Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fracture Models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Mapping Diffuse Seismicity for Geothermal Reservoir Management with Matched Field Processing: Year 2 Report

Detecting and locating seismic events in managed underground geothermal reservoirs can become increasingly difficult during certain reservoir management operations. For example, during fluid injection procedures, large numbers of microearthquakes frequently occur during a relatively short amount of time. On seismic records, these events can overlap or have poor signal-to-noise ratios (SNR). This can obscure the onset of smaller signals and complicate the picking of seismic phases needed for earthquake location algorithms. To accurately illuminate the active areas of the underground reservoir through time however, a complete earthquake catalog down to very small magnitudes is necessary. To aid in the seismic characterization of reservoir fracture networks, we propose to complement traditional earthquake detection and location techniques with the empirical matched field processing (MFP) method. The principle of the empirical MFP method is to calculate propagation from source to receivers for pre-existing events, also called master templates. Then MFP matches the spatial structure of incoming seismicity observed by a network of sensors to master templates keyed to potential event locations. We demonstrate that empirical MFP can complement existing catalogs and techniques by using archived seismic information to increase earthquake catalog completeness. We identify and construct representative master templates using the Southern California Earthquake Data Center (SCEDC) earthquake catalog and archived waveform data of events originating within the Salton Sea Geothermal Field (SSGF). We identify 231 master events that have good quality seismic records at four or more seismic stations. We apply the empirical MFP method to continuous seismic data collected at the SSGF between November 2009 and December 2010. The MFP method successfully identified 5357 local events, while the original catalog only reported 1536 events. This increase in the number of events allows us to better determine the active fractures of the geothermal reservoir. We model the Coulomb stress change due to events between M2 – M3.5 that occurred during the January 2010 seismic swarm. Our results show a good correlation between regions of increased Coulomb stress change due to double-couple shear events on faults and the locations of subsequent microseismicity. In addition, we investigate the lower event detection magnitude threshold of our surface network using the MFP method. It clearly shows the event detection threshold is extended to include many smaller earthquakes with magnitudes down to M0.0. Therefore, we believe that the empirical MFP method, when combined with conventional methods, significantly improves network detection capabilities.

15 GEOTHERMAL ENERGY↗

An Integrated Multiscale Experimental-Numerical Analysis on Reconsolidation of Salt-Clay Mixture for Disposal of Heat-Generating Waste (Final NEUP Technical Report)

The overall purpose of this research is to improve understanding of THMC coupling effect on the reconsolidation of granular (or crushed) salt-clay mixture used for seal systems of shafts and drifts in salt repositories. This proposed work is partially motivated by the recent work on the Waste Isolation Pilot Plant (WIPP) that shows the promising sealing capability of clay-salt mixture compared to crushed salt. In particular, primary emphasis is to develop a fully integrated multiscale experiment-numerical study to determine and explain what leads to the superior sealing ability of the clay-salt mixture. These research activities are designed to seek further understanding of (1) why clay additives may enhance the fluid trapping and (2) whether this flow barrier effect may prevail under different combinations of temperature, confining pressure, deviatoric stress and other foreseeable environmental factors. If successful, this enhanced flow trapping ability of the seal provides significant improvement to the seal and repository performance and therefore make the repository safer in the long-term. The experiment component includes microstructural investigation and macroscopic tests on a reconsolidated salt-clay mixture. In the microstructural study, the goal is to (1) characterize microscopic distributions of distinct phases (e.g., clay, salt crystal boundaries, trapped brine, and pore) to examine the connectivity of the pore network inside the salt-clay mixture with different amounts of clay additive and moisture content and (2) analyze multiscale imaging data to reconstruct the polycrystalline microstructures for numerical simulations. Meanwhile, macroscopic tests are performed to analyze how clay alters the failure/creep mechanisms in the salt-clay mixture. Microscopic and macroscopic experimental observations will both be used to calibrate and validate a multiscale model that explicitly simulates the capillary and multiphase flow in the connected pores and the deformation due to the presence of intra-crystalline brine at the pore scale via a new polyhedral discrete element–lattice Boltzmann method (DEM-LBM) coupling model. The pore-scale simulations are homogenized via an upscaling procedure that converts pore-scale information (e.g. force exerted on grain boundary, sliding, pressure-solution) to continuum measures (e.g. Cauchy stress, Darcy’s flow) at each integration point in the macroscopic multiphase TMHC model. This multiscale scheme will allow coupling be- tween high-fidelity simulations of brine-salt-clay interaction and the macroscopic TMHC model. The multiscale model helps the understanding of how the trapped brine inclusion affects the pressure-solution mechanism with the presence of clay and moisture. This work brings new insight into the sealing capacity of salt-clay mixture under elevated temperature over a long period of time - a key to evaluating the potential of salt-clay mixture usage for salt repositories.

