Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Viscoelastic Characterization of Polymers for Deployable Composite Booms

Deployable space structures have been built from thin-walled fiber-reinforced polymer composite materials due to their high specific strength, high specific stiffness, and bistability. However, the inherent viscoelastic behavior of the resin matrix can cause dimensional instability when parts are stored under strain. The extended time of stowage between assembly and deployment in space can result in performance degradation and in the worst case, mission failure. In this study, the viscoelastic properties of candidate commercial polymers for deployable boom structures of solar sails were evaluated. Stress relaxation master curves of the candidate polymers were used to predict the relaxation that would occur in 1 year at room temperature under relatively low strains of ~0.1%. A bismaleimide (BMI) showed less stress relaxation (about 20%) than the baseline Novolac epoxy (about 50%). Carbon fiber composites fabricated with the BMI resin showed a 44% improvement in relaxation compared to the baseline epoxy composite. Other difunctional and tetrafunctional epoxies, thermoplastic, and thermosetting polyimides were also evaluated.

Kang, Jin Ho↗
NASA NTRS2020

Popcorning Failures in Polymer and MnO2 Tantalum Capacitors

Popcorning is a well-known effect in plastic encapsulated microcircuits (PEM) and it occurs in chip tantalum capacitors. The sensitivity of components to the presence of moisture during soldering is characterized by the moisture sensitivity level (MSL); however, contrary to PEMs, there is no standard procedure for establishing MSL for tantalum capacitors.The effect of absorbed moisture on soldering related degradation and failures in tantalum capacitors have not been studied properly yet, and there is no sufficient information regarding the difference in the sensitivity to soldering between polymer and MnO2 capacitors. In this work, 16 types of polymer and 9 types of MnO2 tantalum capacitors with different moisture content have been tested before and after reflow soldering. The level of moisture release during soldering has been estimated and thermo-mechanical analysis used to assess deformation of capacitorsduring soldering simulations. Results show that moisture uptake in similar parts is approximately two times greater in polymer than in MnO2 capacitors. Cracking of the case and degradation of parameters can occur in both types of parts, but MnO2 capacitors are much more likely to fail catastrophically with a short circuit and possible ignition during the first power-on cycle. This type of failure in MnO2 capacitors is lot-related, can occur even at derated voltages and relatively low levels of moisture sorption that corresponds to room conditions. Baking before soldering is an effective measure to prevent failures even in lots susceptible to popcorning damage.

Capacitor↗
NASA NTRS2021

Effect of Soldering on Polymer and MnO2 Tantalum Capacitors

Soldering might have a strong effect on performance and reliability of most surface mount technology components, including tantalum capacitors. High quality tantalum capacitors are likely the only type of components where soldering simulation is the first step during screening. Nevertheless, post-soldering failures of tantalum capacitors happen and require additional analysis. Popcorning is a well-known effect in plastic encapsulated microcircuits (PEM) and it occurs also in chip tantalum capacitors. The sensitivity of parts to the presence of moisture during soldering is characterized by the moisture sensitivity level (MSL); however, contrary to PEMs, there is no standard procedure for establishing MSL for tantalum capacitors. The effect of absorbed moisture on soldering related degradation and failures in tantalum capacitors have not been studied properly yet, and there is no sufficient information regarding the difference in the sensitivity to soldering between polymer and MnO2 tantalum capacitors. In this work, 16 types of polymer and 9 types of MnO2 cathodes tantalum capacitors with different moisture content have been tested before and after reflow soldering. The level of moisture release after soldering has been estimated and thermo-mechanical analysis used to assess deformation of capacitors during soldering simulations. Results show that moisture uptake in similar parts is approximately two times greater in polymer than in MnO2 capacitors. Cracking of the case and degradation of parameters can occur in both types of parts, but MnO2 capacitors are much more likely to fail catastrophically with a short circuit and possible ignition during the first power-on cycle. This type of failure in MnO2 capacitors is lot-related, can occur even at derated voltages and relatively low levels of moisture sorption corresponding to room conditions. Baking before soldering is an effective measure to prevent failures even in lots susceptible to popcorning damage. Recommendations for baking and testing to establish MSL are suggested.

