SEARCH · Engineering Papers

Results for “polymer additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

All sources NASA NTRS DOE OSTI

NASA NTRS1999

Flight Validation of Atomic Oxygen Resistant Resistant Polymers

Because of its high reactivity, atomic oxygen causes surface erosion on polymeric materials. although the reaction efficiency depends on the chemical structure of the polymer. We have found an organotin compound, bis(triphenyltin) oxide (BTO), which has an unusually high solubility in solutions of a number of commercial high performance polymers. Films of these polymers containing BTO showed a substantial reduction in erosion by atomic oxygen when compared with films of the pure material. Analysis has shown that in the presence of atomic oxygen, erosion of the exposed surfaces of the BTO-containing films leaves a residual protective tin oxide coating . Since the additive is uniformly distributed throughout the polymeric material, any break or puncture in the protective coating is "healed" by the material below. Samples were exposed to the environment of the low earth orbit (LEO) on two Space Shuttle flights, STS-46, in June of 1992, and STS-51 in September of 1993. The analysis of these samples has been reported previously. For both flights, the samples were small (1.3 cm and 1.9 cm respectively) thus limiting the scope of analysis. In the research under this cooperative agreement, films of a polyetherimide, were exposed to the LEO environment on Space Shuttle flight STS-85 in August of 1997 as part of the Evaluation of Space Environment and Effects on Materials (ESEM) experiment. The polyetherimide chosen is available commercially as Ultem, registered to the General Electric Company. Films of pure Ultem, Ultem with 10% BTO by mass, and Ultem with 20% BTO by mass were exposed in the ram direction for 40 hours during STS-85. Ultem has a Tg of 215 deg C and is soluble in common chlorinated solvents. Granules of the polymer were dried at 120 deg C, but otherwise were used as received. Films were cast on a glass plate from a solution of the polymer in a 60/40 (w/w) mixture of chloroform and 1,1,2,2-tetrachloroethane. The plate was placed in a dust-free box for at least 24 hours to allow much of the solvent to evaporate, and then was moved to a vacuum oven and slowly heated from 20 to 220 deg C over a period of two weeks to completely remove all solvent. Each exposed sample was 7.6 cm long and 2.2 cm wide and about 0.025 mm thick. The structures of Ultem and bis(triphenyltin) oxide are shown.

Kiefer, Richard L.↗

DOE OSTI2026

A Vibrational Probe of Electrical Doping in N2200 and Fermi-Level Alignment at Polymer Cathode/Metal Cocatalyst/Electrolyte Junctions

Hybrid (photo)cathodes consisting of conjugated polymer and hydrogen evolution reaction (HER) cocatalysts are an emerging platform for low-cost solar fuel generation. Poly{[N,N′-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5′-(2,2′-bithiophene)}, known as P(NDI2OD-T2) or N2200, is a promising electron accepting material for bulk heterojunction photocathodes. Unlike inorganic (photo)electrodes, much less is known about the energetic alignment of conjugated polymer electrode/metal/electrolyte junctions. Here, in this work, we investigate the electrical doping behavior in an N2200 cathode and its Fermi-level alignment with gold nanoparticles, which is used here as a model for the hydrogen evolution metal cocatalyst. Through UV/visible, Raman, and attenuated total-reflectance infrared spectroelectrochemistry, we observe the impact of electrical doping on the vibrational frequencies of neutral, anion, and dianion species in N2200, which suggests that electron density changes within the corresponding naphthalene-diimide (NDI) units. Upon one-electron reduction, the $C=O$ stretching frequency of the NDI anion unit (polaron) shows a red shift by ∼ 68 cm –1 . Additionally, the $C=O$ stretching frequency of neutral units in the doped N2200 shows a minor red shift of ∼ 5 cm –1 , suggesting charge transfer from neighboring polaron units. Surface-enhanced Raman spectroscopy measurements of a gold nanoparticle-functionalized N2200 electrode revealed that the Au Fermi level only shifts with that of N2200 upon polaron formation; thus, the formal potential of polymer polaron formation determines the behavior of the catalyst Fermi level, which we posit will modulate reaction capability. This mechanistic study provides a new approach for understanding the nanometer-scale energetics at the conjugated polymer/cocatalyst junction and provides critical insights for the future design of HER (photo)cathodes.

