Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aqueous processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Simulating adsorption of U(VI) under transient groundwater flow and hydrochemistry – Physical versus non-equilibrium model

Coupled intra-grain diffusional mass-transfer and non-linear surface complexation processes play an important role for the transport behaviour of U(VI) in contaminated aquifers. Two alternative model approaches for simulating these coupled processes have been analysed and compared: (i) the physical non-equilibrium approach that explicitly accounts for aqueous speciation and instantaneous surface complexation reactions in the intra-grain regions and approximates the diffusive mass exchange between the immobile intra-grain pore water and the advective pore water as multi-rate 1st-order mass transfer and (ii) the chemical non-equilibrium approach that approximates the diffusion-limited intra-grain surface complexation reactions by a set of multiple 1st-order surface complexation reaction kinetics, thereby eliminating the explicit treatment of aqueous speciation in the intra grain pore water. Model comparison has been carried out for column and field scale scenarios, representing the highly transient hydrological and geochemical conditions in the U(VI)-contaminated aquifer at the Hanford 300A site, Washington, USA. It was found that the response of apparent U(VI) adsorption/desorption kinetic behaviour to hydrogeochemically induced changes in U(VI) sorption strength is more pronounced in the physical than in the chemical non-equilibrium model. The magnitude of the differences in model behaviour depends particularly on the degree of disequilibrium between the advective and immobile phase U(VI) concentrations. While a clear difference in U(VI) transport behaviour between the two models was noticeable for the column-scale scenarios, only minor differences were found for the Hanford 300A field scale scenarios, where the model-generated disequilibrium conditions were less pronounced as a result of high frequent groundwater flow reversals.

54 ENVIRONMENTAL SCIENCES↗

Evolution of microscopic heterogeneity and dynamics in choline chloride-based deep eutectic solvents

Deep eutectic solvents (DESs) are an emerging class of non-aqueous solvents that are potentially scalable, easy to prepare and functionalize for many applications ranging from biomass processing to energy storage technologies. Predictive understanding of the fundamental correlations between local structure and macroscopic properties is needed to exploit the large design space and tunability of DESs for specific applications. Here, we employ a range of computational and experimental techniques that span length-scales from molecular to macroscopic and timescales from picoseconds to seconds to study the evolution of structure and dynamics in model DESs, namely Glyceline and Ethaline, starting from the parent compounds. We show that systematic addition of choline chloride leads to microscopic heterogeneities that alter the primary structural relaxation in glycerol and ethylene glycol and result in new dynamic modes that are strongly correlated to the macroscopic properties of the DES formed.

36 MATERIALS SCIENCE↗

ECO2M: A TOUGH2 Fluid Property Module for Mixtures of Water, NaCl, and CO2, Including Super- and Sub-Critical Conditions, and Phase Change Between Liquid and Gaseous CO2

ECO2M is a fluid property module for the TOUGH2 simulator (Version 2.0) that was designed for applications to geologic storage of CO{sub 2} in saline aquifers. It includes a comprehensive description of the thermodynamics and thermophysical properties of H{sub 2}O - NaCl - CO{sub 2} mixtures, that reproduces fluid properties largely within experimental error for temperature, pressure and salinity conditions in the range of 10 C {le} T {le} 110 C, P {le} 600 bar, and salinity from zero up to full halite saturation. The fluid property correlations used in ECO2M are identical to the earlier ECO2N fluid property package, but whereas ECO2N could represent only a single CO{sub 2}-rich phase, ECO2M can describe all possible phase conditions for brine-CO{sub 2} mixtures, including transitions between super- and sub-critical conditions, and phase change between liquid and gaseous CO{sub 2}. This allows for seamless modeling of CO{sub 2} storage and leakage. Flow processes can be modeled isothermally or non-isothermally, and phase conditions represented may include a single (aqueous or CO{sub 2}-rich) phase, as well as two-and three-phase mixtures of aqueous, liquid CO{sub 2} and gaseous CO{sub 2} phases. Fluid phases may appear or disappear in the course of a simulation, and solid salt may precipitate or dissolve. TOUGH2/ECO2M is upwardly compatible with ECO2N and accepts ECO2N-style inputs. This report gives technical specifications of ECO2M and includes instructions for preparing input data. Code applications are illustrated by means of several sample problems, including problems that had been previously solved with TOUGH2/ECO2N.

