SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In support of NASA's Exploration Mission low-temperature scientists and engineers have investigated the process of extracting volatile materials from the lunar regolith, their purification/liquefaction, and storage.
Single-walled carbon nanotubes (SWCNTs) prepared by the HiPco process were purified using a modified gas phase purification technique. A TEM-STM holder was used to study the morphological changes of SWCNT ropes as a function of applied voltage. Kink formation, buckling behavior, tubular transformation and eventual breakdown of the system were observed. The tubular formation was attributed to a transformation from SWCNT ropes to multi-walled carbon nanotube (MWCNT) structures. It is likely mediated by the patching and tearing mechanism which is promoted primarily by the mobile vacancies generated due to current-induced heating and, to some extent, by electron irradiation.
Doping in cadmium telluride (CdTe) thin-film solar cells is a critical step in producing highly efficient CdTe solar modules. To date, copper (Cu) ex-situ diffusion doping and group V in situ doping (such as arsenic, As) have been effectively used in manufacturing CdTe solar modules. However, Cu doping is prone to rapid degradation, whereas the low activation ratio of the dopants constrains group V in situ doping. Recently, ex-situ group V doping has been developed, showing an improved doping activation ratio through a solution process. Here, in this study, we developed a vapor-based AsCl 3 doping method for diffusion doping of polycrystalline CdSeTe devices. AsCl 3 vapor annealing can promote the diffusion of As into the bulk CdSeTe through a surface chemical reaction between CdTe and AsCl 3 . This approach has led to a long carrier lifetime of over 72 ns, V oc of 850 mV, and power conversion efficiency of ~18% with Au metal electrodes. The vapor-based ex situ group V doping approach offers an effective means to perform group V diffusion doping into the CdSeTe device.
Chalcogenide superionic sodium (Na) conductors are great potential as solid electrolytes (SEs) in all-solid-state Na batteries with advantages of high energy density and safety, and cost effectiveness. For solid Na-ion conductors, their crystal structures and ionically conductive properties are strongly influenced by the synthetic approaches and processing parameters. Thus, understanding the synthesis process is essential to control the structures and phases and thereby yields to Na-ion conductors with desirable properties. Thanks to the high-flux and deep-penetrating time-of-flight neutron diffraction (ND), we employed in situ experiments to track real-time structural changes of two chalcogenide SEs (Na 3 SbS 4 and Na 3 SbS 3.5 Se 0.5 ) during the solid-state synthesis. For these two conductors, the ND results reveal a fast one-step reaction for the synthesis and the molten process when heating up, and the recrystallization as well as the cubic-to-tetragonal phase transition up on cooling. Moreover, Se-doping is found to influence the reaction temperatures, lattice parameter and structure stability based on neutron experimental observations and theoretical simulation. This work presents a detailed structural study using in situ neutron diffraction technology for the solid synthesis process of chalcogenide Na-ion conductors, beneficial for the design and synthesis of new solid-state conductors.
This article proposes a generalizable, data-driven framework for qualifying laser powder bed fusion additively manufactured parts using part-specific in situ data, including powder bed imaging, machine health sensors, and laser scan paths. To achieve part qualification without relying solely on statistical processes or feedstock control, a sequence of machine learning models was trained on 6299 tensile specimens to locally predict the tensile properties of stainless-steel parts based on fused multi-modal in situ sensor data and a priori information. A cyberphysical infrastructure enabled the robust spatial tracking of individual specimens, and computer vision techniques registered the ground truth tensile measurements to the in situ data. The co-registered 230 GB dataset used in this work has been publicly released and is available as a set of HDF5 files. The extensive training data requirements and wide range of size scales were addressed by combining deep learning, machine learning, and feature engineering algorithms in a relay. The trained models demonstrated a 61% error reduction in ultimate tensile strength predictions relative to estimates made without any in situ information. Lessons learned and potential improvements to the sensors and mechanical testing procedure are discussed.
