Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compression techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Propulsion simulation for magnetically suspended wind tunnel models

The feasibility of simulating propulsion-induced aerodynamic effects on scaled aircraft models in wind tunnels employing Magnetic Suspension and Balance Systems. The investigation concerned itself with techniques of generating exhaust jets of appropriate characteristics. The objectives were to: (1) define thrust and mass flow requirements of jets; (2) evaluate techniques for generating propulsive gas within volume limitations imposed by magnetically-suspended models; (3) conduct simple diagnostic experiments for techniques involving new concepts; and (4) recommend experiments for demonstration of propulsion simulation techniques. Various techniques of generating exhaust jets of appropriate characteristics were evaluated on scaled aircraft models in wind tunnels with MSBS. Four concepts of remotely-operated propulsion simulators were examined. Three conceptual designs involving innovative adaptation of convenient technologies (compressed gas cylinders, liquid, and solid propellants) were developed. The fourth innovative concept, namely, the laser-assisted thruster, which can potentially simulate both inlet and exhaust flows, was found to require very high power levels for small thrust levels.

Joshi, Prakash B.↗
NASA NTRS1992

Obtaining Patterns Of Holes In Directional Couplers

Technique enables reproduction of pattern of holes in hidden common wall of microwave directional coupler. Talcum-dusting procedure yields pattern of powder on adhesive tape showing sizes of distances between holes. Later, coupler cleaned with water or compressed air. Applicable to other equipment containing inaccessible holes in common wall between adjacent tubes.

Perez, Raul M.↗
NASA NTRS1993

Application of an unstructured grid flow solver to planes, trains and automobiles

Rampant, an unstructured flow solver developed at Fluent Inc., is used to compute three-dimensional, viscous, turbulent, compressible flow fields within complex solution domains. Rampant is an explicit, finite-volume flow solver capable of computing flow fields using either triangular (2d) or tetrahedral (3d) unstructured grids. Local time stepping, implicit residual smoothing, and multigrid techniques are used to accelerate the convergence of the explicit scheme. The paper describes the Rampant flow solver and presents flow field solutions about a plane, train, and automobile.

Spragle, Gregory S.↗
NASA NTRS1993

A study of eigenvalue sensitivity for hydrodynamic stability operators

The eigenvalue sensitivity for hydrodynamic stability operators is investigated. Classical matrix perturbation techniques as well as the concept of epsilon-pseudospectra are applied to show that parts of the spectrum are highly sensitive to small perturbations. Applications are drawn from incompressible plane Couette flow, trailing line vortex flow, and compressible Blasius boundary-layer flow. Parameter studies indicate a monotonically increasing effect of the Reynolds number on the sensitivity. The phenomenon of eigenvalue sensitivity is due to the nonnormality of the operators and their discrete matrix analogs and may be associated with large transient growth of the corresponding initial value problem.

Schmid, Peter J.↗
NASA NTRS1994

The simulation of a propulsive jet and force measurement using a magnetically suspended wind tunnel model

Models featuring the simulation of exhaust jets were developed for magnetic levitation in a wind tunnel. The exhaust gas was stored internally producing a discharge of sufficient duration to allow nominal steady state to be reached. The gas was stored in the form of compressed gas or a solid rocket propellant. Testing was performed with the levitated models although deficiencies prevented the detection of jet-induced aerodynamic effects. Difficulties with data reduction led to the development of a new force calibration technique, used in conjunction with an exhaust simulator and also in separate high incidence aerodynamic tests.

