SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Lunar glassy objects and mineral grains surface microstructure by optical and scanning electron microscopy, comparing with tektites and terrestrial volcanic analogs
X ray probe, scanning electron microscopy and spectral reflectance analysis of lunar environment effects on Apollo 12 returned Surveyor 3 materials surface cratering
The X-ray and gamma-ray induced decomposition of ammonium perchlorate was studied by optical, transmission, and scanning electron microscopy. This material is a commonly used oxidizer in solid propellents which could be employed in deep-space probes, and where they will be subjected to a variety of radiations for as long as ten years. In some respects the radiation-induced damage closely resembles the effects produced by thermal decomposition, but in other respects the results differ markedly. Similar radiation and thermal effects include the following: (1) irregular or ill-defined circular etch pits are formed in both cases; (2) approximately the same size pits are produced; (3) the pit density is similar; (4) the c face is considerably more reactive than the m face; and (5) most importantly, many of the etch pits are aligned in crystallographic directions which are the same for thermal or radiolytic decomposition. Thus, dislocations play an important role in the radiolytic decomposition process.
Two methods of surface area estimations of sintered silver electrodes have given roughness factors of 58 and 81. One method is based on constant current oxidation, the other is based on potentiostatic oxidation. Examination of both wire and sintered silver electrodes via scanning electron microscopy at various stages of oxidation have shown that important structural features are mounds of oxide. In potentiostatic oxidations these appear to form on sites instantaneously nucleated while in constant current oxidations progressive nucleation is indicated.
Measured spectral reflectance, evidence obtained from photographs, scanning electron microscopy, and previous work on Surveyor hardware were used to develop an understanding of the observed discoloration and its meaning to future space and lunar operations. Measured reflectance data were analyzed to separate and understand the effects of lunar dust and radiation damage. It was concluded that organic contamination is not a major contributor to the discoloration. Radiation-induced discoloration on the various surfaces was found to be proportional to the degree of solar illumination. Photobleaching of the radiation damage was observed and was responsible for a gradual change in the color of the camera's surface during the evaluation.
As part of the investigation of Surveyor 3 materials, a study was conducted to determine the effect of the lunar environment on some of the painted and unpainted exterior surfaces. Examination of the camera parts and tube sections was conducted using three techniques: (1) optical and scanning electron microscopy, (2) energy dispersive X-ray probe analysis, and (3) spectral reflectance measurements.
The He-4 and Ne-20 contents in sections of the Surveyor 3 support strut samples were determined by optical and scanning electron microscopy and are compared to the results of the Apollo solar wind composition (SWC) experiments. The He-4/Ne-20 ratio in the samples from the sunlit side of the strut was approximately 300; the ratios determined in Apollo 12 lunar fines and SWC foil were below 100. The He-4/He-3 ratios were also determined, and the ratio obtained from Surveyor 3 material is higher than those found with Apollo 11 and 12 SWC experiments. The effects of spallation by cosmic rays or solar protons, stripping by cosmic ray or energetic solar alpha particles, recycling of solar wind He and radiogenic Ne, He from terrestrial atmosphere, mass discrimination near the moon, mass dependence of trapping probability, diffusion, and contamination by lunar dust are considered.
Samples of glass from the Surveyor 3 TV camera filter were examined for particle tracks by optical and scanning electron microscopy. The corrected density value is 1.7 million + or - 0.1 million tracks/sq cm, and the track density vs depth curve is determined. Comparisons with other estimated and calculated data are discussed, and lack of agreement between data sets is considered. It is felt that considerable erosion occurs, and that erosion also occurs by a flaking of small thicknesses of material, possibly caused by solar wind irradiation.
The results of a metallographic study of two coated columbium shuttle candidate materials are presented. Optical and scanning electron microscopy examinations were conducted on coating R512E and VH109.
The three-dimensional organization of spherical colonies formed by L5178Y cells grown in soft agar cultures was investigated by light and scanning electron microscopy. Visible colonies were formed after 7 days of incubation and increased in size for more than 2 weeks. At this time the colonies contained a central core of necrotic cells surrounded by an outer shell of normal-looking cells in loose contact with each other. Cross sectional radioautographs revealed that tritiated precursors were incorporated only into those cells in the ?viable cell' shell and not in the necrotic center of the colony. It is pointed out that increased knowledge of the factors leading to this type of three-dimensional organization is of particular interest, since it is similar to the conditions found in certain types of solid tumors (Thomlinson and Gray, 1955).
