Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Influence of Packing Atmosphere on the Microstructures and Transport Properties of Bi-2223/AgAu Tapes

Oxygen partial pressure was the key factor to tune the phase evolution mechanism of Bi-2223 system. In order to investigate the influence of packing atmosphere on the phase formation rate of Bi-2223, microstructures‚ and the current capacity of final tapes‚ 37-filamentary Bi-2223/AgAu tapes were fabricated by powder-in-tube (PIT) process, and the powder packing process operated in the glove box under different atmosphere of pure O{sub 2}‚ air, and N{sub 2}–7.5%O{sub 2}, with the oxygen partial pressure of 100%‚ 25%, and 7.5%, respectively. With different packing atmosphere, the phase formation rate of Bi-2223 increased obviously during the first heat treatment process (HT1). While, based on the same HT1 process, the maximum Bi-2223 phase content was obtained in the tapes with packing atmosphere of N{sub 2}–7.5%O{sub 2}‚ which should be attributed to the suitable Bi-2223 content and distribution. Due to the improvement of superconducting phase content and better texture structure, the critical current density increased with decreasing oxygen partial pressure of packing atmosphere and the maximum value of 19.9 kA/cm{sup 2} was reached. Moreover‚ the in-field current capacities of these Bi-2223/AgAu tapes have also been enhanced with low oxygen partial pressure in packing atmosphere, attributed to the improvements of intergrain connectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Influence of Annealing on Microstructure, Electrochemical, and Magnetic Properties of Co-Doped SrTiO{sub 3} Nanocubes

Effect of annealing on microstructure, electrochemical, and magnetic properties of Co-doped SrTiO{sub 3} nanocubes obtained by the hydrothermal method was studied. X-ray diffraction (XRD) results of all as-prepared and annealed Co-doped SrTiO{sub 3} samples revealed a cubic perovskite structure with the second phases of SrCO{sub 3} and Co{sub 3}O{sub 4}in as-prepared and annealed SrTi{sub 0.90}Co{sub 0.10}O{sub 3} samples, respectively. Agglomerated nanocubes could be clearly observed in all as-prepared and annealed Co-doped samples by scanning electron microscope (SEM) and transmission electron microscope (TEM). X-ray absorption near edge spectroscopy (XANES) results suggested the presence of Co{sup 2+} cations in as-prepared Co-doped SrTiO{sub 3} samples, while both of Co{sup 2+} and Co{sup 3+} cations were found in annealed Co-doped SrTiO{sub 3} samples. The cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) results of as-prepared and annealed SrTi{sub 1-x}Co{sub x}O{sub 3} (x = 0.05, 0.075 and 0.10) electrodes revealed pseudocapacitor behavior of the Faradaic redox reaction type. The specific capacitance (Csc) was affected by the increase of Co content in all as-prepared and annealed Co-doped SrTiO{sub 3} samples with an excellent cycling stability after 200 cycle test of 97.24% and the highest value of 75.28 F g{sup −1} at 1 A g{sup −1} in an annealed SrTi{sub 0.925}Co{sub 0.075}O{sub 3} electrode. Magnetization measurements at room temperature using vibrating sample magnetometer (VSM) revealed diamagnetic behavior of as-prepared SrTiO{sub 3} sample, whereas paramagnetic behavior was observed in all as-prepared Co-doped SrTiO{sub 3} samples. After annealing, undoped sample exhibited paramagnetic behavior, whereas ferromagnetic behavior was observed in all Co-doped SrTiO{sub 3} samples with the increase of saturation magnetization (M{sub s}) at 10 kOe from 0.58 to 1.63 emu/g and the coercive field (H{sub c}) from 43.71 to 123.87 Oe, suggested to originate from the face-center exchange (FCE) mechanism.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Implications of theoretical analysis to explore the functional core dimension in one-rod core microstructured optical fibers

A new development in optical fiber technology that has attracted interest for multitude of novel and potential applications is an all-in-silica microstructured optical fibre (MOF) with one-rod core. We aim to estimate the functional core dimension for one-rod core triangular MOF (T-MOF) from its geometrical characteristics by using an alternative analytical field model. Moreover, to scrutinize the validity of the choice of effective core dimension (by adapting V-parameter, i.e., the normalized frequency) for T-MOF, we have explored the rudimentary propagation characteristics of the T-MOF in single mode guidance realm. We made comparisons with those which are based on the experimental and numerical studies. Relative errors are also reported.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

