Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Recombinant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Arsenic activation and compensation in single crystal CdTe bilayers

In state-of-the art polycrystalline CdTe photovoltaics, group-V dopant activation is about 2%. Low activation can create electronic defects and lead to recombination and band tail losses. To develop methods to overcome this limitation, dopant activation was systematically investigated using molecular beam epitaxy (MBE) grown single crystal bilayers of As-doped CdTe on undoped CdTe. Results suggest multiple paths for improved As-activation in polycrystalline CdTe-based devices. It was found that the carrier concentration in this MBE material saturated at ∼3 × 1016 cm−3, with high levels (>50%) of As-activation possible. High activation could be achieved with a post-growth activation temperature of ∼450 °C, when the initial doping level was below the saturation level. However, at typical polycrystalline As incorporation levels (>5 × 1016 cm−3), the excess As is inactive or compensating, requiring elevated temperatures (500–600 °C) to achieve high activation. Oxygen in the annealing ambient was detrimental, while the effect of CdCl2 in the ambient is more case-dependent. A 575 °C activation anneal was combined with a 450 °C CdCl2 treatment to better understand the implications for polycrystalline CdTe. Interestingly, on highly doped samples, processes ending with a high temperature step displayed high activation, while those ending at 450 °C significantly reduced the carrier concentration (with or without CdCl2 in the ambient). Low activation can be restored with another high temperature anneal, allowing reproducible toggling between high and low activation based on the final temperature. Photoluminescence revealed the presence of donor–acceptor pairs in the low activation state that appear to be associated with a compensating defect.

14 SOLAR ENERGY↗
DOE OSTI2025

Thermoradiative energy conversion in infrared interband cascade InAs/GaSb/AlInSb/GaSb type-II superlattice diodes

Thermoradiative energy conversion presents a means for the direct conversion of thermal energy through radiative transfer to a cold scene. However, much of the study of thermoradiative principles has been based on theory and simulations, with only sparse reports on the experimental demonstration of the concept. This work studies thermoradiative energy conversion in InAs/GaSb/AlInSb/GaSb type-II superlattice cascade devices. The devices exhibit a cutoff wavelength of 3.2 μm at 300 K, corresponding to a bandgap of 0.39 eV. Testing under a temperature-controlled chamber and scene demonstrates a maximum power density of 2.9 mW/m2 at a cell temperature of 121 °C. It is consistent with expected values for device operation limited by Shockley–Read–Hall non-radiative recombination. This result is a significant step in providing an experimental demonstration of thermoradiative energy conversion and a means to characterize cell performance, providing a foundation for further development to achieve practical values for power generation.

Islam, Md Toriqul (ORCID:0000000249871320)↗
DOE OSTI2025

Efficiency cliff in scaling InGaN light-emitting diodes down to submicron

The top-down submicron fabrication of blue-emitting light-emitting diodes on Qromis Substrate Technology substrates is reported. Light-emitting diodes with mesa sizes as small as 250 × 250 nm 2 show ideal forward voltage and low leakage current density. It is observed that sidewall treatment and passivation methods used in micro-light-emitting diodes (2–20 μ m) do not lead to the same level of sidewall recombination suppression for submicron ones (< 1 μ m), as evidenced by a ∼70% decrease in peak external quantum efficiencies when mesa sizes are scaled from 2 μ m down to 250 nm. This is attributed to the lateral carrier diffusion being comparable to the mesa size, regardless of the sidewall passivation and recovery. The results call for rethinking the impact of sidewalls in emerging top-down fabricated (sub)micrometer-light-emitting diodes.

42 ENGINEERING↗
DOE OSTI2025

Impact of quantum well thickness on efficiency loss in InGaN/GaN LEDs: Challenges for thin-well designs

We investigate the impact of quantum well (QW) thickness on efficiency loss in c-plane InGaN/GaN LEDs using a small-signal electroluminescence technique. Multiple mechanisms related to efficiency loss are independently examined, including injection efficiency, carrier density vs current density relationship, phase space filling, quantum-confined Stark effect, and Coulomb enhancement. An optimal QW thickness of around 2.7 nm in these InGaN/GaN LEDs was determined for QWs having constant In composition. Despite improved control of deep-level defects and lower carrier density at a given current density, LEDs with thin QWs still suffer from an imbalance in enhancement effects on the radiative and intrinsic Auger–Meitner recombination coefficients. The imbalance in enhancement effects results in a decline in internal quantum efficiency and radiative efficiency with decreasing QW thickness at low current density in LEDs with QW thicknesses below 2.7 nm. Here, we also investigate how LED modulation bandwidth varies with QW thickness, identifying the key trends and their implications for device performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Characterization of dangling bond defects at the crystalline Si/SiO x interface in a polycrystalline Si passivating contact solar cell at room temperature with electrically detected magnetic resonance spectroscopy