54 ENVIRONMENTAL SCIENCES↗

ECO2N V. 2.0: A New TOUGH2 Fluid Property Module for Mixtures of Water, NaCl, and CO 2

ECO2N V2.0 is a fluid property module for the TOUGH2 simulator (Version 2.1) that was designed for applications to geologic sequestration of CO 2 in saline aquifers and enhanced geothermal reservoirs. ECO2N V2.0 is an enhanced version of the previous ECO2N V1.0 module (Pruess, 2005). It expands the temperature range up to about 300°C whereas V1.0 can only be used for temperatures below about 110°C. V2.0 includes a comprehensive description of the thermodynamics and thermophysical properties of H 2 O - NaCl -CO 2 mixtures, that reproduces fluid properties largely within experimental error for the temperature, pressure and salinity conditions of interest (10 °C < T < 300 °C; P < 600 bar; salinity up to halite saturation). This includes density, viscosity, and specific enthalpy of fluid phases as functions of temperature, pressure, and composition, as well as partitioning of mass components H 2 O, NaCl and CO 2 among the different phases. In particular, V2.0 accounts for the effects of water on the thermophysical properties of the CO 2 -rich phase, which was ignored in V1.0, using a model consistent with the solubility models developed by Spycher and Pruess (2005, 2010). In terms of solubility models, V2.0 uses the same model for partitioning of mass components among the different phases (Spycher and Pruess, 2005) as V1.0 for the low temperature range (<99°C) but uses a new model (Spycher and Pruess, 2010) for the high temperature range (>109°C). In the transition range (99-109°C), a smooth interpolation is applied to estimate the partitioning as a function of the temperature. Flow processes can be modeled isothermally or non-isothermally, and phase conditions represented may include a single (aqueous or CO 2 -rich) phase, as well as two-phase mixtures. Fluid phases may appear or disappear in the course of a simulation, and solid salt may precipitate or dissolve. This report gives technical specifications of ECO2N V2.0 and includes instructions for preparing input data

15 GEOTHERMAL ENERGY↗

Compositional studies of primitive asteroids

Primitive asteroids in the solar system (C, P, D class and associated subclasses) are believed to have undergone less thermal processing compared with the differential (S class) asteroids. Telescopic spectra of C class asteroids show effects of aqueous alteration products produced when heating of the asteroids was sufficient to melt surface water, but not strong enough to produce differentiation. Spectrum analysis of P and D class asteroids suggests that aqueous alteration terminated in the outer belt and did not operate at the distance of Jupiter's orbit.

Vilas, Faith↗

Optical diagnostics of solution crystal growth

Solution crystal growth monitoring of LAP/TGS crystals by various optical diagnostics systems, such as conventional and Mach-Zehnder (M-Z) interferometers, optical heterodyne technique, and ellipsometry, is under development. The study of the dynamics of the crystal growth process requires a detailed knowledge of crystal growth rate and the concentration gradient near growing crystals in aqueous solution. Crystal growth rate can be measured using conventional interferometry. Laser beam reflections from the crystal front as well as the back surface interfere with each other, and the fringe shift due to the growing crystal yields information about the growth rate. Our preliminary results indicate a growth rate of 6 A/sec for LAP crystals grown from solution. Single wavelength M-Z interferometry is in use to calculate the concentration gradient near the crystal. Preliminary investigation is in progress using an M-Z interferometer with 2 cm beam diameter to cover the front region of the growing crystal. In the optical heterodyne technique, phase difference between two rf signals (250 KHZ) is measured of which one is a reference signal, and the other growth signal, whose phase changes due to a change in path length as the material grows. From the phase difference the growth rate can also be calculated. Our preliminary results indicate a growth rate of 1.5 A/sec. the seed and solution temperatures were 26.46 C and 27.92 C respectively, and the solution was saturated at 29.0 C. an ellipsometer to measure the growth rate and interface layer is on order from JOBIN YVON, France. All these systems are arranged in such a manner that measurements can be made either sequentially or simultaneously. These techniques will be adapted for flight experiment.

