Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Corrective Action Decision Document/Closure Report for Corrective Action Unit 560: Septic Systems, Nevada Test Site, Nevada, Revision 0 with ROTC 1

Corrective Action Unit 560 comprises seven corrective action sites (CASs): •03-51-01, Leach Pit •06-04-02, Septic Tank •06-05-03, Leach Pit •06-05-04, Leach Bed •06-59-03, Building CP-400 Septic System •06-59-04, Office Trailer Complex Sewage Pond •06-59-05, Control Point Septic System The purpose of this CADD/CR is to provide justification and documentation supporting the recommendation for closure of CAU 560 with no further corrective action. To achieve this, corrective action investigation (CAI) activities were performed from October 7, 2008, through February 24, 2010, as set forth in the Corrective Action Investigation Plan for Corrective Action Unit 560: Septic Systems, Nevada Test Site, Nevada, and Record of Technical Change No. 1. The purpose of the CAI was to fulfill the following data needs as defined during the data quality objective (DQO) process: •Determine whether contaminants of concern (COCs) are present. •If COCs are present, determine their nature and extent. •Provide sufficient information and data to complete appropriate corrective actions. The CAU 560 dataset from the investigation results was evaluated based on the data quality indicator parameters. This evaluation demonstrated the quality and acceptability of the dataset for use in fulfilling the DQO data needs. Analytes detected during the CAI were evaluated against final action levels (FALs) established in this document. The following contaminants were determined to be present at concentrations exceeding their corresponding FALs: •No contamination exceeding the FALs was identified at CASs 03-51-01, 06-04-02, and 06-59-04. •The soil at the base of the leach pit chamber at CAS 06-05-03 contains arsenic above the FAL of 23 milligrams per kilogram (mg/kg) and polychlorinated biphenyl (PCBs) above the FAL of 0.74 mg/kg, confined vertically from a depth of approximately 5 to 20 feet (ft) below ground surface. The contamination is confined laterally to the walls of the leach pit chamber and leach rock. The contamination present at CAS 06-05-03 within the leach pit was not feasible to remove. •The surface and subsurface soils within and surrounding the septic system at CAS 06-05-04 contained PCB concentrations above the FAL of 0.74 mg/kg. The lateral and vertical extent of COCs was determined for this CAS. Contaminated soils were removed up to within 18 ft of the building. The remaining contamination is confined to subsurface soils adjacent to and beneath Building CP-162 and was not feasible to remove. •The solid materials within the septic tank and soils immediately surrounding the inlet end of the tank at CAS 06-59-03 contained benzo(a)pyrene above the FAL of 0.21 mg/kg. The soils, tank contents, and tank were removed. Materials remaining at this CAS do not contain contamination exceeding FALs. •The solids contained within the septic tank and inlet pipe at CAS 06-59-05 contained the following contaminants above their respective FALs: PCBs, arsenic, lead, benzo(a)pyrene, and pesticides. The tank and inlet pipe contents were removed. Materials remaining at this CAS do not contain contamination exceeding FALs. Therefore, the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) provides the following corrective action recommendations: •No further action for CASs 03-51-01, 06-04-02, and 06-59-04, as no contaminants of potential concern were present that exceed FALs. •Closure in place for CAS 06-05-03 under a corrective action with a use restriction (UR) for remaining PCB- and arsenic-impacted potential source material (PSM). The UR form and map have been filed in the NNSA/NSO Facility Information Management System, the FFACO database, and NNSA/NSO CAU/CAS files. •Closure in place for CAS 06-05-04 under a corrective action with a UR for remaining PCBs in soil adjacent to and beneath Building CP-162. The UR form and map have been filed in the NNSA/NSO Facility Information Management System, the FFACO database, and NNSA/NSO CAU/CAS files. •No further action for CAS 06-59-03, as the COC of benzo(a)pyrene in soil and PSM have been removed. •No further action for CAS 06-59-05, as the COCs in PSM within the septic tank and inlet piping have been removed and the tank was filled with concrete.

