Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Operating characteristics of a 60 cm and a 10 cm electric arc-driven shock-tube

This paper describes the current status of the operating characteristics of the electric arc-driven shock-tube facility at Ames Research Center, focusing on its potential usefulness in the current and anticipated future applications. The paper specifically addresses the questions as to: (1) how well the behavior of the arc driver is understood and controlled, (2) how well the facility is equipped to test low-density, very-high-velocity nonequilibrium flow regimes, and (3) how closely the facility is expected to produce an equilibrium hypersonic flow when operated in shock-tunnel modes. For these issues, it is shown that: (1) a plasma kinetics model of the exploding wire closely describes the arc behavior in the driver, (2) the facility can produce a spectroscopically-clean flow in a low density regime with a shock velocity of 13 km/sec in air when used with an aluminum driven tube, and (3) when operated as a shock-tunnel, the high enthalpy flow in the test section is expected to deviate only slightly from the perfect equilibrium flow conditions at enthalpies corresponding to flight speeds of 5 km/sec or less.

Sharma, Surendra P.↗

Experimental Simulation of Meteorite Ablation during Earth Entry Using a Plasma Wind Tunnel

Three different types of rocks were tested in a high enthalpy air plasma flow. Two terrestrial rocks, basalt and argillite, and an ordinary chondrite, with a 10 mm diameter cylindrical shape were tested in order to observe decomposition, potential fragmentation, and spectral signature. The goal was to simulate meteoroid ablation to interpret meteor observation and compare these observations with ground based measurements. The test flow with a local mass-specific enthalpy of 70 MJ kg{sup −1} results in a surface heat flux at the meteorite fragment surface of approximately 16 MW m{sup −2}. The stagnation pressure is 24 hPa, which corresponds to a flight condition in the upper atmosphere around 80 km assuming an entry velocity of 10 km s{sup −1}. Five different diagnostic methods were applied simultaneously to characterize the meteorite fragmentation and destruction in the ground test: short exposure photography, regular video, high-speed imaging with 10 kHz frame rate, thermography, and Echelle emission spectroscopy. This is the first time that comprehensive testing of various meteorite fragments under the same flow condition was conducted. The data sets indeed show typical meteorite ablation behavior. The cylindrically shaped fragments melt and evaporate within about 4 s. The spectral data allow the identification of the material from the spectra which is of particular importance for future spectroscopic meteor observations. For the tested ordinary chondrite sample a comparison to an observed meteor spectra shows good agreement. The present data show that this testing methodology reproduces the ablation phenomena of meteoritic material alongside the corresponding spectral signatures.

79 ASTRONOMY AND ASTROPHYSICS↗

Performance of 1.15-pressure-ratio fan stage at several rotor blade setting angles with reverse flow

A 51 cm diameter low pressure ratio fan stage was tested in reverse flow. Survey flow data were taken over the range of rotative speed from 50 percent to 100 percent design speed at several rotor blade setting angles through both flat and feather pitch. Normal flow design values of pressure ratio and weight flow were 1.15 and 29.9 kg/sec with a rotor tip speed of 243.8 m/sec. The maximum thrust in reverse flow was 52.5 percent of design thrust in normal flow.

Kovich, G.↗

NASA AETC Test Technology Subproject

Funds directed to improve measurement capabilities (pressure, force, flow, and temperature), test techniques and processes, and develop technologies critical to meeting NASA research needs and applicable to a multitude of facilities. Primarily works by funding small ($40K - $400K) tasks which result in a demonstration or initial capability of a new technology in an AETC facility.TT research and development tasks are generally TRL 3-6; they should be things which work in small scale or lab environments but need further development for use in production facilities.TT differs from CA in its focus on smaller-scale tasks and on instrumentation. Technologies developed by TT may become CA projects in order be fully realized within a facility.

