SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Slides for a presentation discussing the history of the Nevada Proving Ground, the above-ground nuclear testing that occurred there, and the effects of that testing on the public near the testing grounds.
LANL’s Test Engineering group continuously pursues research and development in structural dynamics to improve shock and vibration testing capabilities, processes, and analysis techniques to increase the fidelity of service environment recreations in laboratory testing settings.
The era of atmospheric testing defies a simple description. Beginning with the goal of proving fission, the United States’ test program grew in complexity as scientists explored thermonuclear reactions, met the military demand for a variety of weapons for an increasing number of delivery platforms, and reacted to the ever-growing public fear of fallout. And, of course, political considerations were always present, first in the prosecution of World War II and later in the Cold War. To understand the atmospheric test program, then, is to understand how science, politics, and the public shaped our society in ways that are still difficult to fully understand.
Advanced Test Reactor (ATR) fuel has been identified as a resource for high-assay low-enriched uranium (HALEU) production. A survey was performed on the published literature describing ATR fuel. The geometry of the fuel is complex; different parts of the fuel compact experience differing neutron flux and burnup. The literature is sparse, and access is controlled. Therefore, fundamental studies of fuel reprocessing must use a model fuel that represents the main chemical and structural features. Advanced chlorination, or chlorination with sulfur-chlorine bearing reagents is being investigated as way to separate the fuel from metal matrix alloys. A UAl x alloy will be fabricated with x = 3, 4, and 5. The potential chlorination of individual UAl x intermetallics will be assessed in the advanced chlorination process of Al-8001 and Al-6061 as well as a representative mixture. Initial studies will track the alloying elements of the Al, which are Si, Fe, Cu, Mn, Mg, Cr, Zn, and Ti, in addition to the U itself. Further studies will include fission product simulants. Because advanced chlorination solvents include sulfur, the chemistry of sulfur with major and minor constituents will also be investigated. The experimental work accompanied by neutronic calculations will allow the assessment of the feasibility of advanced chlorination to separate aluminum from uranium. If bench-scale testing appears promising, then small-scale tests in shielded facilities with irradiated cladding, lightly irradiated fuel, and spent nuclear fuel are recommended to track the complete inventory of fissile actinides, fission product impurities, and reagent solids and liquids.
As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWd/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Composite fuel and defueled cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the post-irradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and subsequent disposition. This report documents the status of the ORNL Phase 1 DE activities related to the mechanical testing of selected sister rods in Phase 1 of the sister rod test program.
This report presents the groundwater monitoring data collected by the U.S. Department of Energy (DOE) Office of Legacy Management (LM) from the Central Nevada Test Area (CNTA), Nevada, Site, Subsurface Corrective Action Unit (CAU) 443 in Nye County, Nevada (Figure 1). The CNTA is the site of an underground nuclear test in 1968 that resulted in residual contamination near the detonation depth of 3200 feet (ft); the contamination requires long-term monitoring. Responsibility for the environmental restoration and long-term monitoring was transferred from DOE’s National Nuclear Security Administration, Nevada Field Office, to LM on October 1, 2006. The environmental restoration and site closure process were completed in 2015 in accordance with the amended 1996 Nevada Federal Facility Agreement and Consent Order (FFACO) (State of Nevada et al. 1996, as amended) and all applicable Nevada Division of Environmental Protection (NDEP) policies and regulations. The Closure Report, Central Nevada Test Area, Subsurface Corrective Action, Unit 443 (DOE 2018), also called the Closure Report, originally was completed in January 2016 and revised in October 2018; it describes LM’s plan for long-term postclosure monitoring. This includes monitoring of the radioisotopes of interest and water elevations, inspecting the site and maintaining the institutional controls (ICs), evaluating and reporting data, and documenting the site’s records and data management processes (DOE 2018).
