Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Satellite Estimation of Spectral Surface UV Irradiance: Effect of Horizontally Homogeneous Clouds - 2

The local variability of UV irradiance at the Earth's surface is mostly caused by clouds in addition to the seasonal variability. Parametric representations of radiative transfer RT calculations are presented for the convenient solution of the transmission T of ultraviolet radiation through plane parallel clouds over a surface with reflectivity R(sub s). The calculations are intended for use with the Total Ozone Mapping Spectrometer (TOMS) measured radiances to obtain the calculated Lambert equivalent scene reflectivity R for scenes with and without clouds. The purpose is to extend the theoretical analysis of the estimation of UV irradiance from satellite data for a cloudy atmosphere. Results are presented for a range of cloud optical depths and solar zenith angles for the cases of clouds over a low reflectivity surface R(sub s) less than 0.1, over a snow or ice surface R(sub s) greater than 0.3, and for transmission through a non-conservative scattering cloud with single scattering albedo omega(sub 0) = 0.999. The key finding for conservative scattering is that the cloud-transmission function C(sub T), the ratio of cloudy-to clear-sky transmission, is roughly C(sub T) = 1 - R(sub c) with an error of less than 20% for nearly overhead sun and snow-free surfaces. For TOMS estimates of UV irradiance in the presence of both snow and clouds, independent information about snow albedo is needed for conservative cloud scattering. For non-conservative scattering with R(sub s) greater than 0.5 (snow) the satellite measured scene reflectance cannot be used to estimate surface irradiance. The cloud transmission function has been applied to the calculation of UV irradiance at the Earth's surface and compared with ground-based measurements.

Krothov, N.↗

Spatial heterogeneity effects on land surface modeling of water and energy partitioning

Abstract. Understanding the influence of land surface heterogeneity on surface water and energy fluxes is crucial for modeling earth system variability and change. This study investigates the effects of four dominant heterogeneity sources on land surface modeling, including atmospheric forcing (ATM), soil properties (SOIL), land use and land cover (LULC), and topography (TOPO). Our analysis focused on their impacts on the partitioning of precipitation (P) into evapotranspiration (ET) and runoff (R), partitioning of net radiation into sensible heat and latent heat, and corresponding water and energy fluxes. An initial set of 16 experiments were performed over the continental US (CONUS) using the E3SM land model (ELMv1) with different combinations of heterogeneous and homogeneous datasets. The Sobol' total and first-order sensitivity indices were utilized to quantify the relative importance of the four heterogeneity sources. Sobol' total sensitivity index measures the total heterogeneity effects induced by a given heterogeneity source, consisting of the contribution from its own heterogeneity (i.e., the first-order index) and its interactions with other heterogeneity sources. ATM and LULC are the most dominant heterogeneity sources in determining spatial variability of water and energy partitioning, mainly contributed by their own heterogeneity and slightly contributed by their interactions with other heterogeneity sources. Their heterogeneity effects are complementary, both spatially and temporally. The overall impacts of SOIL and TOPO are negligible, except TOPO dominates the spatial variability of R/P across the transitional climate zone between the arid western and humid eastern CONUS. Accounting for more heterogeneity sources improves the simulated spatial variability of water and energy fluxes when compared with ERA5-Land reanalysis dataset. An additional set of 13 experiments identified the most critical components within each heterogeneity source, which are precipitation, temperature, and longwave radiation for ATM, soil texture, and soil color for SOIL and maximum fractional saturated area parameter for TOPO.

54 ENVIRONMENTAL SCIENCES↗

Microstructure-Sensitive modeling of surface roughness and notch effects on extreme value fatigue response

