Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Effects of non-uniform velocity profiles on dual jets in a crossflow

The interaction between engine exhaust jets and the freestream affects the aerodynamic and stability characteristics of VTOL aircraft during the transition from hover to forward flight. This interaction is often modeled as a simple uniform jet issuing from a flat plate into a subsonic crossflow. The distribution of pressures induced by the jet on the surface of the plate can be used to predict the lift loss and pitching moment for a full-scale aircraft. The uniform jet model has limitations because an actual turbofan engine generates a rather nonuniform exit velocity profile. The purpose of this work is to study the effect of a nonuniform velocity profile on the surface pressure distribution. The mutual interaction of dual jets also is investigated in side-by-side and tandem configurations. Detailed pressure distributions are presented for two jet-to-freestream velocity ratios of 2.2 and 4.0. One important finding is that a nonuniform jet with a high velocity periphery and a low velocity core has a higher effective velocity ratio than a uniform jet with the same mass flow.

Moore, C. L.↗

Density effects on jet characteristics in confined swirling flow

Density effects on isothermal jet mixing in confined swirling flow are investigated. The experiment is carried out with helium/air as the jet fluid in the same facility as that used by So et al. (1984) and the test conditions are chosen to be the same as before. Contrary to the homogeneous mixing results, the helium jet is preserved up to 40 jet diameters downstream. The behavior of the mean and turbulence field depends highly on the initial jet velocity. Since the jets are fully turbulent and the jet momentum fluxes for inhomogeneous mixing are less than those for homogeneous mixing, the cause of this difference in behavior is directly attributed to the combined action of density difference and swirl. In spite of this, near isotropy of the turbulence field is again observed at about 40 jet diameters downstream.

Ahmed, S. A.↗

Isolated and interacting round parallel heated jets

An experimental study of the flowfield of heated and unheated single and dual jet configurations was performed. This study of two parallel jets is unique since most previous aerodynamic structure experiments were limited to single round and two-dimensional jets. The present closely spaced dual jet geometry was motivated by the potential jet noise reduction available from this configuration. This geometry has shown promise as a method for redirecting jet noise away from ground based observers in side by side or over/under turbofan engine mountings on aircraft (Simonich et al., 1984). Since the effectiveness of this noise reduction technique is based on the existence of two independent jets, an understanding of the aerodynamics of the merging process is essential to establishing the acoustic benefits. The experimental program was structured so that Mach number, jet exit temperature, and spacing to diameter ratios could be independently varied to isolate each effect.

Simonich, J. C.↗

Application of a relativistic jet model to the study of BL Lacertae objects

The development of a relativistic jet model and its use in fitting coordinated observations of the BL Lacertae objects Mrk 180, Mrk 421, and Mrk 501 are described. This model is a modified version of one by Koenigl (1981). The present model fits show that the properties of the jets in all three objects are similar. The variation in the angle between the jet axis and the observer's line of sight accounts for the differing degrees of variability of the sources. For the case where the jet is seen close to the line of sight (Mrk 421), the Doppler enhanced nonthermal radiation dominates the optical flux. The variation of particle density and magnetic field strength along the jets is similar in all three sources, and suggests that the energy flux is dominated by the magnetic field in the inner regions and by the particle energy at large distances from the jet apex. This result is consistent with models of jets in which the Poynting flux drives particle acceleration at large jet radii.

Hutter, D. J.↗

Transition and mixing in axisymmetric jets and vortex rings

A class of impulsively started, axisymmetric, laminar jets produced by a time dependent joint source of momentum are considered. These jets are different flows, each initially at rest in an unbounded fluid. The study is conducted at three levels of detail. First, a generalized set of analytic creeping flow solutions are derived with a method of flow classification. Second, from this set, three specific creeping flow solutions are studied in detail: the vortex ring, the round jet, and the ramp jet. This study involves derivation of vorticity, stream function, entrainment diagrams, and evolution of time lines through computer animation. From entrainment diagrams, critical points are derived and analyzed. The flow geometry is dictated by the properties and location of critical points which undergo bifurcation and topological transformation (a form of transition) with changing Reynolds number. Transition Reynolds numbers were calculated. A state space trajectory was derived describing the topological behavior of these critical points. This state space derivation yielded three states of motion which are universal for all axisymmetric jets. Third, the axisymmetric round jet is solved numerically using the unsteady laminar Navier Stokes equations. These equations were shown to be self similar for the round jet. Numerical calculations were performed up to a Reynolds number of 30 for a 60x60 point mesh. Animations generated from numerical solution showed each of the three states of motion for the round jet, including the Re = 30 case.