In situ electrochemical Scanning Transmission Electron Microscopy (ec-S/TEM) probes the dynamics of electrochemical processes in real time and at high spatial resolution. This method utilizes microfabricated electrochemical cells, with enclosed dimensions of 800 μm wide, 800 μm long, and 1–2 μm tall, with electron-transparent silicon nitride windows. Working, counter, and reference electrodes in the configuration studied are deposited Pt with a planar surface area of about 1 μm 2 and a height of 50 nm. The cell confines the electrolyte within a 1 μm tall channel, and the microfabricated electrodes have a non-standard geometry, are coplanar, and are not front-facing. As such, standard assumptions of electrochemical experiments do not apply. COMSOL modeling was used to compare and contrast differences in electrochemical behavior between conventional experimental setups and the in situ ec-S/TEM cells. Cell height strongly affected voltammogram measurements: peak magnitudes and shifts correlate directly to cell height. Reactant concentration above the electrode quickly decreases during deposition, leading to a planar diffusion-dominated regime. The concentration gradient prioritizes particle growth along the thin edges of the electrode and not on the planar part of the electrode. Experiments done in the ec-S/TEM ex situ of a TEM verify the model’s accuracy.
Viking Lander meteorology measurements show that the Martian planetary boundary layer (PBL) has large diurnal and seasonal variations in pressure, wind velocity, relative humidity, and airborne dust loading. An even larger range of conditions was inferred from remote sensing observations acquired by the Mariner 9 and Viking orbiters. Numerical models indicate that these changes may be accompanied by dramatic vertical and horizontal wind shears (100 m/s/km) and rapid changes in the static stability. In-situ measurements from a relatively small number surface stations could yield global constraints on the Martian climate and atmospheric general circulation by providing ground truth for remote sensing instruments on orbiters. A more complete understanding of the meteorology of the PBL is an essential precursor to manned missions to Mars because this will be their working environment. In-situ measurements are needed for these studies because the spatial and temporal scales that characterize the important meteorological processes near the surface cannot be resolved from orbit. The Mars Environmental Survey (MESUR) Program will provide the first opportunity to deploy a network of surface weather stations for a comprehensive investigation of the Martian PBL. The feasibility and utility of a network of micro-weather stations for making in-situ meteorological measurements in the Martian PBL are assessed.
The practical application of high-capacity Li-rich cathode materials is hindered by capacity fading and voltage decay. The capacity fading and voltage decay could be effectively overcome by using water-soluble guar gum (GG) binder instead of traditional polyvinylidene fluoride (PVDF). However, the specific role of the GG binder is not clear yet, though the GG binder can significantly improve the electrochemical performance of Li-rich cathode. To understand the effect of GG binder on the morphology, microstructure of electrode and electrode/electrolyte interfaces, ex-situ scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray adsorption near edge spectroscopy (XANES), in-situ electrochemical impedance spectroscopy (EIS) were applied to comparatively study the charge-discharge processes of Li-rich Li 1.2 Ni 0.2 Mn 0.6 O 2 cathode when using GG and PVDF as binders. The results indicate that the GG binder can prevent electrode crack and active material loss, ascribing to the strong mechanical adhesion of GG binder with active material particles and current collector. It has found that the GG binder can also induce the formation of a uniform layer on Li 1.2 Ni 0.2 Mn 0.6 O 2 particles’ surface. As a consequence, both the electrolyte decomposition and the electrode corrosion were significantly inhibited. The strong chelation between Mn 2+ and polar OH group restrain Mn ion dissolution, which contributes to surface structural transformation mitigation. Here, our study reveals the role of water-soluble GG binder in reducing capacity fading and voltage decay of Li-rich material and is of great importance in design functional binders for high-performance Li-rich electrodes.
