Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optimization for fusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

LDRD Final Report: Advanced Hohlraum Concepts

Indirect drive inertial confinement fusion (ICF) experiments to date have mostly used cylindrical, laser-heated, gas-filled hohlraums to produce the radiation drive needed to symmetrically implode DT-filled fusion capsules. These hohlraums have generally been unable to produce a symmetric radiation drive through the end of the desired drive pulse, and are plagued with complications due to laser-plasma interactions (LPI) that have made it difficult to predict their performance. In this project we developed several alternate hohlraum concepts. These new hohlraums utilize different hohlraum geometries, radiation shields, and foam materials in an attempt to improve performance relative to cylindrical hohlraums. Each alternate design was optimized using radiation hydrodynamic (RH) design codes to implode a reference DT capsule with a high-density carbon (HDC) ablator. The laser power and energy required to produce the desired time-dependent radiation drive, and the resulting time-dependent radiation symmetry for each new concept were compared to the results for a reference cylindrical hohlraum. Since several of the new designs needed extra laser entrance holes (LEHs), techniques to keep small LEHs open longer, including high-Z foam liners and low-Z wires at the LEH axis, were investigated numerically. Supporting experiments and target fabrication efforts were also done as part of this project. On the Janus laser facility plastic tubes open at one end (halfraums) and filled with SiO 2 or Ta 2 O 5 foam were heated with a single 2w laser. Laser propagation and backscatter were measured. Generally the measured propagation was slower than calculated, and the measured laser backscatter was less than calculated. A comparable, scaled up experiment was designed for the NIF facility and four targets were built. Since low density gold foam was identified as a desirable material for lining the LEH and the hohlraum wall, a technique was developed to produce 550 mg/cc gold foam, and a sample of this material was successfully manufactured.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A high resolution Mirnov array for the Mega Ampere Spherical Tokamak

Over the past two decades, the increase in neutral-beam heating and {alpha} particle production in magnetically confined fusion plasmas has led to an increase in energetic particle driven mode activity, much of which has an electromagnetic signature which can be detected by the use of external Mirnov coils. Typically, the frequency and spatial wave number band of such oscillations increase with increasing injection energy, offering new challenges for diagnostic design. In particular, as the frequency approaches the megahertz range, care must be taken to model the stray capacitance of the coil, which limits the resonant frequency of the probe; model transmission line effects in the system, which if unchecked can produce system resonances; and minimize coil conductive shielding, so as to minimize skin currents which limit the frequency response of the coil. As well as optimizing the frequency response, the coils should also be positioned to confidently identify oscillations over a wide wave number band. This work, which draws on new techniques in stray capacitance modeling and coil positioning, is a case study of the outboard Mirnov array for high-frequency acquisition in the Mega Ampere Spherical Tokamak, and is intended as a roadmap for the design of high frequency, weak field strength magnetic diagnostics.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Studying converging shock collisions in novel hybrid-drive shock ignition geometries