42 ENGINEERING↗

Efforts to stabilize composite localization elements

Localization finite elements seek to provide a robust framework for modeling ductile failure. They utilize the same constitutive model as the bulk material through the introduction of a length scale in a specialized deformation gradient that regularizes displacement discontinuity. Similar to many other elements, localization elements exhibit locking and associated pressure oscillations under incompressible plastic flow, which is a critical issue when attempting to model pressure-driven damage evolution. These issues can be drastically improved through what are essentially reduced integration techniques for the Jacobian and pressure, but there seem to be pressure-related instabilities that persist and are specific to localization elements. This memo summarizes recent efforts to mitigate and understand this problem, mostly for the 12-node composite wedge localization element in particular. At this point, it remains unclear whether the pressure fields within any localization element can be sufficiently stabilized in order to properly model failures that include softening or fracture.

36 MATERIALS SCIENCE↗

Probabilistic/Fracture-Mechanics Model For Service Life

Computer program makes probabilistic estimates of lifetime of engine and components thereof. Developed to fill need for more accurate life-assessment technique that avoids errors in estimated lives and provides for statistical assessment of levels of risk created by engineering decisions in designing system. Implements mathematical model combining techniques of statistics, fatigue, fracture mechanics, nondestructive analysis, life-cycle cost analysis, and management of engine parts. Used to investigate effects of such engine-component life-controlling parameters as return-to-service intervals, stresses, capabilities for nondestructive evaluation, and qualities of materials.

Watkins, T., Jr.↗

Plains tectonism on Venus - The deformation belts of Lavinia Planitia

The belts of the Lavinia Planitia region of Venus are discussed in detail with reference to high-resolution radar images from the Magellan spacecraft. Two types of deformation belts are identified: ridge belts and fracture belts. Ridge belts are composed of parallel ridges, each a few hundred meters in elevation, that are interpreted as folds. Typical fold spacings are 5-10 km. Fracture belts are dominated by intense faulting, with faults in some instances paired to form narrow grabens. The formation of ridge and fracture belts is explored using simple models.

Squyres, Steven W.↗

Structure-Property Relationships of Bismaleimides

The purpose of this research was to control and systematically vary the network topology of bismaleimides through cure temperature and chemistry (addition of various coreactants) and subsequently attempt to determine structure-mechanical property relationships. Characterization of the bismaleimide structures by dielectric, rheological, and thermal analyses, and density measurements was subsequently correlated with mechanical properties such as modulus, yield strength, fracture energy, and stress relaxation. The model material used in this investigation was 4,4'-BismaleiMidodIphenyl methane (BMI). BMI was coreacted with either 4,4'-Methylene Dianiline (MDA), o,o'-diallyl bisphenol A (DABA) from Ciba Geigy, or Diamino Diphenyl Sulfone (DDS). Three cure paths were employed: a low- temperature cure of 140 C where chain extension should predominate, a high-temperature cure of 220 C where both chain extension and crosslinking should occur simultaneously, and a low-temperature (140 C) cure followed immediately by a high-temperature (220 C) cure where the chain extension reaction or amine addition precedes BMI homopolymerization or crosslinking. Samples of cured and postcured PMR-15 were also tested to determine the effects of postcuring on the mechanical properties. The low-temperature cure condition of BMI/MDA exhibited the highest modulus values for a given mole fraction of BMI with the modulus decreasing with decreasing concentration of BMI. The higher elastic modulus is the result of steric hindrance by unreacted BMI molecules in the glassy state. The moduli values for the high- and low/high-temperature cure conditions of BMI/MDA decreased as the amount of diamine increased. All the moduli values mimic the yield strength and density trends. For the high-temperature cure condition, the room- temperature modulus remained constant with decreasing mole fraction of BMT for the BMI/DABA and BMI/DDS systems. Postcuring PMR-15 increases the modulus over that of the cured material even though density values of cured and postcured PMR were essentially the same. Preliminary results of a continuous and intermittent stress relaxation experiment for BMI:MDA in a 2:1 molar ratio indicate that crosslinking is occurring when the sample is in the undeformed state. Computer simulation of properties such as density, glass transition temperature, and modulus for the low- temperature cure conditions of BMI/MDA and BMI/DABA were completed. The computer modeling was used to help further understand and confirm the structure characterization results. The simulations correctly predicted the trends of these properties versus mole fraction BMI and were extended to other BMI/diamine systems.