Fatigue life knockdown due to surface roughness induces local stress concentrations. Physical fatigue experiments are crucial to qualify materials for use but are limited in their capability to examine the mechanisms underlying the fatigue crack formation driving force due to these stress concentrations. Microstructure-sensitive computational models can aid in this regard and are employed in this work to examine the effects of surface roughness in Al 7075-T6. Digital microstructure models are subjected to crystal plasticity finite element method (CPFEM) simulations to examine the combined effects of microstructure and grain scale asperities on the driving force for fatigue crack formation. Following elastic–plastic shakedown, mesoscale volume-averaged fatigue indicator parameters (FIPs) are computed within fatigue damage process zones of grains. An increase in the intensity of realistic surface roughness profiles corresponds accordingly to larger FIPs but it is difficult to precisely interpret the mechanisms and effects of this intensification. We thus parametrically investigate surface asperities that couple with microstructure and lack of constraint on slip at the free surface to describe microstructure-sensitive surface roughness knockdown effects on fatigue resistance. The depth of a single valley (i.e., notch) due to surface roughness is found to be more detrimental to fatigue resistance than the radius (i.e., notch width, not to be confused with notch acuity). Finally, we also find that different crystallographic textures, grain morphologies, and number of sampled grains have a limited effect on the depth of influence of these notches.

36 MATERIALS SCIENCE↗

Effect of control surface mass unbalance on the stability of a closed-loop active control system

An inertial energy approach similar to the aerodynamic energy method for flutter suppression is used to investigate the effects of mass-unbalanced control surfaces on the stability of a closed-loop system. It is demonstrated that a spanwise section for sensor location can be obtained which ensures minimum sensitivity to the mode shapes of the aircraft. Leading-edge control is characterized by a compatibility between inertial stabilization and aerodynamic stabilization that trailing-edge control lacks.

Nissim, E.↗

Assessing the Effects of Various Surface Textures and Features on Turbulent Heat Transfer in Hypersonic Flight

Experiments were conducted in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (ballistic range) to quantify the effects on turbulent convective heat transfer of distributed surface roughness, and of isolated features, representative of thermal protection systems on atmospheric entry vehicles. The surface textures and features were applied on the conic frusta of 45o sphere-cone models having a nose-to-base radius ratio of 0.5, similar to the forebody geometry of the Galileo and Pioneer-Venus entry probes. Test conditions were selected to provide turbulent roughness Reynolds numbers, k+, in the ranges expected for outer planet entry missions. Turbulent flow on the conic frustum was achieved by tripping the flow on the sphere-segment nose cap with distributed surface roughness, created by sand-blasting the nose cap. Surface textures included distributed, acreage, roughness, as well as cavity and groove discrete features. The majority of the data to be presented are results for distributed roughness, which includes both random, sand-grain-like roughness, and regular pattern roughness. The pattern roughness was designed to represent the roughness on woven thermal protection system materials, such as NASA’s 3-D Medium Density Carbon Phenolic (3MDCP), also known as HEEET, developed by the Heatshield for Extreme Entry Environments Technology project. The pattern roughness tested is a 3-D wavy surface, and includes three different roughness element height-to-spacing ratios representative of two configurations of 3MDCP, and spanning ratios measured both before, and after, ablation in an arc jet test facility. The patterns tested in the ballistic range were laser-etched on metal models, and represented an idealized version of the real-world materials in which each roughness element was nearly identical. Additional tests were performed wherein the laser-etched patterns were degraded by sand-blasting with various sized grit media, to produce regular patterns with superimposed irregular roughness, more representative of flight materials. Results of each will be compared. The discrete features tested included cylindrical cavities and rectangular grooves of various width-to-depth ratios. Cavities represent either heatshield damage, such as from micro-meteoroid and orbital debris (MMOD) damage, or from designed penetrations, such as on the Genesis sample return capsule. The grooves were scaled representations of seams between segments of HEEET material in a notional tiled thermal protection system. The tests examined the effects on turbulent heating downstream of the isolated features. The tests were conducted at speeds between 3 km/s and 4 km/s in air between 0.15 atm and 0.25 atm (Mach numbers between 9 and 12). Roughness Reynolds numbers, k+, ranged from 12 to 70 for the sand roughness, and as high as 200 for the pattern roughness. Boundary-layer parameters required for calculating k+ were evaluated using computational fluid dynamics simulations using the DPLR (Data Parallel Line Relaxation) code. Each model included both rough- and smooth-wall segments, and heat transfer augmentation factors were determined as the ratio of the rough-wall to smooth-wall heat flux measured on each test.

hypersonic↗

The effect of monomolecular surface films on the microwave brightness temperature of the sea surface

