Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Stacking Faults and Short-Range Magnetic Correlations in Single Crystal Y 5 Ru 2 O 12 : A Structure with Ru +4.5 One-Dimensional Chains

In this paper, the synthesis, structure, and physical properties of Y 5 Ru 2 O 12 , a new member of the Ln 5 B 2 O 12 class (Ln = lanthanide, B = Ru, Re, Mo) are reported. Single crystals of Y 5 Ru 2 O 12 are synthesized using a high-temperature, high-pressure (700 °C, 200 MPa) hydrothermal method. The structure features edge-sharing Ru—O—Ru 1D chains of distorted RuO6 octahedra. The YO n (n = 6 and 7) polyhedral groups bridge Ru—O—Ru chains across the unit cell by forming a complex 3D structure. The Ru—O—Ru chains contain alternating shorter and longer Ru—Ru distances along the chain. Single crystal neutron diffraction shows streak-like diffuse scattering along the H-direction, due to stacking faults. Temperature-dependent anisotropic magnetic measurements reveal a broad feature over a wide temperature range, with a maximum at ≈70 K indicating potential short-range ordering, with canted antiferromagnetic behavior below 30 K. The dominant magnetic interactions are antiferromagnetic with a large negative Weiss temperature θ ≈ –200 K. The compound has an effective magnetic moment that is anomalously large for this class of compounds (≈4 μ B Ru –1 ), and a phenomenological spin Hamiltonian describing the unusual anisotropic magnetization of Y 5 Ru 2 O 12 is proposed.

36 MATERIALS SCIENCE↗

Spectroscopic Characterization of Highly Active Fe–N–C Oxygen Reduction Catalysts and Discovery of Strong Interaction with Nafion Ionomer

Scaling up clean-energy applications necessitates the development of platinum group metal (PGM)-free fuel cell electrocatalysts with high activity, stability, and low cost. Here, X-ray absorption (XAS) at the Fe K-edge and Fe K β X-ray emission (XES) spectroscopies were used to study the electronic structure of Fe centers in highly active Fe–N–C oxygen reduction catalysts with significant commercial potential. X-ray absorption near-edge structure (XANES) analysis has shown that the majority (>95%) of Fe centers are in the Fe 3+ oxidation state, while extended X-ray absorption fine structure (EXAFS) detected a mixture of single site Fe–N 4 centers (>95%) and centers with short (~2.5 Å) Fe–Fe interactions of Fe metal and/or Fe-carbide nanoparticles (<5%) featuring the Fe o oxidation state. Surprisingly, addition of Nafion, the most widely used ionomer, resulted in pronounced changes in the XAS spectra, consistent with a strong catalyst–ionomer interaction where long Fe–Fe interactions at ~3.1 Å were shown to be a feature of Fe 3+ ions bound with the Nafion. We conclude that exposure to Nafion during the device formulation has a different effect from the aggressive acid leaching typically used in the preparation of Fe–N–C catalysts. Furthermore, it was hypothesized that the polymer interacts with single sites’ Fe 3+ centers, as well as with graphene layers protecting the Fe o nanoparticles, and extracts some Fe ions into the Nafion matrix.

25 ENERGY STORAGE↗

Effect of outer divertor leg detachment on the high field side scrape-off layer in DIII-D and ASDEX Upgrade

In this work, evidence is presented that detachment of the outer divertor leg leads to a reduction of electron density and neutral pressure in the high-field side (HFS) scrape-off layer (SOL) of the ASDEX Upgrade (AUG) and DIII-D tokamaks with ion $B$ x $∇B$ drift directed toward the X-point (favorable configuration). These results are observed across multiple diagnostics and without the use of impurity seeding to reach detachment. In AUG, outer divertor leg detachment correlates with a decrease in electron density near the separatrix at the inner midplane, measured with HFS reflectometry. A concurrent reduction in inner divertor density and neutral pressure at the inner target is observed using divertor Thomson scattering and neutral pressure gauges. These effects are present in both L- and H-mode plasmas. In DIII-D, a similar reduction is detected through analysis of line-integrated hydrogenic emission measured by multiple diagnostics in the HFS SOL close to the separatrix. The consistent trends in both devices indicate that high electron density and strong hydrogenic emissivity in the HFS SOL are common features of H-mode plasmas in the favorable configuration, independent of wall material and divertor geometry. In L-mode plasmas, the reduction in electron density and neutral pressure is not observed in DIII-D, possibly due to differences in wall material. These results emphasize the importance of the divertor state in determining the two-dimensional neutral distribution and edge fueling.

