SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Program is revised of NASA/Lockheed program to numerically analyze complex viscous flow about slotted airfoils. Airfoil to be analyzed can contain as many as 10 components with negative or positive overlap. Program is written in FORTRAN IV and Assembled for batch execution on CYBER 175 only.
Lightweight connector automatically aligns beams to be jointed, and withstands torsion, tension, and compression loads. One beam has connector, other has receptor. Bracket aligns connector and receptor. When actuated, spring in connector pushes shaft into receptor. Hooks on shaft snap to lock into receptor slots. Union can be separated easily without damage. Connectors are designed for in-space assembly, but may be suited to ground assemblies as well.
Snap ring with slotted tabs fits groove in shaft. Sleeve to be held on shaft fits over snap ring keeping it from expanding. Tabs are bent out to keep sleeve from slipping off shaft.
Flange adjusts center of rotation of gimble-mounted objects such as telescopes. Three aluminum plates are machined to have interlocking orthogonal keys and ways. Outer plate is mounted to shaft. Inner plate is attached to object. Middle and inner plate slide along on axis. Screws slide in slots parallel to ways for adjustment, then tighten to lock position along each axis. Device is similar to crossed ways found on industrial machine tools, but simpler, lighter, and much smaller.
Flush-mountable assembly composed of disk radiator sandwiched between planes of metal-clad dielectric board has greater bandwidths and beamwidths than simple disk antenna. Conducting planes connect so that disk is enclosed in cavity with Y-shaped slot in top plane. Cavity is excited by microwave energy from disk and radiates from trislot aperature.
A small scale rectangular throat ejector with plane slot nozzles and a fixed throat area was tested to determine the effects of diffuser sidewall length, diffuser area ratio, and sidewall nozzle position on thrust and mass augmentation. The thrust augmentation ratio varied from approximately 0.9 to 1.1. Although the ejector did not have good thrust augmentation performance, the effects of the parameters studied are believed to indicate probable trends in thrust augmenting ejectors.
The beneficial aspects of an ejector powered V/STOL concept were reviewed. The feasibility of satisfactorily incorporating an ejector system in a high performance V/STOL aircraft was investigated. The external augmentor concept, based on the use of chordwise ejector slots, is presented. It is concluded that the external augmentor concept has a basic inherent simplicity and a sufficient augmentor performance potential to make feasible a high performance V/STOL aircraft based on ejectors.
The low-speed longitudinal and lateral-directional characteristics of a scale model of an advanced arrow-wing supersonic cruise configuration were investigated in tests conducted at a Reynolds number of 4.19 x 10 to the 6th power based on the mean aerodynamic chord, with an angle of attack range from - 6 deg to 23 deg and sideslip angle range from -15 deg to 20 deg. The effects of segmented leading-edge flaps, slotted trailing-edge flaps, horizontal and vertical tails, and ailerons and spoilers were determined. Extensive pressure data and flow visualization pictures with non-intrusive fluorescent mini-tufts were obtained.
Neutrally bouyant helium-filled bubbles were observed as they followed the streamlines in a horseshoe vortex system around the vane leading edge in a large scale, two dimensional, turbine stator cascade. Inlet Reynolds number, based on true chord, ranged between 100,000 to 300,000. Bubbles were introduced into the endwall boundary layer through a slot upstream of the vane leading edge. The paths of the bubbles were recorded photographically as streaklines on 16 mm movie film. Individual frames from the film were selected, and overlayed to show the details of the horseshoe vortex around the leading edge. The transport of the vortex across the passage near the leading edge is clearly seen when compared to the streaks formed by bubbles carried in the main stream. Limiting streamlines on the endwall surface were traced by the flow of oil drops.
An injector for 3000 psia chamber pressure using liquid oxygen and gaseous methane propellants is presented. The injector is intended to be evaluated during a series of pressure-fed test firings using a water-cooled calorimeter chamber and a milled-slot regenerative chamber. Combustion efficiency, combustion stability, ignition and injector face heat transfer assessments were made for candidate injector body and pattern design approaches. This evaluation resulted in baselining an oxidizer post type manifold with a 60 element platelet coaxial swirler injector pattern. An axial acoustic resonator cavity was created at the injector/chamber interface.
