Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reentry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Description of recent changes in the Langley 6- by 28-inch transonic tunnel

Calibrations were obtained in the Langley 6 by 28-inch transonic tunnel with newly installed controllable reentry flaps and test section floor and ceiling. Using available theory, the top and bottom slotted walls were redesigned for minimum wind tunnel interference errors of blockage and stream-line curvature. To minimize Mach number gradients along the tunnel axis downstream of the model, controllable flaps were installed to regulate the flow reentering the test section through the slotted walls. The flap setting is independent of stagnation pressure and varies only with Mach number. The freestream Mach number is determined from the pressrue measured at a station 66.04 cm upstream of the model station. The model has no significant influence on the vertical Mach number distribution at this station. This method of Mach number determination appears to be more accurate than one using the plenum pressure.

Sewall, W. G.↗

Infrared Imagery of Shuttle (IRIS). Task 1

Assessment of available IR sensor technology showed that the four aerothermodynamic conditions of interest during the entry trajectory of space shuttle can be accommodated by an aircraft flying parallel to the orbiter reentry ground track. Thermal information from the sides of the vehicle can be obtained with degraded performance (temperatures below 800 K) by flying the C-141 aircraft on the opposite side of the shuttle ground track and in the direction opposite that which is optimum for lower surface viewing. An acquisition system using a 6.25-cm aperture telescope and a single indium antimonide detector were designed to meet the acquisition requirements and interface with the 91.5-cm telescope with minimum modification. An image plane system using 600 indium antimonide detectors in two arrays which requires no modification to the existing telescope was also designed. Currently available components were used in a data handling system with interfaces with the experimentors station and the HP2100 computer.

Chocol, C. J.↗

Preliminary analysis of STS-1 entry flight data

A preliminary analysis of data acquired during the first shuttle orbiter reentry is presented. Heating levels were higher than predicted. Variations in measured versus predicted lift to drag ratio and trim are discussed, as are plots showing time histories of control surface and jet activity. The confidence felt in the stability and control derivatives is only fair. Confidence in the derivatives extracted for Mach numbers below 3.5 is especially weak, because these derivatives were affected by sideslip data contaminated by wind and turbulence, nonindependent rudder motions, and buffet. The sources of the data used are described. Recommendations are presented for changes to the Aerodynamic Data Book, and for planning future flights.

Source record↗

Hypersonic and planetary entry flight mechanics

The book treats hypersonic flight trajectories and atmospheric entry flight mechanics in light of their importance for space shuttle entry. Following a review of the structures of planetary atmospheres and aerodynamic forces, equations are derived for flight over a spherical planet, and the performance of long-range hypervelocity vehicles in extra-atmospheric flight is analyzed. Consideration is then given to vehicle trajectories in the powered and atmospheric reentry phases of flight, and several first-order solutions are derived for various planetary entry situations. The second-order theory of Loh for entry trajectories is presented along with the classical theories of Yaroshevskii and Chapman for entry into planetary atmospheres, and the thermal problems encountered in hypersonic flight are analyzed. A unified theory for entry into planetary atmospheres is then introduced which allows the performance of a general type of lifting vehicle to be studied, and applied to the analysis of orbit contraction due to atmospheric drag, flight with lift modulation and lateral maneuvers.

Vinh, N. X.↗

The Shuttle and its importance to space medicine

The physiological effects of space flights on humans are reviewed, and the opportunities offered by frequent and repetitive Space Shuttle flights for space medical research are discussed. The most significant changes encountered in the vestibular, cardiopulmonary, musculoskeletal and hematopoietic systems during and after past space missions are indicated, and the time courses of the physiological shifts associated with space acclimatization and readaptation to a 1-g environment are summarized. Effects directly attributable to the absence of gravity, including postural changes and fluid shifts, are considered, and additional contributing factors to physiological changes imposed by the spacecraft operational environment are pointed out. Differences between the Space Shuttle missions and all previous missions in the areas of reentry profiles and varied crew composition are discussed, and results of experiments on the relative acceleration tolerances of men and women of different ages and the usefulness of the anti-g suit are presented. Directions for future research in space medicine available with the Shuttle are examined, with particular emphasis on the neurovestibular system cardiopulmonary dynamics, calcium metabolism, the erythropoietic system and the effects of space radiation.