Monocrystalline silicon solar cells can achieve photoconversion efficiencies exceeding 26%; however, performance-limiting defects that trap carriers continue to be a challenge. In this work, we have characterized Si solar cells with tunneling SiO x /polycrystalline-Si (poly-Si) passivating contacts (TOPCon) on As-doped Czochralski Si wafers with electrically detected magnetic resonance (EDMR) spectroscopy. We fabricated 2 × 20 mm 2 TOPCon-like mini solar cells with edge passivation alongside larger 4 cm 2 sister cells and obtained similar device characteristics. We performed EDMR spectroscopy at 300 K on two minicells with different degrees of surface passivation based on the recombination parameter, J o , values of 40 and 310 fA/cm2. We optimized the resolution and the signal-to-noise ratio of the EDMR response of the minicells by varying the forward bias voltage and the magnetic field modulation amplitude. We detect two distinct signals with EDMR spectroscopy, an axial-like signal at g = 2.009, 2.0087, and 2.0015, and an isotropic signal at g = 2.0024, which we attribute to Si dangling bonds (P b0 and P b centers) and boron–oxygen related defects, respectively, at or near the c-Si/SiO x interface. The EDMR signals were lower for the cell with a lower value of J o , while the ratio of the two defect populations was very similar. The EDMR signal increases with forward bias but drops to zero at bias voltages >0.5 V, consistent with interface defects within or near the boron-doped emitter depletion region. Our study demonstrates a method to fabricate minicells that can be characterized with EDMR spectroscopy to detect industrially relevant defects in TOPCon cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Longitudinal position dependence of dark line defect growth rate in high-power diode lasers at 790 nm

Using a nondestructive, in situ near-infrared defect imaging technique, we obtained time-resolved images of dark line defect (DLD) growth in the cavities of several high-power 790-nm diode lasers and calculated individual DLD growth rates. A clear longitudinal spatial dependence in the DLD growth rate was observed, in which the DLD growth rate was faster near the anti-reflective (AR) facet. Longitudinal spatial hole burning simulation results indicate that the total photon density increases toward the AR facet, while the carrier density decreases toward the AR facet. Here, these results suggest that photon absorption plays a key role in enhancing DLD growth beyond the contribution of the traditional carrier capture mechanism. Asymmetric DLD growth that was preferentially directed toward the high-reflectivity facet was also observed, providing further support for the role of photon absorption in the growth process. To account for these findings, we propose a photon-accelerated mechanism for the enhancement of DLD growth in which the slower carrier capture process in the traditional recombination-enhanced dislocation glide mechanism is replaced by a faster photon absorption process.

Engineering - Electronic and electrical engineerin↗
DOE OSTI2025

Experimental study of high-energy single-pulse nanosecond discharges in pin-to-pin configuration

Single-pulse pin-to-pin nanosecond pulsed discharges in ambient air (gap distances of 3–7 mm) were investigated at high pulse energies (∼20–30 mJ deposited energy per 11 ns full width at half maximum pulse). A Michelson interferometry setup (532 nm continuous-wave laser) was employed to record time-resolved interferograms of the discharge, enabling spatially resolved calculation of the electron number density. An intensified charge-coupled device camera was used to capture the spatiotemporal evolution of the discharge (streamer formation and spark channel development), and Coherent Anti-Stokes Raman Spectroscopy (CARS) was used to measure post-discharge N 2 vibrational temperatures. Discharge current and voltage were monitored with a back-current shunt. The discharge was initiated with simultaneous cathode-directed and anode-directed streamers that bridge the gap within ∼1 ns and form a luminous, filamentary plasma channel immediately after breakdown. Laser interferometry measurements showed peak electron number densities of the order of 10 1 7–10 18 cm −3 , occurring about 15–20 ns after pulse arrival at the discharge gap. Shorter gap discharges yielded higher peak electron densities, consistent with the higher energy density in the smaller gaps. Spatially, the electron density was highest near the electrodes and decreased toward the midgap region, with 5 and 7 mm gaps exhibiting a pronounced drop in the central channel. CARS indicated initial vibrational temperatures of approximately 4000–6000 K in the spark core of ∼50 ns after the discharge onset, decaying on a ∼500 ns timescale as the plasma cooled and recombined.