Bell, James↗

Permeability of laboratory-formed methane-hydrate-bearing sand: Measurements and observations using x-ray computed tomography

Methane hydrate was formed in two moist sands and a sand/silt mixture under a confining stress in an X-ray-transparent pressure vessel. Three initial water saturations were used to form three different methane-hydrate saturations in each medium. X-ray computed tomography (CT) was used to observe location-specific density changes caused by hydrate formation and flowing water. Gas-permeability measurements in each test for the dry, moist, frozen, and hydrate-bearing states are presented. As expected, the effective permeabilities (intrinsic permeability of the medium multiplied by the relative permeability) of the moist sands decreased with increasing moisture content. In a series of tests on a single sample, the effective permeability typically decreased as the pore space became more filled, in the order of dry, moist, frozen, and hydrate-bearing. In each test, water was flowed through the hydrate-bearing medium and we observed the location-specific changes in water saturation using CT scanning. We compared our data to a number of models, and our relative permeability data compare most favorably with models in which hydrate occupies the pore bodies rather than the pore throats. Inverse modeling (using the data collected from the tests) will be performed to extend the relative permeability measurements.

54 ENVIRONMENTAL SCIENCES↗

Heat Exchanger Intensification Through Powder Processing and Enhanced Design (HIPPED)

High intensity, supercritical CO 2 heat exchangers capable of operating at temperatures between 800 and 1100 ˚C and pressures greater than 80 bar are considered a critical component for high efficiency power generation and a range of next-generation industrial processes. A novel heat exchanger concept was proposed in this project. The proposed concept involved a plate-type architecture with three-dimensional fins, called twisted s-shaped fins, that capitalize on additive manufacturing. Four manufacturing processes were studied to realize the complex envisioned design: press and sinter of metallic powders, directed energy deposition, laser powder bed fusion, and a novel powder bed process involving a photoreactive polymer called SEAM (scalable expeditious additive manufacturing), that later was developed at MSU. The team was able to manufacture subscale heat exchangers using laser powder bed fusion (LPBF) and SEAM. The team settled on using SEAM as a final manufacturing approach due to its very low cost. The SEAM-manufactured heat exchanger, however, when tested under pressure, exhibited leaks and the process still requires further development beyond the timeline of the project. To support the heat exchanger design and testing, the team developed a new high temperature flow loop allowing testing under high temperature and pressure. Computational modeling of the heat exchanger was also performed for the twisted s-shaped fins and the computations were validated with experimental data. The new twisted fins resulted in enhanced heat transfer and reduced pressure drop. To further minimize pressure drop in the plate heat exchanger, the team also developed a simplified model for flow maldistribution in the manifolds, providing a new tool for designers that eliminates the need for complex CFD calculations. A technoeconomic analysis was also developed to contrast SEAM with LPBF, this tool indicated that SEAM is several times less costly and offer significant promises as a rapid low cost additive manufacturing process for metallic systems.

30 DIRECT ENERGY CONVERSION↗

Internal performance of Highly Integrated Deployable Exhaust Nozzles

The internal performance characteristics of Highly Integrated Deployable Exhaust Nozzles (HIDEN) applicable to advanced short take-off and vertical landing aircraft have been investigated. Four nozzle concepts, designed for fan and core flow installations, were tested with varying contraction ratio and nozzle exit plane shape. In addition, two offtake duct designs, along with several centerbody and blocker geometries were tested to evaluate their effect on the static thrust and flow performance. This investigation was conducted in the static test facility of the NASA Langley 16-Foot Transonic Tunnel. A six-component strain-gage balance collected force and moment data, and static pressure, total pressure, and total temperature measurements were also made internal to the model. Room temperature, dry high-pressure air was used to simulate jet exhaust. The results indicate that the internal performance of these HIDEN concepts is comparable to previously tested nozzle concepts designed for thrust vectoring about a bearing plane. This report presents the configuration design of the HIDEN concepts and the results of the internal performance testing.

Taylor, John G.↗

Design and Analysis of A Jet Stretcher for High-Altitude Supersonic Free Jet Testing

A jet stretcher can be used to extend the region of clean flow for a test article in a supersonic free jet. The device acts to shield the article from shock waves reflected from the free jet shear layer. It can also allow for overexpanded nozzle operation through blocking shocks emanating from the nozzle lip, enlarging the potential test envelope. The FUN3D computational fluid dynamics solver was used to test a design process for developing jet stretchers. The inner surface of the axisymmetric jet stretcher was obtained from a streamline extracted from a free flight simulation around a notional test article at the intended test condition of Mach 3.2, 53,000 ft. The test article and jet stretcher were then simulated in a free jet nozzle exhaust, and the flowfield within a notional inlet aperture was compared between the installed and free flight calculations. Ambient pressure was increased until separation within the free jet nozzle finally induced disturbances at the inlet. The jet stretcher was shown to provide clean flow to the inlet at cell pressure ratios up to 2.8. A process for trimming the axisymmetric jet stretcher was also tested. This was intended to provide blockage relief for complex test articles, aiding with starting, as well as reducing weight and fabrication cost. The trimmed jet stretcher performed identically to the axisymmetric model at slightly-overexpanded conditions, but at cell pressure ratios above 1.3 allowed disturbances from the trailing edge to reach the inlet.

