Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Mesoscopic analyses of the impact of morphology and operating conditions on the transport resistances in a proton-exchange-membrane fuel-cell catalyst layer

Exploring the origins of local transport resistance and characterizing the oxygen transport resistances in the catalyst layer (RCL) are critical for cost reduction. In this paper, a comprehensive mesoscopic model for simulating coupled transport processes of oxygen and water vapor for different structural parameters under different operating conditions in reconstructed microstructures is proposed. The local transport resistance is calculated after achieving the limiting current density and the effective diffusivity of oxygen. The results demonstrate that RCL increases greatly with decreasing platinum loading (LPt) and the transport resistances in other components of the cell dominate for high-loadings. Both the reduced oxygen permeation coefficient in the ionomer thin-film and the adsorption resistance account for the origins of local transport resistance. The local transport resistance increases with the bare carbon ratio for a constant LPt and Pt/C ratio due to the decreased effective ionomer surface, and increases with the I/C ratio due to the increased ionomer thickness and decreased Knudsen diffusivity. Due to the presence of liquid water, a slight decrease followed by an increase of the local transport resistance versus relative humidity is obtained. The contribution of ionomer thin-films to RCL is more sensitive to liquid saturation compared with that of pores. This journal is

Mu, YT↗
DOE OSTI2024

Digital bead modeling for wire-arc directed energy deposition

Prediction of 2D cross-section and full 3D geometry for stacked weld beads is critical for the outcome of wire-arc directed energy deposition (DED) parts; however, most additive path planning software packages model beads as extrusions of a rectangle. Weld beads are not rectangular, and the resulting shape is dependent upon physics effects at the moment of deposition. Physics phenomena such as the geometry of the underlying surface, the heat input of the welding mode, and the direction of gravity contribute to bead shape. Here, this paper presents a novel implicit modeling method that discretizes a 2D area or 3D volume of space into pixels or voxels and constructs fields based on these physics phenomena. The fields are combined using a weighting scheme trained on 3D scan measurements of welds and wire-arc DED prints. Pixels or voxels are added until the known amount of deposited volume has been achieved. Thereby, a strong conservation of mass principle is applied to the process. Utilizing machine learning techniques, the present model can be trained on a database of scans allowing for the representation of a wide variety of prints. Results show that this method can produce predictions with realistic bead morphology and sub-millimeter form error.

Bead geometry modeling↗
DOE OSTI2022

Capillary Water in 2-D Drying-Cracking Soil Sub-Grain Models: Morphology and Kinematics of Evaporation and Haines Jumps

Morphing of capillary water during the drying of a cluster of three wet grains is imaged and measured. The uniqueness of the tests is in the grains being long cylinders to make the system as close to a 2-D one as possible. In this way, the Laplace pressure depends on the only one curvature of the meniscus, which can easily be followed and is continuously image processed. The motion of liquid/gas interface, and its rate, as well as of contact angle and perimeter, are also monitored. The drying water body has been known to undergo two modes of re-morphing: a slow, evaporation rate-controlled one and a fast, inertia-driven instabilities of the interfaces. Two particular forms of dynamic re-morphing are being followed: one, called classically an “air entry,” which is a meniscus jump before its approaching the throat between the top and a bottom grain and another jump of the bottom contact, with a splitting of the meniscus into two between only two of the three grains. Associated dynamic variables, capillary pressure, and surface tension forces developing prior to and in conjunction with the instabilities of the menisci are presented in a companion paper by Hueckel et al..