Alexander Teverovsky↗
NASA NTRS2021

Effect of High Temperature Storage on AC Characteristics of Polymer Tantalum Capacitors

Replacement of MnO2 with conductive polymers as cathode materials in chip tantalum capacitors allows for a substantial reduction of the equivalent series resistance (ESR), improvement of frequency characteristics, and elimination of the possibility of ignition during failures. One of the drawbacks of chip polymer tantalum capacitors (CPTCs) is a relatively poor long-term stability at high temperatures. In this work, variations of capacitance, dissipation factor, and ESR in different types of capacitors including automotive grade parts from three manufacturers have been monitored during storage at temperatures from 100 ºC to 175 ºC for up to 18,000 hours. Results show that ESR is the most and capacitance the least sensitive to degradation parameter. Times to parametric failures have been simulated using a Weibull-Arrhenius model that allowed for assessments of activation energies of the degradation and prediction of times to failure at the use temperature. Degradation of CPTCs was explained by thermo-oxidative processes in conductive polymers that result in exponential increasing of the resistivity with time of ageing. This process starts after a certain incubation period that depends on packaging materials and design and corresponds to the time that is necessary to form delamination between the encapsulating molding compound and lead frame. The effectiveness of the existing qualification procedures to assure stable operation of CPTCs is discussed.

Alexander A Teverovsky↗
NASA NTRSDate not supplied

Effect of High Temperature Storage on AC Characteristics of Polymer Tantalum Capacitors

Replacement of MnO2 with conductive polymers as cathode materials in chip tantalum capacitors allows for a substantial reduction of the equivalent series resistance (ESR), improvement of frequency characteristics, and elimination of the possibility of ignition during failures. One of the drawbacks of chip polymer tantalum capacitors (CPTCs) is a relatively poor long-term stability at high temperatures. In this work, variations of capacitance, dissipation factor, and ESR in different types of capacitors including automotive grade parts from three manufacturers have been monitored during storage at temperatures from 100 ºC to 175 ºC for up to 18,000 hours. Results show that ESR is the most and capacitance the least sensitive to degradation parameter. Times to parametric failures have been simulated using a Weibull-Arrhenius model that allowed for assessments of activation energies of the degradation and prediction of times to failure at the use temperature. Degradation of CPTCs was explained by thermo-oxidative processes in conductive polymers that result in exponential increasing of the resistivity with time of ageing. This process starts after a certain incubation period that depends on packaging materials and design and corresponds to the time that is necessary to form delamination between the encapsulating molding compound and lead frame. The effectiveness of the existing qualification procedures to assure stable operation of CPTCs is discussed.

Aging↗
NASA NTRSDate not supplied

Effect of High Temperature Storage on AC Characteristics of Polymer Tantalum Capacitors

Replacement of MnO2 with conductive polymers as cathode materials in chip tantalum capacitors allows for a substantial reduction of the equivalent series resistance (ESR), improvement of frequency characteristics, and elimination of the possibility of ignition during failures. One of the drawbacks of chip polymer tantalum capacitors (CPTCs) is a relatively poor long-term stability at high temperatures. In this work, variations of capacitance, dissipation factor, and ESR in different types of capacitors including automotive grade parts from three manufacturers have been monitored during storage at temperatures from 100 ºC to 175 ºC for up to 18,000 hours. Results show that ESR is the most and capacitance the least sensitive to degradation parameter. Times to parametric failures have been simulated using a Weibull-Arrhenius model that allowed for assessments of activation energies of the degradation and prediction of times to failure at the use temperature. Degradation of CPTCs was explained by thermo-oxidative processes in conductive polymers that result in exponential increasing of the resistivity with time of ageing. This process starts after a certain incubation period that depends on packaging materials and design and corresponds to the time that is necessary to form delamination between the encapsulating molding compound and lead frame. The effectiveness of the existing qualification procedures to assure stable operation of CPTCs is discussed.

Aging↗
NASA NTRS2021

Acceleration Factors for Reliability Assessment of Polymer Tantalum Capacitors

Using polymer tantalum capacitors in Hi-Rel systems requires an assessment of the reliability characteristics of the parts. For this assessment, tantalum capacitors are typically subjected to reliability testing at temperatures and voltages exceeding their specified values, and the failure rate (FR) — or the probability of failure during use conditions — is calculated based on voltage and temperature acceleration factors. In this work, various types and lots of polymer tantalum capacitors have been tested at highly accelerated life test (HALT) conditions and the acceleration factors have been determined using different techniques. It has been shown that the behavior of capacitors under HALT conditions can be described based on the time-dependent dielectric breakdown (TDDB) model, which explains the presence of infant mortality (IM) and wear-out failures using the same failure mechanisms and allows for an assessment of the acceleration factors. The difference in acceleration factors obtained using exponential and power models is discussed. Analysis shows that with proper derating, screening, and qualification testing, the reliability of frameless Hi-Rel COTS polymer tantalum capacitors is adequate for space missions.