free jet↗

Design and Analysis of A Jet Stretcher for High-Altitude Supersonic Free Jet Testing

A jet stretcher can be used to extend the region of clean flow for a test article in a supersonic free jet. The device acts to shield the article from shock waves reflected from the free jet shear layer. It can also allow for overexpanded nozzle operation through blocking shocks emanating from the nozzle lip, enlarging the potential test envelope. The FUN3D computational fluid dynamics solver was used to test a design process for developing jet stretchers. The inner surface of the axisymmetric jet stretcher was obtained from a streamline extracted from a free flight simulation around a notional test article at the intended test condition of Mach 3.2, 53,000 ft. The test article and jet stretcher were then simulated in a free jet nozzle exhaust, and the flowfield within a notional inlet aperture was compared between the installed and free flight calculations. Ambient pressure was increased until separation within the free jet nozzle finally induced disturbances at the inlet. The jet stretcher was shown to provide clean flow to the inlet at cell pressure ratios up to 2.8. A process for trimming the axisymmetric jet stretcher was also tested. This was intended to provide blockage relief for complex test articles, aiding with starting, as well as reducing weight and fabrication cost. The trimmed jet stretcher performed identically to the axisymmetric model at slightly overexpanded conditions, but at cell pressure ratios above 1.3 allowed disturbances from the trailing edge to reach the inlet.

free jet↗

Supercritical CO2 studies: micro-channel heat transfer for reactor heat exchangers & cycle design

An experimental facility was built to perform heat transfer and pressure drop measurements in supercritical carbon dioxide. Inlet temperatures ranged from 30-125 degress C with mass velocities ranging from 118-1050 kg/m 2 s and system pressures of 7.5-10.2 MPa. Tests were performed in horizontal, upward, and downward flow conditions to test the influence of buoyance foreces on the heat transfer. The majority of experiments were performed in the cooling mode, where the fluid decreases in temperature over the test section length.

Corradini, Michael↗

Two-phase choked flow of subcooled oxygen and nitrogen

Data are presented for two-phase critical flow through nozzles. Test results from two converging-diverging nozzles and two separate test facilities are in excellent agreement. The critical flow rate and critical flow pressure ratio data conclusively demonstrate that the principle of corresponding states can be applied to two-phase choked flow through nozzles. Normalizing parameters were developed to correlate these data, and current theories can provide an adequate means for extrapolating to other fluids. Such information can be useful for cryogenic fluid storage applications.

Hendricks, R. C.↗

A two-equation turbulence model for two-phase jets

A recently-developed two-equation turbulence model for two-phase flows (Elghobashi and Abou-Arab, 1983) is tested for the flow of a turbulent axisymmetric gaseous jet laden with spherical solid particles of uniform size. The agreement between the predictions of experimental data is good.