The Influence of Microstructure on Oxidation Rate Of V–Cr–Ta–Zr Alloy During Its Chemical-Heat Treatment

Using the methods of scanning (electron backscatter diffraction) and transmission electron microscopy, an investigation of the influence of microstructure of a V–Cr–Ta–Zr alloy on the rate of surface oxide scale formation in the course of its chemical-heat treatment using oxidation in air is performed. It is shown that a preliminary plastic deformation, ensuring a multiple increase in the density of dislocations and misorientation boundaries, results in a 10% thicker surface oxide layer and a respective increase in the concentration of oxygen in the alloy during the final stage of its chemical-heat treatment. The role of this factor in developing the chemical-heat treatment regimes is discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Special Aspects of Microstructure, Deformation and Fracture of Bioinert Zirconium and Titanium-Niobium Alloys in Different Structural States

The characteristics of microstructure, deformation and fracture of Zr – 1 wt% Nb and Ti – 45 wt% Nb bioinert alloys in the coarse- and ultrafine-grained states are investigated. It is shown that the ultrafine-grained structure formed in them ensures excellent mechanical properties of the alloys and affects the stages of the stress-strain curves and the behavior of the maximum temperature vs. deformation time plot. The formation of an α-phase in the Ti – 45 wt% Nb ultrafine-grained alloy suppresses the linear stage VI characterized by a constant strain hardening coefficient. In stage VII, the strain hardening coefficient rapidly becomes negative, which indicates the material softening prior to its failure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Microstructural Changes and Kinetics of Reduction of Hematite to Magnetite in CO/CO{sub 2} Gas Atmospheres

The microstructures of porous magnetite formed on gaseous reduction of dense hematite have been examined using high-resolution scanning electron microscopy. It has been shown that cellular pores are formed on reduction in the temperature range 573 K to 973 K (300 °C to 700 °C). Dendritic shaped gas pores are formed on reduction at temperatures between 1073 K and 1273 K (800 °C and 1000 °C). The apparent chemical reaction rate constant for the reduction of hematite to magnetite in CO/CO{sub 2} gas mixtures has been derived from measurements of product thickness against reaction time; the rate constant is described by the relation φ{sub CO} = 0.232exp(76,000/RT) µm s{sup −1} atm{sup −1}.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Formation Mechanisms and Microstructure Characterization of Al/Al{sub 3}Ni In-situ Composite by Compound Casting

The Compound casting method was used to produce an Al/Ni bimetal composite. The mechanisms of formation of the reinforcing intermetallic phases were studied and the produced bimetal composite’s microstructure was then characterized. The results showed that the Al/Ni interface consisted of two intermetallic layers including Al{sub 3}Ni{sub 2} and Al{sub 3}Ni. It is suggested that the Al{sub 3}Ni reinforcing particles of the composite originated from two sources. (1) Some Al{sub 3}Ni particles detached from the Al{sub 3}Ni layer formed at the interface between the Ni core and the Al melt and dispersed in the liquid Al and (2) Al-Al{sub 3}Ni eutectic phase, which formed during the solidification process. The increase in the temperature led to the formation of more reinforcing particles and extended the depth of dispersion of the particles in the Al matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Effect of Melt Ultrasound Treatment on the Microstructure and Age Hardenability of Al-4 Wt Pct Cu/TiC Composite