Garbutt, K. S.↗
NASA NTRS1992

A coupled Eulerian/Lagrangian method for the solution of three-dimensional vortical flows

A coupled Eulerian/Lagrangian method is presented for the reduction of numerical diffusion observed in solutions of three-dimensional rotational flows using standard Eulerian finite-volume time-marching procedures. A Lagrangian particle tracking method using particle markers is added to the Eulerian time-marching procedure and provides a correction of the Eulerian solution. In turn, the Eulerian solutions is used to integrate the Lagrangian state-vector along the particles trajectories. The Lagrangian correction technique does not require any a-priori information on the structure or position of the vortical regions. While the Eulerian solution ensures the conservation of mass and sets the pressure field, the particle markers, used as 'accuracy boosters,' take advantage of the accurate convection description of the Lagrangian solution and enhance the vorticity and entropy capturing capabilities of standard Eulerian finite-volume methods. The combined solution procedures is tested in several applications. The convection of a Lamb vortex in a straight channel is used as an unsteady compressible flow preservation test case. The other test cases concern steady incompressible flow calculations and include the preservation of turbulent inlet velocity profile, the swirling flow in a pipe, and the constant stagnation pressure flow and secondary flow calculations in bends. The last application deals with the external flow past a wing with emphasis on the trailing vortex solution. The improvement due to the addition of the Lagrangian correction technique is measured by comparison with analytical solutions when available or with Eulerian solutions on finer grids. The use of the combined Eulerian/Lagrangian scheme results in substantially lower grid resolution requirements than the standard Eulerian scheme for a given solution accuracy.

Felici, Helene Marie↗
DOE OSTI2020

Fully compressible simulations of waves and core convection in main-sequence stars

Context: Recent, nonlinear simulations of wave generation and propagation in full-star models have been carried out in the anelastic approximation using spectral methods. Although it makes long time steps possible, this approach excludes the physics of sound waves completely and requires rather high artificial viscosity and thermal diffusivity for numerical stability. A direct comparison with observations is thus limited. Aims: In this study, we explore the capabilities of our compressible multidimensional Seven-League Hydro (SLH) code to simulate stellar oscillations. Methods: We compare some fundamental properties of internal gravity and pressure waves in 2D SLH simulations to linear wave theory using two test cases: (1) an interval gravity wave packet in the Boussinesq limit and (2) a realistic 3 M ⊙ stellar model with a convective core and a radiative envelope. Oscillation properties of the stellar model are also discussed in the context of observations. Results: Our tests show that specialized low-Mach techniques are necessary when simulating oscillations in stellar interiors. Basic properties of internal gravity and pressure waves in our simulations are in good agreement with linear wave theory. As compared to anelastic simulations of the same stellar model, we can follow internal gravity waves of much lower frequencies. The temporal frequency spectra of velocity and temperature are flat and compatible with the observed spectra of massive stars. Conclusion: The low-Mach compressible approach to hydrodynamical simulations of stellar oscillations is promising. Our simulations are less dissipative and require less luminosity boosting than comparable spectral simulations. The fully-compressible approach allows for the coupling of gravity and pressure waves in the outer convective envelopes of evolved stars to be studied in the future.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Experimental Evaluation of Geopolymer, Nano-Modified, and Neat Class H Cement by Using Diametrically Compressive Tests

Abstract Cement is the prime barrier material to maintain zonal isolation during wellbore life-cycle. Different types of the cement have different performances on sealability. The primary objective of this study is evaluation of three types of cement systems, neat Class H, nano-synthetic graphite, and rock-based geopolymer cements, on interfacial bond integrity. Diametrical compressive tests are used on casing–cement–formation systems. Cement performances are tested in a conventional configuration (Berea Sandstone). A universal testing system is utilized to analyze the relationship applied load–axial strain and the digital image correlation (DIC) technique is used to generate the strain field maps. Based on the relationship and DIC results, bond strengths in different cement systems are evaluated. Additionally, microscope images provide insight explanations of the bond from micro-view. Based on the experimental results, failures of all cases initiate and propagate from the casing–cement interface. Then, radial cracks develop through the formation. This is because the mechanical interlocking bonds are formed only at the cement–sandstone interface to enhance the bond strength. The comparison of geopolymer and nano-modified cements with the conventional cement (neat Class H) shows that the unconventional cements have a lower maximum load and higher axial strain before failure of the samples. It indicates that both the two kinds of cements are more ductile than conventional cement and can support more deformation before the initiation of cracks.