Recent Inertial Confinement Fusion (ICF) experiments using a “high-foot” implosion at the National Ignition Facility (NIF) have demonstrated the importance of hydrodynamic stability in these systems by reaching the alpha heating regime and setting new records of energy gain. The high-foot platform is not predicted to achieve ignition, however, and consequently must sacrifice some stability for increased kinetic energy delivered to the fuel in experiments planned for the near future as an optimal, ignition achieving target design is searched for. Given that the high-foot fuel implosion velocity was measured to reach 310 km/s (390 TW, 1.8 MJ 3-­shock pulse) whereas the low-­foot, high mix implosions of the original National Ignition Campaign (NIC) reached 350 km/s (420 TW, 1.6 MJ 4-­shock pulse) with a predicted velocity requirement of 370 km/s (based on 2-­D simulations used to define an Ignition Threshold Factor) we are left with an extremely narrow margin for success just by optimizing between the high and low-foot platforms. There is hope that alternate ablators will also provide some performance improvements, but it appears likely that no manifestation of the conventional indirect-­drive central hotspot implosion scheme (C-­ICF) will work with the current available facility energy. This by itself motivates the need to seek alternate fuel assembly concepts that can be fielded on NIF in the near future. At a fundamental level Shock Ignition (SI) is predicted to make more efficient use of the total energy available from the driver (i.e. NIF or OMEGA) and to result in higher gains needed for energy production, which makes it a likely candidate as an alternative ignition approach. The direct irradiation of the capsule to drive the implosion, however, is untested at ignition-­scale and poses numerous difficulties on NIF. If the implosion was driven using a hohlraum (indirectly) instead followed by direct laser irradiation of the imploded capsule to launch the ignitor shock (as illustrated in the upper panel of Fig. 1) then this form of Shock Ignition could fit well into the NIF environment. The primary objective of this project is to develop and test a hybrid drive implosion concept on OMEGA to study its merits and weaknesses for eventual trial on NIF. A key question that remains with regards to Shock Ignition, in general, is the effect of low­-mode asymmetries on the transfer of energy during collision of the rebounding and ignitor shocks. Our second objective is to field a directed experiment designed to study asymmetric converging shock collision and their effect on hot spot formation. The proposed experiments are part of a current LANL Laboratory Directed Research and Development (LDRD) project that we are using to develop ignition-scale designs as well as for designing and carrying out the first implosion experiments as discussed below.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimal control model of technology transition.

This paper discusses the use of optimization software to solve an optimal control problem arising in the modeling of technology transition. We set up a series of increasingly complex models with such features as learning-by-doing, adjustment cost, and capital investment. The models are written in continuous time and then discretized by using different methods to transform them into large-scale nonlinear programs. We use a modeling language and numerical optimization methods to solve the optimization problem. Our results are consistent with findings in the literature and highlight the impact the discretization choice has on the solution and accuracy. The primary goal of this paper is to develop solution methods for use in policy work. To do this, we will need to expand the model to include realistic features such as additional technologies and capital conversion. Our modeling approach allows us to add new technologies with minimal effort. For example, Figure 5 presents the solution to the capital model that includes a third technology, say, nuclear fusion, that is emission free but even more expensive (A{sub 3} > A{sub n}). We observe that industry first transitions to the intermediate technology but eventually adopts the cleanest one. We note that our solutions have few areas of large curvature and are relatively smooth elsewhere. On such smooth segments, we can achieve adequate precision with relatively large periods, which means fewer variables and increased computation speed. But we still need a small step length during the transition period. Adaptive mesh refinement methods have been developed to automatically identify the areas where extra precision is needed. Betts (2001) describes how the computation time can be reduced by a factor of 2.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Collection of solid and gaseous samples to diagnose inertial confinement fusion implosions

Collection of representative samples of debris following inertial confinement fusion implosions in order to diagnose implosion conditions and efficacy is a challenging endeavor because of the unique conditions within the target chamber such as unconverted laser light, intense pulse of x-rays, physical chunks of debris, and other ablative effects. We present collection of gas samples following an implosion for the first time. High collection fractions for noble gases were achieved. We also present collection of solid debris samples on flat plate collectors. Geometrical collection efficiencies for Au hohlraum material were achieved and collection of capsule debris (Be and Cu) was also observed. Asymmetric debris distributions were observed for Au and Be samples. Collection of Be capsule debris was higher for solid collectors viewing the capsule through the laser entrance hole in the hohlraum than for solid collectors viewing the capsule around the waist of the hohlraum. Collection of Au hohlraum material showed the opposite pattern: more Au debris was collected around the waist than through the laser entrance hole. The solid debris collectors were not optimized for minimal Cu backgrounds, which limited the conclusions about the symmetry of the Cu debris. The quality of the data limited conclusions on chemical fractionation effects within the burning, expanding, and then cooling plasma.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Ultra-rapid, physics-based development pathway for reactor-relevant RF antenna materials