Savannah River Mission Completion (SRMC) plans to operate Tank 27as a blend tank for future waste disposal operations. It is desirable to avoid additional worker exposure by using the planned commercial submersible mixing pump (CSMP) installations in Risers B2 and B4 to function as the blend pumps for prolonged blend tank operations. The purpose of this task is to evaluate the impacts to mixing across a range of pump installation heights from 1 to 201 inches above the tank floor. The CSMPs shall maintain adequate blending within a 24 hour maximum timeframe and an adequate nozzle discharge velocity as outlined in U-ESR-G-00030, using the specifications of the planned CSMPs listed in PO SRRA149971 and M-DS-G-00081. Specifications include: maximum pump diameter of D=22.5 in., dual nozzles placed tangentially opposed with nominal inside diameter of 2 in., total flow range (both nozzles combined) of 500 to 1950 GPM and maximum RPM of 1800. Tank 27 is expected to have a fill height maximum of 360". This analysis began by using results from the 2010 testing and applying them to the Tank 27 design to calculate a mixing time as a function of pump flow rate. These results were modified to account for the higher liquid level in Tank 27. Once the liquid level was increased to 360 inches, the results were modified to account for a higher viscosity in Tank 27 than in the testing. Once the viscosity was increased, the effect of changing pump elevation was applied to calculations of the mixing time in Tank 27. Finally, the uncertainty from the testing was included in the analysis to recommend a blend time as a function of pump flow rate and elevation. The conclusion from this study is that the particles in tank 27 will be suspended at both the 600 and 900 gpm flow rates. Only particles above 90 micron will not be suspended in significant amounts when the flow rate is 600 gpm. At 900 gpm even 100 micron particles were thoroughly suspended in the tank. From the series of simulations it has been concluded that it will not be possible to mix tank 27 at the proposed fluid flow rates and not suspend the solid particles at the bottom of the tank.
With the continued advancement of additive manufacturing (AM) techniques, interest has grown in the development and qualification of steels produced via these methods for use in the structural components of advanced nuclear reactors. Therefore, it is crucial that the properties of these materials such as the tensile strength and fracture toughness be investigated following neutron irradiation to support their use in industry. To that end, a test plan to irradiate several tensile and bend bar specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory was proposed, along with the development of a new “MINBEN” capsule design that features MBS-1 bend bar specimens that have a larger cross-sectional area than those of previous designs, which allows for higher temperature out-of-pile testing. The specimens include AM 316H stainless steel with wrought 316H and A709 stainless steels for reference, and they will be irradiated at 2 dpa and 10 dpa—corresponding to roughly 1 and 5 cycles at the HFIR midplane—at temperatures of 400°C and 600°C. The MINBEN design was found to be capable of providing specimen test plane average temperatures in the range of 220–660°C for six specimens, with a min-max spread in this temperature of ~40°C and a 95% confidence interval of ~24°C. This analysis shows that the capsule provides an effective vehicle for gathering needed high-temperature fracture toughness data.