54 ENVIRONMENTAL SCIENCES↗

GLBRC Soil Yearlong Incubation 13C-SIP-Lipidomics

Data package for Lipids represent a dynamic, yet stable pool of microbially-derived soil carbon This data is published under a CC0 license. The authors encourage data reuse and request attribution by referencing the below citations for the data packages and associated manuscript. Please cite as: Rempfert KR, Bell SL, Kasanke CP, Kyle JE, Hofmockel KS. 2025. GLBRC Soil Yearlong Incubation 13C-SIP-Lipidomics. [Data Set] PNNL DataHub. doi: Rempfert KR, Bell SL, Kasanke CP, Kyle JE, Hofmockel KS. 2025. MSV000097435: GLBRC soil yearlong incubation 13C-SIP-Lipidomics [Data Set] MassIVE. doi:10.25345/C57659T3K Rempfert KR, Bell SL, Kasanke CP, Kyle JE, Hofmockel KS. 2025. Lipids represent a dynamic, yet stable pool of microbially-derived soil carbon. In Prep This data package consists of compound-specific 13C SIP-lipidomics data from a yearlong tracer incubation experiment designed to investigate microbial lipid persistence in switchgrass bioenergy crop soils. In order to explore how lipid structure may modulate the persistence of C in soil lipids, we leveraged soils from two sites (Michigan - sandy texture, Wisconsin - silty texture) operated by the U.S. Department of Energy-funded Great Lakes Bioenergy Research Center (GLBRC). These sites had comparable climates, identical management practices, but contrasting soil textures, allowing us to assess the variability of lipid accrual or degradation in soils as well as provide insight regarding the degree to which edaphic properties may regulate the retention of soil lipids. Untargeted lipidomics analyses were performed to identify 13C-labeled lipids in the soil microbiome after long-term incubation. Soils were supplemented with 100 micrograms glucose per gram dry soil (99 atom % 13C or natural abundance for paired control) and incubated; samples were collected two months and one year after glucose addition. Lipid extracts (MPLEx) were analyzed by LC-MS/MS and identified using LIQUID. Calculation of isotopic enrichment of lipids was performed by targeted approach using TarMet to quantify lipid isotopologues and IsoCorrectoR to correct for natural abundance isotopes. Contents: Data package contents reported here are the first version and contain downstream analysis files for the raw LC-MS mass spectrometry files (.mzXML) deposited at the MassIVE database repository under accession MSV000097435 (80 experimental runs; 5.85 GB) | MassIVE DOI: 10.25345/C57659T3K. Support files include the additional data download 'Read Me' file containing data descriptor information. Reported data download contents are structured for compliance with project data sharing guidelines, community standards initiatives, and sponsor stakeholder policies supporting FAIR data principles. Data processing software, analysis tools, and data workflows are listed below corresponding to the host repository long-term location. Available Data Downloads (0.3 GB): "GLBRC soil yearlong incubation 13C-SIP-Lipidomics_readme.txt" - 'Read Me' data package content file (txt) "GLBRC_DataPackage_analysis files" - Data processing files (Rmd) and saved intermediate data processing outputs (rds, csv, xlsx) "GLBRC_13C_lipidomics_dataset.xlsx" - processed data in tabular format (xlsx) Linked Software: LIQUID LC-MS Analysis Software | 10.5281/zenodo.6459462 Lipid Mini-On Software Tools | 10.5281/zenodo.1492803 pmartR Omics Statistical Software | 10.5281/zenodo.6108667 xcms (v4.3.3) TarMet (v1.1.1) IsoCorrectoR (1.24.0) Funding Acknowledgments: This research was supported by an Early Career Research Program award funded by the U.S. Department of Energy, Office of Science, Office of Biological and Environmental Research (OBER) Genomic Science program under FWP 68292, FWP 07880 and EMSL Exploratory Research Project 51095. A portion of this work was performed in the William R. Wiley Environmental Molecular Sciences Laboratory, a national scientific user facility sponsored by OBER and located at Pacific Northwest National Laboratory (PNNL). PNNL is a multi-program national laboratory operated by Battelle for the DOE under Contract DE-AC05-76RLO1830.