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

A quantitative comparison of the fingerprint of twinned microstructures through surface and three-dimensional techniques

Assessing the fingerprint of a material’s microstructure is key for supporting materials design. With the emergence of a wide range of 3D characterization techniques, it is critical to understand the main differences in fingerprints reconstructed from 2D and 3D datasets. To this end, we introduce a graph-based microstructure reconstruction framework that enables structural comparisons of twin domain networks in high purity Ti using 3D and 2D electron backscatter diffraction. Insights into the structure of the twin networks are facilitated by combining statistical analysis of twin crystallography with visual and graphical analysis of the novel graph abstractions of the twins. We demonstrate that compared to 3D reconstructions, conventional 2D views of twinning miss key aspects of the microstructure including the high interconnectivity of domains into networks that span the full reconstruction volume. The reduced cross-grain and in-grain twin connectivity typically observed in 2D has notable implications on our understanding of how twinning mediates the plastic response of microstructures and how twin networks evolve. It is thus clear that 3D characterization is critical for accurately inferring both twin network morphologies as well as the key unit processes facilitating network formation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Characterization of Annealing-Induced Phase Segregation in Composite Silicon Anodes for Li-ion Batteries

Silicon (Si) anodes present a promising alternative to graphite anodes for lithium-ion batteries (LIBs), as Si has a greater specific capacity. However, one major constraint is the volumetric change of Si during lithiation that results in an unstable solid-electrolyte interphase (SEI), so Si-containing electrodes require the use of various strategies to mitigate these effects and improve performance. One such solution is the use of Si nanoparticles (NPs) that maximize the surface area to volume ratio. Here, we discuss electrodes made with Si NPs treated with polyethylene oxide (PEO) (for improving dispersion during processing), conductive carbon NPs, and P84 polyimide binder which shows significant impacts of annealing treatment on improvements of active material utilization, first cycle efficiency, and capacity retention with extensive cycling . We used air-free argon ion polishing to create electrode cross sections and imaged through the electrode thickness using atomic force microscopy (AFM)-based nano-electrical characterization of scanning spreading resistance microscopy (SSRM), nano-mechanical characterizations of contact resonance and force volume (CR-FV), and scanning electron microscopy-based energy dispersive x-ray spectroscopy (SEM-EDS). Results show that the Si and conductive carbon segregate into phases with a distinctive carbon-rich banded morphology that surrounds the Si-rich phase during annealing. In pristine electrodes, the carbon- and SEI-rich bands exhibit a higher electronic conductivity and a lower elastic modulus than the Si active material phase. These structures, as well as distinct electronic and mechanical properties, remain during cycling, suggesting an improvement of electrical conduction pathways and a mechanical strain buffer for active Si material expansion during cycling. This phase separation may be a major factor in the improvement seen in electrochemical performance due to annealing. Additionally, our nm-scale and multi-mode characterizations provide a novel route for understanding and improving energy storage devices, which is advantageous due to the highly inhomogeneous of composite electrodes in nm-mm scales.

ENERGY STORAGE↗
DOE OSTI2023

Aerosol Manufacturing Technology to Produce Low-Cobalt Li-ion Battery Cathodes

Although considerable progress has been made with battery materials over the last 10 years, the cathode remains a major performance-limiting material in Li-ion battery (LIB) technology. New materials and battery chemistries will overcome some of the remaining challenges, but cathode materials must also be manufactured at a lower cost and with a smaller environmental footprint using new processes that can also enable improved control over stoichiometry, morphology, and compositional homogeneity. Cabot, Argonne National Laboratory and SAFT research teams are combining their extensive expertise in particle synthesis, battery materials and cell design to develop a low-cost, flexible aerosol manufacturing technology for production of high-performance cathode active materials (CAM). This project will develop low-Co CAMs via Reactive Spray Technology (RST) and Flame Spray Pyrolysis (FSP) to reach performance targets of < 50 mg Cobalt/Wh.