Sputtered MoS2 films (2000-6500 A) were deposited on highly polished metal surfaces. These films have a low coefficient of friction (0.03-0.04) at speeds of 40-80 rpm and loads of 250-1000 grams. At loads of 250 grams the wear lives are over 0.5 million cycles, but at 1000 gram loads, it decreases to 38,000 cycles. Friction experiments and tensile tests have indicated that sputtered films have a strong adherence to metal surfaces. Electron transmission, diffraction and scanning electron microscopy show that these films have an extremely small particle size, less than 30 A in diameter, and are very dense and free from observable pinholes. The high kinetic energy of these sputtered species, the submicroscopic particle size and the sputter-etched substrate surface is responsible for strong adhesion and cohesion of the sputtered film.
Sputtered MoS2 films (2000-6500 A) were deposited on highly polished metal surfaces. These films have a low coefficient of friction (0.03-0.04) at speeds of 40-80 rpm and loads of 250-1000 grams. At loads of 250 grams, the wear lives are over 0.5 million cycles, but at 1000 gram loads, it decreases to 38,000 cycles. Friction experiments and tensile tests have indicated that sputtered films have a strong adherence to metal surfaces. Electron transmission, diffraction, and scanning electron microscopy show that these films have an extremely small particle size less than 30 A in diameter and are very dense and free from observable pinholes.
A simple device for producing cumulative shock loading in solids is described. The device uses a ballistic-impact-driven projectile to introduce high-stress waves into a solid. The impact time and load amplitude can be varied to produce fracture in one or several impacts in PMMA rods. The wavefront approached a square wave shape. Materials other than PMMA were loaded to failure to demonstrate the versatility of the device. Fracture morphologies observed with optical and scanning-electron microscopy are described.
Discussion of the microimpact-crater morphology observed by scanning electron microscopy on a glass bead (nearly 580 microns in maximum diameter) recovered from zone A of the Luna 16 sample. The microcrater has a diameter of approximately 200 microns and a centrally located melted region or pit that is slightly elevated above the surrounding area. Around the pit is a radial fracture zone half of which has spalled off. The spall zone is more than half again as large as the radial fracture zone.
Study of volcanic ash samples collected from a variety of recent eruptions using petrography, chemical analyses, and scanning electron microscopy to characterize each type and to relate ash morphology to magma composition and the type of eruption. The ashes are placed in the broad genetic categories of magmatic and phreatomagmatic. The morphology of ash particles from magmatic eruptions of high viscosity magma is governed primarily by vesicle density and shape. Ash particles from eruptions of low viscosity magmas are mostly droplets. The morphology of ash particles from phreatomagmatic eruptions is controlled by stresses within the chilled magma which result in fragmentation of the glass to form small blocky or pyramidal glass ash particles.
Sliding friction experiments were conducted in air with polycrystalline copper and ruby riders sliding against a copper bicrystal. Friction coefficient was measured across the bicrystal surface, and the initiation of adhesive wear was examined with scanning electron microscopy. Results indicate a marked increase in friction coefficient as the copper rider crossed the grain boundary from the (111) plane to the (210) plane of the bicrystal. Adhesion, friction, and initiation of adhesive wear was notably different in the adjacent grains of differing orientation. A slip-band adhesion-generated fracture mechanism for wear particle formation is proposed.
The high temperature deformation and fracture behavior of T-111 and ASTAR-811C were studied over the temperature range 982 to 2205 C (1800 to 4000 F). As-cast and wrought-recrystallized material as well as GTA welds in sheet and plate were evaluated using conventional tensile and creep tests. Post test examinations were performed using optical metallography, scanning electron microscopy and transmission electron microscopy. A high temperature region of reduced ductility, in terms of tensile elongation, was identified for both alloys. The reduction in tensile elongation became more severe with increase in grain size, being near catastrophic for the as-cast specimens. Optical and electron metallography indicated that even for failures at very low total strain, considerable deformation of a very localized nature had occurred prior to fracture.
Diffusion-bonded joints between gold-plated Kovar leads and indium-plated copper circuit pads offer some advantages for electronic circuit packaging. Test results show that consistent high strength bonds stronger than the copper circuit foil are achieved by parallel-gap bonding at relatively low power settings. The bonds are basically formed by the alloying of the gold, indium and copper at the bond interface. Other low melting metals such as tin can also be used; however, tin does not offer the ease of bonding that results in consistent separation of the copper foil during pull testing. The investigation was conducted in three parts consisting of: (1) an evaluation of the physical strength of resulting bonds at ambient and elevated temperature, (2) a metallurgical analysis of bonds using scanning electron microscopy and nondispersive X-ray analysis, and (3) evaluation and development of various schemes for multiple lead flatpack bonding.