Rempfert, Kaitlin R [Pacific Northwest National La↗

Diagnosing Open Cluster Stock 2: Member Candidates and Mass Distribution with Gaia DR2 and LAMOST

We identify 1325 member candidates of the open cluster (OC) Stock 2 using data from Gaia DR2. We use the algorithms Clusterix 2.0 and HDBSCAN to select cluster candidates and further refine the final cluster membership by defining neighbors in 5D phase space (X {sub cp}, Y {sub cp}, Z{sub cp},κ⋅μ{sub α}{sup ∗}/ϖ, κ · μ {sub δ}/ϖ). Among these candidates, less than half have G, G {sub BP}, and G {sub RP} extinctions from Gaia. When Gaia extinctions are unavailable, we compute extiction using empirical formulas and E(B − V) = 0.350. We analyze the spatial distribution and mass profile of Stock 2. Our results reveal Stock 2 is still a bound OC and we find evidence of mass segregation. By comparing initial mass functions, the present-day mass function indicates that Stock 2 is a massive stellar cluster with a mass of 4000 M {sub ⊙}. The core radius and tidal radius, calculated via the radial density profile and total mass, are 3.97 pc and 22.65 pc, respectively. Common stars between our selected member candidates and the Large Sky Area Multi-Object Fiber Spectroscopic Telescope DR7 medium-resolution catalog give a metalliclity of [Fe/H] = −0.040 ± 0.147.

47 OTHER INSTRUMENTATION↗

Progress on the experimental search for the chiral magnetic effect, the chiral vortical effect, and the chiral magnetic wave

In quantum chromodynamics, the interactions of quarks with the topological gluon field can lead to nonconservation of local parity (P) and conjugated parity (CP) , which provides a solution to the strong CP problem and a possibility to explain the asymmetry of matter-antimatter in the current universe. Under the action of a strong magnetic field, the nonconservation of P and CP can lead to the separation of particles according to their electric charges, which is called the chiral magnetic effect (CME). An observation of the CME-induced charge separation will confirm several fundamental properties of quantum chromodynamics (QCD), namely, approximate chiral symmetry restoration, topological charge fluctuation, and local parity violation. In relativistic heavy-ion collisions, there are other chiral anomalous effects similar to the CME, such as the chiral vortical effect (CVE) and the chiral magnetic wave (CMW). This review briefly summarizes the current progress of experimental research on the CME, CVE, and CMW in relativistic heavy-ion collisions.

Physics↗

Calculation of turbulent boundary layers with heat transfer and pressure gradient utilizing a compressibility transformation. Part 1: Summary report

The analysis uses a compressibility transformation and utilizes higher order closure rules to complete the transformation. By requiring that the momentum equations in differential form be satisfied at the wall and at the sublayer edge, correspondence rules are obtained which relate the variable property (VP) flow to a constant property (CP) flow in which mass transfer and pressure gradient occur simultaneously. A new CP formulation is developed and numerical results for a variety of cases are presented. Comparisons with earlier forms of the transformation and with experiment are included. For the zero pressure gradient case some differences between the various predictions are observed. For the several pressure gradient cases examined, the results are found to be essentially identical to those given by first order closure rules; i.e., by a form of transformation which relates the VP flow to a CP flow with pressure gradient but zero mass transfer.

Economos, C.↗

Rotordynamic Instability Problems in High-Performance Turbomachinery, 1986

The first rotordynamics workshop proceedings (NASA CP-2133, 1980) emphasized a feeling of uncertainty in predicting the stability of characteristics of high-performance turbomachinery. In the second workshop proceedings (NASA CP-2250, 1982) these uncertainities were reduced through programs established to systematically resolve problems, with emphasis on experimental validiation of the forces that influence rotordynamics. In third proceedings (NASA CP-2338, 1984) many programs for predicting or measuring forces and force coefficients in high-performance turbomachinery produced results. Data became available for designing new machines with enhanced stability characteristics or for upgrading existing machines. The present workshop proceedings illustrates a continued trend toward a more unified view of rotordynamic instability problems and several encouraging new analytical developments.