In the present work, Al-4 wt pct Cu/TiC composite was synthesized by the molten salt route that contains submicron-sized TiC particles in the Al-4 wt pct Cu matrix. The concentration of the TiC particle in the base alloy is 7.5 wt pct. Melt ultrasound treatment was done by remelting the as-cast composite at 1023 K (750 °C) in a view to refine the size of TiC particles to nanoscale and distribute them evenly in the matrix. The microstructure and age hardenability of the untreated and ultrasound-treated composites were investigated. The TiC particles accelerate the precipitation kinetics of CuAl{sub 2} phase in Al-4 wt pct Cu alloy. In the present study, the hardness obtained for untreated Al-4 wt pct Cu/TiC composite is 120 VHN within 5 hours of peak aging time, which is higher than the hardness of the monolithic Al-4 wt pct Cu, which is 104 VHN at 35 hours of peak aging time. Melt ultrasound treatment of Al-4 wt pct Cu/TiC composite shows no significant effect on the distribution and refinement of TiC particles in the matrix. However, it partially disintegrates the TiC into Al{sub 3}Ti and Al{sub 4}C{sub 3} particles. The ultrasound-treated composite showed an improved hardness of about 132 VHN at 5 hours of peak aging, in comparison to that of the untreated composite, by forming denser and homogeneous CuAl{sub 2} precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Experimental Investigation of Microstructure and Phase Transitions in Ag-Cu-Zn Brazing Alloys

Microstructure and phase transitions of selected brazing alloys from the Ag-Cu-Zn ternary system were investigated. Four ternary alloys with silver content in the compositional range from 25 to 60 wt.% were studied using x-ray diffraction (XRD) and scanning electron microscopy coupled with the energy-dispersive spectroscopy (SEM–EDS). Phase transitions of the investigated alloys were measured using differential scanning calorimetry (DSC). Experimentally obtained results were compared with the results of a thermodynamic calculation of the phase equilibria according to the CALPHAD method. The experiments confirmed the optimized thermodynamic parameters for the calculations from the thermodynamic assessment in literature. Phase compositions, liquidus and solidus temperatures were confirmed by the EDS and DTA methods. Additionally, the calculated solidification paths and predicted phase transformations were in agreement with the SEM images.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Hot Deformation Behavior and Microstructural Evolution of Antibacterial Austenitic Stainless Steel Containing 3.60% Cu

Hot deformation behavior of as-cast antibacterial austenitic stainless steel containing 3.60% copper was investigated in a temperature range of 900-1150 °C and strain rate range of 0.01-20 s{sup −1}. At strain rates higher than 1 s {sup −1}, the flow stress curves were corrected considering adiabatic heating. Kinetic analysis indicated that the hot deformation activation energy of steel was 376.02 kJ mol{sup −1}. The microstructural evolution under different temperatures was observed by optical microscopy. The nucleation sites for recrystallization and different orientations and twin ratios under different strain rates were analyzed by electron backscatter diffraction. The results showed that hot deformation was dominated by continuous dynamic recrystallization in the high-temperature and high-strain-rate region (1050-1150 °C, 1-20 s{sup −1}). On increasing the temperature and strain rate, the degree of recrystallization and twinning increased simultaneously. These phenomena promoted one another. Thus, the volume fraction of the recrystallized and twinned grains increased with the addition of Cu.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Different Thermomechanical Processes on the Microstructure, Texture, and Mechanical Properties of API 5L X70 Steel

A commercial API 5L X70 steel plate was subjected to different thermomechanical processes to propose a novel thermomechanical rolling path to achieve improved mechanical properties. Scanning electron microscopy, electron backscatter diffraction, and x-ray texture analysis were employed for microstructural characterization. The results showed that strain-free recrystallized {001} ferrite grains that developed at higher rolling temperature could not meet the American Petroleum Institute (API) requirements. Also, refined and work-hardened grains that have formed in the intercritical region with high stored energy do not provide suitable tensile properties. However, fine martensite–austenite constituents dispersed in ferrite matrix with grains having predominantly {111} and {110} orientations parallel to the normal direction that developed under isothermal rolling at 850 °C provided an outstanding combination of tensile strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructural and Mechanical Properties of Hot Roll Bonded Titanium Alloy/Low Carbon Steel Plate