Coherent anti-Stokes Raman spectroscopy↗
DOE OSTI2026

Analysis of native oxides grown on single-crystal CdTe and MgCdTe

Over the course of CdTe photovoltaics development, many refinements to the device stack have been made. One area of current interest is the back contact interface, where surface passivation is critical to prevent recombination at the interface. One candidate material for achieving strong passivation is TeO 2 . Using scanning transmission electron microscopy, we investigate native oxide formations on CdTe and Mg x Cd 1−x Te substrates to better understand the oxides' chemical composition and the interface they form with the material they are grown on. We find that substoichiometric TeO x forms as a native oxide on CdTe, and on Mg x Cd 1−x Te, we found a MgO native oxide. Some TeO x appeared atop the MgO layer, though it was not consistently present. As a result, the native oxides had preferential interface terminations, with Cd terminations at the CdTe/TeO x interface and Te terminations at the Mg x Cd 1−x Te/MgO interface.

14 SOLAR ENERGY↗
DOE OSTI2026

Correlation of coercivity, microstructure, and surface defects in HDDR-processed Nd-Fe-B powders for bonded magnet applications

Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) is an effective method for producing high coercivity, anisotropic powder from either fresh Nd-Fe-B alloy or recycled Nd-Fe-B magnets for use in bonded magnets. We investigated the impact of surface defects on the coercivity of HDDR-processed Nd-Fe-B using scanning electron microscopy (SEM), magnetic measurements, and micromagnetic simulations. We observed that coercivity decreases as particle size reduces, with SEM revealing surface defects and the detachment of Nd 2 Fe 14 B grains and Nd-rich phases from the particle surface. Micromagnetic simulations indicate that demagnetization initiates at the particle surface, where these defects are most concentrated, leading to reduced coercivity. The reduction in squareness of demagnetization curve, knee point field and coercivity for smaller HDDR particles is attributed to an increased specific surface area, which exhibits reduced nucleation field and weak domain wall pinning field during magnetization reversal. By addressing the role of surface defects in coercivity degradation, this study provides insights for improving both new powder production and recycling strategies, ultimately leading to enhanced performance of bonded magnets and contributing to more sustainable practices in the rare earth supply chain. One potential strategy to enhance the performance of HDDR Nd-Fe-B materials involves reducing the fraction of fine particles ($<$35 µm) and promoting the formation of grain boundary phases on particle surfaces.

Liu, Xubo B. [Ames Laboratory (AMES), Ames, IA (Un↗
DOE OSTI2020

Longitudinal spatial hole burning in high-power semiconductor lasers: numerical analysis

Longitudinal spatial hole burning (LSHB) in high-power semiconductor lasers is analysed by numerically solving one-dimensional (1D) rate equations. Calculations are performed for GaAs-based lasers operating at a wavelength of 1.06 μm. It is shown that the LSHB-induced decrease in output power can be accounted for by two mechanisms: build-up of spontaneous recombination and decrease in slope efficiency, equivalent to a rise in internal optical loss. We analyse the influence of different laser chip parameters on the magnitude of the LSHB effect. In particular, it is shown that to suppress LSHB it is preferable to increase the optical confinement factor Γ. We examine the relationship between LSHB and other mechanisms capable of reducing the output power. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Spatially separating redox centers on 2D carbon nitride with cobalt single atom for photocatalytic H 2 O 2 production

Redox cocatalysts play crucial roles in photosynthetic reactions, yet simultaneous loading of oxidative and reductive cocatalysts often leads to enhanced charge recombination that is detrimental to photosynthesis. This study introduces an approach to simultaneously load two redox cocatalysts, atomically dispersed cobalt for improving oxidation activity and anthraquinone for improving reduction selectivity, onto graphitic carbon nitride (C 3 N 4 ) nanosheets for photocatalytic H 2 O 2 production. Spatial separation of oxidative and reductive cocatalysts was achieved on a two-dimensional (2D) photocatalyst, by coordinating cobalt single atom above the void center of C 3 N 4 and anchoring anthraquinone at the edges of C 3 N 4 nanosheets. Such spatial separation, experimentally confirmed and computationally simulated, was found to be critical for enhancing surface charge separation and achieving efficient H 2 O 2 production. This center/edge strategy for spatial separation of cocatalysts may be applied on other 2D photocatalysts that are increasingly studied in photosynthetic reactions.