charge transfer↗

DOE OSTI2024

Natural diversity screening, assay development, and characterization of nylon-6 enzymatic depolymerization

Successes in biocatalytic polyester recycling have raised the possibility of deconstructing alternative polymers enzymatically, with polyamide (PA) being a logical target due to the array of amide-cleaving enzymes present in nature. Here, we screen 40 potential natural and engineered nylon-hydrolyzing enzymes (nylonases), using mass spectrometry to quantify eight compounds resulting from enzymatic nylon-6 (PA6) hydrolysis. Comparative time-course reactions incubated at 40-70 °C showcase enzyme-dependent variations in product distributions and extent of PA6 film depolymerization, with significant nylon deconstruction activity appearing rare. The most active nylonase, a NylC K variant we rationally thermostabilized (an N-terminal nucleophile (Ntn) hydrolase, NylC K -TS, T m = 87.4 °C, 16.4 °C higher than the wild-type), hydrolyzes 0.67 wt% of a PA6 film. Reactions fail to restart after fresh enzyme addition, indicating that substrate-based limitations, such as restricted enzyme access to hydrolysable bonds, prohibit more extensive deconstruction. Overall, this study expands our understanding of nylonase activity distribution, indicates that Ntn hydrolases may have the greatest potential for further development, and identifies key targets for progressing PA6 enzymatic depolymerization, including improving enzyme activity, product selectivity, and enhancing polymer accessibility.

09 BIOMASS FUELS↗

DOE OSTI2020

An epoxy-reinforced ceramic sheet as a durable solid electrolyte for solid state Na-ion batteries

In a conventional Na-ion battery system using liquid electrolyte, there are critical safety issues due to the instability of the liquid electrolyte. Na 3 Zr 2 Si 2 PO 12 (NASICON) solid electrolyte is a material that is sufficient to replace a liquid electrolyte as it has high ionic conductivity and thermal and electrochemical stability. However, as there is a large interfacial resistance in the NASICON solid electrolyte powder, even when used in combination with a polymer electrolyte, the advantageous effects of ceramics are not easily exhibited. In this study, we propose a top-down method of combining a polymer with a ceramic in which an ion transport channel is previously formed. In this method, a NASICON solid electrolyte is partially sintered to form ion transport channels. Then the NASICON solid electrolyte pores are filled with an epoxy polymer to increase the strength of the epoxy-NASICON composite electrolyte. This method demonstrates the possibility of our composite electrolyte being used as a thin and strong film. As a result of our methods, the ionic conductivity and thermal and electrochemical stability of NASICON were maintained, while the physical strength was enhanced by approximately 2 times. In addition, a capacity of 120 mA h g -1 and stability of 20 cycles were confirmed in a half cell with a Na 3 V 2 (PO 4 ) 3 cathode and Na metal. This method proposes a new direction for research regarding composite electrolytes created using an oxide-based solid electrolyte.