Kim, Yongkee↗

The SNC Meteorites Are From Mars

The thirteen SNC meteorites are all igneous rocks, either basalts or basaltic cumulates. They are inferred to be from Mars, based on direct comparison with martian materials and on consistency with inferences about Mars. Most telling is that the SNC meteorites contain traces of gas which is very similar in elemental and isotopic compositions to the modem Martian atmosphere as measured by Viking. The martian atmosphere appears to be unique in the solar system, so its presence in the SNCs is accepted as virtually unequivocal proof that they formed on Mars. Independent of this link, the SNC meteorites must be from a planet with a significant atmosphere because they contain several abundant gas components, some of which carry large isotopic fractionations characteristic of atmospheric processing. The chemical compositions of the SNC meteorites are also consistent with data from in situ analyses of martian soils and rocks, and are quite different from compositions of other meteorites, rocks from the Earth, and rocks from the Moon. The range of formation ages for the SNC meteorites, 4.5 Ga to 0. 18 Ga, is consistent with the varied ages of the Martian surface (based on its cratering record) and inconsistent with surface ages on any other solar system body. The extreme chemical fractionations in the SNC meteorites suggest complex internal processes on a large planet, which is inconsistent with an asteroidal origin. Some SNCs were altered by aqueous solutions at greater than 0.7 Ga, consistent with the recent presence of liquid groundwater in Mars inferred independently from the geology of its surface. There seems little likelihood that the SNCs are not from Mars. If they were from another planetary body, it would have to be substantially identical to Mars as it now is understood.

Treiman, Allan H.↗

Polymerization on the rocks: theoretical introduction

It is difficult if not impossible to synthesize long polymers of amino acids, nucleotides, etc., in homogeneous aqueous solution. We suggest that long polymers were synthesized on the surface of minerals in a prebiotic process analogous to solid-phase synthesis. Provided that the affinity of a mineral for an oligomer increases with the length of the oligomer, adsorption must become essentially irreversible for sufficiently long oligomers. Irreversibly adsorbed oligomers may be elongated indefinitely by repeated cycles in which the mineral with its adsorbed oligomers is first incubated with activated monomers and then washed free of deactivated monomer and side-products. We discuss in some detail the formation of oligomers of negatively-charged amino acids such as glutamic acid on anion-exchange minerals such as hydroxylapatite or illite. We show that the average length of adsorbed oligomers at steady state, n, depends on the balance between the rate of chain elongation and the rate of hydrolysis, and we derive a very approximate formula for n.

NASA Discipline Exobiology↗

Diagenesis in the Murray Formation, Gale Crater, Mars

The Mars Science Laboratory (MSL) Curiosity rover began investigating the rocks of Mt. Sharp in September 2014. The Murray formation is the lowermost unit, which is mostly comprised of finely laminated mudstones, suggesting these sediments were deposited in a lacustrine environment. It is important to characterize the geochemical and mineralogical trends throughout the Murray Fm to interpret the aqueous conditions of the ancient lake, the sources of the lake sediments, and post-depositional alteration processes. Four samples have been drilled from the Murray Fm so far: Confidence Hills, Mojave 2, and Telegraph Peak were collected from the Pahrump Hills member - the basal portion of the Murray Fm, and Buckskin was collected in the Marias Pass region (Fig. 1). The drill fines were delivered to the instruments inside the rover, including the CheMin instrument, a combination X-ray diffractometer and X-ray fluorescence spectrometer. Rietveld refinements and FULLPAT analyses of 1D CheMin XRD patterns were performed to determine quantitative abundances of minerals and amor-phous phases and the unit cell parameters of minerals present in abundances greater than 4-5 wt.%.