Elghobashi, S.↗

Research and test facilities

A description is given of each of the following Langley research and test facilities: 0.3-Meter Transonic Cryogenic Tunnel, 7-by 10-Foot High Speed Tunnel, 8-Foot Transonic Pressure Tunnel, 13-Inch Magnetic Suspension & Balance System, 14-by 22-Foot Subsonic Tunnel, 16-Foot Transonic Tunnel, 16-by 24-Inch Water Tunnel, 20-Foot Vertical Spin Tunnel, 30-by 60-Foot Wind Tunnel, Advanced Civil Transport Simulator (ACTS), Advanced Technology Research Laboratory, Aerospace Controls Research Laboratory (ACRL), Aerothermal Loads Complex, Aircraft Landing Dynamics Facility (ALDF), Avionics Integration Research Laboratory, Basic Aerodynamics Research Tunnel (BART), Compact Range Test Facility, Differential Maneuvering Simulator (DMS), Enhanced/Synthetic Vision & Spatial Displays Laboratory, Experimental Test Range (ETR) Flight Research Facility, General Aviation Simulator (GAS), High Intensity Radiated Fields Facility, Human Engineering Methods Laboratory, Hypersonic Facilities Complex, Impact Dynamics Research Facility, Jet Noise Laboratory & Anechoic Jet Facility, Light Alloy Laboratory, Low Frequency Antenna Test Facility, Low Turbulence Pressure Tunnel, Mechanics of Metals Laboratory, National Transonic Facility (NTF), NDE Research Laboratory, Polymers & Composites Laboratory, Pyrotechnic Test Facility, Quiet Flow Facility, Robotics Facilities, Scientific Visualization System, Scramjet Test Complex, Space Materials Research Laboratory, Space Simulation & Environmental Test Complex, Structural Dynamics Research Laboratory, Structural Dynamics Test Beds, Structures & Materials Research Laboratory, Supersonic Low Disturbance Pilot Tunnel, Thermal Acoustic Fatigue Apparatus (TAFA), Transonic Dynamics Tunnel (TDT), Transport Systems Research Vehicle, Unitary Plan Wind Tunnel, and the Visual Motion Simulator (VMS).

Source record↗

Conceptual design for spacelab two-phase flow experiments

KC-135 aircraft tests confirmed the gravity sensitivity of two phase flow correlations. The prime component of the apparatus is a 1.5 cm dia by 90 cm fused quartz tube test section selected for visual observation. The water-cabin air system with water recycle was a clear choice for a flow regime-pressure drop test since it was used satisfactorily on KC-135 tests. Freon-11 with either overboard dump or with liquid-recycle will be used for the heat transfer test. The two experiments use common hardware. The experimental plan covers 120 data points in six hours with mass velocities from 10 to 640 kg/sec-sq m and qualities 0.01 to 0.64. The apparatus with pump, separator, storage tank and controls is mounted in a double spacelab rack. Supporting hardware, procedures, measured variables and program costs are defined.

Bradshaw, R. D.↗

Design and testing of a sensitive heat-flow calorimeter for measuring radioactive waste in 55-gallon (US) drums - 15334

A sensitive large volume calorimeter for measuring the thermal power generated by the radioactive decay of heat producing materials in 55-gallon drums has been developed and tested. The technology is applicable to the measurement of all radionuclides that decay by alpha or beta decay such as waste or product material containing plutonium, tritium and americium. It is also relevant to the measurement of drums where gamma rays from radioactive decay are captured locally in attenuating materials and the resulting rate of thermal energy deposition (sample thermal power) is of sufficient magnitude for a calorimetry measurement. The initial application of the drum calorimeter is for measuring and characterizing plutonium-bearing waste drums. The calorimeter design has optimised the two characteristics of high thermal sensitivity and reduced measurement times. In order to achieve these characteristics for large volume drums, the heat-flow method of operation was chosen in a single measurement chamber configuration. Using a drum-lifting device, the waste drum is positioned on a sliding platform and subsequently moved by the operator inside an octagonal inner chamber, which acts as the heat sink. The heat-sink chamber has significant thermal inertia and remains effectively at a constant temperature throughout the duration of a drum measurement. The octagonal inner measurement chamber is constructed inside a multi-layer external thermal enclosure, which provides both thermal insulation and significant thermal inertia. The external thermal enclosure isolates the measurement process from the effects of changes in the external ambient temperature. During a measurement, heat flows from the drum being measured to the heat sink. This heat-flow is measured by a series of thermopile sensor assemblies, which are positioned between the waste drum and the heat sink. A high sensitivity of greater than 200 μV/mW (microvolts per milliwatt) has been achieved using multiple close-coupled thermopile sensors in each assembly. Reduced measurement times are achieved by positioning the thermopile sensor assemblies close to the drum surface in order to reduce the thermal transport delay. The instrument incorporates a calibrated precision power supply, which requires annual recalibration and is traceable to national standards. It is used to power a calibration heater that has been built into a calibration and test drum. The calibration and test drum is used both to calibrate the instrument and provide periodic confirmation of correct operation. Measurements of calorimeter performance are reported for a range of drum thermal powers. Long-term temperature drift measurements are used to provide estimates of the minimum detectable drum thermal power and hence the minimum detectable activity for both plutonium and tritium. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Flow Visualization for Plume-Surface Interaction Testing Within Large-Scale Vacuum Environments at Conditions Relevant to Lunar and Martian Landers