The Transformational Challenge Reactor (TCR) program plans to build most of the TCR core components through additive manufacturing (AM) processes. These processes include laser powder bed fusion (LPBF) for the metallic (316L) components and the newly developed combined process of binderjet printing and chemical vapor infiltration (CVI) for the SiC fuel matrix. Mechanical testing and characterization tasks have been carried out since the beginning of the TCR program to (1) build a property database for the AM materials that will be used in TCR core and (2) to assess the materials’ performance in TCR-relevant conditions. This document reports the outcome of the testing and characterization efforts for the fiscal year with a focus on the mechanical performance data of AM 316L stainless steel (SS). Baseline tensile testing over a wide temperature range of room temperature–600 °C was completed for the AM 316L alloy in as-built, stress-relieved, and solution-annealed conditions. The as-built 316L showed the highest strength, and the alloy after the post-build treatments showed reduced strengths in the low-strain range. However, the strength differences among the AM materials became insignificant in the later part of deformation. Furthermore, regardless of post-build processing, the AM 316L SS showed higher strength and comparable ductility when compared with wrought 316L SS. Thermal creep testing and microstructural evolution during creep deformation were also performed under selected conditions. It was found that the AM 316L steel showed the best creep resistance in the stress-relieved condition. In-situ tensile tests were performed using scanning electron microscopy and 1-ID beamline at the Advanced Photon Source to elucidate the deformation and fracture behavior of AM 316L and the evolution of crystalline stress, dislocations, and pore distribution. Using these in-situ testing data, an in-depth analysis of the roles of microstructural features in deformation and fracture processes is presented herein. The final section of the document introduces ongoing and future activities for materials testing and characterization, including irradiation effect studies and ball punch testing on AM 316L and AM IN718 alloys.
Ozone is a key constituent of the troposphere, where it drives photochemical processes, impacts air quality, and acts as a climate forcer. Large-scale in situ observations of ozone commensurate with the grid resolution of current Earth system models are necessary to validate model outputs and satellite retrievals. In this paper, we examine measurements from the Atmospheric Tomography (ATom; four deployments in 2016–2018) and the HIAPER Pole-to-Pole Observations (HIPPO; five deployments in 2009–2011) experiments, two global-scale airborne campaigns covering the Pacific and Atlantic basins. ATom and HIPPO represent the first global-scale, vertically resolved measurements of O3 distributions throughout the troposphere, with HIPPO sampling the atmosphere over the Pacific and ATom sampling both the Pacific and Atlantic. Given the relatively limited temporal resolution of these two campaigns, we first compare ATom and HIPPO ozone data to longer-term observational records to establish the representativeness of our dataset. We show that these two airborne campaigns captured on average 53 %, 54 %, and 38 % of the ozone variability in the marine boundary layer, free troposphere, and upper troposphere–lower stratosphere (UTLS), respectively, at nine well-established ozonesonde sites. Additionally, ATom captured the most frequent ozone concentrations measured by regular commercial aircraft flights in the northern Atlantic UTLS. We then use the repeated vertical profiles from these two campaigns to confirm and extend the existing knowledge of tropospheric ozone spatial and vertical distributions throughout the remote troposphere. We highlight a clear hemispheric gradient, with greater ozone in the Northern Hemisphere, consistent with greater precursor emissions and consistent with previous modeling and satellite studies. We also show that the ozone distribution below 8 km was similar in the extra-tropics of the Atlantic and Pacific basins, likely due to zonal circulation patterns. However, twice as much ozone was found in the tropical Atlantic as in the tropical Pacific, due to well-documented dynamical patterns transporting continental air masses over the Atlantic. Finally, we show that the seasonal variability of tropospheric ozone over the Pacific and the Atlantic basins is driven year-round by transported continental plumes and photochemistry, and the vertical distribution is driven by photochemistry and mixing with stratospheric air. This new dataset provides additional constraints for global climate and chemistry models to improve our understanding of both ozone production and loss processes in remote regions, as well as the influence of anthropogenic emissions on baseline ozone.
During high-speed X-ray imaging of laser surface polishing experiments of specimens of 316L stainless steel at Argonne National Lab's Advanced Photon Source, it was discovered that the induced keyhole changes shape and dimensions while crossing an engineered surface feature without altering process parameters. It was observed that the post-surface feature keyhole was deeper than that of the pre surface feature keyhole. Here, this work reports on the first in-situ observation of the effect of localized surface geometry on underlying melt pool behavior. This has implications for defect formation mechanisms during laser melting processes that rely on melt pool geometry.