25 ENERGY STORAGE↗
DOE OSTI2022

Dual-scale folding in cutting of commercially pure aluminum alloys

We examine a, hitherto, little-studied and curious machining chip morphology, with tell-tale signs of folding at two different length scales, that is common in cutting of certain ductile and highly strain-hardening metals like soft aluminum alloys, tantalum and niobium. This chip morphology does not appear in the usual catalogues of common chip types. The mechanics of formation of the “dual-scale folded chip” is studied in model material systems of commercially pure aluminum alloys (AA 1100 and AA 8040), that prominently exhibit this chip morphology. The flow, folding and associated plastic instabilities are investigated using micro/macro structure observations of the chip in a plane-strain cutting framework, with high-speed in situ imaging and image analysis of material flow; and force measurements. The smaller-scale folding is shown to develop in the primary deformation zone while the larger-scale folding occurs as the chip traverses the rake face of the tool. The resulting chip is composed of irregularly-spaced large folds, superimposed onto which are the quasi periodic small folds. The representative wavelengths of the two folds differ on average by an order of magnitude, 0.1 mm vs. 2 mm. The observations reveal a direct coupling between the material flow and chip morphology, and how specific attributes of the dual-scale folded chip arise from the flow mechanism. Plastic buckling is found to play a key role in the folding at both length scales. The small-scale folds are characteristic of a sinuous plastic flow mode, while the large-scale folding is characterized by buckling and stick-slip along the tool rake face, triggered by adhesive pinning of the chip to the tool. Important consequences of the dualscale folding are very large cutting forces, and force oscillations of large amplitude, despite the alloys being very soft, only ~ 25 HV. Here, the dual-scale folding is why many of these alloys are classified as “gummy” to machine. Since the dual-scale folded chip is associated with large cutting forces and poor surface quality, there is much to be gained by disrupting this flow type in practical machining applications. Methods for controlling the folding to improve machining performance with the gummy alloys are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Revealing the Nanostructure of Mesoporous Fuel Cell Catalyst Supports for Durable, High-Power Performance

Achieving high power performance and durability with low Pt loadings are critical challenges for proton exchange membrane fuel cells. PtCo catalysts developed on new carbon black supports show promise by simultaneously providing good oxygen reduction kinetics and local oxygen transport. We investigate the role of nanoscale morphology in the performance of these catalysts supported on accessible (HSC-e and HSC-f) and conventional (Ketjen Black) porous carbons using 3D electron tomography, nitrogen sorption, and electrochemical performance measurements. We find that the accessible porous carbons have hollow interiors with mesopores that are larger and more numerous than conventional porous carbons. However, mesopore-sized openings (>2 nm width) are too rare to account for significant oxygen transport. Instead we propose the primary oxygen transport pathway into the interior is through 1–2 nm microporous channels permeating the carbon. The increased mesoporosity in the accessible porous carbons results in a shorter diffusion pathlength through constrictive, tortuous micropores in the support shell leading to lower local oxygen transport resistance. In durability testing, the accessible porous carbons show faster rates of electrochemical surface area loss, likely from fewer constrictive pores that would mitigate coarsening, but maintain superior high current density performance at end of test from the improved local oxygen transport.

Electrochemistry↗
DOE OSTI2020

Spent Crystalline Silicotitanate Storage Study

Washington River Protection Solutions is working to support initial production of immobilized low-activity waste (LAW) by feeding Hanford tank supernate from tank farms to the Hanford Waste Treatment and Immobilization Plant (WTP) LAW Facility. This goal incorporates the design of a Tank-Side Cesium Removal (TSCR) system, which filters tank waste supernate to remove suspended solids and then removes Cs by processing it through crystalline silicotitanate (CST) ion exchange media manufactured by Honeywell UOP, LLC. The 137 Cs-depleted product is intended to be sent to the WTP for vitrification. The Cs-loaded CST columns will be stored indefinitely, with a goal of eventual CST removal and treatment. Thus, the spent CST needs to be recoverable. The testing described herein looks to potential upset process conditions where CST storage may be required before various rinse steps are completed. This study evaluated upset conditions at three sequential processing steps envisioned for TSCR (feed, 0.1 M NaOH rinse, water rinse), and in-column drying with compressed air (normal end step) to assess impacts on the nature of the CST bed. Testing was conducted at the small scale (12-mL bed volume); simulated AP-105 tank waste was used as the feed. Following process disruption, the CST bed was dried in place at 70 °C. Post-dried CST bed physical properties (angle of repose, penetration depth, particle morphological changes) were measured to evaluate how CST moved and flowed. The testing is intended to provide a preliminary assessment of issues that may arise from desiccation of CST with the indicated salt solutions in place. Since these were small-scale tests, the processing conditions will not match full scale conditions exactly; however, the tests do provide insight into the impact of stopping processing at an earlier step than normal. Except for the feed that was dried in-place, all other process stop-conditions showed the CST bed flowed well after drying. At this small scale, CST beds would not present an issue for retrievability. The feed that was dried in place had solidified into a rock-hard monolith with no movement possible. Samples had to be chipped from the surface.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Rheological and microstructural characterization of aqueous suspensions of carbon black and reduced graphene oxide