Rampe, E. B.↗

Update on Measurement of the Composition of Ryugu Fluid Inclusions

Imaging using X-ray absorption contrast by synchrotron nano-computed tomography of a Ryugu pyrrhotite crystal (C0002-FC012 - from the second Hayabusa2 spacecraft touch-down site) revealed probable fluid inclusions in the center of a crystal of pyrrhotite, suggesting the parent fluids were trapped in the early stages of crystal growth on Ryugu’s parent asteroid. We previously described the performance of Time-of Flight-Secondary Ion Mass Spectrometry (TOF-SIMS) depth profiling and high-resolution mapping at -120°C to expose and measure the composition of the trapped fluids in a frozen state in two Ryugu inclusions [1,2]. Here we report results from follow-on measurements of additional inclusions in the same pyrrhotite crystal, and the initial results of measurement of standards. The ultimate goal is to reveal the quantitative composition of the fluids that caused aqueous alteration, in particular the H2O:CO2 ratio, which will also facilitate cosmochemical modeling of the alteration process.

M Zolensky↗

Liquefaction processes and systems and liquefaction process intermediate compositions

Liquefaction processes are provided that can include: providing a biomass slurry solution having a temperature of at least 300.degree. C. at a pressure of at least 2000 psig; cooling the solution to a temperature of less than 150.degree. C.; and depressurizing the solution to release carbon dioxide from the solution and form at least part of a bio-oil foam. Liquefaction processes are also provided that can include: filtering the biomass slurry to remove particulates; and cooling and depressurizing the filtered solution to form the bio-oil foam. Liquefaction systems are provided that can include: a heated biomass slurry reaction zone maintained above 300.degree. C. and at least 2000 psig and in continuous fluid communication with a flash cooling/depressurization zone maintained below 150.degree. C. and between about 125 psig and about atmospheric pressure. Liquefaction systems are also provided that can include a foam/liquid separation system. Liquefaction process intermediate compositions are provided that can include a bio-oil foam phase separated from an aqueous biomass solids solution.

09 BIOMASS FUELS↗

Adsorption Efficiency of Polyaspartate-Montmorillonite Composite Towards the Removal of Pb(II) and Cd(II) from Aqueous Solution

The selective modification of sodium montmorillonite (Na{sup +}-Mt) surface with polyionene followed by poly (succinimde-co-aspartate) has been considered. Na{sup +}-Mt was allowed to react with well characterized polyionene in two fold excess. The resulting polyionene/Mt (IC) was further modified with poly (succinimide-co-aspartate) through an ion exchange process. The obtained polyaspartate/Mt (IPS) composite was characterized by elemental analysis, X-ray diffraction, FTIR spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and BET surface analyzer. The adsorption efficiency of IPS composite was investigated for the removal of Pb(II) and Cd(II) from aqueous solution under different experimental conditions including initial metal ions concentration, temperature and single and binary mixture systems of metal ions. The experimental data were analyzed by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models. Langmuir model reveals that the monolayer adsorption capacity of IPS was 92.59 and 67.57 mg/g for Pb(II) and Cd(II), respectively. The modification of parent Na{sup +}-Mt enhanced their adsorption capacity by about 87.91 and 29.84% for Pb(II) and Cd(II), respectively, due to inclusion of extra active sites of polyaspartate. The mean sorption energy, E calculated from Dubinin–Radushkevich isotherm were 2.75 and 1.98 kJ/mol for the adsorption of Pb(II) and Cd(II), respectively, indicating physical adsorption process. Also, The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic process. The mechanism of cation exchange and complexation of metal ions was suggested. IPS composite has a considerable potential for the removal of heavy metal ions from aqueous solution and wastewater stream.

36 MATERIALS SCIENCE↗

A Novel Eco-Biosorbent for Decontamination of Hazardous Dye from Aqueous Medium

A novel multi-component biosorbent consisted of pine, oak, hornbeam and fir sawdust biomasses was used to eliminate a common hazardous dye (Malachite green, MG) from aqueous solution. The influences of different parameters like solution pH, biosorbent amount, dye concentration and contact time on the removal process were thoroughly studied to evaluate optimum biosorption conditions. The pseudo-first-order, pseudo-second-order, Elovich, logistic and intra-particle diffusion models were used to describe the biosorption kinetics. Logistic model represented the kinetic experimental data well. The experimental equilibrium biosorption data were analyzed by Freundlich, Langmuir and Dubinin–Radushkevich isotherms. Freundlich model fitted better with the experimental data compared to others. In addition, the mean free energy obtained from Dubinin–Radushkevich model and the standard Gibbs free energy change indicated that the nature of biosorption was feasible, spontaneous and physical type. Overall, the novel eco-biosorbent could be used as a promising biosorbent to remove such unsafe dye molecules from aqueous environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-Sourced Collaboration for the Production and Refining of Rare Elements and Critical Metals (Final Technical Report)