Tenteris-Noebe, Anita D.↗

Durability Assessment of Various Gamma TiAl Alloys

Seven cast and one wrought gamma-alloys were ballistically impacted and tested under high cycle fatigue. The fatigue strength of each alloy was characterized as a function of initial flaw size and modeled using a threshold-based fracture mechanics approach.

Lerch, Brad↗

Dust Abrasion Damage on Martian Solar Arrays: Experimental Investigation and Opportunity Rover Performance Analysis

Here we investigate the effects of erosion and weathering that occur on III-V cover-glass interconnected cells (CICs) after exposure to Mars dust storm conditions. The durability of these materials in a Martian environment is not well characterized so we perform analogous experimentation. To replicate the dust impingement, test coupons were placed in an enclosure and sandblasted with Mars dust simulant. We show the J-V response dependency on both incident angle and exposure times. We find that the simulated Martian dust storm often results in damage to the anti-reflective coating and subsequent reduced short circuit current. Reduction in the open circuit voltage is observed, likely caused by structural damage to the crystal lattice after CIC fracture. We employ data-driven modeling to determine a performance degradation rate that is consistent with zero within uncertainty. We also quantify the soiling contribution and power degradation of the photovoltaic cells on Mars through analysis of 4.95 Martian years of report-out power conditions from the Opportunity rover. We find that atmospheric dust suspended due to a weather event does not result in instantaneous settled dust on the PV cells. We calculate via autocorrelation function that the dust settling rate is approximately 21 Sols from atmospheric dust suspension. The findings presented here deliver a realistic approximation for the insolation values and subsequent PV power expected over time on the Martian surface thus informing future dust abatement systems.

McMillon-Brown, Lyndsey↗

Dust Abrasion Damage on Martian Solar Arrays: Experimental Investigation and Opportunity Rover Performance Analysis

Here we investigate the effects of erosion and weathering that occur on III-V cover-glass interconnected cells (CICs) after exposure to Mars dust storm conditions. The durability of these materials in a Martian environment is not well characterized so we perform analogous experimentation. To replicate the dust impingement, test coupons were placed in an enclosure and sandblasted with Mars dust simulant. We show the J-V response dependency on both incident angle and exposure times. We find that the simulated Martian dust storm often results in damage to the anti-reflective coating and subsequent reduced short circuit current. Reduction in the open circuit voltage is observed, likely caused by structural damage to the crystal lattice after CIC fracture. We employ data-driven modeling to determine a performance degradation rate that is consistent with zero within uncertainty. We also quantify the soiling contribution and power degradation of the photovoltaic cells on Mars through analysis of 4.95 Martian years of report-out power conditions from the Opportunity rover. We find that atmospheric dust suspended due to a weather event does not result in instantaneous settled dust on the PV cells. We calculate via autocorrelation function that the dust settling rate is approximately 21 Sols from atmospheric dust suspension. The findings presented here deliver a realistic approximation for the insolation values and subsequent PV power expected over time on the Martian surface thus informing future dust abatement systems.