Interactions between rocket exhaust plumes and the landing surface during powered spacecraft descent on the Moon and Mars pose significant risks to the landing vehicle, landing site, and nearby infrastructure. Understanding the underlying plume-surface interaction phenomena through ground test data can provide critical insights on the sensitivities of parameters such as the spacecraft altitude and thrust. In the present work, we summarize a scaled ground test recently conducted within a 20-ft vacuum chamber environment located in the historical East Test Area at the NASA Marshall Space Flight Center. The ground test featured a Mach 5.3 inert gas plume impinging upon an instrumented flat plate. Planar laser-induced fluorescence, which is a 2D laser-based flow field measurement technique, was performed at this test area for the first time to visualize salient flow features such as the barrel shock, stagnation shock, and wall jet. Measurements were obtained at discrete lander altitudes, made dimensionless using the nozzle exit diameter, corresponding to h/D = 10, 8, 5, 4, 3, and 2. The stagnation pressures of the plume were varied from approximately 0.04 to 1 MPa, providing sensitivity to the engine thrust of a powered spacecraft. The unique test facility allowed for near-lunar conditions to be obtained at initial vacuum chamber pressures less than 0.1 Pa. Martian-relevant measurements were also performed at ambient pressures near 600 Pa. Furthermore, a third set of measurements were obtained at so called lunar-relevant conditions near 3 Pa chamber pressure

Plume Surface Interaction↗

Flow Visualization for Plume-Surface Interaction Testing Within Large-Scale Vacuum Environments at Conditions Relevant to Lunar and Martian Landers

Interactions between rocket exhaust plumes and the landing surface during powered spacecraft descent on the Moon and Mars pose significant risks to the landing vehicle, landing site, and nearby infrastructure. Understanding the underlying plume-surface interaction phenomena through ground test data can provide critical insights on the sensitivities of parameters such as the spacecraft altitude and thrust. In the present work, we summarize a scaled ground test recently conducted within a 20-ft vacuum chamber environment located in the historical East Test Area at the NASA Marshall Space Flight Center. The ground test featured a Mach 5.3 inert gas plume impinging upon an instrumented flat plate. Planar laser-induced fluorescence, which is a 2D laser-based flow field measurement technique, was performed at this test area for the first time to visualize salient flow features such as the barrel shock, stagnation shock, and wall jet. Measurements were obtained at discrete lander altitudes, made dimensionless using the nozzle exit diameter, corresponding to h/D = 10, 8, 5, 4, 3, and 2. The stagnation pressures of the plume were varied from approximately 0.04 to 1 MPa, providing sensitivity to the engine thrust of a powered spacecraft. The unique test facility allowed for near-lunar conditions to be obtained at initial vacuum chamber pressures less than 0.1 Pa. Martian-relevant measurements were also performed at ambient pressures near 600 Pa. Furthermore, a third set of measurements were obtained at so called lunar-relevant conditions near 3 Pa chamber pressure.

Plume Surface Interaction↗

An optical technique for examining aircraft shock wave structures in flight

The detailed properties of sonic booms have to be better understood before commercial, next generation, supersonic and hypersonic aircraft can be properly developed. Experimental tests and measurements are needed to help sort the physical details of the flows at realistic test conditions. Some of these tests can be made in wind tunnels, but the need for full flight conditions simulation, the problem of tunnel wall interference, and the short distance the shocks can be examined from the aircraft, limit the usefulness of wind tunnel tests. Previous measurement techniques for examining the flow field of aircraft in flight have included pressure measurements on the aircraft, ground based pressure measurements, and flow field measurements made with chase aircraft. Obtaining data with chase planes is a slow and difficult process, and is limited in how close it can be obtained to the test aircraft. A need clearly existed for a better technique to examine the shock structure from the plane to large distances from the plane. A new technique has been recently developed to obtain schlieren photographs of aircraft in flight (SAF). Preliminary results have been obtained, and the technique holds promise as a tool to study the shape and approximate strength of the shock wave structure around the test aircraft, and examine shock wave details all the way from the aircraft to near the ground. The current paper describes this approach, and gives some preliminary test results.

Weinstein, Leonard M.↗