25 ENERGY STORAGE↗

NASA NTRS2002

Predictions for Radiation Shielding Materials

Radiation from galactic cosmic rays (GCR) and solar particle events (SPE) is a serious hazard to humans and electronic instruments during space travel, particularly on prolonged missions outside the Earth s magnetic fields. Galactic cosmic radiation (GCR) is composed of approx. 98% nucleons and approx. 2% electrons and positrons. Although cosmic ray heavy ions are 1-2% of the fluence, these energetic heavy nuclei (HZE) contribute 50% of the long-term dose. These unusually high specific ionizations pose a significant health hazard acting as carcinogens and also causing microelectronics damage inside spacecraft and high-flying aircraft. These HZE ions are of concern for radiation protection and radiation shielding technology, because gross rearrangements and mutations and deletions in DNA are expected. Calculations have shown that HZE particles have a strong preference for interaction with light nuclei. The best shield for this radiation would be liquid hydrogen, which is totally impractical. For this reason, hydrogen-containing polymers make the most effective practical shields. Shielding is required during missions in Earth orbit and possibly for frequent flying at high altitude because of the broad GCR spectrum and during a passage into deep space and LunarMars habitation because of the protracted exposure encountered on a long space mission. An additional hazard comes from solar particle events (SPEs) which are mostly energetic protons that can produce heavy ion secondaries as well as neutrons in materials. These events occur at unpredictable times and can deliver a potentially lethal dose within several hours to an unshielded human. Radiation protection for humans requires safety in short-term missions and maintaining career exposure limits within acceptable levels on future long-term exploration missions. The selection of shield materials can alter the protection of humans by an order of magnitude. If improperly selected, shielding materials can actually increase radiation damage due to penetration properties and nuclear fragmentation. Protecting space-borne microelectronics from single event upsets (SEUs) by transmitted radiation will benefit system reliability and system design cost by using optimal shield materials. Long-term missions on the surface of the Moon or Mars will require the construction of habitats to protect humans during their stay. One approach to the construction is to make structural materials from lunar or Martian regolith using a polymeric material as a binder. The hydrogen-containing polymers are considerably more effective for radiation protection than the regolith, but the combination minimizes the amount of polymer to be transported. We have made composites of simulated lunar regolith with two different polymers, LaRC-SI, a high-performance polyimide thermoset, and polyethylene, a thermoplastic.

Kiefer, Richard L.↗

DOE OSTI2025

Sulfur Conversion to Donor‐Acceptor Ladder Polymer Networks through Mechanochemical Nucleophilic Aromatic Substitution for Efficient CO 2 Photoreduction

The development of synthetic methods capable of converting elemental sulfur into conjugated porous sulfur‐rich polymers remains a great challenge, although direct utilization of this readily available feedstock can significantly enrich its uses and circumvent environmental problems during sulfur storage. Here, we report herein mechanochemical (MC) nucleophilic aromatic substitution (S N Ar) that enables sulfur conversion into thianthrene‐bridged porous ladder polymer networks with dense donor‐acceptor (D−A) molecular junctions. We demonstrate that the key lies in the generation of bent thianthrene units through a solid‐state ball‐milling condensation reaction between 1,2‐dihaloarenes and elemental sulfur. We also show that the assembling of D−A structural motifs into porous networks affords efficient visible‐light‐driven photocatalytic reduction of carbon dioxide (CO 2 ) with water (H 2 O) vapor, in the absence of any additional photosensitizer, sacrificial agents or cocatalysts. Exceptional photoinduced charge separation along with boosted exciton dissociation results in a high‐performance of carbon monoxide (CO) production rate of 306.1 μmol g −1 h −1 with near 100 % CO selectivity, which is accompanied by H 2 O oxidation to O 2 , as confirmed by both experimental and theoretical results. We anticipate this novel MC S N Ar approach will advance processing techniques for direct sulfur utilization and facilitate new possibilities for the synthesis of D−A ladder polymer networks with promising potential in photocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Photoinitiator Selection and Concentration in Photopolymer Formulations towards Large-Format Additive Manufacturing