Although Metal matrix composites (MMCs) are superior to most sought-after metallic alloys, their challenging fabricability has limited their widespread use in bulk-form applications. Among the many advanced fabrication techniques, Additive Manufacturing (AM), owing to its unique capabilities to produce near-net shapes, has drawn significant traction in the past two decades, especially for materials that are difficult to process using traditional methods. However, unlike pure metal/alloy systems, MMCs are highly sensitive to the processing conditions prevailing in AM techniques due to factors such as the high melting point of reinforcement particles and the potential for in-situ reactions. Therefore, it may be a while before metal matrix composites are commercially produced via AM. This review will discuss the current state-of-the-art design, fabricability, and performance of various additively manufactured MMCs. A particular focus will be on microstructural evolution and microstructure-property relationships. The most employed AM techniques, such as directed energy deposition, powder bed fusion, binder jetting, sheet lamination, and solid-state friction stir processing, are fundamentally different in terms of thermo-kinetics, forming the perspective for this review. A detailed comparison of microstructural evolution and process parameter optimization, including feedstock preparation methods and the role of machine learning and modeling among the different AM processes, is also presented. Finally, a critical evaluation of emerging AM technologies for MMCs is also provided, highlighting their potential advantages and challenges.
Oak Ridge National Laboratory (ORNL) is developing advanced spectroscopic and real-time monitoring capabilities to improve the timeliness of analytical measurements and process decisions for the 238Pu Supply Program. Reducing the time, resources, and costs associated with each production campaign is critical because overlapping campaigns will be required to meet the production goals of the National Aeronautics and Space Administration. Real-time, in situ analytical measurements in the heavily shielded hot cells at the Radiochemical Engineering Development Center (REDC) will allow for rapid process information feedback and operational benefits that help the 238Pu supply program scale-up production efforts. Noteworthy steps were taken during Campaign 5 to establish the ability to monitor processing streams in real time with spectrophotometry and a commercially available online monitoring software called The Unscrambler X Process Pulse II (PP) multivariate statistical process monitoring system by Camo Analytics (version 5.60). PP automates univariate-type calculations within the software itself and executes multivariate models built using The Unscrambler X (version 10.4 or newer). The Unscrambler is a commercially available data analysis software made by the same company. PP is composed of easy-to-use-tools for all personnel, including data scientists and technicians. The software can be used to plot analyte concentration profiles, spectral data, and other process variables in real time. All process data are represented in a single view with interactive charts useful for viewing how a process evolves over time.
The commercialization of high-energy Li-metal batteries is impeded by Li dendrites formed during electrochemical cycling and the safety hazards it causes. Here, a novel porous copper current collector that can effectively mitigate the dendritic growth of Li is reported. This porous Cu foil is fabricated via a simple two-step electrochemical process, where Cu-Zn alloy is electrodeposited on commercial copper foil and then Zn is electrochemically dissolved to form a 3D porous structure of Cu. The 3D porous Cu layers on average have a thickness of ≈14 um and porosity of ≈72%. This current collector can effectively suppress Li dendrites in cells cycled with a high areal capacity of 10 mAh cm -2 and under a high current density of 10 mA cm -2 . This electrochemical fabrication method is facile and scalable for mass production. In conclusion, results of advanced in situ synchrotron X-ray diffraction reveal the phase evolution of the electrochemical deposition and dealloying processes.
3D freeze printing (3DFP) combines drop-on-demand (DOD) inkjet printing with freeze casting to fabricate lightweight and multifunctional aerogels with customized geometries. Freeze casting is an efficient and easily implemented method capable of fabricating porous, sponge-like structures for many different applications. This process enables tailoring the microstructure of the final product (i.e., pore morphology, alignment, average size distribution, etc.) by controlling the fabrication conditions and freezing kinetics. Furthermore, its combination with DOD printing provides the capability of engineering the macrostructure without relying on a mold as reported for 3D freeze-printed aerogels made from graphene, silver nanowires, and other nanocomposites. In this paper, we performed in-situ X-ray imaging to understand the inside process dynamics in 3DFP using a commercially available colloidal silica ink. We investigated the 3DFP process with the following hierarchy: first, single droplets; then, uniform lines obtained from coalescence of droplets; and finally, three consecutive lines deposited layer by layer. With the help of X-ray imaging, the importance of the balance between material deposition and freezing rates was shown in-situ by the observation inside of the freeze front following the tip of the printed line. The effects of the substrate temperature on the elimination of undesired interfacial boundaries were also shown by the observed ice crystals penetrating from lower to upper layer.