Nicogossian, A.↗

An empirical method for computing leeside centerline heating on the Space Shuttle Orbiter

An empirical method is presented for computing top centerline heating on the Space Shuttle Orbiter at simulated reentry conditions. It is shown that the Shuttle's top centerline can be thought of as being under the influence of a swept cylinder flow field. The effective geometry of the flow field, as well as top centerline heating, are directly related to oil-flow patterns on the upper surface of the fuselage. An empirical turbulent swept cylinder heating method was developed based on these considerations. The method takes into account the effects of the vortex-dominated leeside flow field without actually having to compute the detailed properties of such a complex flow. The heating method closely predicts experimental heat-transfer values on the top centerline of a Shuttle model at Mach numbers of 6 and 10 over a wide range in Reynolds number and angle of attack.

Helms, V. T., III↗

Annual survey of spaceflight safety systems: 11th supplement. Survey period - July 1980-June 1981

Reports in the field of space flight safety applicable to current and future operational space activities which appeared between July 1980 and June 1981 are surveyed. Subjects in the area of flight rescue and safety during launch, on-orbit, reentry and landing phases include the major activities and findings of the first Shuttle test flight, a slidewire system for emergency egress from the Space Shuttle on the launch pad, and the testing of the Spacelab engineering model. In the area of human capabilities and crew roles, attention is given to reports of repairs to the Salyut 6 space station made by a Soyuz crew, and an assessment of weightlessness effects on space worker health and safety. Safety requirements for STS payloads including pressure vessels, and the Orbiter window system and for spacecraft testing are also presented, along with those for a television system to aid in monitoring astronaut extravehicular activities. For the operation of large space structures, reports include EVA equipment for satellite servicing and the safety aspects of connectors used in construction. Finally, attention is given to safety-related criteria in a study of Shuttle interactions with the proposed Space Operations Center.

Brown, N. E.↗

Thermomechanical processing of Haynes alloy No. 188 sheet to improve creep strength

A study has been carried out with the objective of improving the low-strain creep strength of thin gauge (0.38 mm) sheet of Haynes alloy No. 188, a candidate material for the heat shields of advanced reentry and hypersonic vehicles. It is found that significant improvements in the low-strain creep strength are obtained in sheets with a strong recrystallized texture produced by a thermomechanical treatment. The optimum results are achieved after 80% final coldwork followed by a 10-min anneal at 1505 K.

Klarstrom, D. L.↗

Bridging Gaps Between Refractory Tiles

Excessively large gaps between tiles on Space Shuttle eliminated without time-consuming and costly procedure of removing and replacing tiles. Ceramic tile silver is bonded in gap. Bonded silver prevents airframe under gap from getting too hot during reentry and presents aerodynamically smooth exterior surface.

Haney, J. W. J.↗

Report on research and technology-FY 1981

More than 65 technical reports, papers, and articles published by personnel and contractors at the Dryden Flight Research Center are listed. Activities performed for the Offices of Aeronautics and Space Technology, Space and Terrestrial Applications, Space Transportation Systems, and Space Tracking and Data Systems are summarized. Preliminary stability and control derivatives were determined for the shuttle orbiter at hypersonic speeds from the data obtained at reentry. The shuttle tile tests, spin research vehicle nose shapes flight investigations, envelope expansion flights for the Ames tilt rotor research aircraft, and the AD-1 oblique wing programs were completed as well as the KC-135 winglet program.

Source record↗

Columbia carries astronomy experiments on third test flight

The Space Transportation System 3 flight is discussed. The objectives of the test flight are given as well as an account of launch preparations, in liftoff, reentry; and landing. Numerous astronomy and space science experiments carried in the cargo bay are described.

Source record↗

Langley Atmospheric Information Retrieval System (LAIRS): System description and user's guide

This document presents the user's guide, system description, and mathematical specifications for the Langley Atmospheric Information Retrieval System (LAIRS). It also includes a description of an optimal procedure for operational use of LAIRS. The primary objective of the LAIRS Program is to make it possible to obtain accurate estimates of atmospheric pressure, density, temperature, and winds along Shuttle reentry trajectories for use in postflight data reduction.