Photopolymers are an attractive option for large-format additive manufacturing (LFAM), because they can be formulated from structural thermosets and cure rapidly in ambient conditions under low-energy ultraviolet light-emitting diode (UV LED) lamps. Photopolymer cure is strongly influenced by the depth penetration of UV light, which can be limited in the 2–4 mm layer thicknesses typical of LFAM. Photoinitiator (PI) systems that exhibit photobleaching have proven useful in thick-section cure applications, because they generate a photoinitiation wavefront, but this effect is time-dependent. This study investigates the light transmission and through-thickness cure behavior in (meth)acrylate photopolymer formulations with the photobleaching initiator bis(2,4,6-trimethylbenzoyl)-phenylphosphine oxide (BAPO). Utilizing an optical model developed by Kenning et al., lower concentrations (0.1 wt% to 0.5 wt%) of BAPO were predicted to yield rapid onset of photoinitiation. In situ cure measurements under continuous UV LED irradiation of 380 mW/cm2 showed that a 0.1 wt% concentration of BAPO achieved peak polymerization rate within 2.5 s at a 3-mm depth. With only 1 s of irradiation at 1.7 W/cm2 intensity, the 0.1 wt% BAPO formulation also achieved the highest level of cure of the formulas tested. For an irradiation dose of 5.5 J/cm2 at a duration of 3.7 s, cured polymer specimens achieved a flexural strength of 108 MPa and a flexural modulus of 3.1 GPa. This study demonstrates the utility of optical modeling as a potential screening tool for new photopolymer formulations, primarily in identifying an upper limit to PI concentration for the desired cure depth. The results also show that photobleaching provides only a limited benefit for LFAM applications with short (1.0 s to 3.7 s) UV irradiation times and indicate that excess PI concentration can inhibit light transmission even under extended irradiation times up to 60 s.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Isomer-Tailored Carbon Molecular Sieve Membranes with High Gas Separation Performance

Not provided.

Chemistry↗

DOE OSTI2024

Non-close-packed plasmonic Bravais lattices through a fluid interface-assisted colloidal assembly and transfer process

Abstract The assembly of colloids at fluid interfaces followed by their transfer to solid substrates represents a robust bottom-up strategy for creating colloidal monolayers over large, macroscopic areas. In this study, we showcase how subtle adjustments in the transfer process, such as varying the contact angle of the substrate and controlling deposition speed and direction, enable the realization of all five two-dimensional Bravais lattices. Leveraging plasmonic core–shell microgels as the building blocks, we successfully engineered non-close-packed plasmonic lattices exhibiting hexagonal, square, rectangular, centered rectangular, and oblique symmetries. Beyond characterizing the monolayer structures and their long-range order, we employed extinction spectroscopy alongside finite difference time domain simulations to comprehensively investigate and interpret the plasmonic response of these monolayers. Additionally, we probed the influence of the refractive index environment on the plasmonic properties by two methods: first, by plasma treatment to remove the microgel shells, and second, by overcoating the resulting gold nanoparticle lattices with a homogeneous refractive index polymer film. Graphical Abstract

Chemistry↗

DOE OSTI2025

Composite biopolymer electrolytes for high-performance reversible zinc-air batteries

Zinc-air batteries (ZABs) are regarded as one of the most promising candidates for next-generation energy storage systems due to their inherent safety, high energy density, and low cost. In this study, we optimized the composition of gel polymer electrolytes (GPEs), which play a crucial role in enhancing ZAB reversibility due to their water retention capabilities. The GPEs are synthesized using a combination of polyacrylic acid (PAA), polyacrylamide (PAM), and biopolymer kappa-carrageenan (KC), with and without additional additives. Among these, the composite GPE containing KC, PAA, and PAM demonstrated superior ionic conductivity (6.68 mS/cm at 30 °C) and enhanced water retention compared to the PAA–PAM-based GPE. Furthermore, this composite electrolyte operates within a wider electrochemical window of −1.0 V–2.2 V. A bifunctional catalyst, nickel–iron layered double hydroxide (NiFe-LDH), is electrochemically synthesized on a modified activated carbon cloth (CC). The catalyst loading is optimized based on oxygen evolution reaction (OER) performance, showing an overpotential of 555 mV. The oxygen reduction reaction (ORR) occurred at a half-wave potential of 0.620 V, which is lower than that of Pt/C (0.852 V), indicating better catalytic activity. The KC based cell exhibit better cycling stability than PAA–PAM-based GPE. The electrochemical performance of ZAB cells is evaluated under various atmospheres: ambient air and humid conditions and temperatures. Notably, in a humid environment, the cells achieved extended cycling stability, operating for over 500 h—significantly longer than under open-air conditions. Overall, this study highlights the importance of tailored GPE design and efficient bifunctional catalysts to enhance the performance and longevity of zinc-air batteries for long-duration energy storage applications.