Source record↗

Maximum survival capability of an aircraft in a severe windshear

The performance of constant-alpha, maximum-alpha, constant-velocity, constant-absolute-inclination, constant-climb-rate, and constant-pitch (CP) vertical-plane guidance schemes for aircraft taking off under horizontal-windshear conditions with a downdraft is compared by means of numerical simulations; the results are presented in tables and graphs, and it is found that CP guidance gives the best aircraft survivability. Optimal, gamma-guidance, and simplified-gamma trajectories are then evaluated to improve the performance of CP, and the correct selection of the feedback gain coefficient and the time delay for response to windshear onset is shown to be of great importance for maximizing survivability.

Miele, A.↗

RSRM-9 (360L009): Ballistics mass properties

The propulsion performance and reconstructed mass properties data from Thiokol's RSRM-9 motors which were assigned to the STS-36 launch are presented. The SRM propellant, TP-H1148, is a composite type solid propellant, formulated of polybutadiene acrylic acid acryonitrile terpolymer binder (PBAN), epoxy curing agent, ammonium perchlorate oxidizer and aluminum powder fuel. A small amount of burning rate catalyst (iron oxide) was added to achieve the desired propellant burn rate. The propellant evaluation and raw material information for the RSRM-9 are included. The propellant grain design consists of four segments. There is a forward segment with an eleven point star with a transition into a tapered circular perforated (CP) configuration. There are two center segments that result in a double tapered CP configuration and an aft segment with a triple taper CP configuration and a cutout for the partially submerged nozzle. The ballistic performance presented is based on the Operational Flight Instrumentation (OFI) 12.5 sample per second pressure data for the steady state and tail off portion of the pressure trace. No high sample rate pressure gauges, Development Flight Instrumentation (DFI), were used on this flight and therefore no ignition data is presented.

Drendel, Albert S.↗

Genesis of compositional characteristics of Stillwater AN-I and AN-II thick anorthosite units

Compositional variations among samples of the thick Stillwater anorthosite units are used here to model the mechanism by which the anorthosite formed. Suspended plagioclase, on reaching a volumetric crystal concentration of about 65 percent, formed a plagioclase framework here called cumulus plagioclase (CP). Within the interstices among the crystals, some plagioclase and pyroxene precipitated, producing what is here called adcumulus plagioclase and pyroxene (APP). The final materials consists mainly of plagioclase and pyroxene formed from complete crystallization of trapped supporting liquid and called intercumulus plagioclase and pyroxene (IPP). Where the CP framework was relatively open initially, bulk liquid communicated with the interior of the framework to produce APP. Where this communication with the bulk liquid stopped or was prevented initially, the intercumulus liquid froze. Where the CP framework was more tightly packed initially, a relatively higher proportion of IPP to APP was produced.

Haskin, Larry A.↗

Laser diode ignition activities at Sandia National Laboratories

The topics are presented in viewgraph form and include the following: ignition subsystems, enhanced safety, optical ordnance power densities, optical ignition factors, low energy optical ordnance program, absorptance of 2-(5-cyanotetrazolato) pentaaminecobalt(III) perchlorate (CP) near 800 nm, power dependence of doped CP, system operational electrical requirements, dopant concentration effects for different CP particle sizes, ZR/KCLO4 optical ignition thresholds, and electrostatic discharge testing.

Merson, John A.↗

Multiparameter radar and advanced microwave precipitation radiometer observations of tropical convection

Combinations of both active and passive microwave sensors have been proposed for experiments such as the tropical rainfall measuring mission (TRMM). During the summer 1991 Convection and Precipitation/Electrification Experiment (CaPE) in central Florida, both cold- and warm-rain precipitation processes were studied with the NCAR CP-2 multiparameter radar, operating at 3 and 10 GHz. The Advanced Microwave Precipitation Radiometer (AMPR), which operates at 10.7, 19.35, 37.1, and 85.5 GHz, was flown aboard NASA's ER-2 high-altitude aircraft over storms being scanned by the CP-2 radar. Top-of-atmosphere multifrequency TB from the AMPR is presented along with coincident CP-2 radar observations. Joint analysis of both radar and radiometer data sets allows refinement of new and existing precipitation retrieval techniques which will utilize the multifrequency TB from an integrated spaceborne microwave radiometer/radar system.