Boland, D. E., Jr.↗

A spectroscopic experimental and computer-assisted empirical model for the production and energetics of excited oxygen molecules formed by atom recombination on shuttle tile surfaces

A visible emission spectroscopic method was developed. The amounts of excited singlet and triplet oxygen molecules produced by recombination on the Space Shuttle Orbiter thermal protective tiles at elevated temperatures are determined. Rate constants and energetics of the extremely exothermic reaction are evaluated in terms of a chemical and mathematical model. Implications for potential contribution to Shuttle surface reentry heating fluxes are outlined.

Owan, D. A.↗

Advanced turbine study

Experiments to determine the available increase in turbine horsepower achieved by increasing turbine inlet temperature over a range of 1800 to 2600 R, while applying current gas turbine airfoil cling technology are discussed. Four cases of rocket turbine operating conditions were investigated. Two of the cases used O2/H2 propellant, one with a fuel flowrate of 160 pps, the other 80 pps. Two cases used O2/CH4 propellant, each having different fuel flowrates, pressure ratios, and inlet pressures. Film cooling was found to be the required scheme for these rocket turbine applications because of the high heat flux environments. Conventional convective or impingement cooling, used in jet engines, is inadequate in a rocket turbine environment because of the resulting high temperature gradients in the airfoil wall, causing high strains and low cyclic life. The hydrogen-rich turbine environment experienced a loss, or no gain, in delivered horsepower as turbine inlet temperature was increased at constant airfoil life. The effects of film cooling with regard to reduced flow available for turbine work, dilution of mainstream gas temperature and cooling reentry losses, offset the relatively low specific work capability of hydrogen when increasing turbine inlet temperature over the 1800 to 2600 R range. However, the methane-rich environment experienced an increase in delivered horsepower as turbine inlet temperature was increased at constant airfoil life. The results of a materials survey and heat transfer and durability analysis are discussed.

Source record↗

Computational Aspects of Heat Transfer in Structures

Techniques for the computation of heat transfer and associated phenomena in complex structures are examined with an emphasis on reentry flight vehicle structures. Analysis methods, computer programs, thermal analysis of large space structures and high speed vehicles, and the impact of computer systems are addressed.

Adelman, H. M.↗

Adjustable high emittance gap filler

A flexible, adjustable refractory filler is disclosed for filling gaps between ceramic tiles forming the heat shield of a space shuttle vehicle, to protect its aluminum skin during atmospheric reentry. The easily installed and replaced filler consists essentially of a strip of ceramic cloth coated, at least along both its longitudinal edges with a room temperature vulcanizable silicone rubber compound with a high emittance colored pigment. The filler may have one or more layers as the gap width requires. Preferred materials are basket weave aluminoborosilicate cloth, and a rubber compounded with silicon tetraboride as the emittance agent and finely divided borosilicate glass containing about 7.5% B2O3 as high temperature binder. The filler cloth strip or tape is cut to proper width and length, inserted into the gap, and fastened with previously applied drops of silicone rubber adhesive.

Leiser, D. B.↗

High temperature penetrator assembly with bayonet plug and ramp-activated lock

A penetration apparatus, for very high temperature applications in which a base plug is inserted into an opening through a bulkhead is described. The base plug has a head shape and is seated against the highest temperature surface of the bulkhead, which may be the skin of the nose cone or other part of a space vehicle intended for nondestructive atmospheric reentry. From the second side of the bulkhead at which the less severe environment is extant, a bayonet plug is inserted into the base plug and engages an internal shoulder at about 90 deg rotation. The bayonet plug has an integral flanged portion and a pair of ramping washers which are located between the flange and the second bulkhead surface with a spacing washer as necessary.

Wood, K. E.↗

Preliminary risk assessment for nuclear waste disposal in space, volume 2

Safety guidelines are presented. Waste form, waste processing and payload fabrication facilities, shipping casks and ground transport vehicles, payload primary container/core, radiation shield, reentry systems, launch site facilities, uprooted space shuttle launch vehicle, Earth packing orbits, orbit transfer systems, and space destination are discussed. Disposed concepts and risks are then discussed.

Rice, E. E.↗