2D photocatalyst↗
DOE OSTI2020

Swine acute diarrhea syndrome coronavirus replication in primary human cells reveals potential susceptibility to infection

Zoonotic coronaviruses represent an ongoing threat, yet the myriads of circulating animal viruses complicate the identification of higher-risk isolates that threaten human health. Swine acute diarrhea syndrome coronavirus (SADS-CoV) is a newly discovered, highly pathogenic virus that likely evolved from closely related HKU2 bat coronaviruses, circulating in Rhinolophus spp. bats in China and elsewhere. As coronaviruses cause severe economic losses in the pork industry and swine are key intermediate hosts of human disease outbreaks, we synthetically resurrected a recombinant virus (rSADS-CoV) as well as a derivative encoding tomato red fluorescent protein (tRFP) in place of ORF3. rSADS-CoV replicated efficiently in a variety of continuous animal and primate cell lines, including human liver and rectal carcinoma cell lines. Of concern, rSADS-CoV also replicated efficiently in several different primary human lung cell types, as well as primary human intestinal cells. rSADS-CoV did not use human coronavirus ACE-2, DPP4, or CD13 receptors for docking and entry. Contemporary human donor sera neutralized the group I human coronavirus NL63, but not rSADS-CoV, suggesting limited human group I coronavirus cross protective herd immunity. Importantly, remdesivir, a broad-spectrum nucleoside analog that is effective against other group 1 and 2 coronaviruses, efficiently blocked rSADS-CoV replication in vitro. rSADS-CoV demonstrated little, if any, replicative capacity in either immune-competent or immunodeficient mice, indicating a critical need for improved animal models. Efficient growth in primary human lung and intestinal cells implicate SADS-CoV as a potential higher-risk emerging coronavirus pathogen that could negatively impact the global economy and human health.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

High-throughput functional variant screens via in vivo production of single-stranded DNA

Significance We report a methodology for the pooled construction of mutants bearing precise genomic sequence variations and multiplex phenotypic characterization of these mutants using next-generation sequencing (NGS). Unlike existing techniques depending on CRISPR-Cas–directed genomic breaks for genome editing, this strategy instead uses single-stranded DNA produced by a retron element for recombineering. This enables libraries of millions of elements to be constructed and offers relaxed design constraints which permit natural DNA or random variation to be used as inputs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Structure and dynamics of SARS-CoV-2 proofreading exoribonuclease ExoN

High-fidelity replication of the large RNA genome of coronaviruses (CoVs) is mediated by a 3'-to-5' exoribonuclease (ExoN) in nonstructural protein 14 (nsp14), which excises nucleotides including antiviral drugs misincorporated by the low-fidelity viral RNA-dependent RNA polymerase (RdRp) and has also been implicated in viral RNA recombination and resistance to innate immunity. Here, we determined a 1.6-Å resolution crystal structure of severe acute respiratory syndrome CoV 2 (SARS-CoV-2) ExoN in complex with its essential cofactor, nsp10. The structure shows a highly basic and concave surface flanking the active site, comprising several Lys residues of nsp14 and the N-terminal amino group of nsp10. Modeling suggests that this basic patch binds to the template strand of double-stranded RNA substrates to position the 3' end of the nascent strand in the ExoN active site, which is corroborated by mutational and computational analyses. We also show that the ExoN activity can rescue a stalled RNA primer poisoned with sofosbuvir and allow RdRp to continue its extension in the presence of the chain-terminating drug, biochemically recapitulating proofreading in SARS-CoV-2 replication. Molecular dynamics simulations further show remarkable flexibility of multidomain nsp14 and suggest that nsp10 stabilizes ExoN for substrate RNA binding to support its exonuclease activity. Our high-resolution structure of the SARS-CoV-2 ExoN–nsp10 complex serves as a platform for future development of anticoronaviral drugs or strategies to attenuate the viral virulence.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Accelerating strain phenotyping with desorption electrospray ionization-imaging mass spectrometry and untargeted analysis of intact microbial colonies

