Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Entry Systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake immersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan, Duct Modes↗
NASA NTRSDate not supplied

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan↗
DOE OSTI2024

2024 OES-Environmental 2024 State of the Science Report, Chapter 1: Marine Renewable Energy and Ocean Energy Systems-Environmental

For many countries, marine renewable energy (MRE) is the most recent entry into their renewable energy portfolio. MRE involves the generation of energy from the movement of seawater including tides, waves, and persistent ocean currents, as well as from the gradients of temperature and salinity in the oceans. Some countries also include energy generation from the open waters of large rivers as part of MRE. Each MRE resource requires a different type of device to harvest that energy, placed in the appropriate portion and depth of the ocean or large river and secured to the seabed either by weight or by anchors. At full scale, these devices are large; Figure 1.1 puts the size of these devices in the context of other technologies and well-known landmarks for scale. The MRE devices generally represent the largest devices available.

16 TIDAL AND WAVE POWER↗
NASA NTRS1990

Measurement of a zonal wind profile on Titan by Doppler tracking of the Cassini entry probe

A program, called the Cassini mission, intended to study the Saturn system by utilizing a Saturn orbiter and a probe descending to the surface of Titan, is discussed. Winds are expected to cause perturbations to the probe local horizontal velocity, resulting in an anomalous drift in the probe location and a shift in the frequency of the probe telemetry, due to the Doppler effect. By using an iterative algorithm, in which the time variation of the probe telemetry frequency is monitored throughout the descent, and the probe trajectory is updated to reflect the effect of wind on the probe location, a highly accurate relative wind profile can be recovered. By adding a single wind velocity, measured by independent means, an absolute wind profile can be obtained. However, the accuracy of the zonal winds recovery is limited by errors in trajectory, and frequency.

Atkinson, D. H.↗
NASA NTRS1973

The Viking parachute qualification test technique.

The parachute system for NASA's Viking '75 Mars lander was flight qualified in four high-altitude flight tests at the White Sands Missile range (WSMR). A balloon system lifted a full-scale simulated Viking spacecraft to an altitude where a varying number of rocket motors were used to propel the high drag, lifting test vehicle to test conditions which would simulate the range of entry conditions expected at Mars. A ground-commanded cold gas pointing system located on the balloon system provided powered vehicle azimuth control to insure that the flight trajectory remained within the WSMR boundaries. A unique ground-based computer-radar system was employed to monitor inflight performance of the powered vehicle and insure that command ignition of the parachute mortar occurred at the required test conditions of Mach number and dynamic pressure. Performance data were obtained from cameras, telemetry, and radar.

Raper, J. L.↗
NASA NTRS2015

Orion Launch Abort System Jettison Motor Performance During Exploration Flight Test 1

This paper presents an overview of the flight test objectives and performance of the Orion Launch Abort System during Exploration Flight Test-1. Exploration Flight Test-1, the first flight test of the Orion spacecraft, was managed and led by the Orion prime contractor, Lockheed Martin, and launched atop a United Launch Alliance Delta IV Heavy rocket. This flight test was a two-orbit, high-apogee, high-energy entry, low-inclination test mission used to validate and test systems critical to crew safety. This test included the first flight test of the Launch Abort System performing Orion nominal flight mission critical objectives. Although the Orion Program has tested a number of the critical systems of the Orion spacecraft on the ground, the launch environment cannot be replicated completely on Earth. Data from this flight will be used to verify the function of the jettison motor to separate the Launch Abort System from the crew module so it can continue on with the mission. Selected Launch Abort System flight test data is presented and discussed in the paper. Through flight test data, Launch Abort System performance trends have been derived that will prove valuable to future flights as well as the manned space program.

McCauley, Rachel J.↗
NASA NTRSDate not supplied

Mars 2020 Thermal Protection Systems Sizing and Development

The Mars 2020 spacecraft delivering the Perseverance Rover to Mars was planned to be a build-to-print repeat of the Mars Science Laboratory (MSL) spacecraft that delivered the Curiosity Rover to Mars in 2012. The 2020 mission would deliver a slightly higher mass at a lower entry velocity, so the mission designers were comfortable with the cost saving approach of using an already proven design. The approach used in sizing the thermal protection systems (TPS) for the various components of the MSL spacecraft included convective heating and shock layer radiation (a small contributor) on the heatshield and only convective heating on all of the aft body parts. At the time, it was assumed that the contribution of radiation from the shock layer and the wake was negligible on the aft body at Mars. In the time since the MSL spacecraft was designed, in light of new data and analysis, NASA realized the significance of radiative heating in the aftbody on vehicles entering Mars, beginning with the InSight entry. New analyses showed that the radiant heat fluxes on aft body components at Mars were of the same order or even larger than predicted convective heat fluxes. The Mars 2020 team was tasked with showing that the TPS thicknesses designed for MSL with only convective heating would survive the Mars 2020 convective plus radiative heat flux environments. Luckily, many of the MSL aft body components were sized using an extra conservative approach, often sizing for the worst environment at the lightest, thinnest structure, even though the environments and structures were not co-located. The Mars 2020 team had to more accurately evaluate the environments and structures to show that the design would close