detachment↗

Studying Wind Loading on CSP Collectors to Improve Performance and Reliability

Electricity generation through Concentrating Solar-thermal Power (CSP) adds the advantage of thermal energy storage and heat production. CSP collector costs constitute nearly one-third of total plant costs. Managing wind loading, especially dynamic wind loading caused by the turbulent wind flow, is a significant design challenge. Traditional collector designs rely on wind tunnel experiments and numerical simulations, which do not fully capture dynamic effects. Here, we provide an overview of NREL's activities on wind loading on CSP collectors, aiming to improve their reliability and cost-efficiency. We present insights from field measurements at operational parabolic trough and power-tower CSP plants. Over two years, we measured turbulent wind fields and resulting structural loads in a parabolic trough plant, revealing wind, turbulence, and collector field interactions. Similar measurements are ongoing at the Crescent Dunes heliostat field. These campaigns show how atmospheric turbulence, wind direction, and collector orientation affect dynamic wind loading. Upwind collector structures can generate turbulent structures, causing fluctuating loads at downstream collectors, impacting fatigue lifetime and optical efficiency. Preliminary results indicate that interior collectors experience higher turning moments than those at the edges, suggesting higher drive wear. At Crescent Dunes, we use instrumented heliostats at the field's edge and interior to study the translation of turbulent wind to dynamic structural loads. The campaign is still ongoing, and we will present first findings. Another focus of our work is tying the experimental wind loading findings to optical performance of the collectors, using simulation tools. For example, we derive torsional errors of the parabolic troughs - the angular offset from the sun position along a collector row. This error is impacted by wind-induced mirror deformations. Future work will focus on continuing the measurement efforts and combining them with computational fluid dynamic simulations. By providing detailed field measurements and validated models, our efforts aim to enhance understanding of wind loading on CSP collectors, improving their structural integrity and optical performance.

CSP↗

The Geothermal Entrepreneurship Organization (GEO) Accelerating Technology Transfer, Testing and Adoption of Cutting-edge Extreme Environment Drilling

The Geothermal Entrepreneurship Organization launched in 2019 with the goal of building a geothermal innovation ecosystem at the University of Texas at Austin (UT Austin), and in the State of Texas at large. The theses underlying the work of GEO were 1) that with targeted advocacy, recruitment, organization, and coalition building, research institutions with legacy excellence in petroleum and geosystems engineering could become engines of geothermal innovation, research and development; 2) that startups were the appropriate vehicle to speed these innovations from the lab into the field, and building a geothermal startup ecosystem in Texas would not only advance next generation geothermal concepts into the field, but also help spur oil and gas engagement in the space, and 3) that with targeted engagement, education, and recruitment across stakeholders in the oil and gas industry and the State of Texas generally, the oil and gas industry, and other legacy oil and gas entities in the State could become sources of large scale deployment of geothermal energy. The overall goal was to create a ‘snowball’ effect, where targeted impactful actions would catalyze self-sustaining, organic growth of a new geothermal ecosystem in the State of Texas. That goal was achieved through GEO’s work. To test its theses, GEO began work by interviewing and recruiting UT Austin faculty and alumni into geothermal. At the beginning of the GEO project, there was no geothermal activity ongoing within the UT Austin Petroleum and Geosystems Engineering Department, the Bureau of Economic Geology, or the Jackson School of Geoscience, and many faculty approached had not before considered how their skillsets might apply in the space. By the end of the project period, three major research consortia focused on geothermal were launched as a result of GEO’s work, one at the Bureau of Economic Geology, one within the Petroleum and Geosystems Engineering Department, and another organized by GEO across six research institutions across the State of Texas, called the Texas Geothermal Institute. Geothermal curricula was launched at UT Austin, and UT Austin began attracting new geothermal enthusiasts into its faculty, including Dr. Silviu Livescu, former Chief Scientist of Baker Hughes. Startups recruited and mentored by GEO launched, raised funding, and deployed (or are currently deploying) their concepts in the field. By the end of the project period, the GEO concept expanded to faculty beyond UT Austin to other institutions, like Texas A&M, the University of Houston, and Rice University, and geothermal engagement began at those institutions as well. Multiple faculty members and alumni across these institutions launched geothermal startup companies, launched geothermal research consortia, and/or began teaching geothermal courses. In 2020, GEO launched what was to become the largest geothermal conference in the world by its second year, ‘PIVOT – From Hydrocarbons to Heat’, and the resulting momentum catalyzed the Society of Petroleum Engineers to launch a geothermal technical section, drove more startups to launch out of the ecosystem, and drove actors in the State of Texas, NGOs, and stakeholders globally to become engaged. Riding this momentum, the Texas Geothermal Energy Alliance was launched, the first ever industry association dedicated to advancing geothermal energy in the State of Texas. The Texas geothermal ecosystem after only two years of building and support is now robust, quickly growing, and self-sustaining. By 2021, the Texas geothermal ecosystem had attracted the attention of philanthropists, funding entities, media, and influencers outside of Texas, and GEO’s executive director was invited to give a TED talk about oil and gas engagement in building the future of geothermal energy, which elevated the success of the ecosystem to a global audience.