Significance Synthetic biology has entered an era in which reading and writing DNA sequences are no longer rate-limiting steps in microbial strain engineering. Indeed, analytical methods measuring the resulting metabolic outcomes of specific gene edits have lagged behind the ability to generate new recombinant strains. Herein, we report a mass spectrometry strategy to accelerate these analytical workflows by directly analyzing metabolites and molecules produced from engineered microorganisms in a multiplexed process. Using untargeted acquisitions and unsupervised analytics, we assess the molecular features that change across discrete strains including primary target species, secondary products, and species outside the engineered fatty acid biosynthesis pathway.

09 BIOMASS FUELS↗
DOE OSTI2022

Cryo-EM structure of RNA-induced tau fibrils reveals a small C-terminal core that may nucleate fibril formation

In neurodegenerative diseases including Alzheimer’s and amyotrophic lateral sclerosis, proteins that bind RNA are found in aggregated forms in autopsied brains. Evidence suggests that RNA aids nucleation of these pathological aggregates; however, the mechanism has not been investigated at the level of atomic structure. Here, we present the 3.4-Å resolution structure of fibrils of full-length recombinant tau protein in the presence of RNA, determined by electron cryomicroscopy (cryo-EM). The structure reveals the familiar in-register cross-β amyloid scaffold but with a small fibril core spanning residues Glu391 to Ala426, a region disordered in the fuzzy coat in all previously studied tau polymorphs. RNA is bound on the fibril surface to the positively charged residues Arg406 and His407 and runs parallel to the fibril axis. The fibrils dissolve when RNase is added, showing that RNA is necessary for fibril integrity. While this structure cannot exist simultaneously with the tau fibril structures extracted from patients’ brains, it could conceivably account for the nucleating effects of RNA cofactors followed by remodeling as fibrils mature.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

A Gauss’s law analysis of redox active adsorbates on semiconductor electrodes: The charging and faradaic currents are not independent

A detailed framework for modeling and interpreting the data in totality from a cyclic voltammetric measurement of adsorbed redox monolayers on semiconductor electrodes has been developed. A three-layer model consisting of the semiconductor space-charge layer, a surface layer, and an electrolyte layer is presented that articulates the interplay between electrostatic, thermodynamic, and kinetic factors in the electrochemistry of a redox adsorbate on a semiconductor. Expressions are derived that describe the charging and faradaic current densities individually, and an algorithm is demonstrated that allows for the calculation of the total current density in a cyclic voltammetry measurement as a function of changes in the physical properties of the system (e.g., surface recombination, dielectric property of the surface layer, and electrolyte concentration). The most profound point from this analysis is that the faradaic and charging current densities can be coupled. That is, the common assumption that these contributions to the total current are always independent is not accurate. Their interrelation can influence the interpretation of the charge-transfer kinetics under certain experimental conditions. More generally, this work not only fills a long-standing knowledge gap in electrochemistry but also aids practitioners advancing energy conversion/storage strategies based on redox adsorbates on semiconductor electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Decorating chromatin for enhanced genome editing using CRISPR-Cas9

CRISPR-associated (Cas) enzymes have revolutionized biology by enabling RNA-guided genome editing. Homology-directed repair (HDR) in the presence of donor templates is currently the most versatile method to introduce precise edits following CRISPR-Cas-induced double-stranded DNA cuts, but HDR efficiency is generally low relative to end-joining pathways that lead to insertions and deletions (indels). We tested the hypothesis that HDR could be increased using a Cas9 construct fused to PRDM9, a chromatin remodeling factor that deposits histone methylations H3K36me3 and H3K4me3 to mediate homologous recombination in human cells. Our results show that the fusion protein contacts chromatin specifically at the Cas9 cut site in the genome to increase the observed HDR efficiency by threefold and HDR:indel ratio by fivefold compared with that induced by unmodified Cas9. HDR enhancement occurred in multiple cell lines with no increase in off-target genome editing. These findings underscore the importance of chromatin features for the balance between DNA repair mechanisms during CRISPR-Cas genome editing and provide a strategy to increase HDR efficiency.

59 BASIC BIOLOGICAL SCIENCES↗