Mars Entry↗
NASA NTRS2007

Flight Mechanics of the Entry, Descent and Landing of the ExoMars Mission

ExoMars is ESA's current mission to planet Mars. A high mobility rover and a fixed station will be deployed on the surface of Mars. This paper regards the flight mechanics of the Entry, Descent and Landing (EDL) phases used for the mission analysis and design of the Baseline and back-up scenarios of the mission. The EDL concept is based on a ballistic entry, followed by a descent under parachutes and inflatable devices (airbags) for landing. The mission analysis and design is driven by the flexibility in terms of landing site, arrival dates and the very stringent requirement in terms of landing accuracy. The challenging requirements currently imposed to the mission need innovative analysis and design techniques to support system design trade-offs to cope with the variability in entry conditions. The concept of the Global Entry Corridor has been conceived, designed, implemented and successfully validated as a key tool to provide a global picture of the mission capabilities in terms of landing site reachability.

HayaRamos, Rodrigo↗
NASA NTRS2008

Ongoing Capabilities and Developments of Re-Entry Plasma Ground Tests at EADS-ASTRIUM

During re-entry, spacecrafts are subjected to extreme thermal loads. On mars, they may go through dust storms. These external heat loads are leading the design of re-entry vehicles or are affecting it for spacecraft facing solid propellant jet stream. Sizing the Thermal Protection System require a good knowledge of such solicitations and means to model and reproduce them on earth. Through its work on European projects, ASTRIUM has developed the full range of competences to deal with such issues. For instance, we have designed and tested the heat-shield of the Huygens probe which landed on Titan. In particular, our plasma generators aim to reproduce a wide variety of re-entry conditions. Heat loads are generated by the huge speed of the probes. Such conditions cannot be fully reproduced. Ground tests focus on reproducing local aerothermal loads by using slower but hotter flows. Our inductive plasma torch enables to test little samples at low TRL. Amongst the arc-jets, one was design to test architecture design of ISS crew return system and others fit more severe re-entry such as sample returns or Venus re-entry. The last developments aimed in testing samples in seeded flows. First step was to design and test the seeding device. Special diagnostics characterizing the resulting flow enabled us to fit it to the requirements.

Jullien, Pierre↗
NASA NTRS1988

Effect of surface catalysis on heating to ceramic coated thermal protection systems for transatmospheric vehicles

This paper describes the effect of surface catalysis on the heat transfer rate to the heat shield of a typical Transatmospheric Vehicle (TAV) during ascent and atmospheric entry. Surface kinetics and optical properties obtained from arc-jet tests on candidate thermal protection systems (coated metals) were used in a reacting boundary layer code to estimate the heating distribution along the surface of a TAV. Thermochemical stability of the coatings is described in terms of reduction in emittance and loss of opacifiers from the coatings during the arc-jet tests.

Stewart, David A.↗
NASA NTRS1983

Design, development and flight test of a demonstration advanced avionics system

The design of integrated avionics suitable for general aviation was examined. The program emphasizes the use of data busing, distributed microprocessors, shared electronic displays and data entry devices, and improved functional capability. Design considerations includes cost, reliability, maintainability, and modularity. A demonstration advanced avionics system (DAAS) was designed, built, and flight tested in a Cessna 402, twin engine, general aviation aircraft. The DAAS, and the system architecture are described.

Denery, D. G.↗
DOE OSTI2012

The Impact of New Technologies on Radiation Oncology Events and Trends in the Past Decade: An Institutional Experience

Purpose: To review the type and frequency of patient events from external-beam radiotherapy over a time period sufficiently long to encompass significant technology changes. Methods and Materials: Ten years of quality assurance records from January 2001 through December 2010 were retrospectively reviewed to determine the frequency of events affecting patient treatment from four radiation oncology process steps: simulation, treatment planning, data entry/transfer, and treatment delivery. Patient events were obtained from manual records and, from May 2007 onward, from an institution-wide database and reporting system. Events were classified according to process step of origination and segregated according to the most frequently observed event types. Events from the institution-wide database were evaluated to determine time trends. Results: The overall event rate was 0.93% per course of treatment, with a downward trend over time led by a decrease in treatment delivery events. The frequency of certain event types, particularly in planning and treatment delivery, changed significantly over the course of the study, reflecting technologic and process changes. Treatments involving some form of manual intervention carried an event risk four times higher than those relying heavily on computer-aided design and delivery. Conclusions: Although the overall event rate was low, areas for improvement were identified, including manual calculations and data entry, late-day treatments, and staff overreliance on computer systems. Reducing the incidence of pretreatment events is of particular importance because these were more likely to occur several times before detection and were associated with larger dosimetric impact. Further improvements in quality assurance systems and reporting are imperative, given the advent of electronic charting, increasing reliance on computer systems, and the potentially severe consequences that can arise from mistakes involving complex intensity-modulated or image-guided treatments.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
NASA NTRS1962