Carbon black is often used as a conductivity enhancer in battery electrodes. Reduced graphene oxide is another conducting material, with a high aspect ratio sheet-like morphology, and offers the possibility of generating a conducting network at loadings that are small compared to carbon black. Suspensions of conducting carbon, active materials and binders are typically coated on current collectors during the formation of electrodes. The rheology of these suspensions is an important indicator of the connectivity of particles in the suspension and impacts the electrical conductivity as well as the thickness of the coated layer. In this work, the rheology and microstructures of aqueous suspensions of para-aminobenzoic acid terminated carbon black (CB) with and without reduced graphene oxide (RGO) were investigated. The CB loading varied between 0.05 wt.% -10 wt.%, while the samples containing RGO had an RGO loading of 0.05 wt.%. The pH of the suspension was varied from 7.5 to 3. The carboxyl groups on the CB surface are deprotonated at pH 7.5, making the particles hydrophilic. Protonation of the carboxylate groups at pH 3 makes the particles partially hydrophobic. Suspensions of CB showed Newtonian behavior at all loadings for pH 7.5, and at loadings below 1.5 wt.% for pH 3. They are shear thinning at loadings between 1.5–10 wt.%. Interestingly, the low shear viscosity is non-monotonic with CB loading, rising up to a CB loading of 7.5 wt.%, and then dropping at 10 wt.%. Cryogenic scanning electron microscopy (SEM) showed CB particles forming aggregates at pH 3 for CB loadings greater than 1.5 wt.%. At pH 3, addition of 0.05 wt.% RGO resulted in a viscosity increase for suspensions containing 0.5 wt.% CB, as the RGO formed connections with CB particles that enhanced network formation. Adding RGO had little effect on suspensions that had 1.5 wt.% CB. The combination of SEM imaging and suspension rheology provides insight into the particle connectivity for the carbon-based materials studied here. These insights will be useful in determining coating conditions for slurries used in rechargeable battery electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Highly tunable structure-by-design polymer brush membranes for organic solvent nanofiltration

Synthetic polymeric nanofiltration membrane processes offer an alternate low-energy option to energy-intensive distillation to fractionate similar size organic solvents for chemical, petroleum, food and biotechnology industries. Here, in this study, we synthesize and test a new class of structure-by-design hydrophilic polymeric brush membranes, that address the limitations of commercial polymer membranes, are tunable and exhibit commercially relevant filtration performance. Because these brush membranes are grafted by Single Electron Transfer-Living Radical Polymerization (SET-LRP) and replace statistically random phase inversion or interfacial polymerization used for synthesizing commercial polymer membranes, their porous structure can be remodeled by varying their morphology and chemistry. We graft hydroxyethyl methacrylate (HEMA) brush structures with short and long crosslinkers, demonstrate two competing phenomena - pore stiffening and opening - and obtain high selectivity at reasonable permeability for commercially relevant methanol/toluene separation. This new class of stable, tunable, and scalable membranes offers exciting opportunities to reduce energy for separation of organic solvents.