15 GEOTHERMAL ENERGY↗

Leveraging generative AI for urban digital twins: a scoping review on the autonomous generation of urban data, scenarios, designs, and 3D city models for smart city advancement

The digital transformation of modern cities by integrating advanced information, communication, and computing technologies has marked the epoch of data-driven smart city applications for efficient and sustainable urban management. Despite their effectiveness, these applications often rely on massive amounts of high-dimensional and multi-domain data for monitoring and characterizing different urban sub-systems, presenting challenges in application areas that are limited by data quality and availability, as well as costly efforts for generating urban scenarios and design alternatives. As an emerging research area in deep learning, Generative Artificial Intelligence (GenAI) models have demonstrated their unique values in content generation. This paper aims to explore the innovative integration of GenAI techniques and urban digital twins to address challenges in the planning and management of built environments with focuses on various urban sub-systems, such as transportation, energy, water, and building and infrastructure. The survey starts with the introduction of cutting-edge generative AI models, such as the Generative Adversarial Networks (GAN), Variational Autoencoders (VAEs), Generative Pre-trained Transformer (GPT), followed by a scoping review of the existing urban science applications that leverage the intelligent and autonomous capability of these techniques to facilitate the research, operations, and management of critical urban subsystems, as well as the holistic planning and design of the built environment. Based on the review, we discuss potential opportunities and technical strategies that integrate GenAI models into the next-generation urban digital twins for more intelligent, scalable, and automated smart city development and management.

3D city modeling↗

Influence of Aerosol Embedded in Shallow Cumulus Cloud Fields on the Surface Solar Irradiance

Ubiquitous shallow cumulus clouds are associated with complex variability in surface solar irradiance (SSI). Aerosol embedded in the cloud field typically has a much smaller overall radiative effect, but can significantly perturb the shape of the SSI probability density function (PDF). These perturbations have important implications for several applications that utilize SSI, but are poorly quantified and are the subject of this study. Multiple cases of shallow cumulus cloud fields with embedded aerosol are simulated at the Southern Great Plains Atmospheric Observatory using large eddy simulation (LES). The LES-derived cloud and aerosol fields are then ingested into Monte Carlo three-dimensional (3D) radiative transfer to simulate SSI. We find a variety of perturbations to the SSI PDF that depend on aerosol presence and optical properties. The processes leading to these perturbations include extinction of the direct beam that often increases from the clear-sky region toward cloud edge due to aerosol hygroscopic growth, and scattering of radiation by aerosol into cloud shadows. The ability to predict the SSI PDF in the presence of aerosol is assessed by adding three representative aerosol optical properties into an existing machine learning framework. We show that machine learning accurately predicts the SSI PDF across a wide range of conditions with negligible computational expense. Importance metrics reveal the relatively high influence of aerosol optical properties in making the predictions. These new findings highlight the important role that aerosol plays in SSI variability for highly 3D cloud-aerosol environments and provides a computationally efficient route forward for its simulation.