McMillon-Brown, Lyndsey↗

Design of Rigid-Flex PCB Robotics Leveraging Validated Finite Element Simulations

The use of rigid-flex printed circuit board (PCB) as primary structure has the potential to reduce the weight and volume of robotic systems. In the case of robotics for interplanetary exploration, these systems can leverage origami-inspired folding for increased mobility options and reduced storage volume. Folding rigid-flex PCB robotics can be constructed with rigid PCB connected by short Nomex fabric hinges coupled with flex PCB ribbon cables that permits enhanced system flexibility and energy dissipation to promote impact survivability. This paper presents a design methodology of rigid-flex PCB systems with an emphasis on impact resistance. The design process considers solder joint adequacy, panel bending, and fracture using a finite element (FE) model. The proposed design methodology is developed using a case study with NASA JPL's Pop-Up Folding Flat Explorer Robot (PUFFER). First, the finite-element (FE) modeling methodology is presented with consideration to both frequency and time-domain modeling applications, which include operational self-contact analysis and high impact scenarios. The time-domain impact modeling methodology utilizes hyperelastic material properties for the Nomex hinges. This modeling method is validated using image correlation of PUFFER drop tests. A flowchart is presented to guide users through a validated Abaqus modeling procedure for highly flexible rigid-flex systems. Next, a case study is presented in which PUFFER is subject to drop heights representative of falls into Lunar pits and then the design is refined for a more optimum impact performance. Finally, the results of the case study are used to inform a generalized design methodology for rigid-flex PCB robotics subject to high-impact loads with the considerations presented.

John Bell↗

Design of Rigid-Flex PCB Robotics Leveraging Validated Finite Element Simulations

The use of rigid-flex printed circuit board (PCB) as primary structure has the potential to reduce the weight and volume of robotic systems. In the case of robotics for interplanetary exploration, these systems can leverage origamiinspired folding for increased mobility options and reduced storage volume. Folding rigid-flex PCB robotics can be constructed with rigid PCB connected by short Nomex fabric hinges coupled with flex PCB ribbon cables that permits enhanced system flexibility and energy dissipation to promote impact survivability. This paper presents a design methodology of rigidflex PCB systems with an emphasis on impact resistance. The design process considers solder joint adequacy, panel bending, and fracture using a finite element (FE) model. The proposed design methodology is developed using a case study with NASA JPL’s Pop-Up Folding Flat Explorer Robot (PUFFER). First, the finite-element (FE) modeling methodology is presented with consideration to both frequency and time-domain modeling applications, which include operational self-contact analysis and high impact scenarios. The time-domain impact modeling methodology utilizes hyperelastic material properties for the Nomex hinges. This modeling method is validated using image correlation of PUFFER drop tests. A flowchart is presented to guide users through a validated Abaqus modeling procedure for highly flexible rigid-flex systems. Next, a case study is presented in which PUFFER is subject to drop heights representative of falls into Lunar pits and then the design is refined for a more optimum impact performance. Finally, the results of the case study are used to inform a generalized design methodology for rigid-flex PCB robotics subject to high-impact loads with the considerations presented.

de la Croix, Jean-Pierre↗

Erosion Behavior of Ti-hBN Multifunctional Coatings in A Custom-Made Planetary Test Rig at Extreme Lunar Temperatures

Spacecraft landings and takeoffs on the lunar surface, along with extreme temperature variations between day and night (-196 to 150° C), cause high-velocity dust impacts and erosion, resulting in the premature failure of structures. Ti/2 vol% hBN coatings were deposited using atmospheric (APS) and vacuum plasma spray (VPS) using cryo-milled powder feedstock to protect the structural components. The erosion performance of coatings at extreme lunar temperature regimes (-150 to 150° C) was evaluated in a custom-made planetary erosion test rig (PETR) at low (50 mph) and high impact velocities (250 mph). The mass loss of VPS coatings was reduced by 50% compared to the APS coatings and 40% compared to the Ti6Al4V substrate. The cryogenic temperature induces brittleness in the material, rendering it susceptible to extreme conditions of material loss. The particle impact-deformation behavior was captured using a high-speed camera to study the erosion mechanism. This analysis revealed chipping in substrates and brittle APS coatings, while particles rebounding and embedding were observed in VPS coatings. Energy calculations, aided by particle trajectory tracking from the high-speed camera, have conclusively shown that VPS coatings absorb 5–10% more energy than APS coatings during erosion tests. A modified erosion index was developed incorporating the fracture toughness and temperatures. New erosion models for brittle and ductile target materials are proposed for developing erosion-resistant material systems.