It is pointed out that monomolecular surface films of biological origin are often encountered on the ocean surface, especially in coastal regions. The thicknesses of the monomolecular films are of the order of 3 x 10 to the -9th m. Huehnerfuss et al. (1978, 1981) have shown that monomolecular surface films damp surface waves quite strongly in the centimeter to decimeter wavelength regime. Other effects caused by films are related to the reduction of the gas exchange at the air-sea interface and the decrease of the wind stress. The present investigation is concerned with experiments which reveal an unexpectedly large response of the microwave brightness temperature to a monomolecular oleyl alcohol slick at 1.43 GHz. Brightness temperature is a function of the complex dielectric constant of thy upper layer of the ocean. During six overflights over an ocean area covered with an artificial monomolecular alcohol film, a large decrease of the brightness temperature at the L-band was measured, while at the S-band almost no decrease was observed.

Alpers, W.↗

Intercalation of Lithium in Pitch-Based Graphitized Carbon Fibers Chemically Modified by Fluorine: Soft Carbon With or Without an Oxide Surface

The effects of carbon structure and surface oxygen on the carbon's performance as the anode in lithium-ion battery were studied. Two carbon materials were used for the electrochemical tests: soft carbon made from defluorination of graphite fluoride, and the carbon precursor from which the graphite fluoride was made. In this research the precursor was graphitized carbon fiber P-100. It was first fluorinated to form CF(0.68), then defluorinated slowly at 350 to 450 C in bromoform, and finally heated in 1000 C nitrogen before exposed to room temperature air, producing disordered soft carbon having basic surface oxides. This process caused very little carbon loss. The electrochemical test involved cycles of lithium intercalation and deintercalation using C/saturated LiI-50/50 (vol %) EC and DMC/Li half cell. The cycling test had four major results. (1) The presence of a basic oxide surface may prevent solvent from entering the carbon structure and therefore prolong the carbon's cycle life for lithium intercalation-deintercalation. (2) The disordered soft carbon can store lithium through two different mechanisms. One of them is lithium intercalation. which gives the disordered carbon an electrochemical behavior similar to its more ordered graphitic precursor. The other is unknown in its chemistry, but is responsible for the high-N,oltage portion (less than 0.3V) of the charge-discharge curve. (3) Under certain conditions, the disordered carbon can store more lithium than its precursor. (4) These sample and its precursor can intercalate at 200 mA/g. and deintercalate at a rate of 2000 mA/g without significant capacity loss.

Hung, Ching-Chen↗

Electrostatic propulsion beam divergence effects on spacecraft surfaces, volume 2

The third phase of a program to develop understanding of and tolerance-level criteria for the deleterious effects of electrostatic rocket exhaust (Cs, Cs(+), Hg, Hg(+)) and materials of rocket construction impinging on typical classes of spacecraft (S/C) surfaces was completed. Models of ion engine effluents and models describing the degradation of S/C surfaces by these effluents are presented. Experimental data from previous phases are summarized and Phase 2 data and analysis are presented in detail. The spacecraft design implications of ion engine contaminants are discussed.

Hall, D. F.↗

Formation of a Stepped Si(100) Surface and Its Effect on the Growth of Ge Islands

The transition from a two-domain to one-domain surface on a Si(100) substrate is investigated. It is demonstrated using reflection high-energy electron diffraction that at a temperature of 600°C and a deposition rate of 0.652 Å/s onto a Si(100) substrate pre-heated to 1000°C and inclined at an angle of 0.35°C to the plane, a series of reflections from the 1 × 2 superstructure completely vanishes at a constant flow of Si. This is attributed to the transition of the surface from monoatomic to diatomic steps. At growth rates lower than 0.652 Å/s, the transition from a two-domain to one-domain surface is also observed; with a decrease in the growth rate, the intensity ratio I{sub 2×1}/I{sub 1×2} decreases and the maximum of the dependences shifts toward lower temperatures. The complete vanishing of the series of superstructural reflections after preliminary annealing at a temperature of 700°C is not observed; this series only vanishes after annealing at 900 and 1000°C. The growth of Ge islands on a Si(100) surface preliminary annealed at a temperature of 800°C is studied. It is shown that the islands tend to nucleate at the step edges. A mechanism of Ge island ordering on the Si(100) surface is proposed.