3D radiative transfer↗

Numerical simulation of Li-pellet injection experiments for ELM-pacing in EAST

The injection of light impurity granules into fusion research discharges has shown a great potential for ELM pacing in future nuclear devices. The present work employed a model considering both pellet ablation and transport to systematically study for the first time the evolution of both impurity Li species and target plasma in the edge plasma during single and repeated Li pellet injections, with all initial information extracted from the EAST experiments. The evolutionary distributions of atomic and ionized Li species were presented and show good consistency with experimental CCD camera images. Simulation studies were carried out for single and repeated pellet injections at the outer mid-plane, and statistical uncertainty of ELM pacing rates triggering ELMs is discussed with regard to related injection conditions. It is found that the pressure locally caused by an ELM pacing pellet (with a diameter of 0.6 ~ 0.7 mm) was 1.8–2.4 times its unperturbed magnitude in the EAST shots of interest. Accumulation from repeated pellet injections results in the rise of pedestal height at a high injection frequency and this effect becomes stronger with increasing pellet size. Pressure changes are also evident in a scenario of multiple small pellets per stroke, which could lead to a nonnegligible, probabilistic ELM triggering rate observed experimentally. The effects of other possible factors are also discussed. With the assumption that the ELM trigger rate of a Li pellet of 0.7 mm diameter is 100%, the predicted trigger rates are in good agreement with those observed in experiments. This work can help understand the statistically probabilistic behavior of ELM triggering efficiency observed in previous studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Iron precipitation under controlled oxygen flow: Mineralogical implications for BIF precursors in the Archean ocean

Banded iron formation (BIF) deposition in the Archean ocean is thought to have been initiated by the oxidation of dissolved iron into ferric primary precursor phases that descended through the water column and were deposited on the seafloor. Effective interpretation of the trace element and isotopic composition of BIFs in the geologic record requires an understanding of the identity and longevity of those precursor phases. Temporal and spatial variation in oxidant concentration and ocean chemistry may have driven precursor mineralogy. Furthermore, precursor phases may undergo transitions during descent and burial. This experimental study follows the evolution of iron mineralogy, speciation, and redox state during the precipitation of iron under variable oxygen fluxes and in fluids containing different iron-complexing anions (chloride, sulfate, and phosphate). Additionally, suspensions collected after incomplete oxidation were anoxically aged to simulate changes to precursor mineralogy during descent below the seawater redoxcline. Results from X-ray diffraction, sequential dissolution, colorimetric determination of Fe redox state, and Fe K-edge X-ray absorption fine structure spectroscopy showed that under all experimental conditions, intermediate precipitates collected before complete iron uptake contained mineralized ferrous iron. Purely ferric mineral assemblages were not observed until iron was removed from solution. In low-oxygen experiments, intermediate precipitates contained phases with stoichiometric Fe 2+ , including magnetite, vivianite, and green rust (GR). Chloride green rust (GR1) had more ferric iron than sulfate green rust (GR2) and more readily transitioned to magnetite via disproportionation. GR2 was stable over a broader range of iron uptake; magnetite appeared mainly as an additional oxidation product in sulfate solution. In high oxygen experiments, mineralized ferrous iron occurred in amorphous phases or as a non-stoichiometric component in ferric oxides; final ferric assemblages were less crystalline than in low-oxygen equivalents. Low concentrations of phosphate increased the total iron oxidation rate, but also increased the ferrous content of intermediate precipitates. The incorporation of phosphate stabilized GR2 and facilitated GR2 precipitation over a larger range of iron uptake. In higher concentrations of phosphate, vivianite and poorly crystalline ferric hydroxides formed in place of GR. Here, these findings suggest that over a range of possible ocean chemistries, mixed-valence phases may have been short lived but relevant precursors to BIF. Additionally, anionic chemistry and oxidant concentration are shown to influence the crystallinity and chemical resistivity of final ferric assemblages, affecting their reactivity during later anoxic burial.