This report describes the design, thermal modeling, and gamma irradiation testing of an optical fiber–based gamma thermometer (OFBGT), which was irradiated in the High Flux Isotope Reactor (HFIR) Gamma Irradiation Facility (GIF). OFBGTs are a promising technology for application in nuclear reactors because they can provide a distributed measurement of gamma ray heating rate, unlike thermocouple-based gamma thermometers, which are fixed in-core sensors that can be used in boiling water reactors to calibrate local power range monitors. OFBGTs measure gamma ray heating rate by measuring the temperature difference between a pair of optical fibers; one fiber is in thermal contact with a heat sink (usually the reactor coolant), and the other is in thermal contact with a thermally isolated mass. The device can be calibrated with a heating wire within the thermal mass. The OFBGT that was designed and fabricated at Oak Ridge National Laboratory can measure distributed gamma ray heating rate over an effective measurement length of 61 cm, and the outer diameter of the sensor is 12.7 mm, giving the prototypical sensor design a relatively small footprint. The sensor housing is backfilled with Ar to ensure a well-predicted thermal response that is not affected by humidity or chemical interactions during operation. For calibration, the sensor design uses a Ni–Cr wire, which can be supplied with currents from 0 to 1 A to capture the wide range of potential gamma ray heating rates expected in HFIR’s spent fuel elements. The OFBGT was thermally modeled analytically and numerically; both models account for temperature-dependent thermal conductivities of the materials and show good agreement. The thermal response of the sensor inside spent HFIR fuel elements was simulated for times up to 1 year after discharge of the fuel element. Out-of-pile open-air tests indicated that the steady-state response of the sensor matches modeled results within experimental uncertainty. Calibration tests were performed using electrical heating in the HFIR spent fuel pool, above the fuel elements, to establish a relationship between the difference in spectral shift measured by optical fibers located inside and outside the OFBGT and the applied electrical heating. Subsequently, the OFBGT was placed within the the spent fuel element from HFIR cycle 501 to measure the spatial profile of the gamma heating rates. Results showed good agreement between the theoretical and measured gamma dose rate profiles, with maximum deviations of ~10% or less.
This report provides an update on the status of the creep rupture testing on the precipitation treated (PT) Alloy 709 samples fabricated from the first, the second and the third commercial heats, in support of the American Society of Mechanical Engineers (ASME) Alloy 709 Code Case development. In Fiscal Year (FY) 23, 11 new tests were initiated and 11 tests were ruptured, some of those were initiated in FY21 or FY22. This report presents the creep data and the metallographic observations on selected rupture specimens.
DarkNESS is an effort to look for a 3.5 keV signal in the Milky Way using CCDs. The goal is to build a lab test station using an Arduino microcontroller and implement a Proportional, Integral and Derivative control scheme to stabilize the temperature for a CCD inside of a vacuum chamber and future testing. A way to monitor real time data from the temperature and pressure inside the vacuum chamber was also applied within the lab test station.
The U.S. DOE’s National Reactor Innovation Center (NRIC) hosts an open-source website and associated GitHub repository called the Virtual Test Bed (VTB) on which computational models for advanced reactors are documented and shared with the reactor community. In FY23 under the NRIC program, computational models for nuclear reactor analysis were developed and contributed to the VTB Github repository during FY23 by contributors at Argonne National Laboratory. Other models developed outside of NRIC were also ported to the VTB as part of this work, serving a broader mission to make computational reactor analysis models more widely available to the reactor community. The model development activities focused on demonstration of gas-cooled microreactor models including computational fluid dynamics simulations of flow through an industry-inspired air jacket design, and simulation of multiphysics transients for a gas-cooled microreactor assembly. Additionally, development of a molten salt reactor (led at Idaho National Laboratory) was supported through Argonne’s expertise in multigroup cross sections generation. Models for these two reactor types were targeted due to their relevancy to NRIC’s Demonstration of Microreactor Experiments (DOME) and Laboratory for Operation and Testing in the U.S. (LOTUS) physical test beds, which are slated to host microreactor and molten salt reactor experiments. The model porting activities consisted of developing detailed documentation for several physics models which originate from the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. We include only contributions from Argonne National Laboratory in this report.
With the approval of President Franklin D. Roosevelt to begin the research on a nuclear bomb in 1941 to the last test conducted by the U.S. in 1992, the fifty-year history of the nuclear weapons testing program has been an expansive topic of research. The program's growth is credited to the race to build the first atomic weapon for war. The termination of the Soviet Union and many other factors, including concerns about the adverse health effects of radioactive fallout, influenced the decline of the need for the program. The discovery of the negative health effects caused by low-level radiation and the subsequent studies influenced sitting U.S. presidents in passing policies that significantly impacted the nuclear weapons testing program.