Vivekanandan, J.↗

X-ray emission from chemically peculiar stars

We have searched the Roentgen Satellite (ROSAT) All-Sky Survey (RASS) database at the positions of about 100 magnetic Bp-Ap stars of the helium-strong, helium-weak, silicon, and strontium-chromium subclasses. We detect X-ray sources at the positions of 10 of these stars; in four cases the X-ray emission presumably arises from an early-type companion with a radiatively driven wind, while we believe that the magnetic chemically peculiar (CP) star is the most likely X-ray source (as opposed to a binary companion) in at least three and at most five of the six remaining cases. The helium-strong stars have X-ray emission levels that are characteristic of the luminous OB stars with massive winds (log L(sub x)/L(sub bol) is about -7), whereas the He-weak and Si stars (which generally show no evidence for significant mass loss) have log L(sub x)/L(sub bol) values that can reach as high as about -6. In contrast, we find no convincing evidence that the cooler SrCrEu-type CP stars are intrinsic X-ray sources. We discuss the X-ray and radio emission properties of our sample of CP stars, and argue that both types of emission may be magnetospheric in origin; however, there is clearly not a simple one-to-one correspondence between them, since many of the magnetic stars that are detected radio sources were not detected as X-ray sources in the present survey.

Drake, S. A.↗

Chemically anomalous, pre-accretionally irradiated grains in interplanetary dust -- interstellar grains?

Ultrafine-grained matrix is a unique and fundamental building block of chondritic porous (CP) interplanetary dust particles. Most IDPs so far determined to be of cometary origin belong to the CP class. The matrix in CP IDPs is not homogeneous but rather a loose mixture of discrete single crystals (e.g., olivine, pyroxene, Fe sulfides) and polyphase grains. The petrographic diversity observed among the polyphase grains suggest that they were formed under variable physiochemical conditions. One particular class of polyphase grains are a dominant component in cometary IDPs. Although their occurrence is well documented, the terminology used to describe them is confused. They have been called many names. Here they are simply called GEMS (Glass with Embedded Metal and Sulfides). The bulk compositions of GEMS are within a factor of 3 chondritic (solar) for all major elements except C. Quantitative thin-film X-ray (EDS) analyses have shown that GEMS are systematically depleted in Mg and Si, enriched in S, Fe, and Ni, and stoichiometrically enriched in O. Electron energy-loss spectroscopy (EELS) suggests that the excess O is present as hydroxyl (-OH) groups. These same chemical 'anomalies' were observed in solar-wind-irradiated amorphous rims on the surfaces of IDPs, suggesting that the compositions of GEMS reflect prior exposure to ionizing radiation. In order to test this hypothesis, a sample of Allende (CV3) matrix was exposed to proton flux. Radiation-damaged amorphous rims on olivine and pyroxene crystals in the Allende sample were found to be depleted in Mg and Ca, enriched in S, Fe, and Ni, and stoichiometrically enriched in O. Thus, the compositions of GEMS are indeed consistent with exposure to ionizing radiation. This study suggests that chemical as well as isotopic anomalies may be used to identify presolar interstellar grains in primitive meteoritic materials.

Bradley, J. P.↗

A search for radio emission from the 'nonmagnetic' chemically peculiar stars

We have observed 23 members of the Am and HgMn subclasses of chemically peculiar (CP) stars with the Very Large Array (VLA) to search for nonthermal radio emission at levels comparable to those found for the Si and He peculiar subclasses of the CP stars by Linsky et al. (1992). This study was motivated by recent claims that magnetic fields of kilogauss strength are present in at least some of the Am and HgMn stars, contrary to previous beliefs, which would indicate that radio-emitting magnetospheres could be present in these stars. We detected none of the Am and HgMn stars as radio emitters with upper limits typically less than 0.20 mJy. Applying a correlation between radio luminosity, surface magnetic field, and effective temperature derived from previous radio studies of the Si and He peculiar CP stars, we find that the predicted radio luminosities of alpha And (an HgMn star) and Sirius (a hot Am star) are more than an order of magnitude larger than the observed upper limits, indicating that these stars lack magnetospheres, and, by inference, surface magnetic fields.

