currently being planned for the development and test of full-scale prototype of the system in 1999 and 2000

Hurlbert, Eric A.↗
DOE OSTI2026

High Purity and Reduced Defects Hard Carbon Synthesis for Sodium-Ion Batteries

Hard carbon (HC) is the state-of-the-art anode material for sodium-ion batteries; however, the high-temperature carbonization of precursors (>1100 °C) often introduces inorganic impurities, an issue that remains largely underexplored. Here, we report a simple synthesis strategy for producing high purity HC by carbonizing a cellulose-derived precursor at 1400 °C under a slightly reducing Ar–H2 atmosphere on a graphite substrate, thereby eliminating the aluminum contamination observed during conventional carbonization on an alumina substrate under Ar. In addition, the modified synthetic condition reduces surface defects and the concentration of oxygen-containing functional groups, thereby altering the interphase formation on the HC surface. At a current density of 20 mA g−1, the impurity-rich HC exhibited an initial coulombic efficiency (ICE) of 74.1% and a reversible capacity of 248.8 mAh g−1. In sharp contrast, the high purity HC delivered a significantly improved ICE of 90.1% and a reversible capacity of 345.1 mAh g−1. These results underscore the critical importance of impurity and defect control during HC synthesis and highlight the clear electrochemical advantages of high purity HC with reduced defects for sodium-ion battery anodes.

Harshita, Lohanni↗
DOE OSTI2023

Enhanced Hanford High-Fluoride Waste Glass Property Data Development: Phase 1

This study focused on investigating the effects of fluorine concentration on simulated high-level waste glass properties to eventually establish a fluorine limit (as a single-component or multiple-component constraint) for glass formulations for high-fluoride Hanford wastes. This is a first step to provide data to understand the impacts of changing flowsheets on the mission duration and extent. A test matrix of 20 high-fluoride glasses was generated, and the chemical compositions were measured. The following properties were measured and tested against current model predictions: crystal formation after centerline canister cooling, crystallinity as a function of temperature, density, viscosity, electrical conductivity, toxic leaching characteristics using the toxicity characteristic leach profile (TCLP), product consistency using the product consistency test (PCT), and SO 3 solubility. Overall, current models failed to adequately predict most of the properties, possibly due to differences in compositional space used to generate the models and the current test matrix. Additional work is needed to more accurately assess the impacts of high-fluoride wastes on Hanford processing, including additional data collection over a broader composition region and model development for the key models of interest such as PCT and TCLP.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1990

Oxygen stabilization induced enhancement in J(sub c) and T(sub c) of superconducting oxides

In an attempt to enhance the electrical and mechanical properties of the high temperature superconducting oxides, high T(sub c) composites were prepared composed of the 123 compounds and AgO. The presence of extra oxygen due to the decomposition of AgO at high temperature is found to stabilize the superconducting 123 phase. Ag is found to serve as clean flux for grain growth and precipitates as pinning center. Consequently, almost two orders of magnitude enhancement in critical current densities were also observed in these composites. In addition, these composites also show much improvement in workability and shape formation. On the other hand, proper oxygen treatment of Y5Ba6Cu11Oy was found to possibly stabilize superconducting phase with T(sub c) near 250 K. I-V, ac susceptibility, and electrical resistivity measurements indicate the existence of this ultra high T(sub c) phase in this compound. Detailed structure, microstructure, electrical, magnetic and thermal studies of the superconducting composites and the ultra high T(sub c) compound are presented and discussed.

Wu, M. K.↗
NASA NTRS1991

Oxygen stabilization induced enhancement in superconducting characteristics of high-Tc oxides

In an attempt to enhance the electrical and mechanical properties of the high temperature superconducting oxides, high T(sub c) composites were prepared composed of the 123 compounds and AgO. The presence of extra oxygen due to the decomposition of AgO at high temperature is found to stabilize the superconducting 123 phase. Ag is found to serve as clean flux for grain growth and precipitates as pinning center. Consequently, almost two orders of magnitude enhancement in critical current densities were also observed in these composites. In addition, these composites also show much improvement in workability and shape formation. On the other hand, proper oxygen treatment of Y5Ba6Cu11Oy was found to possibly stabilize superconducting phase with T(sub c) near 250 K. I-V, ac susceptibility, and electrical resistivity measurements indicate the existence of this ultra high T(sub c) phase in this compound. Detailed structure, microstructure, electrical, magnetic and thermal studies of the superconducting composites and the ultra high T(sub c) compound are presented and discussed.

Wu, M. K.↗