Abhijith Kunneparambil Sukumaran↗

Low Activation Joining of SiC/SiC Composites for Fusion Applications: Modeling Miniature Torsion Tests

The use of SiC and SiC-composites in fission or fusion environments appears to require joining methods for assembling systems. The international fusion community has designed miniature torsion specimens for joint testing and for irradiation in HFIR. Therefore, miniature torsion joints were fabricated using displacement reactions between Si and TiC to produce Ti3SiC2 + SiC joints with CVD-SiC that were tested in shear prior to and after HFIR irradiation. However, these torsion specimens fail out-of-plane, which causes difficulties in determining a shear strength for the joints or for comparing unirradiated and irradiated joints. A finite element damage model has been developed that indicates fracture is likely to occur within the joined pieces to cause out-of-plane failures for miniature torsion specimens when a certain modulus and strength ratio between the joint material and the joined material exists. The implications for torsion shear joint data based on this sample design are discussed.

Henager, Charles H.↗

Efforts and Innovations to Promote Data Sharing and Data Accessibility in the EGS Collab Experiments

Large-scale scientific research programs such as the EGS Collab experiments and the FORGE program play extremely important roles in advancing geothermal technologies. Such efforts involve a large number of researchers from multiple institutions, last multiple years, and generate large, complex datasets. The value of the research efforts is only realized when the datasets are used by a large community of researchers in the decades to come. A challenge is that due to the complexity of the data, it could require a user to devote a serious effort into understanding the data before the data can be effectively utilized. In the EGS Collab experiments, the team has devoted remarkable efforts and developed many innovative solutions to make the data more accessible to broader team members and future users. This paper documents the experience gained and lessons learned by the EGS Collab team in disseminating the data in the most informative and inspiring forms to maximize the value of this precious dataset. "Accessibility"in the title does not only mean making the raw data available for download. Particularly, we want to emphasize the importance of organizing, annotating, and presenting the data in ways to make it easy to digest by prospective consumers of the data.

circulation↗

LightMAT - Pediction of Aluminum/Steel Joint Failure

Develop a predictive model of dissimilar metallic spot joints and their behavior during fracture; specifically, whether the joint fractures via interfacial fracture or button pull-out as a function of alloy, sheet thickness, faying interface microstructure, and thermal-mechanical treatment of the weld nugget and heat affected zone. Having the ability to model whether a given joint structure would fracture inter-facially or via button pullout will reduce development time and provide savings to vehicle design programs. This would provide a significant step function improvement in reducing the time-to-market for this multi-material, weight-saving technology.

36 MATERIALS SCIENCE↗

Ion Size Effects on the Thermodynamic, Kinetic, and Mechanical Properties during Ion Exchange in Solid-State Electrolytes

Ion exchange offers a pathway to impose residual compressive stresses to mitigate the electro-chemo-mechanical cracking of solid-state electrolytes such as lithium lanthanum zirconium oxide. This study uses a coupled multiscale framework (integrating density functional theory (DFT), molecular dynamics (MD), and continuum modeling) to examine how exchange ion size influences stress, diffusion, fracture toughness, and electronic properties. Larger isovalent ions (Na + , Ag + , K + ) were exchanged with Li + , with DFT confirming their preference for octahedral 96h sites and a linear relationship between ion size and chemical free expansion coefficient. MD simulations reveal stress and concentration effects on exchange ion diffusivity at elevated temperatures, with Na + and Ag + maintaining favorable mobility while K + showing concentration-dependent clustering. Continuum modeling predicts the range of fracture strength improvements and the required ion exchange concentration profile. It was shown that a 5% surface exchange concentration can induce ∼0.6 GPa of surface compressive stress using Na + and ∼1.0 GPa of surface compressive stress using Ag + . On the other hand, larger ion exchange species may penalize Li + diffusivity by increasing the activation volume and activation energy. Interestingly, Na + has a negligible penalty on Li-ion diffusivity. The room temperature Li + ion diffusivity is reduced by ∼40% with Ag + ion exchange. Electronic band structure analysis shows no size-dependent change in the bandgap, though Ag + introduces localized defect states near the valence band maximum. This study highlights ion size as a key factor in optimizing LLZO properties, offering a framework to improve the solid-state battery performance.

Jagad, Harsh D. [Brown Univ., Providence, RI (Unit↗