This paper presents a rapid, atomistically-informed, experimental development pathway for fusion reactor-relevant radio frequency (RF) antenna materials in the Cu-Cr-(Nb,Al,Zr) composition system, with the goal of improving upon GRCop-84. RF antennas in a tokamak fusion reactor will face a unique set of challenges as both structural and functional materials. The desired material must simultaneously achieve and maintain high electrical conductivity, high strength, high thermal conductivity, resist high temperatures, possess low nuclear activation, and incur low damage due to neutron bombardment. The GRCop-84 alloy serves as a starting point for iterative improvement, with the desire to reduce or eliminate Nb from the material to minimize nuclear activation. The rapid development pathway makes use of a multi-target combinatorial thick film sputtering process to produce full ternary phase diagrams on a Si wafer substrate. Transient grating spectroscopy (TGS), a laser-ultrasonic method, will determine spatially-varying thermo-elastic properties, while four terminal electrical conductivity measurements will map out the best per- forming regions of the sample for in-depth study at larger length scales. High energy proton and self-ion irradiation emulates the effects of neutron damage on the thermal/electric properties. With rapid turnaround time (∼days) in terms of mapping radiation damage-induced material property changes in the full ternary system, these techniques allow rapid iteration towards an optimal material, testing hundreds of nearby compositions in the time it took to test one. Focused testing of larger, single composition samples (produced in an arc furnace or by laser sintering) provides data on structural and high power RF properties, and validates our thick-film based workflow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct Laser Impulse (DLI) System Alignment: Requirements Engineering Project

The National Ignition Facility (NIF) is the world’s largest and most energetic laser, and it is comprised of 192 laser beams that must align onto one target for the purpose of learning about Internal Confinement Fusion (ICF) and High Energy Density (HED) physics. A new NIF capability under development is the Direct Laser Impulse (DLI). The DLI capability will provide a test environment where high pulsed laser energy is delivered to a three-dimensional target. Achieving this delivery to target relies on a precision alignment and positioning of the two redirected NIF beams, as shown in Figure 1. When aligned, the two combined beams—with a frequency converted from infrared (IR) to green laser light, at a fluence (energy per unit area) of roughly 20 joules per square centimeter—will be capable of delivering up to 30 kilojoules of direct, unfocused energy to a one cubic foot target. The 40-cm x 40-cm aligned impulse area at the DLI target interaction plane (TIP) is achieved by using a beam path comprised of pickoff and transport mirrors, frequency conversion crystals, optics serving as environmental barriers, and debris shields. A separate aligned diagnostic beam path is also required for impulse to TIP characterization. Final in-situ alignment is required for the two populated diverted NIF beam paths onto the DLI target as well as the diagnostic optical beam path. Existing NIF alignment subsystems do not offer references that meet DLI’s unique demand. The new DLI Red Box, which has been designed to allow for alignment, has been shown to require deviation from the intended configuration and operational use case to obtain adequate functionality. A systems engineering evaluation has identified a solution that meets the stakeholder requirements while optimizing key performance parameters. The solution, referred to in this document as the Red Box “+” Rotated, was determined to be an improved version of the current DLI Red Box. This system offers improved system repeatability and alignment stability while maintaining similar interfaces and decreasing the demand for engineer/operator interaction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

General design of the International Fusion Materials Irradiation Facility deuteron injector: Source and beam line

In the framework of the International Fusion Materials Irradiation Facility-Engineering Validation and Engineering Design Activities (IFMIF-EVEDA) project, CEA/IRFU is in charge of the design and realization of the 140 mA cw deuteron Injector. The electron cyclotron resonance ion source operates at 2.45 GHz and a 4 electrode extraction system has been chosen. A 2 solenoid beam line, together with a high space charge compensation have been optimized for a proper beam injection in the 175 MHz radio frequency quadrupole. The injector will be tested with proton and deuteron beam production either in pulsed mode or in cw mode on the CEA-Saclay site before to be shipped to Japan. Special attention was paid to neutron emission due to (d,D) reaction. In this paper, the general IFMIF Injector design is reported, pointing out beam dynamics, radioprotection, diagnostics, and mechanical aspects.