58 GEOSCIENCES↗

Toward accurate measurement of electromagnetic field by retrieving and refining the center position of non-uniform diffraction disks in Lorentz 4D-STEM

Recent advancement in scanning transmission electron microscopy (STEM) allows the use of 4D-STEM, a technique that captures an electron diffraction pattern at each scan point in STEM, to measure electrostatic and magnetic potential and field in materials. However, accurate measurement, separation of the magnetic and electric signals, and removal of artifacts remain challenging, especially in the presence of complex non-uniform diffraction contrast within the disks. In this work, based on dynamic simulations of 4D-STEM patterns built upon superstructures consisting of millions of atoms to account for different sample thickness and edge geometries, we show how the shape and intensity distribution of the central disk are affected by multiple scattering. We propose a robust refinement procedure through iteration of the spin-sensitive peak position of the disk-center in the circular Hough transform filtered images from experimental Lorentz 4D-STEM dataset after minimizing the possible artifacts, such as those due to the change of thickness, dynamic scattering, and scanning process. We verify that caution must be taken as in practice the rigid-disk-shift model used to reconstruct induction maps can easily break down due to disk-protrusion when there exists a nonconstant phase gradient or thickness within the width of the probe. Through quantitative analysis and comparing experiment with calculation the effect of the non-spin-related intensity distribution inside the disk as well as that causes the disk shift due to the intensity-protrusion can be removed, and high-quality magnetic field mapping is possible.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Computational analysis of ion orbital loss in diverted positive- and negative-triangularity tokamaks

The mechanism of ion orbital loss in diverted negative-triangularity (NT) tokamaks is significantly different from that of positive-triangularity (PT) tokamaks. The orbital loss from the edge of NT tokamaks can be quite large, because the separatrix X-point is located on the outboard side, meaning that trapped ions crossing the separatrix are lost to the inboard divertor plate after a mirror reflection on the side of the strong magnetic field. NT tokamaks have difficulties in building up steep pressure gradients in the edge regions. However, the majority of trapped ions crossing the separatrix in PT tokamaks survive (through complete banana motions) without reaching the X-point region. For NT tokamaks, topological changes in the trapped ion trajectories can be achieved in the presence of the radial electric field, thus reducing the orbital loss, whereas for PT tokamaks, the orbital loss is relatively insensitive to the radial electric field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A gyrokinetic simulation model for 2D equilibrium potential in the scrape-off layer of a field-reversed configuration

The equilibrium potential structure in the scrape-off layer (SOL) of the field-reversed configuration (FRC) can be affected by the penetration of edge biasing applied at the divertor ends. The primary focus of the paper is to establish a formulation that accurately captures both parallel and radial variations of the two-dimensional (2D) potential in SOL. The formulation mainly describes a quasi-neutral plasma with a logical sheath boundary. A full-f gyrokinetic ion model and a massless electron model are implemented in the GTC-X code to solve for the self-consistent equilibrium potential, given fixed radial potential profiles at the boundaries. The first essential point of this 2D model lies in its ability to couple radial and parallel dynamics stemming from resistive currents and drag force on ions. The model successfully recovers the fluid force balance and continuity equations. These collisional effects on 2D potential mainly appear through the density profile changes, modifying the potential through electron pressure gradient. This means an accurate prescription of electron density and temperature profiles is important in predicting the potential structure in the FRC SOL. The Debye sheath potential and the potential profiles applied at the boundaries can be additional factors contributing to the 2D variations in SOL. This comprehensive full-f scheme holds promise for future investigations into turbulent transport in the presence of the self-consistent 2D potential together with the non-Maxwellian distributions and open boundary conditions in the FRC SOL.

Physics↗

Towards fully predictive gyrokinetic full- f simulations: validation and triangularity studies in TCV

Designing economical magnetic confinement fusion power plants motivates computational tools that can estimate plasma behavior from engineering parameters without direct reliance on experimental measurement of the plasma profiles. In this work, we present full-f global long-wavelength gyrokinetic simulations of edge and scrape-off layer turbulence in tokamaks that use only magnetic geometry, heating power, and particle inventory as inputs. Unlike many modeling approaches that employ free parameters fitted to experimental data, raising uncertainties when extrapolating to reactor scales. This approach directly simulates turbulence and resulting profiles through gyrokinetics without such empirical adjustments. This is achieved via an adaptive sourcing algorithm in Gkeyll that strictly controls energy injection and emulates particle sourcing due to neutral recycling. We show that the simulated kinetic profiles compare reasonably well with Thomson scattering and Langmuir probe data for Tokamak á Configuration Variable (TCV) discharge #65125, and that the simulations reproduce characteristic features such as blob transport and self-organized electric fields. Applying the same framework to study triangularity effects suggests mechanisms contributing to the improved confinement reported for negative triangularity (NT). Simulations of TCV discharges #65125 and #65130 indicate that NT increases the E x B flow shear (by about 20% in these cases), which correlates with reduced turbulent losses and a modest change in the distribution of power exhaust to the vessel wall. While the physical models contain approximations that can be refined in future work, the predictive capability demonstrated here, evolving multiple profile relaxation times with kinetic electron and ion models in hundreds of GPU hours, indicates the feasibility of using Gkeyll to support design studies of fusion devices.