42 ENGINEERING↗
DOE OSTI2019

Carbon nanotube-based mixed-matrix membranes with supramolecularly engineered interface for enhanced gas separation performance

Here in this study, novel nanocomposite membranes were fabricated from single-walled carbon nanotubes (SWNTs) and a triptycene-containing polyimide. The desirable interfacial morphology and homogenous dispersion of SWNTs were achieved by strong π-π stacking and supramolecular shape-fitting interactions between the nanotube and the paddlewheel-shaped triptycene moieties in polymer matrix. Mixed-matrix membranes (MMMs) containing 2–15 wt% of as-purchased SWNTs (AP-SWNTs) were prepared and tested for their gas transport properties. While all MMMs showed greatly enhanced permeabilities with well-maintained selectivities, a non-linear dependence of permeability on filler content was observed. Another series of MMMs with purified SWNTs (P-SWNTs) and acid-treated SWNT (A-SWNTs) were also prepared. The functionalized A-SWNT MMM exhibited the best separation performance at 2 wt% filler content among all MMMs, which can be attributed to the improved interfacial affinity with carboxylic acid functionalized surface of A-SWNTs.

42 ENGINEERING↗
DOE OSTI2022

Solution-Deposited and Patternable Conductive Polymer Thin-Film Electrodes for Microbial Bioelectronics

Microbial bioelectronic devices integrate naturally occurring or synthetically engineered electroactive microbes with microelectronics. These devices have a broad range of potential applications, but engineering the biotic–abiotic interface for biocompatibility, adhesion, electron transfer, and maximum surface area remains a challenge. Prior approaches to interface modification lack simple processability, the ability to pattern the materials, and/or a significant enhancement in currents. We report a novel conductive polymer coating that significantly enhances current densities relative to unmodified electrodes in microbial bioelectronics is reported. The coating is based on a blend of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) crosslinked with poly(2-hydroxyethylacrylate) (PHEA) along with a thin polydopamine (PDA) layer for adhesion to an underlying indium tin oxide (ITO) electrode. When used as an interface layer with the current-producing bacterium Shewanella oneidensis MR-1, this material produces a 178-fold increase in the current density compared to unmodified electrodes, a current gain that is higher than previously reported thin-film 2D coatings and 3D conductive polymer coatings. The chemistry, morphology, and electronic properties of the coatings are characterized and the implementation of these coated electrodes for use in microbial fuel cells, multiplexed bioelectronic devices, and organic electrochemical transistor based microbial sensors are demonstrated. It is envisioned that this simple coating will advance the development of microbial bioelectronic devices.

patterned bioelectronics↗
DOE OSTI2021

Reducing roughness and improving efficiency of MAPbI3 perovskite solar cells made by high-throughput photonic curing

For perovskite solar cells (PSCs) to be commercially viable, the slow and energy-insufficient thermal annealing step must be eliminated. Among the photo-irradiation methods proposed to replace thermal annealing, photonic curing is the fastest conversion method. Photonic curing delivers short (20 μs to 100 ms) but intense light pulses from a broadband (200-1500 nm) xenon flash lamp, making it the only method to convert perovskite under 20 ms. This processing time can be extrapolated to a roll-to-roll web speed of 40 m/min based on laboratory processing conditions. However, most reported PSCs made by photonic curing under 1 second have inferior performance (~10% PCE). Although SEM images show dense and pinhole-free perovskite films, AFM images indicate secondary wavy features of 500 nm-wide ridge and 80 nm-deep trenches on photonically cured perovskite films, the existence of which correlates with poor device performance. We suggest that this morphology feature is produced by volatile solvent evaporation during the fast photonic curing process. Two approaches have been made to remedy this issue: (1) adding CH2I2 as the third solvent in the conventional DMF-DMSO system and (2) applying a controlled air-blowing step before photonic curing to remove excess solvent further. Combining these two approaches produces photonically- cured perovskite films with a comparable film roughness and device performance. Alkyl halide additives have been reported to enhance PSC performance by modulated solvent-solute interactions and C-X (X = Cl, Br, and I) cleavage. Photonic curing can cleave CH2I2, producing disassociated iodide ions to replenish iodine loss induced by photonic curing, which is confirmed by EDX. As a co-solvent, the high boiling point of CH2I2 can also make the solvent less volatile, reducing surface roughness in photonically cured perovskite films. Additionally, photonically-cured perovskite films have longer PL lifetimes and a higher recombination resistance compared to thermally-annealed counterparts. As a result, we demonstrate that photonic curing is a suitable method to replace thermal annealing in high-throughput PSC fabrication.