43 PARTICLE ACCELERATORS↗

In the grass species Brachypodium distachyon , the production of mixed-linkage (1,3;1,4)-β-glucan (MLG) occurs in the Golgi apparatus

Mixed-inkage (1,3;1,4)-β-glucan (MLG) is a glucose polymer with beneficial effects on human health and high potential for the agricultural industry. MLG is present predominantly in the cell wall of grasses and is synthesized by cellulose synthase-like F or H families of proteins, with CSLF6 being the best-characterized MLG synthase. Although the function of this enzyme in MLG production has been established, the site of MLG synthesis in the cell is debated. It has been proposed that MLG is synthesized at the plasma membrane, as occurs for cellulose and callose; in contrast, it has also been proposed that MLG is synthesized in the Golgi apparatus, as occurs for other matrix polysaccharides of the cell wall. Testing these conflicting possibilities is fundamentally important in the general understanding of the biosynthesis of the plant cell wall. Using immuno-localization analyses with MLG-specific antibody in Brachypodium and in barley, we found MLG present in the Golgi, in post-Golgi structures and in the cell wall. Accordingly, analyses of a functional fluorescent protein fusion of CSLF6 stably expressed in Brachypodium demonstrated that the enzyme is localized in the Golgi. We also established that overproduction of MLG causes developmental and growth defects in Brachypodium as also occur in barley. Our results indicated that MLG production occurs in the Golgi similarly to other cell wall matrix polysaccharides, and supports the broadly applicable model in grasses that tight mechanisms control optimal MLG accumulation in the cell wall during development and growth. This work addresses the fundamental question of where mixed linkage (1,3;1,4)-β-glucan (MLG) is synthesized in plant cells. By analyzing the subcellular localization of MLG and MLG synthase in an endogenous system, we demonstrated that MLG synthesis occurs at the Golgi in Brachypodium and barley. In conclusion, a growth inhibition due to overproduced MLG in Brachypodium supports the general applicability of the model that a tight control of the cell wall polysaccharides accumulation is needed to maintain growth homeostasis during development.

59 BASIC BIOLOGICAL SCIENCES↗

Optimizing Laser-accelerated Ion Beams for a Collimated Neutron Source

High-flux neutrons for imaging and materials analysis applications have typically been provided by accelerator- and reactor-based neutron sources. A novel approach is to use ultraintense (>1018W/cm2) lasers to generate picosecond, collimated neutrons from a dual target configuration. In this article, the production capabilities of present and upcoming laser facilities are estimated while independently maximizing neutron yields and minimizing beam divergence. A Monte-Carlo code calculates angular and energy distributions of neutrons generated by D-D fusion events occurring within a deuterated target for a given incident beam of D+ ions. Tailoring of the incident distribution via laser parameters and microlens focusing modifies the emerging neutrons. Projected neutron yields and distributions are compared to conventional sources, yielding comparable on-target fluxes per discharge, shorter time resolution, larger neutron energies and greater collimation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimized recursion relation for the computation of partition functions in the superconfiguration approach

Partition functions of a canonical ensemble of non-interacting bound electrons are a key ingredient of the super-transition-array approach to the computation of radiative opacity. A few years ago, we published a robust and stable recursion relation for the calculation of such partition functions. In this work, we propose an optimization of the latter method and explain how to implement it in practice. The formalism relies on the evaluation of elementary symmetric polynomials, which opens the way to further improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stellarator optimization with constraints

In this work we consider the problem of optimizing a stellarator subject to hard constraints on the design variables and physics properties of the equilibrium. We survey current numerical methods for handling these constraints, and summarize a number of methods from the wider optimization community that have not been used extensively for stellarator optimization thus far. We demonstrate the utility of new methods of constrained optimization by optimizing a quasi-axisymmetric stellarator for favourable physics properties while preventing strong shaping of the plasma boundary, which can be difficult to create with external current sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Error-field induced electromagnetic torques in a large aspect-ratio, low-{beta}, weakly shaped tokamak plasma

The toroidal electromagnetic braking torques exerted at the various internal rational surfaces of a large aspect-ratio, low-{beta}, weakly shaped, tokamak plasma by a nonaxisymmetric error field are investigated using a semianalytic approach. It is found that there is an optimal error-field spectrum for exerting a torque at a given rational surface. This spectrum is dominated by the resonant harmonic, but also contains sideband harmonics induced by plasma toroidicity, pressure, ellipticity, and triangularity. These sidebands couple back to the resonant harmonic in such a manner as to reduce its amplitude. Provided that there is significant coupling to a (stable) ideal external kink mode which is close to its marginal stability boundary, the optimal error field predominately contains sideband harmonics whose poloidal mode numbers are more positive than the resonant mode number (which is assumed to be positive), and also tends to balloon on the outboard side of the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Bio-Nano ECRIS: An electron cyclotron resonance ion source for new materials production