Catalyst↗

DOE OSTI2019

Additively Manufactured Intensified Device for Enhanced Carbon Capture

Additively manufactured packed bed devices for the enhancement of carbon capture were successfully developed, built, characterized, and tested in this project. The objective was to demonstrate that in situ cooling of chemical absorption could have beneficial effects on the absorption rate of CO 2 . This was achieved in two stages, divided between FY 2018 and FY 2019. First, the feasibility of printing conventional packing elements was investigated, and the core hydrodynamic metrics were experimentally validated. The data obtained in those studies informed the operating conditions set for the next stage, which was to validate the efficacy of in situ cooling provided by an additively manufactured packed bed element, referred to as the intensified device. The intensified device is designed to enable heat exchange between an internally flowing coolant and the gas-liquid system flowing on the external corrugated surface of the packing. Polymer and metal were both considered as the base materials for the device, and comparative studies on hydrodynamic properties were performed. These considerations, as well as thermal properties and leak tests led to aluminum being chosen as the base material for experimental validation of capture enhancement. The experimental validation was first conducted under non-reactive conditions, and after establishing heat-exchange capabilities, was subsequently conducted under reactive conditions. These studies demonstrated that in situ cooling can benefit absorption given the appropriate operating conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1985

Effects of the Low Earth Orbital environment on spacecraft materials

Recession of organic-polymer-based surfaces due to oxidation by atomic oxygen, the major component of the LEO environment, was studied in Space Shuttle flights 5, 8, and 41-G to measure reaction rates and the effects of various parameters on reaction rates. Surface recession on the flights indicates reaction rates of 3 x10 to the minus 24th power cc atom for unfilled organic polymers. Application of these rates to Space Station-type exposure for main structural items indicates that as much as 0.075 cm of surface recession occurs in 30 yr. Because of the importance of this effect on Space Station systems, additional experiments are planned to obtain better reaction rate measurements ensuring and adequate data base for Space Station design.

Leger, L. J.↗

NASA NTRS1993

Determination of plate wave velocities and diffuse field decay rates with braod-band acousto-ultrasonic signals

Lowest symmetric and lowest antisymmetric plate wave modes were excited and identified in broad-band acousto-ultrasonic (AU) signals collected from various high temperature composite materials. Group velocities have been determined for these nearly nondispersive modes. An algorithm has been developed and applied to determine phase velocities and hence dispersion curves for the frequency ranges of the broad-band pulses. It is demonstrated that these data are sensitive to changes in the various stiffness moduli of the materials, in agreement by analogy, with the theoretical and experimental results of Tang and Henneke on fiber reinforced polymers. Diffuse field decay rates have been determined in the same specimen geometries and AU configuration as for the plate wave measurements. These decay rates are of value in assessing degradation such as matrix cracking in ceramic matrix composites. In addition, we verify that diffuse field decay rates respond to fiber/matrix interfacial shear strength and density in ceramic matrix composites. This work shows that velocity/stiffness and decay rate measurements can be obtained in the same set of AU experiments for characterizing materials and in specimens with geometries useful for mechanical measurements.