This report presents the microstructural characterization using scanning transmission electron microscopy (STEM) of two creep-tested ESR1150-PT specimens, one short-term and one long-term. The results show that during creep testing, the microstructure of the A709 ESR1150-PT material continues to evolve as expected due to the synergistic effect of strain, temperature and time. Key features include dislocation forest and cell structures, precipitates on grain boundaries, precipitates randomly within grains, and precipitates associated with dislocations. In addition, the STEM study of one ESR1100-SA specimen that has been tested to rupture at a relatively low temperature (550°C) for a relatively long term (16226 h) is also presented. The results show that there is a high density of very fine nano precipitates form on dislocations.
The development and deployment of accident-tolerant cladding materials in light water nuclear reactors requires the collection of neutron-irradiated properties of these materials with specific consideration to the material properties orientation (i.e., tube geometry). To that end, a test plan to irradiate several cladding tube and ring specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) was proposed, along with the development of a new capsule design that features ring specimens with a preexisting gauge section. This ring specimen geometry removes the need to machine a gauge section on the irradiated specimen and thus allows for direct application of a ring-pull test post-irradiation. The test matrix includes uncoated and chromium-coated Zircaloy-4 and advanced zirconium alloy cladding specimens, pre-characterized at ORNL. Plans are to irradiate the specimens at about 4 and 10 dpa—corresponding to two and five cycles at the HFIR centerline—with a target specimen gauge section temperature of 330°C.
This report documents the deployment of non-destructive testing (NDT) technologies at the Mechanisms Engineering Test Loop (METL). METL became operational in September 2018 with the mission to provide an ecosystem for Advanced Reactor Development (ARD). METLs flagship facility’s primary purpose is conducting small to intermediate scale tests for Sodium Fast Reactors (SFR). Its resemblance to a commercial SFR’s intermediate heat transport system, prototypic operating conditions, and industrial construction practices/materials provides the overarching benefit of establishing a proving ground for devices of all technology readiness levels as well as commercial off-the-shelf equipment yet to be demonstrated on a sodium system.
Savannah River National Laboratory (SRNL) has further characterized insoluble solids that were observed in a variable depth sample from a salt dissolution campaign in Tank 9H. The insoluble solids were determined to be predominately gibbsite, a mineral form of aluminum hydroxide. From a review of salt dissolution testing and field experience, SRNL provided a realistic estimate of 8 vol% for solids of this type is formed per volume of saltcake dissolved. This estimate was doubled to 16 vol% to account for dissolution test uncertainty and differences between in-tank settling and laboratory testing. Savannah River Mission Completion (SRMC) is currently assessing the solids formed during salt dissolution as slurried sludge for hydrogen retention and release, which is driving flammability controls during salt dissolution activities. SRMC has requested SRNL perform a gas retention and release study to better understand the impact of the insoluble solids on waste tank flammability, and to provide a more accurate estimate of their ability to retain and release flammable gases.
The U.S. Department of Energy (DOE) Office of Nuclear Energy’s Advanced Modeling and Simulation (NEAMS) Program develops models of advanced reactor phenomena to demonstrate code applicability to challenging physics problems, drive code development through user assessment, and perform code verification and validation. Meanwhile, the U.S. DOE’s National Reactor Innovation Center (NRIC) hosts an open-source website and associated GitHub repository called the Virtual Test Bed (VTB) on which computational models for advanced reactors are documented and shared with the reactor community. This work documents NEAMS efforts to support industry adoption of advanced modeling tools through contribution of 10 NEAMS models to the NRIC Virtual Test Bed including models for the High Temperature Test Facility (HTTF), TRISO fuel failure in a microreactor, and multiphysics models of a molten chloride fast reactor, among others. The open sharing of these models benefits the reactor community by providing “best practice” examples using NEAMS tools for advanced reactor physics problems. In particular, the HTTF model is being used for code validation and benchmarking activities. The microreactor and molten chloride fast reactor models are representative of analysis that may be useful for current candidates of DOME and LOTUS, NRIC’s physical testbeds. This report summarizes and provides links to these new models, among others.