36 MATERIALS SCIENCE↗

Nuclear quantum effects of metal surface-mediated C–H activation

The nuclear quantum effects of surface-mediated C–H activation of surface CH 3 are considered for the pristine Pt(111) and Au(111) surfaces at 300 K. The kinetic barriers without nuclear quantum effects are calculated using both static density functional theory calculations and ab initio molecular dynamics. Static calculations are performed using the harmonic approximation while the free energy pathway is calculated using enhanced sampling molecular dynamics. Machine learning potentials are trained using generated datasets and validated against the ab initio molecular dynamics generated free energy pathways. The machine learning potentials are used to perform centroid molecular dynamics to consider the nuclear quantum effects of C–H activation. Nuclear quantum effects are found to have a very significant effect on the free energy pathway, with reduced importance at higher temperatures and in the CD 3 case.

Bunting, Rhys J. [Lawrence Livermore National Labo↗

The effect of temperature on the secondary electron emission yield from single crystal and polycrystalline diamond surfaces

The effect of temperature in the 293-473 K range, on the secondary electron emission (SEE) yield of single crystal and polycrystalline diamond film surfaces is reported. For the polycrystalline films the SEE yield was found to decay as function of electron irradiation dose while for the single crystal an increase occurs first, followed by a decrease. For both surfaces, the SEE yield increases significantly upon heating and obtained a nearly constant value with electron dose at 473 K. These effects are explained as due to the temperature dependence of the electron beam induced hydrogen desorption and surface band bending.

36 MATERIALS SCIENCE↗

Quantifying the effect of fracture surface topography on the scattering of grain boundary segregation measurement by Auger electron spectroscopy

The aim of this paper is to estimate the effect of the geometrical orientation of grain boundary facets on the quantification of grain boundary segregation by Auger electron spectroscopy (AES) on an in-situ fractured surface. Phosphorus grain boundary segregation (PGBS) was studied on 17 different samples (including 3 different steels and 12 different thermal treatments) using a MAC2 analyzer from Riber company. For each sample, 14 to 41 grain boundary facets were analyzed. It is demonstrated that there is proportionality between the PGBS mean value and the PGBS standard deviation obtained on one particular sample: for each sample, the PGBS standard deviation represents approximately 40% of the PGBS mean value. The topography of a typical purely intergranular fracture surface was determined by 3D stereographic observation in a SEM. The influence of surface topography on Auger quantification was then evaluated using the Auger quantification equations. The orientation of grain boundary facets with respect to the primary beam and the Auger analyzer was taken into account. The result is that, considering a homogeneous PGBS on all the grain boundary facets, a large scattering ({approx} 45%) of the PGBS quantification by AES can be accounted for by a purely geometrical effect (orientation of each facet with respect to the primary beam and to the Auger analyzer). This geometrical effect is nevertheless strongly dependant on the spectrometer geometry (respective position of primary beam, sample and Auger analyzer with respect to each other) and could be reduced by optimizing the relative positions of primary beam, sample and Auger analyzer. The topographical analysis was extended to the case of the well-known CMA (Cylindrical Mirror Analyzer). The scattering of the PGBS measurements with Auger spectrometers fitted with a CMA perpendicular to the fracture surface is expected to be much smaller.

36 MATERIALS SCIENCE↗

Comparing the cooling effectiveness of operationalisable urban surface combination scenarios for summer heat mitigation

Extreme summer heat in cities exacerbates the vulnerability of urban communities to heatwaves. Vegetative and reflective urban surfaces can help reduce urban heat. This study investigated the impacts of urban trees, green roofs and cool roofs on heat mitigation during average and extreme summer conditions in temperate oceanic Melbourne, Australia. We simulated the city climate using ‘The Air Pollution Model’ (TAPM) at a 1 km spatial resolution over 10 years, which according to our review of the literature, was the most prolonged period for simulation in Melbourne. During a widespread heatwave event, some of the tested scenarios with combined surface parameters could reduce the extreme values of the energy budget components- sensible heat, latent heat, and storage heat fluxes up to seasonal averages compared to the existing situation for Melbourne (control). The scenario with the highest (reasonable maximum) ground-level vegetation, green roofs, and cool roofs could reduce air temperatures up to 2.4 °C. The simulations suggest that a combined strategy with vegetative and high-albedo surfaces will deliver higher effectiveness with maximum cooling benefits and cost-effectiveness than individual strategies in cities. These results suggest the importance of collaborative strategic planning of urban surfaces to make cities healthier, sustainable, and liveable.