Kautz, Harold E.↗

NASA NTRS2010

Advanced Flip Chips in Extreme Temperature Environments

The use of underfill materials is necessary with flip-chip interconnect technology to redistribute stresses due to mismatching coefficients of thermal expansion (CTEs) between dissimilar materials in the overall assembly. Underfills are formulated using organic polymers and possibly inorganic filler materials. There are a few ways to apply the underfills with flip-chip technology. Traditional capillary-flow underfill materials now possess high flow speed and reduced time to cure, but they still require additional processing steps beyond the typical surface-mount technology (SMT) assembly process. Studies were conducted using underfills in a temperature range of -190 to 85 C, which resulted in an increase of reliability by one to two orders of magnitude. Thermal shock of the flip-chip test articles was designed to induce failures at the interconnect sites (-40 to 100 C). The study on the reliability of flip chips using underfills in the extreme temperature region is of significant value for space applications. This technology is considered as an enabling technology for future space missions. Flip-chip interconnect technology is an advanced electrical interconnection approach where the silicon die or chip is electrically connected, face down, to the substrate by reflowing solder bumps on area-array metallized terminals on the die to matching footprints of solder-wettable pads on the chosen substrate. This advanced flip-chip interconnect technology will significantly improve the performance of high-speed systems, productivity enhancement over manual wire bonding, self-alignment during die joining, low lead inductances, and reduced need for attachment of precious metals. The use of commercially developed no-flow fluxing underfills provides a means of reducing the processing steps employed in the traditional capillary flow methods to enhance SMT compatibility. Reliability of flip chips may be significantly increased by matching/tailoring the CTEs of the substrate material and the silicon die or chip, and also the underfill materials. Advanced packaging interconnects technology such as flip-chip interconnect test boards have been subjected to various extreme temperature ranges that cover military specifications and extreme Mars and asteroid environments. The eventual goal of each process step and the entire process is to produce components with 100 percent interconnect and satisfy the reliability requirements. Underfill materials, in general, may possibly meet demanding end use requirements such as low warpage, low stress, fine pitch, high reliability, and high adhesion.

Ramesham, Rajeshuni↗

NASA NTRS2011

Novel Low-Density Ablators Containing Hyperbranched Poly(azomethine)s

An ablative composite is low-density (0.25 to 0.40 g/cu cm), easy to fabricate, and superior to the current state-of-the-art ablator (phenolic impregnated carbon ablator, PICA) in terms of decomposition temperature, char yield, and mechanical strength. Initial ablative testing with a CO2 laser under high-heat-flux (1,100 W/sq cm) conditions showed these new ablators are over twice as effective as PICA in terms of weight loss, as well as transfer of heat through the specimen. The carbon fiber/poly(azomethine) composites have the same density as PICA, but are 8 to 11 times stronger to irreversible breaking by tensile compression. In addition, polyazomethine char yields by thermogravimetric analysis are 70 to 80 percent at 1,000 C. This char yield is 10 to 20 percent higher than phenolic resins, as well as one of the highest char yields known for any polymer. A high char yield holds the composite together better toward shearing forces on reentry, as well as reradiates high heat fluxes. This innovative composite is stronger than PICA, so multiple pieces can be sealed together without fracture. Researchers have also studied polyazomethines before as linear polymers. Due to poor solubility, these polymers precipitate from the polymerization solvent as a low-molecular-weight (2 to 4 repeat units) powder. The only way found to date to keep linear polyazomethines in solution is by adding solubilizing side groups. However, these groups sacrifice certain polymer properties. These hyperbranched polyazomethines are high molecular weight and fully aromatic.