Allen, G. A., Jr.↗

Spatially growing disturbances in a high velocity ratio two-stream, coplanar jet

The influence of cold and heated secondary flow on the instability of a two-stream, coplanar jet having a 0.7 Mach number heated primary jet for a nominal fan to primary velocity ratio of 0.68 was investigated by means of inviscid linearized stability theory. The instability properties of spatially growing axisymmetric and first order azimuthal disturbances were studied. The instability characteristics of the two-stream jet with a velocity ratio of 0.68 are very different from those of a single stream jet, and a two-stream, coplanar jet having a 0.9 Mach number heated primary jet and a cold secondary jet for a fan to primary velocity ratio of 0.30. For X/D = 1 and in comparison to the case where the velocity ratio was 0.3, the presence of the fan stream with a velocity ratio of 0.68 enhanced the instability of the jet and increased the unstable frequency range. However, the axisymmetric mode (m = 0) and the first order azimuthal mode (m = 1) have similar spatial growth rates where the velocity ratio is 0.68 while for a velocity ratio of 0.3 the growth rate of the first order azimuthal mode (m = 1) is greater. Comparing the cold and hot secondary flow results showed that for a velocity ratio of 0.68 the growth rate is greater for cold.

Miles, J. H.↗

Experiments and modeling of dilution jet flow fields

Experimental and analytical results of the mixing of single, double, and opposed rows of jets with an isothermal or variable-temperature main stream in a straight duct are presented. This study was performed to investigate flow and geometric variations typical of the complex, three-dimensional flow field in the dilution zone of gas-turbine-engine combustion chambers. The principal results, shown experimentally and analytically, were the following: (1) variations in orifice size and spacing can have a significant effect on the temperature profiles; (2) similar distributions can be obtained, independent of orifice diameter, if momentum-flux ratio and orifice spacing are coupled; (3) a first-order approximation of the mixing of jets with a variable-temperature main stream can be obtained by superimposing the main-stream and jets-in-an-isothermal-crossflow profiles; (4) the penetration of jets issuing mixing is slower and is asymmetric with respect to the jet centerplanes, which shift laterally with increasing downstream distance; (5) double rows of jets give temperature distributions similar to those from a single row of equally spaced, equal-area circular holes; (6) for opposed rows of jets, with the orifice centerlines in line, the optimum ratio of orifice spacing to duct height is one-half the optimum value for single-side injection at the same momentum-flux ratiol and (7) for opposed rows of jets, with the orifice centerlines staggered, the optimum ratio of orifice spacing to duct height is twice the optimum value for single-side injection at the same momentum-flux ratio.

Holdeman, James D.↗

Initial turbulence effect on jet evolution with and without tonal excitation

The effect of initial turbulence level on the development of a jet and on the susceptability of the jet to discrete tone excitation was experimentally investigated. Turbulence intensity was varied, over the range 0.15 to 5 percent, by using screens and grids placed upstream of an 8.8 cm diameter nozzle. Top-hat mean velocity profiles with approximately identical initial boundary layer states were ensured in all cases; the turbulence spectra were broadband. It was found, contrary to earlier reports, that the natural jet decay remained essentially unchanged for varying initial turbulence. For a fixed amplitude of the tonal excitation, increasing the initial turbulence damped out the growth of the instability wave; as a result, the excitability, assessed from the mean velocity decay on the axis, was found to diminish. However, the degree of damping in the amplification of the instability wave was only slight compared to the large increase in the initial turbulence. The jet with 5 percent turbulence could be measurably altered by excitation with a velocity perturbation amplitude as little as 0.25 percent of the jet velocity. The amplitude effect data indicate an upper bound of the extent to which a jet could be excited, and thus its plume shortened, by the plane wave, single frequency excitation. An additional data set with no grid or trip, yielding a nominally laminar boundary layer, re-emphasizes the profound effect of initial boundary layer state on jet evolution as well as on its excitability. This jet decayed the fastest naturally, and consequently, it was the least excitable in spite of its turbulence being the least.