Hoffmann, Antoine Cyril David [Princeton Plasma Ph↗

Heliostat optical error inspection with polarimetric imaging drone

On a Concentrated Solar Power (CSP) field, optical errors have significant impacts on the collection efficiency of heliostats. Fast, cost-effective, labor-efficient, and non-intrusive autonomous field inspection remains a challenge. Approaches using imaging drone, i.e., Unmanned Aerial Vehicle (UAV) system integrated with high resolution visible imaging sensors, have been developed to address these challenges; however, these approaches are often limited by insufficient imaging contrast. Here, in this study, we report a polarimetry-based method with a polarization imaging system integrated on UAV to enhance imaging contrast for in-situ detection of heliostat mirrors without interrupting field operation. We developed an optical model for skylight polarization pattern to simulate the polarization images of heliostat mirrors and obtained optimized waypoints for polarimetric imaging drone flight path to capture images with enhanced contrast. The polarimetric imaging-based method improved the success rate of edge detections in scenarios which were challenging for mirror edge detection with conventional imaging sensors. We have performed field tests to achieve significantly enhanced heliostat edge detection success rate and investigate the feasibility of integrating polarimetric imaging method with existing imaging-based heliostat inspection methods, i.e., Polarimetric Imaging Heliostat Inspection Method (PIHIM). Our preliminary field test results suggest that the PIHIM hold the promise to enable sufficient imaging contrast for real-time autonomous imaging and detection of heliostat field, thus suitable for non-interruptive fast CSP field inspection during its operation.

CSP Field↗

Nanoparticle O–H Bond Dissociation Free Energies from Equilibrium Measurements of Cerium Oxide Colloids

A novel equilibrium strategy for measuring the hydrogen atom affinity of colloidal metal oxide nanoparticles is presented. Reactions between oleate-capped cerium oxide nanoparticle colloids (nanoceria) and organic proton-coupled electron transfer (PCET) reagents are used as a model system. Nanoceria redox changes, or hydrogen loadings, and overall reaction stoichiometries were followed by both 1 H NMR and X-ray absorption near-edge spectroscopies. Furthermore, these investigations revealed that, in many cases, reactions between nanoceria and PCET reagents reach equilibrium states with good mass balance. Each equilibrium state is a direct measure of the bond strength, or bond dissociation free energy (BDFE), between nanoceria and hydrogen. Further studies, including those with larger nanoceria, indicated that the relevant bond is a surface O–H. Thus, we have measured surface O–H BDFEs for nanoceria—the first experimental BDFEs for any nanoscale metal oxide. Remarkably, the measured CeO–H BDFEs span 13 kcal mol –1 (0.56 eV) with changes in the average redox state of the nanoceria colloid. Possible chemical models for this strong dependence are discussed. We propose that the tunability of ceria BDFEs may be important in explaining its effectiveness in catalysis. More generally, metal oxide BDFEs have been used as predictors of catalyst efficacy that, traditionally, have only been accessible by computational methods. These results provide important experimental benchmarks for metal oxide BDFEs and demonstrate that the concepts of molecular bond strength thermochemistry can be applied to nanoscale materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamics of rapidly spinning blob-filaments: Fluid theory with a parallel kinetic extension