Tigelaar, Dean↗

NASA NTRS2019

NASA Centennial Challenge: 3D Printed Habitat, Phase 3 Final Results

NASA's Centennial Challenges program uses prize competitions with the goal of accelerating innovation in the aerospace industry. Competitions in the Centennial Challenges portfolio have previously focused on advancements in space robotics, regolith excavation, bio-printing, astronaut suit design, small satellites, and solar-powered vehicles. NASA's Three Dimensional (3D) Printed Habitat Centennial Challenge represents a partnership between NASA and the non-profit partner: Bradley University, with co-sponsors Caterpillar, Bechtel, Brick and Mortar Ventures, the American Concrete Institute, and the United States Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC) to spur development in automated additive construction technologies. The challenge asks teams to design and construct a scaled and simulated Martian habitat using indigenous materials and large scale 3D automated printing systems. Phase 1 of the competition, held in 2015, was an architectural design competition for habitat concepts that could be 3D printed. Phase 2, completed in 2017, asked teams to develop feedstocks from indigenous materials and hydrocarbon polymer recyclables, and demonstrate automated printing systems to manufacture these feedstocks into test specimens to assess mechanical strength. This paper will discuss the Phase 3 competition, focusing on technology outcomes that can potentially be infused into both terrestrial and planetary construction applications. The Phase 3 competition was divided into two sub-competitions: 1) virtual construction, where teams created a high fidelity building information model (BIM) of their 3D-printed habitat design and 2) the construction competition, which required teams to 3D print a structural foundation and subject materials samples to freeze/thaw testing and impact testing (level 1), produce a habitat element and complete a hydrostatic test (level 2), and additively manufacture a 1:3 scale habitat onsite in a head to head competition at Caterpillar, inc.'s Edwards Demonstration & Learning Center near Peoria, Illinois over the course of three days (level 3). While the Phase 2 competition focused primarily on the development of novel feedstocks and robotic printing systems, Phase 3 emphasized the scale-up of these systems and autonomous operation (demonstrating the capability to operate systems on precursor missions prior to the arrival of crew, or terrestrially in field operation settings where human tending of a manufacturing system may be limited). The Phase 3 virtual construction levels yielded a number of novel habitat designs, including both modular habitats and vertically-oriented habitat concepts. The Phase 3 construction competition also challenged teams to autonomously place penetrations and interfacing elements in additively manufactured structures. The paper will emphasize potential applications for the new materials and technologies developed under the umbrella of the competition within NASA's portfolio and in Earth-based applications such as disaster response and infrastructure improvement.

Construction↗

NASA NTRS2019

Nasa Centennial Challenge: Three Dimensional (3d) Printed Habitat, Phase 3

Centennial challenge↗

DOE OSTI2025

Ultra-selective CANAL Polymers for Hydrogen-based Membrane Separations after Long-Term Aging

Hydrogen is a critically important molecule in the chemicals and energy industries, driving the need for efficient purification technologies such as membrane-based separations. However, polymer membranes often suffer from physical aging, leading to decreased gas permeability over time. This study leverages the unique aging behavior of contorted microporous polymers, synthesized via catalytic arene-norbornene annulation (CANAL) polymerization, to enhance molecular sieving for H 2 separations. While prior studies demonstrated a 1000% increase in H 2 /CH 4 selectivity with minimal permeability loss over 150 days, we extend this investigation to hyperaged (∼1 year) CANAL polymers and evaluate their performance under various conditions of industrial relevance. We report a remarkable 6100% increase in H 2 /CH 4 selectivity and a 2400% improvement in H 2 /N 2 selectivity, with only a 55% decline in H 2 permeability. These membranes exhibit excellent long-term stability in binary and ternary gas mixtures and at elevated temperatures. Additionally, extended aging enhances H 2 /CO 2 selectivity beyond the 2008 upper bound due to improved size-sieving. High-temperature permeation experiments and grand canonical Monte Carlo simulations reveal that H 2 permeability increases from 570 to 3500 barrer as the temperature rises from 35 °C to 190 °C, while H 2 /CO 2 selectivity declines from 14 to 3 due to the higher diffusion activation energy of CO 2 . Despite this tradeoff, hyperaged CANAL membranes maintain performance beyond the 200 °C upper bound, having selectivity–permeability performance comparable to many state-of-the-art membranes for H 2 /CO 2 separations. As a result, this study highlights the robustness and industrial viability of ultra-selective CANAL polymers for hydrogen purification, contributing to advancements in clean energy and sustainable separation technologies.

36 MATERIALS SCIENCE↗