Alex Eidelman↗
NASA NTRS2021

Acceleration Factors for Reliability Assessment of Polymer Tantalum Capacitors

Using polymer tantalum capacitors in Hi-Rel systems requires an assessment of the reliability characteristics of the parts. For this assessment, tantalum capacitors are typically subjected to reliability testing at temperatures and voltages exceeding their specified values, and the failure rate (FR) — or the probability of failure during use conditions — is calculated based on voltage and temperature acceleration factors. In this work, various types and lots of polymer tantalum capacitors have been tested at highly accelerated life test (HALT) conditions and the acceleration factors have been determined using different techniques. It has been shown that the behavior of capacitors under HALT conditions can be described based on the time-dependent dielectric breakdown (TDDB) model, which explains the presence of infant mortality (IM) and wear-out failures using the same failure mechanisms and allows for an assessment of the acceleration factors. The difference in acceleration factors obtained using exponential and power models is discussed. Analysis shows that with proper derating, screening, and qualification testing, the reliability of frameless Hi-Rel COTS polymer tantalum capacitors is adequate for space missions.

Alex Eidelman↗
NASA NTRS2021

Insitu Lunar Launch & Landing Pad Construction w/ Regolith and Thermoset Polymers

This CIF project is an extension of materials developed under a previous NASA Innovative Advanced Concepts (NIAC) project titled “Regolith Derived Heat Shield for Planetary Body Entry and Descent Systems with In-Situ Fabrication” by M. Hogue et al. (2012). Launch and landing pads are necessary to mitigate risks to lander/ascent vehicles, surface assets, and orbital assets from rocket plume ejected regolith. At this time, all launching and landing on the lunar surface will be on unprepared surface sites. Though this has been a successful approach for Apollo and other uncrewed missions, significant risks exist for the Artemis Program due to the increased thrust of the vehicles, presence of co-located assets, and potential surface level requirements for tall vehicles. This project developed a thermoset polymer–regolith composite material for use as a launch and landing pad. Test articles were prepared at 20% and 11% polymer mass percent (wt%) and tested under hot fire conditions that simulated large vehicle lunar launch/landing conditions. A minimum polymer wt% of 9% was achieved and both samples successfully mitigated regolith ejecta from plume effects. A concept for emplacing launch/landing pads was successfully tested in laboratory environments using a screw and barrel approach to mixing, conveying and depositing materials. It is recommended that materials and systems be developed to TRL 6 for a small-scale lunar demonstration of emplacement of a launch/landing pad via a Commercial Lunar Payload Services (CLPS) mission to support the Artemis Program.

Nathan Gelino↗
NASA NTRSDate not supplied

Forcespun Polymers as Precursors to Boron Nitride Fibers

The need for multifunctional materials in aerospace technologies is currently driving the development of new novel composite materials. Specifically, insulation materials with high thermal conductivity, high electrical resistivity, and are chemically inert are needed for high voltage power applications. Boron nitride (BN) nanomaterials fit these criteria and can be incorporated into composites for further material design. The synthesis of boron nitride through a polymer derived ceramic route allows for the morphology of the resulting BN to be tailored. This is especially beneficial since the polymers can be shaped or spun into fibers prior to the ceramic conversion. This project utilizes the Forcespinning technique to produce boron-containing polymer fibers that are converted to boron nitride through a heat treatment. The chemical compositions and fiber morphologies were studied and reported here.

Boron nitride, Fibers, Forcespinning↗
NASA NTRSDate not supplied

Overview of Results from the MISSE 9-15 Polymers and Composites Experiment 1-4 (PCE 1-4)

Spacecraft in low Earth orbit (LEO) and other planetary orbits are subjected to harsh environmental conditions that can result in erosion, embrittlement and optical property degradation of susceptible materials threatening spacecraft performance and durability. To increase our understanding of space environmental effects on spacecraft materials, NASA Glenn Research Center has developed a series of experiments flown as part of the Materials International Space Station Experiment (MISSE) missions on the exterior of the International Space Station (ISS). Four Glenn experiments with 365 flight samples were flown on ISS’s MISSE-Flight Facility (MISSE-FF). These experiments are the Polymers and Composites Experiment-1 (PCE-1) flown as part of the MISSE-9 mission, the PCE-2 flown as part of the MISSE-10 mission, the PCE-3 flown as part of the MISSE-12 and MISSE-15 missions, and the PCE-4 flown as part of the MISSE-13 mission. The PCE 1-4 flight samples were flown in either ram, wake, zenith or nadir flight orientations. The primary objectives of the PCE 1-4 experiments are to determine the LEO atomic oxygen (AO) erosion yield, Ey (volume loss per incident oxygen atom) and radiation durability of spacecraft polymers, composites and coatings. In addition, each experiment has a wide variety of materials with numerous sample objectives. This presentation provides an overview of the PCE 1-4 experiments, the numerous sample collaborators, the space environmental exposure of the flight samples, and an overview of the post-flight observations and results. The results include AO fluence and contamination analyses for each mission flight orientation, erosion data for the PCE 1-4 AO Ey samples, optical property data, and tensile results for the MISSE-9 and MISSE-13 tensile samples. In addition, an introduction of results from other unique samples such as indium tin oxide (ITO) coated thermal control samples, shape memory polymer composites, melanin based composites, and specialty coatings, will be provided.