14 SOLAR ENERGY↗
DOE OSTI2022

Intraspecific Variation for Leaf Physiological and Root Morphological Adaptation to Drought Stress in Alfalfa ( Medicago sativa L.)

Drought stress reduces crop biomass yield and the profitability of rainfed agricultural systems. Evaluation of populations or accessions adapted to diverse geographical and agro-climatic environments sheds light on beneficial plant responses to enhance and optimize yield in resource-limited environments. This study used the morphological and physiological characteristics of leaves and roots from two different alfalfa subspecies during progressive drought stress imposed on controlled and field conditions. Two different soils (Experiments 1 and 2) imposed water stress at different stress intensities and crop stages in the controlled environment. Algorithm-based image analysis of leaves and root systems revealed key morphological and physiological traits associated with biomass yield under stress. The Medicago sativa subspecies (ssp.) sativa population, PI478573, had smaller leaves and maintained higher chlorophyll content (CC), leaf water potential, and osmotic potential under water stress. In contrast, M. sativa ssp. varia, PI502521, had larger leaves, a robust root system, and more biomass yield. In the field study, an unmanned aerial vehicle survey revealed PI502521 to have a higher normalized difference vegetation index (vegetation cover and plant health characteristics) throughout the cropping season, whereas PI478573 values were low during the hot summer and yielded low biomass in both irrigated and rainfed treatments. RhizoVision Explorer image analysis of excavated roots revealed a smaller diameter and a narrow root angle as target traits to increase alfalfa biomass yield irrespective of water availability. Root architectural traits such as network area, solidity, volume, surface area, and maximum radius exhibited significant variation at the genotype level only under limited water availability. Different drought-adaptive strategies identified across subspecies populations will benefit the plant under varying levels of water limitation and facilitate the development of alfalfa cultivars suitable across a broad range of growing conditions. The alleles from both subspecies will enable the development of drought-tolerant alfalfa with enhanced productivity under limited water availability.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Hierarchical morphologies in co-sputter deposited thin films

Co-depositions of immiscible alloy films at specific processing conditions have yielded hierarchical microstructures which consist of distinct features at multiple length scales, often agglomerates and concentration modulations on the sub-micrometer-scale and fine nanoprecipitates in a matrix on the nanoscale. The present work examined a series of immiscible alloy systems: Cu-Mo, Cu-Ag, Cu-Fe, Cu-Ta, Mo-Ag, Cu-Mo-Ag, to determine the kinetic conditions favorable for hierarchical organization and the formation mechanism of such structures. Thin films of six immiscible systems were sputter co-deposited over a range of deposition rates from 0.12 to 2 nm/s and various temperatures from 400 to 800°C. The resulting microstructures indicate that hierarchical structures form with sufficient disparity in kinetic energy between the constituent atoms, one species being highly mobile (A) and the other relatively immobile (B). This condition arises typically at elevated deposition temperatures and reduced deposition rates but is also alloy dependent. The hierarchical structures form during deposition via phase separation and self-organization processes across the multiple length scales. The adatoms diffuse on the film surface with the highly mobile species swiftly agglomerating into A-rich domains within which B-rich nanoprecipitates form, often self-organizing into periodic arrays. The smallest B-rich nanoprecipitates in the A-rich domains are found to be coherent and in a metastable crystal structure (B taking the structure of A), but coarser precipitates that exhibit the equilibrium structure of B element. The A-rich domains are surrounded by a B-rich matrix that phase-separates into a concentration modulated structure. In conclusion, the observations are interpreted via a model incorporating material properties and process parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Outsourced hearing in an orb-weaving spider that uses its web as an auditory sensor