Raman, G.↗

Spatially growing disturbances in a high velocity ratio two-stream, coplanar jet

The influence of cold and heated secondary flow on the instability of a two-stream, coplanar jet having a 0.7 Mach number heated primary jet for a nominal fan to primary velocity ratio of 0.68 was investigated by means of inviscid linearized stability theory. The instability properties of spatially growing axisymmetric and first order azimuthal disturbances were studied. The instability characteristics of the two-stream jet with a velocity ratio of 0.68 are very different from those of a single stream jet, and a two-stream, coplanar jet having a 0.9 Mach number heated primary jet and a cold secondary jet for a fan to primary velocity ratio of 0.30. For X/D = 1 and in comparison to the case where the velocity ratio was 0.3, the presence of the fan stream with a velocity ratio of 0.68 enhanced the instability of the jet and increased the unstable frequency range. However, the axisymmetric mode (m = 0) and the first order azimuthal mode (m = 1) have similar spatial growth rates where the velocity ratio is 0.68 while for a velocity ratio of 0.3 the growth rate of the first order azimuthal mode (m = 1) is greater. Comparing the cold and hot secondary flow results showed that for a velocity ratio of 0.68 the growth rate is greater for cold.

Miles, Jeffrey H.↗

An experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two dimensional flow.

Rodman, L. C.↗

Acoustically excited heated jets. 2: In search of a better understanding

The second part of a three-part report on the effects of acoustic excitation on jet mixing includes the results of an experimental investigation directed at resolving the question of poor excitability of some of the heated jets. The theoretical predictions discussed in Part 1 are examined to find explanations for the observed discrepancies between the measured and the predicted results. Additional testing was performed by studying the self excitation of the shock containing hot jets and also by exciting the jet by sound radiated through source tubes located externally around the periphery of the jet. The effects of nozzle-exit boundary layer conditions on jet excitability was also investigated. It is concluded that high-speed, heated jet mixing rates and consequently also the jet excitability strongly depends on nozzle exit boundary layer conditions.

Lepicovsky, J.↗

Initial turbulence effect on jet evolution with and without tonal excitation

The effect of initial turbulence level on the development of a jet and on the susceptibility of the jet to discrete tone excitation was experimentally investigated. Turbulence intensity was varied, over the range 0.15 to 5 percent, by using screens and grids placed upstream of an 8.8 cm diameter nozzle. Top-hat mean velocity profiles with approximately identical initial boundary layer states were ensured in all cases; the turbulence spectra were broadband. It was found, contrary to earlier reports, that the natural jet decay remained essentially unchanged for varying initial turbulence. For a fixed amplitude of the tonal excitation, increasing the initial turbulence damped out the growth of the instability wave; as a result, the excitability, assessed from the mean velocity decay on the axis, was found to diminish. However, the degree of damping in the amplification of the instability wave was only slight compared to the large increase in the initial turbulence. The jet with 5 percent turbulence could be measurably altered by excitation with a velocity perturbation amplitude as little as 0.25 percent of the jet velocity. The amplitude effect data indicate an upper bound of the extent to which a jet could be excited, and thus its plume shortened, by the plane wave, single frequency excitation. An additional data set with no grid or trip, yielding a nominally laminar boundary layer, re-emphasizes the profound effect of initial boundary layer state on jet evolution as well as on its excitability. This jet decayed the fastest naturally, and consequently, it was the least excitable in spite of its turbulence being the least.