Atomic oxygen↗
NASA NTRSDate not supplied

Expanding the Horizons of Polymer Aerogels

As the Space Community endeavors to reach new heights of human exploration, materials for extreme environments are at the forefront of research. One class of materials of particular focus are polymer aerogels; lightweight solids with nanoscale pore size, high internal surface area, and extremely high porosities. These interesting properties allow aerogels to act as superior thermal insulators, IR scattering filters, sensor platforms, and vibro-acoustic mitigating materials. Polymer aerogels also have the potential to combat issues found in lunar environments such as dust and radiation mitigation. Herein, past and present research, synthesis, and applications of polymer aerogels will be discussed.

Stephanie L Vivod↗
DOE OSTI2020

Solvent depression of transition temperature to selectively stimulate actuation of shape memory polymer foams

An embodiment of the invention is a shape memory polymer (SMP) foam designed to recover its original shape through exposure to a solvent. Thermo-responsive SMPs are polymers designed to maintain a programmed secondary shape until heated above their transition temperature, upon which the polymer recovers its original, or primary, shape. The thermo-responsive SMP foam is programmed to its secondary shape prior to use, typically compression of the foam to a small volume, and remains in this programmed shape until exposed to a selected solvent such as dimethyl sulfoxide or ethyl alcohol. Upon exposure to the solvent, the transition temperature of the SMP foam decreases below the temperature of the environment and the SMP foam actuates to its primary shape. The SMP foam is tailored to actuate upon exposure to specific solvents while minimizing or preventing actuation when exposed to water or other solvents. This selective solvent actuation can be used to increase working time of a SMP foam device, that is, the time allowed for use of a device without undesired actuation, while maintaining functional SMP actuation. Solvent actuated SMP foams can be used in various applications including, but not limited to, treatment of aneurysms and arterio-venous malformations, tissue engineering, and wound healing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polymer composites for fused filament fabrication and methods of making the same

Disclosed are compositions of a fused filament fabrication (FFF) composite filament having embedded functional materials in a thermoplastic matrix. Methods of making the composite filaments are also disclosed. In one example, a FFF composite filament incorporates a MOF, in an amount greater than 10% by mass, dispersed in a matrix polymer. One example of a method of synthesizing FFF composite filaments involves mixing a suspension that has a MOF with a matrix polymer solution to yield a polymer-MOF mixture. The mixture is cast and dried into a solid composite material, which is formed a FFF composite filament having the MOF in an amount greater than 10% by mass.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Method to produce colorless, high porosity, transparent polymer aerogels

A method to produce a polymer gel includes dissolving precursors in a solvent to form a precursor solution, the precursors including polymer precursors, a stable free radical, one or more initiating radicals, and one or more stable free radical control agents, and heating the precursor solution to a temperature of polymerization to produce a cross-linked gel. A dried polymer aerogel has a Brunauer-Emmett Teller (BET) surface area over 100 m2/g, porosity of greater than 10%, visible transparency greater than 20%, color rendering index of over 20%, and average pore size of less than 100 nm.

Chintapalli, Mahati↗
DOE OSTI2020

Carbon dioxide and polymer compositions for permeability control and sealing

A method of treating a material to achieve at least one of reducing surface wettability of the material or reducing fluid transport through the material includes exposing the material to a composition including a solution of a polymer portion and carbon dioxide for a period of time. The polymer portion includes at least one of a polyfluoroacrylate or a copolymer of a fluoroacrylate and a comonomer. A pressure of the composition is maintained above the cloud point of the polymer portion at a concentration thereof in the carbon dioxide for the period of time.

Enick, Robert M.↗
DOE OSTI2021

Semi-solid electrodes with a polymer additive

Embodiments described herein relate generally to electrochemical cells having semi-solid electrodes that include a gel polymer additive such that the electrodes demonstrate longer cycle life while significantly retaining the electronic performance of the electrodes and the electrochemical cells formed therefrom. In some embodiments, a semi-solid electrode can include about 20% to about 75% by volume of an active material, about 0.5% to about 25% by volume of a conductive material, and about 20% to about 70% by volume of an electrolyte. The electrolyte further includes about 0.01% to about 1.5% by weight of a polymer additive. In some embodiments, the electrolyte can include about 0.1% to about 0.7% of the polymer additive.

Tan, Takahiro↗