Hearing is a fundamental sense of many animals, including all mammals, birds, some reptiles, amphibians, fish, and arthropods. The auditory organs of these animals are extremely diverse in anatomy after hundreds of millions of years of evolution, yet all are made up of cellular tissue and are morphologically part of the bodies of animals. Here, we show that hearing in the orb-weaving spider Larinioides sclopetarius is not constrained by the organism’s body but is extended through outsourcing hearing to its extended phenotype, the proteinaceous, self-manufactured orb web. We find that the wispy, wheel-shaped orb web acts as a hyperacute acoustic antenna to capture the sound-induced air particle movements that approach the maximum physical efficiency better than the acoustic responsivity of all previously known eardrums. By sensing the motion of web threads, the spider remotely detects and localizes the source of an incoming airborne acoustic wave, such as those emitted by approaching prey or predators. By outsourcing its acoustic sensors to its web, the spider is released from body size constraints and permits the araneid spider to increase its sound-sensitive surface area enormously, up to 10,000 times greater than the spider itself. The spider also enables the flexibility to functionally adjust and regularly regenerate its external "eardrum" according to its needs. The outsourcing and supersizing of auditory function in spiders provides unique features for studying extended and regenerative sensing and designing novel acoustic flow detectors for precise fluid dynamic measurement and manipulation.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

High Performance PEFC Electrode Structures

Raytheon Technologies Research Center (RTRC) in collaboration with Ion Power Inc. and the University of Arkansas at Little Rock and the FC-PAD consortium executed a project that: (1) developed comprehensive models of oxygen and proton transport in cathode catalyst layers that provided new insights about losses associated with reducing platinum loading to 0.1 mg/cm 2 , (2) designed, fabricated, characterized, and tested cells featuring carbon-supported catalyst layers with low platinum loadings that met efficiency and power density targets set forth by the Hydrogen and Fuel Cells Technology Office, and (3) designed, fabricated, characterized, and tested novel catalyst structures. The modeling efforts produced eight scientific publications that shared new descriptions of oxygen and proton transport in catalyst layers with the broader technical community. The key physical insights from the models are expressed in straightforward algebraic expressions, facilitating easy adoption by other researchers. The models developed during the project explain why resistance to oxygen transport is inversely proportional to interfacial area of platinum – an observation that eluded quantitative explanation for a decade. The models quantitatively predict polarization when measured morphological parameters and transport properties are input. Membrane-electrode assemblies made during the project met stated goals for current at high voltage and power density at rated voltage for transportation fuel cells at the end of budget period 2. High performance was achieved by developing a diffusion layer with low resistance to oxygen transport and a PtCo/C cathode catalyst layer capable of supporting rapid proton and oxygen transport. The project was subsequently directed to curtail experimental work and focus on modeling during budget period 3. Ion Power Inc. developed new expertise in fabricating catalyst layers containing platinum-cobalt catalysts, and processing very thin membranes. The University of Arkansas at Little Rock developed novel nanocolumnar self-supported thin film electrocatalysts that can be grown on carbon supports using a simple high pressure sputter deposition method. The nanocolumnar microstructure provides adequate surface-to-volume ratio for efficient platinum utilization, and the conformal platinum shell with larger crystal grain sizes covering the carbon support surface may eliminate durability issues associated with catalyst dissolution, agglomeration, and carbon corrosion.

08 HYDROGEN↗