Raman, G.↗

The collective emission of electromagnetic waves from astrophysical jets - Luminosity gaps, BL Lacertae objects, and efficient energy transport

A model of the inner portions of astrophysical jets is constructed in which a relativistic electron beam is injected from the central engine into the jet plasma. This beam drives electrostatic plasma wave turbulence, which leads to the collective emission of electromagnetic waves. The emitted waves are beamed in the direction of the jet axis, so that end-on viewing of the jet yields an extremely bright source (BL Lacertae object). The relativistic electron beam may also drive long-wavelength electromagnetic plasma instabilities (firehose and Kelvin-Helmholtz) that jumble the jet magnetic field lines. After a sufficient distance from the core source, these instabilities will cause the beamed emission to point in random directions and the jet emission can then be observed from any direction relative to the jet axis. This combination of effects may lead to the gap turn-on of astrophysical jets. The collective emission model leads to different estimates for energy transport and the interpretation of radio spectra than the conventional incoherent synchrotron theory.

Baker, D. N.↗

Numerical simulations of the bending of narrow-angle-tail radio jets by ram pressure or pressure gradients

Three-dimensional numerical hydrodynamic simulations are used to study the bending of radio jets. The simulations are compared with observations of jets in narrow-angle-tail radio sources. Two mechanisms for the observed bending are considered: direct bending of quasi-continuous jets by ram pressure from intergalactic gas and bending by pressure gradients in the interstellar gas of the host galaxy, the pressure gradients themselves being the result of ram pressure by intergalactic gas. It is shown that the pressure gradients are much less effective in bending jets, implying that the jets have roughly 30 times lower momentum fluxes if they are bent by this mechanism. Ram-pressure bending produces jets with 'kidney-shaped' cross sections; when observed from the side, these jets appear to have diffuse extensions on the downstream side. On the other hand, pressure-gradient bending causes the jets to be densest near their upstream side.

Soker, Noam↗

Centerline Mach number characteristics of highly heated free jets

This paper describes a detailed experimental study of Mach number centerline characteristics of highly heated free jets. The jet characteristics were obtained at a range of jet Mach numbers from 0.1 to 0.9 and jet total temperatures up to 900 K. The results show that a strong correlation exists between nozzle-exit boundary-layer conditions and free-jet development. It is clear from this investigation that experimental data on free-jet development cannot be meaningfully compared from one facility to another without specific knowledge of nozzle exit conditions. It was concluded that direct effect of the jet operating conditions (elevated flow temperature) on free jet development is much less important than the indirect effect of changed nozzle-exit boundary-layer characteristics.

Lepicovsky, Jan↗

Experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two-dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two-dimensional flows.

Rodman, L. C.↗

A linear shock cell model for jets of arbitrary exit geometry

The shock cell structures of single supersonic non-ideally expanded jets with arbitrary exit geometry are studied. Both vortex sheets and realistic mean profiles are considered for the jet shear layer. The boundary element method is used to predict the shock spacing and screech tones in a vortex sheet model of a single jet. This formulation enables the calculations to be performed only on the vortex sheet. This permits the efficient and convenient study of complicated jet geometries. Results are given for circular, elliptic and rectangular jets and the results are compared with analysis and experiment. The agreement between the predictions and measurements is very good but depends on the assumptions made to predict the geometry of the fully expanded jet. A finite diffference technique is used to examine the effect of finite mixing layer thickness for a single jet. The finite thickness of the mixing layer is found to decrease the shock spacing by approximately 20 percent over the length of the jet potential core.

Morris, P. J.↗

Numerical simulations of magnetized jets

The present axisymmetric numerical simulations of light hypersonic jets allow unmagnetized jets and jets carrying a dynamically important magnetic field to be contrasted. After decelerating a weakly magnetized jet through a series of weak, oblique shocks, a Mach disk and a strong annular shock are encountered near the outer edges of the contact discontinuity separating the shocked fluid from the shocked ambient gas. Upon passing the annular shock, the gas quickly expands and enters a backflowing cocoon surrounding the jet. The overall speed of advance of the jet is reduced; matter near the jet axis which passes through the terminal Mach disk accumulates in a plug, and gas is discharged into the cocoon by the intermittent shedding of vortices. When magnetic stresses dominate, however, the jet is rapidly decelerated via a Mach disk and strong annular shock.

Lind, Kevin R.↗