The project objective was to develop a feasible and cost-effective method for recovering rare earth elements (REEs) and critical materials (CMs) from coal and coal byproducts, resulting in high-purity individually separated REEs and CMs. The targeted REEs included Y, Pr, Nd, Gd, Dy, and Sm, with a purity of over 99.5%, while the CMs included Co, Mn, Ga, Sr, Li, Ni, Zn, and Ge, with a purity of over 90%. The project aimed to design a prototype facility capable of producing 1-3 tonnes/day of high-purity REO mixes. The work was divided into four designated circuits: 1) REE extraction and concentration, 2) REE separation and purification, 3) RE metal production, and 4) CM production. To achieve these goals, the project involved 11 tasks, including technology reviews, research, process flow diagram development, mass balance estimation, and preliminary technical-economic analysis. The project team included researchers from the University of Kentucky, University of Alabama and Virginia Tech as well as process specialists from Argonne National Laboratory. MP Materials provided technical support regarding rare earth markets and processing while Alliance Coal performed resource assessment. The project included a market analysis for Nd/Pr, Tb, Dy, Gd, Y, Co, Mn, Li, Sr, Ga, Ni, Zn, and Ge. These analyses provided insights into the supply and demand trends as well as historic and future projections of market price relative to purity requirements for these elements. Two coal resources were selected for the project: the West Kentucky No. 13 (Baker) Seam and an undisclosed lignite resource in the Illinois coal basin. The estimated quantities of REEs in these resources were calculated based on production samples and drilling data. It was estimated that there is adequate supply for an operation producing one metric ton daily of higher purity mixed rare earth oxides (MREO) for approximately 20 years at a site located in western Kentucky. In Circuit 1, project data was obtained from a pilot heap leach and REE concentration facility. It was concluded that the existing circuit, which generated a MREO concentrate, two types of CM mixed products, and Li- and Sr-containing waters, would be suitable feed for circuits 2-4. Data from the first-of-its-kind coal coarse refuse heap leach pilot pad played a crucial role in estimating reliable elemental concentrations of the pregnant leaching solution (PLS). The average total REE concentration in the PLS was found to be 28.6 ppm. In Circuit 2, several concepts were explored including a novel process referred to as solvent-assisted chromatography (SAC). This concept involved a novel columnar reactor that incorporated multiple mixer/settlers, thereby enabling the operation of counter-flowing aqueous and organic phases. Unfortunately, due to project time constraints, a complete fundamental modeling analysis could not be completed to fully evaluate the technology. Molten salt electrowinning was considered as an alternative for circuit 3 following circuit 2 purification circuit utilizing the novel SAC process. A mass and energy balance of Nd reduction to metal in a fluoride containing molten salt electrolyte was conducted. Comparisons were made with the current state of Asian molten salt electrorefining, and potential improvements in siphoning rare earth metals (REM) from the reactor were presented. A cost estimate was performed for the production of 1 tonne per day, which yielded a total of $2.29 million for the nine electrowinning (EW) cells required. The selected option for circuits 2 and 3 was a plasma distillation process, which initially separates rare earth elements (REEs) from other elements. This is followed by selective electrowinning in various ionic liquids. The selection was made on the basis of thermodynamic modeling and experimental data previously published by a project partner. The combination offers an innovative approach to integrated refining and RE metal production. For Circuit 4, an extensive literature review was conducted for the processing of the CMs. The ultimate decision was to utilize a combined plasma and ionic liquid process as well to produce individual high-purity concentrates of Zn, Ni, Co, Mn, and Mg. A separate flowsheet for Li and Sr was recommended, which would yield carbonates of these elements. Due to the lack of suitable experimental data at this time, a process recommendation could not be provided but several methods have been proposed for consideration. Lastly, a techno-economic analysis (TEA) was conducted to assess the effectiveness of the proposed process for further investigation. The TEA results revealed a capital expense (CapEx) of $737 million and an annual operational expense (OpEx) of $220 million. Due to the selected elements, the hypothetical heap leach pad can produce 1 metric tonne per day of REO equivalent, but a conscious decision was made to only treat targeted REEs, resulting in the production of 0.4 metric tonne of REM. An estimated annual revenue of $90.87 million was projected based on standard market pricing information provided by the funding agency. During the TEA, ten different modules were evaluated for costing purposes. The precipitation circuit was identified as the largest single operational expense, followed by the Mg/Mn process due to the amount of treated metal. In terms of capital expenditures, the heap leach process incurred the highest cost, followed by the Mg/Mn process. The scalability of the plasma process is a crucial consideration since the reactors cannot be scaled beyond the largest demonstrated size due to their reliance on surface area of the slag and vapor phase. The purity estimate for the REEs are generally 98%±2% to produce a metal. The purity level being lower than the project objective was due to the lack of specific experimental data needed to tighten the tolerance of the estimates. Based on literature and previous experience, the CMs are estimated as follows; Ga (95%+, metal), Sr (95%+, carbonate), Li (95%+, carbonate), Ni (98%±2%, metal), Zn (95%+, metal sponge), Ge (95%+, metal), Co (98%±2%, metal), and Mn (98%±2%, metal).