Energy & Fuels↗
DOE OSTI2021

Characterization of Polyhydroxybutyrate-Based Composites Prepared by Injection Molding

The waste generated by single-use plastics is often non-recyclable and non-biodegradable, inevitably ending up in our landfills, ecosystems, and food chain. Through the introduction of biodegradable polymers as substitutes for common plastics, we can decrease our impact on the planet. In this study, we evaluate the changes in mechanical and thermal properties of polyhydroxybutyrate-based composites with various additives: Microspheres, carbon fibers or polyethylene glycol (2000, 10,000, and 20,000 MW). The mixtures were injection molded using an in-house mold attached to a commercial extruder. The resulting samples were characterized using microscopy and a series of spectroscopic, thermal, and mechanical techniques. We have shown that the addition of carbon fibers and microspheres had minimal impact on thermal stability, whereas polyethylene glycol showed slight improvements at higher molecular weights. All of the composite samples showed a decrease in hardness and compressibility. The findings described in this study will improve our understanding of polyhydroxybutyrate-based composites prepared by injection molding, enabling advancements in integrating biodegradable plastics into everyday products.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Extended record length of atmospheric data gathered via Nimbus-6

A low-power nonvolatile data memory unit was developed for free floating balloons in the TWERL experiment. By means of multiple identification codes data records, several hours long, could be transferred in compressed form to the Nimbus-6 satellite for retransmission to ground stations. Eight of these units were flown on constant density balloons to investigate atmospheric wave motions throughout the Southern Hemisphere. One returned valid data for ten months. Similar techniques could be used with other types of observing platforms.

Afanasjevs, J.↗
NASA NTRS1979

The solution of the three-dimensional viscous-compressible Navier-Stokes equations on a vector computer

The development of a vectorized computer code for the solution of the three-dimensional viscous-compressible Navier-Stokes equations is described. The code is applied on the CDC STAR-100 vector computer which is capable of achieving high result rates when a high degree of parallelism is present in the computations. The computational technique is an explicit time-split MacCormack predictor-corrector algorithm. Since a large volume of data is processed and virtual memory utilized, a data management scheme based on interleaving is used. The program has been applied to obtain the solution of the laminar supersonic flow about a family of three-dimensional corners. The equations of motion are expressed in a generalized form relative to a uniform rectangular computational domain. The metric coefficient and boundary conditions must be supplied for the corresponding physical domain. For calculations with 30,000 grid points, a computational rate of 0.00015 seconds per grid point per time step is observed.

Smith, R. E.↗
NASA NTRS1987

Hypersonic propulsion research

The NASA Langley Research Center has conducted hypersonic propulsion research since the 1960s. A variety of inlet concepts were explored and characterized. The emphasis of the inlet program was the development of the short (light weight), fixed geometry, side-wall-compression inlets that operate efficiently over a wide Mach number range. As hypersonic combustion tunnels were developed, programs to study the parameters controlling fuel mixing and combustion with single and multiple strut models were conducted using direct connect test techniques. These various tests supported the design of subscale engine test hardware that integrated inlet and combustor technology and allowed the study of the effect of heat release on thrust and combustor/inlet interaction. A number of subscale engine tests have demonstrated predicted performance levels at Mach 4 and 7 simulated flight conditions.

Northam, G. Burton↗
NASA NTRS1989

Finite element formulations for compressible flows

Researchers started their studies on the development and application of computational methods for compressible flows. Particular attention was given to proper numerical treatment of sharp layers occurring in such problems and to general mesh generation capabilities for intricate computational geometries. Mainly finite element methods enhanced with several state-of-the art techniques (such as the streamline-upwind/Petrov-Galerkin, discontinuity capturing, adaptive implicit-explicit, and trouped element-by-element approximate factorization schemes) were employed.