Scuffing, a type of wear found in highly stressed or poorly lubricated contacts, is characterized by a rapid increase in friction and severe plastic deformation of the near-surface material. Scuffing has proven difficult to study because it initiates unpredictably, progresses rapidly, and typically develops within an inaccessible contact interface. Although there have been successful in-situ studies of scuffing in real-time, the transparent counter body needed for these studies changes the interactions between the surfaces and the lubricant, which affects the scuffing process in unknown ways. This paper describes the development of X-ray-compatible tribometry to study the scuffing of self-mated steels in-situ and in real-time. The method uses a crossed cylinders configuration with a thin (500 μm thick) stationary component and a small (≈200 μm) contact width to maximize X-ray interactions with atoms within the stress field generated by the contact. The resulting instrument and method are used to benchmark the scuffing response of self-mated 52,100 steel under tribologically challenging ‘oil-off’ lubrication conditions. The results demonstrate reliable scuffing in this configuration despite the relatively small contact areas and loads used. Following scuffing, gross plastic deformation was observed on both surfaces along with significant subsurface grain refinement and flow only on the stationary surface, which experienced constant contact. Interestingly, high friction initiated at specific locations of the migratory surface, which experienced intermittent contact, and then propagated across the track over time, suggesting that local conditions of the migratory surface dominated friction leading into the failure event.
Atmospheric CO 2 removal using engineered chemical processes, aka direct air capture (DAC), has become an essential component of our available portfolio for mitigating climate change. Here we describe a promising approach to DAC based on reactive crystallization of atmospheric CO 2 (RC-DAC) with aqueous guanidine and amino acid. Compared to the previously studied phase-changing DAC processes involving initial CO 2 absorption by an aqueous alkaline solvent followed by carbonate crystallization in a second step, RC-DAC combines the CO 2 absorption and carbonate crystallization into a single step. Thus, as the insoluble carbonate salts are removed from solution by crystallization, more CO 2 is pulled from the air into solution, further driving the DAC process. The RC-DAC was performed in a household humidifier as the air–liquid contactor, which can handle solid–liquid slurries effectively. The crystallization was monitored in situ by pH measurements, real-time imaging with a microscope probe, and by Raman spectroscopy, and ex situ by NMR spectroscopy, powder X-ray diffraction, and total inorganic carbonate analysis. Further, the investigation provided a detailed mechanistic picture of the RC-DAC process, involving formation of carbamate and carbonate anions in solution, followed by sequential crystallization of different guanidinium carbonate phases.
The continued search for organics on Mars will require the development of simplified procedures for handling and processing of soil or rock core samples prior to analysis by onboard instrumentation. Extraction of certain organic molecules such as amino acids from rock and soil samples using a liquid solvent (H2O) has been shown to be more efficient (by approximately an order of magnitude) than heat extraction methods. As such, liquid extraction (using H2O) of amino acid molecules from rock cores or regolith material is a prime candidate for the required processing. In this scenario, electrospray ionization (ESI) of the liquid extract would be a natural choice for ionization of the analyte prior to interrogation by one of a variety of potential analytical separation techniques (mass spectroscopy, ion mobility spectroscopy, etc.). Aside from the obvious compatibility of ESI and liquid samples, ESI offers simplicity and a soft ionization capability. In order to demonstrate that liquid extraction and ESI can work as part of an in situ instrument on Mars, we must better understand and quantify the effect salts have on the ESI process. In the current work, we have endeavored to investigate the feasibility and limitations of negative mode ESI of Martian surface samples in the context of sample salt content using ion mobility spectroscopy (IMS).