01 COAL, LIGNITE, AND PEAT↗

Potential-specific structure at the hematite-electrolyte interface

The atomic-scale structure of interfaces between metal oxides and aqueous electrolytes controls their catalytic, geochemical, and corrosion behavior. Measurements that probe these interfaces in situ provide important details of ion and solvent arrangements, but atomically precise structural models do not exist for common oxide-electrolyte interfaces far from equilibrium. Using a novel cell, we measured the structure of the hematite (a-Fe 2 O 3 ) (110$\bar{2}$)-electrolyte interface under controlled electrochemical bias using synchrotron crystal truncation rod X ray scattering. At increasingly cathodic potentials, charge-compensating protonation of surface oxygen groups increases the coverage of specifically bound water while adjacent water layers displace outwardly and became disordered. Returning to open circuit potential leaves the surface in a persistent metastable protonation state. The flux of current and ions at applied potential is thus regulated by a unique interfacial electrolyte environment, suggesting that electrical double layer models should be adapted to the dynamically changing interfacial structure far from equilibrium.

electrochemistry↗

Electrochemical chlor-iron process for iron production from iron oxide and salt water

The iron and steel industry accounts for ~8% of global greenhouse gas emissions. Electrochemical reduction of iron ore to metal for electric arc furnaces can enable sustainable steel production, but existing electrochemical processes require expensive capital or electrolytes. Here we report a low-temperature, electrochemical cell that consumes low-cost and abundant iron oxide and aqueous sodium chloride, while co-producing sodium hydroxide and chlorine. Industrially relevant current densities and Faradaic efficiencies for iron production were demonstrated, with 94% selectivity to iron metal at an applied current density of 200 mA cm –2 . Freestanding films of phase-pure iron were formed after 4h of continuous, stable electrolysis. The process can lead to levelized costs of iron that are competitive with iron produced in fossil-fuel-powered blast furnaces, and the co-produced sodium hydroxide can be used for CO 2 capture from the air or ocean, creating a net-negative-emission process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Continuous Flow Fabrication of Block Copolymer-Grafted Silica Micro-Particles in Environmentally Friendly Water/Ethanol Media

Polymer-grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface-initiated controlled radical polymerization (SI-CRP) is the most feasible method to fabricate PGIPs. However, a conventional in-batch reaction still suffers from several disadvantages, including time-consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)-b-poly(N-isopropylacrylamide) (PNIPAM)–grafted silica micro-particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI-CRP can be accomplished sequentially in a continuous flow system, avoiding multi-step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (&ETH; < 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in-batch reaction at the same condition, the continuous system also suppresses possible gelation problems.

36 MATERIALS SCIENCE↗