On the basis of static aero/acoustic data obtained at model scale, the effect of exhaust nozzle size on flyover noise is evaluated at full scale for different STOL-OTW nozzle configurations. Three types of nozzles are evaluated: a circular/deflector nozzle mounted above the wing; a slot/deflector nozzle mounted on the wing; and a slot nozzle mounted on the wing. The nozzle exhaust plane location, measured from the wing leading edge, was varied from 10 to 46 percent of the wing chord (flaps retracted). Flap angles of 20 deg (takeoff) and 60 deg (approach) are included in the study. Initially, perceived noise levels (PNL) are calculated as a function flyover distance at 152m altitude. From these plots, static EPNL values (defined as flyover relative noise levels), are obtained as functions of nozzle size for equal aerodynamic performance (lift and thrust). The acoustic benefits attributable to nozzle size relative to a given wing chord size are assessed.
The mullite-molten silicon interaction was evaluated through fabrication of a series of bodies made with variations in density, alumina-silica ratio, and glass-crystalline ratio. The materials were tested in a sessile drop technique. None of the variations stood up to extended exposure to molten silicon sufficiently to be recommended as a container material. However, directional solidification experiments suggest that, under proper conditions, contamination of the silicon by mullite containers can be minimized. To improve an already good thermal expansion match between mullite and silicon, compositional variations were studied. Altering of the alumina-silica ratio was determined to give a continuously varying thermal expansion. A standard mullite composition was selected and substrates 40 x 4 x .040 inches were fabricated. Slotted substrates of various configurations and various compositions were also fabricated.
Analytical and computational techniques were developed to predict the stability behavior of liquid propellant rocket combustors using damping devices such as acoustic liners, slot absorbers, and injector face baffles. Models were developed to determine the frequency and decay rate of combustor oscillations, the spatial and temporal pressure waveforms, and the stability limits in terms of combustion response model parameters.
The design of an L-band high resolution soil moisture radiometer is described. The selected system is a planar slotted waveguide array at L-band frequencies. The square aperture is 74.75 m by 74.75 m subdivided into 8 tilted subarrays. The system has a 290 km circular orbit and provides a spatial resolution of 1 km. The aperture forms 230 simultaneous beams in a cross-track pattern which covers a swath 420 km wide. A revisit time of 6 days is provided for an orbit inclination of 50 deg. The 1 km resolution cell allows an integration time of 1/7 second and sharing this time period sequentially between two orthogonal polarization modes can provide a temperature resolution of 0.7 K.
A tail mounted spin recovery parachute system was designed and developed by the NASA Langley Research Center for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low wing, single engine, and twin-engine design. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring slot spin recovery parachute. The total system weighs 8.2 kg (18 lb). System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute was used successfully in flight 17 times.
The optimum design of nacelles that operate over a wide range of aerodynamic conditions and their inlets is described. For low speed operation the optimum internal surface velocity distributions and skin friction distributions are described for three categories of inlets: those with BLC, and those with blow in door slots and retractable slats. At cruise speed the effect of factors that reduce the nacelle external surface area and the local skin friction is illustrated. These factors are cruise Mach number, inlet throat size, fan-face Mach number, and nacelle contour. The interrelation of these cruise speed factors with the design requirements for good low speed performance is discussed.
A tail mounted spin recovery parachute system was designed and developed for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low wing, high wing, single engine and twin engine designs. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring slot spin recovery parachute. The total system weighs 8.2 kg. System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute was used successfully in flight 17 times.
The invention and design of an aerodynamic high lift device which provided a solution to an aircraft performance problem are described. The performance problem of converting a high speed cruise airfoil into a low speed aerodynamic shape that would provide landing and take-off characteristics superior to those available with contemporary high lift devices are addressed. The need for an improved wing leading edge device that would complement the high lift performance of a triple slotted trailing edge flap is examined. The mechanical and structural aspects of the variable camber flap are discussed and the aerodynamic performance aspects only as they relate to the invention and design of the device are presented.