Tezduyar, Tayfun E.↗
NASA NTRS1991

Enhancement of the no-vent fill process

This paper presents an analytical and experimental evaluation of an enhanced techniques for no-vent fill. The method entails injecting liquid through the top of the receiver vessel, thereby increasing surface area and agitation of the ullage/liquid interface. Both of these factors promote condensation induced ullage collapse, and reduce compressive impedance to the incoming liquid. The enhanced process was analyzed by modifying the surface area algorithm of an existing tank thermodynamic code to model a downward-pointing, conical jet impringing on a steadily rising liquid surface. Transient pressure and temperature measurements from several tests with Freon-114 were input into the revised model to calculate condensation rate as a function of fill level. By expressing these rates in dimensionless form (i.e., in terms of Stanton number and Prandtl number), an empirical correlation similar to the submerged jet model of Brown and Sonin (1989) was derived. This provided a basis for developing an expression which relates top fill to bottom fill performance.

Vaughan, David A.↗
NASA NTRS1990

Hypersonic propulsion research

The development of technology for the modular airframe integrated scramjet has been the focus of hypersonic propulsion research for several years. An part of this research, a variety of inlet concepts have been explored and characterized. The emphasis of the inlet program has been the development of the short (light weight), fixed geometry, side wall compression inlets that operate efficiently over a wide Mach number range. As hypersonic combustion tunnels were developed, programs to study the parameters controlling fuel mixing and combustion with single and multiple strut models were conducted using direct connect test techniques. These various tests supported the design of subscale engine test hardware that integrated inlet and combustor technology and allowed the study of the effect of heat release on thrust and combustor/inlet interaction. A number of subscale engine tests have shown predicted performance levels at Mach 4 and 7 simulated flight conditions. A few of the highlights from this research program are summarized.

Northam, G. Burton↗
NASA NTRS1992

Vector quantization for volume rendering

Volume rendering techniques typically process volumetric data in raw, uncompressed form. As algorithmic and architectural advances improve rendering speeds, however, larger data sets will be evaluated requiring consideration of data storage and transmission issues. In this paper, we analyze the data compression requirements for volume rendering applications and present a solution based on vector quantization. The proposed system compresses volumetric data and then renders images directly from the new data format. Tests on a fluid flow data set demonstrate that good image quality may be achieved at a compression ratio of 17:1 with only a 5 percent cost in additional rendering time.

Ning, Paul↗
NASA NTRS2003

Measurement of the Specific Heat Using a Gravity Cancellation Approach

The specific heat at constant volume C(sob V) of a simple fluid diverges near its liquid-vapor critical point. However, gravity-induced density stratification due to the divergence of isothermal susceptibility hinders the direct comparison of the experimental data with the predictions of renormalization group theory. In the past, a microgravity environment has been considered essential to eliminate the density stratification. We propose to perform specific heat measurements of He-3 on the ground using a method to cancel the density stratification. A He-3 fluid layer will be heated from below, using the thermal expansion of the fluid to cancel the hydrostatic compression. A 6% density stratification at a reduced temperature of 10(exp -5) can be cancelled to better than 0.1% with a steady 1.7 micro K temperature difference across a 0.05 cm thick fluid layer. A conventional AC calorimetry technique will be used to determine the heat capacity. The minimized bulk density stratification with a relaxation time 6500 sec at a reduced temperature of 10(exp -5) will stay unchanged during 1 Hz AC heating. The smear of the specific heat divergence due to the temperature difference across the cell is about 0.1% at a reduced temperature of 10(exp -6). The combination of using High Resolution Thermometry with a 0.5 n K temperature resolution in the AC technique and the cancellation of the density stratification will enable C(sub V) to be measured down to a reduced temperature of 10(exp -6) with less than a 1% systematic error.

Zhong, Fang↗