We developed an electron cyclotron resonance ion source (ECRIS) for new materials production on nanoscale. Our main target is the endohedral fullerenes, which have potential in medical care, biotechnology, and nanotechnology. In particular, iron-encapsulated fullerene can be applied as a contrast material for magnetic resonance imaging or microwave heat therapy. Thus, our new ECRIS is named the Bio-Nano ECRIS. In this article, the recent progress of the development of the Bio-Nano ECRIS is reported: (i) iron ion beam production using induction heating oven and (ii) optimization of singly charged C{sub 60} ion beam production.

36 MATERIALS SCIENCE↗

Density profile sensitivity study of ASDEX Upgrade ICRF Antennas with the TOPICA code

During operation of the ASDEX Upgrade (AUG) ion cyclotron radio frequency (ICRF) system, Tungsten (W)-coated poloidal limiters and structures connected along magnetic field lines to the antenna can be sources of W, which is attributed to sputtering by ions accelerated in radio frequency (RF) sheaths. In order to analyze and optimize the ICRF antenna performance, accurate and efficient simulation tools are necessary. TOPICA code was developed for analysis of ICRF antenna systems with plasma loading conditions modeled with ID FELICE code. This paper presents an initial comparative analysis of two AUG ICRF antennas for a set of model plasma density profiles (with varying density gradient and antenna cut-off distance). The antennas are presently installed in AUG and differ in that one was partially optimized using HFSS code to reduce E{sub ||} near fields. Power transferred to plasma and sheath driving RF potentials are computed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shock formation in Ne, Ar, Kr, and Xe on deuterium gas puff implosions

1- and 2-D simulations of 1-cm radius, gas-puff liners of Ne, Ar, Kr, and Xe imploding onto a deuterium target are conducted using the discharge parameters for the Zebra (1 MA, 130 ns) driver using the resistive MHD code MACH2. This is an implementation of the Staged Z-pinch concept, in which the target is driven to high-energy-density first by shock compression launched by a diffused azimuthal magnetic field (J×B force), and then by the adiabatic compression as the liner converges on axis. During the run-in phase, the initial shock heating preheats the deuterium plasma, with a subsequent stable, adiabatic compression heating the target to high energy density. Shock compression of the target coincides with the development of a J×B force at the target/liner interface. Stronger B-field transport and earlier shock compression increases with higher-Z liners, which results in an earlier shock arrival on axis. As a result, delayed shock formation in lower-Z liners yields a relative increase in shock heating, however, the 2-D simulations show an increased target isolation from magneto-Rayleigh-Taylor instability penetration, suggesting that an optimal balance between these two effects is reached in an Ar or Kr liner, rather than with Xe.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The root cause of disruptive NTMs and paths to stable operation in DIII-D ITER baseline scenario plasmas

Analyses of the DIII-D ITER Baseline Scenario database support that the disruptive m,n=2,1 magnetic islands are pressure gradient driven, non-linear instabilities seeded in a sequence of stochastic transient magnetic perturbations, and that the current profile relaxation does not affect the m,n=2,1 island onset rate. At low torque, these Neoclassical Tearing Modes are most commonly seeded by non-linear 3-wave coupling when the differential rotation between the q=1 & q=2 rational surfaces approaches zero. Lack of statistically significant difference between the current profiles of stable and unstable states, as well as lack of correlation between the tearing mode onset rate and the current profile relaxation both reject causality between the current profile evolution and the 2,1 magnetic island onsets in these plasmas. These support that preserving the differential rotation between the q=1 and q=2 rational surfaces is key to long pulse stable operation in the plasma scenario planned for ITER, while optimization of the current profile within the explored parameter space may lead to much weaker improvements than sustaining the differential rotation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