Blob-filaments (or simply “blobs”) are coherent structures formed by turbulence and sustained by nonlinear processes in the edge and scrape-off layer (SOL) of tokamaks and other magnetically confined plasmas. The dynamics of these blob-filaments, in particular, their radial motion, can influence the scrape-off layer width and plasma interactions with both the divertor target and with the main chamber walls. Motivated by recent results from the XGC1 gyrokinetic simulation code reported on elsewhere [J. Cheng et al., Nucl. Fusion 63, 086015 (2023)], a theory of rapidly spinning blob-filaments has been developed for this work. The theory treats blob-filaments in the closed flux surface region or the region that is disconnected from sheaths in the SOL. It extends previous work by treating blob spin, arising from partially or fully adiabatic electrons, as the leading-order effect and retaining inertial (ion charge polarization) physics in next order. Spin helps to maintain blob coherency and affects the blob's propagation speed. Dipole charge polarization, treated perturbatively, gives rise to blob-filaments with relatively slow radial velocity, comparable to that observed in the simulations. The theory also treats the interaction of rapidly spinning blob-filaments with a zonal flow layer. It is shown analytically that the flow layer can act like a transport barrier for these structures. Finally, parallel electron kinetic effects are incorporated into the theory. Various asymptotic parameter regimes are discussed, and asymptotic expressions for the radial and poloidal motion of the blob-filaments are obtained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Wind Loading on Parabolic Trough Collectors: Wind and Structural Loads Measurements at an Operational Powerplant

Concentrated Solar Power (CSP) is a promising method for using solar power for electricity generation with thermal energy storage for industrial applications. Solar collectors constitute almost 1/3 of the total cost of the power plant. One of the primary drivers of unrealiability of these collectors is wind-driven loading of mirrors, support structures, and drives. To date, the design of the solar collector structures has relied on data from wind tunnels that do not adequately capture the dynamic effects observed at scale. NREL initiated a field measurement campaign at the operational Nevada Solar One (NSO) parabolic trough powerplant. At this plant, parabolic trough solar collectors track the sun from east to west in the course of a day and face varying wind loads depending on the wind properties and the angle of the troughs. The aim of the project is a detailed characterization of prevailing wind and turbulence conditions and resulting operational loads on parabolic troughs, providing insights into structural dynamic response, and generating a comprehensive wind-loading dataset for validating simulations of wind loading on collector structures. The measurements at NSO consist of sonic anemometers on masts at different heights to characterize the incoming flow and conditions at four trough rows at the edge of the trough field. In addition, a Doppler Lidar scans the horizontal plane above the troughs. The wind measurements at NSO have been continuously collecting data since October 2021 and are combined with structural load measurements that started in November 2022. The load measurements were installed on the same four outermost trough rows and include support structure bending moments, drive torque moments, dynamic accelerations of the spaceframe, mirror displacement, and tilt angles. Measurements are planned to continue until May 2023, providing a first-of-a-kind, high-resolution multi-month dataset of combined wind and load measurements. In this presentation, we show first results of the measurement campaign. Based on the measurements, we identified three main factors altering the flow over the parabolic troughs: Wind speed, wind direction, and the angle of the parabolic troughs. Most interactions between incoming wind and the trough field are observed when the wind blows perpendicular to the trough rows. In this case, the first rows experience the highest wind speed and block the downwind rows, creating conditions with decreased wind speed and enhanced turbulence within the trough field. Also, turbulent length scales are smaller after the first row. This leads to the highest static loads (bending and torque moments) at the first row but potentially increased dynamic loads within the field. We illustrate our findings with case studies focused on different wind conditions and will present fatigue analysis to highlight the impact of wind-driven loads on collector structures.

CSP collectors↗

Helical Edge States and Quantum Phase Transitions in Tetralayer Graphene

Helical conductors with spin-momentum locking are promising platforms for Majorana fermions. Here we report observation of two topologically distinct phases supporting helical edge states in charge neutral Bernal-stacked tetralayer graphene in Hall bar and Corbino geometries. As the magnetic field B ⊥ and out-of-plane displacement field D are varied, we observe a phase diagram consisting of an insulating phase and two metallic phases, with 0, 1, and 2 helical edge states, respectively. These phases are accounted for by a theoretical model that relates their conductance to spin-polarization plateaus. Transitions between them arise from a competition among interlayer hopping, electrostatic and exchange interaction energies. Finally, our work highlights the complex competing symmetries and the rich quantum phases in few-layer graphene.

36 MATERIALS SCIENCE↗