Drake, S. A.↗

Effects of Electrons, Protons, and Ultraviolet Radiation on Thermophysical Properties of Polymeric Films

The response of coated thin polymer films to ultraviolet (UV), electron and proton radiation simultaneously has been evaluated, with selected measurements in situ. Exposure was intended to simulate the electron and proton radiation environment near the Earth-Sun Lagrangian points (LI and L2) for five years and approximately 1000 equivalent solar hours (ESH) UV. These orbital environments are relevant to several potential missions such as the Next Generation Space Telescope and Geomagnetic Storm Warning, both of which may use thin film based structures for a sunshade and solar sail, respectively. The thin film candidates (12.5 micrometers thick) consisted of commercially available materials (Kapton(R) E, HN, Upilex(R) S, CP-1, CP-2, TOR-RC, and TOR-LMBP) that were metalized on one side with vapor deposited aluminum. All of the films are aromatic polyimides, with the exception of TORLMBP, which is a copoly(arylene ether benzimidazole). The films were exposed as second surface mirrors and the effects of the exposure on solar absorptance, thermal emittance, and tensile properties were determined. The in situ changes in solar absorptance from Kapton(R) and Upilex(R) were less than 0. 1, whereas the solar absorptance of TOR and CP films increased by more than 0.3 without saturating. The thermal emittance measurements also showed that the Kapton(R) and Upilex(R) materials increased only 1-2%, but the remaining materials increased 5-8%. Based on tensile property measurements made in air following the test, the failure stress of every type of polymer film decreased as a result of irradiation. The polymers most stable in reflectance, namely Upilex(R) and Kapton(R), were also the strongest in tension before irradiation, and they retained the greatest percentage of tensile strength. The films less stable in reflectance were also weaker in tension, and lost more tensile strength as a result of irradiation. The apparent failure strain (as a percent of original gage length) of every type of polymer film except TOR-RC, decreased as a result of irradiation.

Russell, Dennis A.↗

Cometary Silicates: Interstellar and Nebular Materials

Evidence for interstellar material in comets is deduced from IR spectra, insitu measurements of Halley, and chondritic porous interplanetary dust particles (CP IDPs). IR spectra of comets reveal the spectrally active minerals: amorphous carbon, amorphous silicates, and (in some comets) crystalline silicates. Evidence suggests amorphous silicates are of interstellar origin while crystalline silicates are of nebular origin. 10 microns spectra of comets and submicron amorphous silicate spherules in CP IDPs have shapes similar to lines-of-sight through the ISM. Thermal emission models of cometary IR spectra require Fe-bearing amorphous silicates. Fe-bearing amorphous silicates may be Fe-bearing crystalline silicates formed in AGB outflows that are amorphized through He+ ion bombardment in supernova shocks in the ISM. Crystalline silicates in comets, as revealed by IR spectra, and their apparent absence in the ISM, argues for their nebular origin. The high temperatures (less than l000 K) at which crystals form or are annealed occur in the inner nebula or in nebular shocks in the 5-10 AU region. Oxygen isotope studies of CP IDPs show by mass only 1 % of the silicate crystals are of AGB origin. Together this suggests crystalline silicates in comets are probably primitive grains from the early solar nebula.

Wooden, Diane H.↗

Modeling transport kinetics in clinoptilolite-phosphate rock systems

Nutrient release in clinoptilolite-phosphate rock (Cp-PR) systems occurs through dissolution and cation-exchange reactions. Investigating the kinetics of these reactions expands our understanding of nutrient release processes. Research was conducted to model transport kinetics of nutrient release in Cp-PR systems. The objectives were to identify empirical models that best describe NH4, K, and P release and define diffusion-controlling processes. Materials included a Texas clinoptilolite (Cp) and North Carolina phosphate rock (PR). A continuous-flow thin-disk technique was used. Models evaluated included zero order, first order, second order, parabolic diffusion, simplified Elovich, Elovich, and power function. The power-function, Elovich, and parabolic-diffusion models adequately described NH4, K, and P release. The power-function model was preferred because of its simplicity. Models indicated nutrient release was diffusion controlled. Primary transport processes controlling nutrient release for the time span observed were probably the result of a combination of several interacting transport mechanisms.

NASA Center JSC↗