54 ENVIRONMENTAL SCIENCES↗

Surface Structure Dependence of SO 2 Interaction with Ceria Nanocrystals with Well-defined Surface Facets

The effects of the surface structure of ceria (CeO 2 ) on the nature, strength, and amount of species resulting from SO 2 adsorption were studied using in situ IR and Raman spectroscopies coupled with mass spectrometry, along with first-principles calculations based on density functional theory (DFT). CeO 2 nanocrystals with different morphologies, namely, rods (representing a defective structure), cubes (100 facet), and octahedra (111 facet), were used to represent different CeO 2 surface structures. IR and Raman spectroscopic studies showed that the structure and binding strength of adsorbed species from SO 2 depend on the shape of the CeO 2 nanocrystals. SO 2 adsorbs mainly as surface sulfites and sulfates at room temperature on CeO 2 rods, cubes, and octahedra that were either oxidatively or reductively pretreated. The formation of sulfites is more evident on CeO 2 octahedra, whereas surface sulfates are more prominent on CeO 2 rods and cubes. This is explained by the increasing reducibility of the surface oxygen in the order octahedra < cubes < rods. Bulk sulfites are also formed during SO 2 adsorption on reduced CeO 2 rods. The formation of surface sulfites and sulfates on CeO 2 cubes is in good agreement with our DFT results of SO 2 interactions with the CeO 2 (100) surface. CeO 2 rods desorb SO2 at higher temperatures than cubes and octahedra nanocrystals, but bulk sulfates are formed on CeO 2 rods and cubes after high-temperature desorption whereas only some surface sulfates/sulfites are left on octahedra. This difference is rationalized by the fact that CeO 2 rods have the highest surface basicity and largest amount of defects among the three nanocrystals, so they bind and react with SO 2 strongly and are the most degraded after SO 2 adsorption cycles. The fundamental understanding obtained in this work on the effects of the surface structure and defects on the interaction of SO 2 with CeO 2 provides insights for the design of more sulfur-resistant CeO 2 -based catalysts.

36 MATERIALS SCIENCE↗

Effects of Mineral Surface Properties on Supercritical CO 2 Wettability in a Siliciclastic Reservoir

Wettability is a key reservoir characteristic influencing geological carbon sequestration (GCS) processes, such as CO 2 transport and storage capacity. Wettability is often determined on a limited number of reservoir samples by measuring the contact angle at the CO 2 /brine/mineral interface, but the ability to predict this value remains a challenge. In this work, minerals comprising a natural reservoir sample were identified, and the influence of their surface roughness and mineralogy on the contact angle was quantified to evaluate predictive models and controlling mechanisms. The natural sample was obtained from the Mount Simon formation, a representative siliciclastic reservoir that is the site of a United States Department of Energy CO 2 injection project. A thin section of the Mount Simon sandstone was examined with compound light microscopy and environmental scanning electron microscopy (ESEM) coupled with energy-dispersive X-ray spectroscopy (EDS). Quartz and feldspar were identified as dominant minerals and were coated with various reddish black precipitates consistent with illite clay and iron oxide hematite. Contact angle (θ) measurements were conducted for the four representative minerals and the Mount Simon sample over a range of pressures (2–25 MPa) at 40 °C. At supercritical conditions, all samples are strongly water-wet, with contact angles between 27° and 45°. Several predictive models for contact angle were evaluated for the mineral and Mount Simon samples, including the Wenzel and Cassie–Baxter models, plus newly proposed modifications of these that account for the fraction of different minerals comprising the reservoir sample surface, the surface roughness, and the extent that roughness pits are filled with brine. Modeling results suggest that the fraction of mineral surfaces containing roughness pits filled with brine is the most important reservoir characteristic that controls wettability in the Mount Simon sandstone, followed by surface mineralogy. Finally, to our knowledge, this is one of the few studies to investigate the effects of individual minerals on the wettability of a natural reservoir sample.

58 GEOSCIENCES↗