LIFT CONTROL DURING ATMOSPHERE ENTRY FROM SUPERCIRCULAR VELOCITY

This paper presents an analysis of a guidance method which uses a reference trajectory. The four state variables needed to prescribe the trajectory are used as follows : Velocity is made the independent variable, and the errors in the rate-of-climb, acceleration, and range variables away from the reference are used to govern the lift. A linearized form of the motion equations is used to show that this represents a third-order control system. First- and second- order control terms (rate of climb and acceleration inputs) are shown to determine the entry corridor depth by stabilizing the trajectory so that the vehicle does not skip back out of the atmosphere or does not exceed a specified acceleration limit. The destabilizing effect that range input (the third-order control term) can have is illustrated and the results indicate that a low value of range input gain must be used at the high supercircular velocities while larger values of range input gain can be used at lower velocities. The usable corridor depth and range capability with this guidance system are demonstrated for a lifting capsule (L/D = 0.5). The practical applications of this system are illustrated with a fixed trim configuration wherein roll angle is used to command the desired lift. The results show that the guidance system requires only one reference trajectory for abort entry conditions as well as for entry conditions near the design values.

Atmosphere↗
NASA NTRS1982

Selected stability and control derivatives from the first three Space Shuttle entries

Stability and control derivative estimates obtained from the first three Space Shuttle entries are presented. The derivative estimates were obtained using the established modified maximum likelihood estimation program (MMLE3). The method of analysis used by the MMLE3 program is reviewed, the Shuttle configuration and data system are described, and the various types of maneuvers analyzed from the three entries are illustrated. Finally, the paper presents selected derivative results and compares them with predictions. Most of the flight-derived estimates agreed fairly well with predictions, considering the lack of experience in these new flight regimes. The most notable exception was the aerodynamic interference caused by firing the reaction control jets in the atmosphere. The flight results showed this interference to be considerably smaller than predicted.

Maine, R. E.↗
NASA NTRSDate not supplied

Electromagnetic Modeling of Wind tunnel Magnetic Suspension and Balance Systems

An analytical framework for the open-loop behavior of a permanent magnet element levitated within an applied magnetic field are shown, in the context of application to wind tunnel Magnetic Suspension and Balance Systems (MSBS). Various modes of motion are identified, which correlate with observed behavior of the NASA/ODU 6-inch MSBS. This system is being developed as a technology demonstrator for dynamic stability testing of atmospheric entry capsules, with possible application to a supersonic wind tunnel. The analytic equations are populated with field information from experimental measurements and a finite element model. Finally, a system simulation can provide alternative estimates of system dynamic behavior via model linearization, with preliminary comparisons presented. Taken together, the analytical framework, experimental measurement, finite element analysis, and dynamic simulation provide a complete understanding of the characteristics and behavior of the MSBS.

magnetic suspension↗
NASA NTRS2014

Vertical Spin Tunnel Testing and Stability Analysis of Multi-Mission Earth Entry Vehicles

Multi-Mission Earth Entry Vehicles (MMEEVs) are blunt-body vehicles designed with the purpose of transporting payloads from space to the surface of the Earth. To achieve high reliability and minimum weight, MMEEVs avoid using limited-reliability systems, such as parachutes, retro-rockets, and reaction control systems and rely on the natural aerodynamic stability of the vehicle throughout the Entry, Descent, and Landing phases of flight. Testing in NASA Langley's 20-FT Vertical Spin Tunnel (20-FT VST), dynamically-scaled MMEEV models was conducted to improve subsonic aerodynamic models and validate stability criteria for this class of vehicle. This report documents the resulting data from VST testing for an array of 60-deg sphere-cone MMEEVs. Model configurations included were 1.2 meter, and 1.8 meter designs. The addition of a backshell extender, which provided a 150% increase in backshell diameter for the 1.2 meter design, provided a third test configuration. Center of Gravity limits were established for all MMEEV configurations. An application of System Identification (SID) techniques was performed to determine the aerodynamic coefficients in order to provide databases for subsequent 6-degree-of-freedom simulations.

Glaab, Louis J.↗
NASA NTRS2019

High-Speed Wind Tunnel Tests of a Full-Scale Proprotor on the Tiltrotor Test Rig

The Tiltrotor Test Rig (TTR) is a NASA project, joint with the U.S. Army and Air Force, to develop a new, large scale proprotor test system for the National Full-Scale Aerodynamics Complex (NFAC). The first wind-tunnel entry was completed in November 2018 with a modern, 26-ft diameter proprotor. The primary purpose was to complete the development of the TTR, including systems integration with the NFAC. The TTR and rotor were tested up to 273 knots in axial flow. This is the highest airspeed ever achieved by a full-scale proprotor in any wind tunnel. Extensive conversion-mode data were also acquired, and hover/climb conditions were explored. Additional testing included aerodynamic tares, motor tests, thermal tests, modal vibration tests, and other checkout activities. This paper summarizes the results of the test, including examples of the most significant data.

Wind Tunnel Tests↗