In this paper, a titanium alloy and low carbon steel were bonded via hot rolling in a vacuum, and the effect of roll bonding temperature and reduction ratio on the microstructural and mechanical properties of the plate was studied. When the bonding temperature was between 850 and 1050 °C, the shear strength of the interface increased with an increasing reduction ratio from 18 to 70%. At a bonding temperature of 950 °C and at a rolling reduction ratio of 70%, the best bonding strength was obtained, and a shear fracture occurred on the low carbon steel matrix. At 1050 °C, brittle compounds, i.e., TiC, FeTi, and Fe{sub 2}Ti, formed at the interface, which decreased the bonding strength. The large reduction ratio can break up compounds at the interface and extrude fresh metal for bonding, thereby increasing the bonding strength.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A Comparative Study of the Microstructure, Mechanical Properties and Corrosion Resistance of Ni- or Fe- Based Composite Coatings by Laser Cladding

Ni- and Fe-based composite coatings were laser cladded on 40Cr steel to improve the surface mechanical property and corrosion resistance, respectively. The microstructure and phase composition were analyzed by x-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) equipped with an energy-dispersive spectrometer (EDS). The micro-hardness, tribological properties and electrochemical corrosion behavior of the coatings were evaluated. The results show that the thickness of both the coatings is around 0.7 mm, the Ni-based coating is mainly composed of γ-(Ni, Fe), FeNi{sub 3}, Ni{sub 31}Si{sub 12}, Ni{sub 3}B, CrB and Cr{sub 7}C{sub 3}, and the Fe-based coating is mainly composed of austenite and (Fe, Cr){sub 7}C{sub 3}. Micro-hardness of the Ni-based composite coating is about 960 HV{sub 0.3}, much higher than that of Fe-based coating (357.4 HV{sub 0.3}) and the 40Cr substrate (251 HV{sub 0.3}). Meanwhile, the Ni-based composite coating possesses better wear resistance than the Fe-based coating validated by the worn appearance and the wear loss. Electrochemical results suggested that Ni-based coating exhibited better corrosion resistance than the Fe-based coating. The 40Cr substrate could be well protected by the Ni-based coating.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Mechanical Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration of Zr{sub 2}Cu into Porous Preforms from Partially Carburized W Powders

W-ZrC composites with different W contents from 48 to 73 vol.% have been synthesized by reactive melt infiltration of Zr{sub 2}Cu melt into porous preforms from partially carburized W powders at 1300 °C for 1 h in vacuum. The influences of carbon content and porosity in the preforms on microstructure and mechanical properties of W-ZrC composites are investigated. Cold isostatic pressing followed by pre-sintering process is used to produce porous preforms with suitable porosities of 53.6-47% under a pressure of 100 MPa to allow sufficient penetration of Zr{sub 2}Cu melt into the preforms. Small amounts of Cu-rich phases form in the synthesized W-ZrC composites after a complete reaction of y/2xZr{sub 2}Cu(l) + WC{sub y}(s) = y/xZrC{sub x}(s) + W(s) + y/2xCu(l). These Cu-rich phases are distributed not only at the phase boundaries of W matrix and ZrC grains, but also in the interior of ZrC{sub x} grains. With decreasing W content from 73 to 48 vol.% in the W-ZrC composites, the flexural strength and fracture toughness increase from 519 to 657 MPa and from 9.1 to 10.6 MPa m{sup 1/2}, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of the As-Forged and Heat-Treated Microstructure on the Room Temperature Anisotropic Ductile Fracture of Inconel 718

The purpose of the present work was to investigate the effect of primary carbides and the δ-phase on the anisotropic ductile fracture of Inconel 718 in the forging process. Inconel 718 alloys were prepared by VIM + VAR processes with various carbon contents (0.009 and 0.027 wt.%). Then, the alloys were forged and annealed at temperatures of 980 and 1030 °C. The room temperature mechanical anisotropy of the alloys was evaluated at the longitudinal direction (LD) and transverse direction (TD). Tensile and impact tests were used to characterize the mechanical properties of the specimens. The microstructural characterization and the fractography of the alloys were carried out by FE-SEM. The obtained results showed that the fracture strain and the impact energy in the TD were 30-50% lower than the LD. The fracture was accelerated by the δ-phase, leading to the reduction of impact energy in the longitudinal and the lateral directions up to 50%. The low-carbon alloy indicated similar characteristics in both the LD and the TD. Aligned carbides changed the fracture path from a zigzag path in the LD to a fibrous path in the TD, while the δ-phase created a flat fracture path. The shear lip area ratio in the tensile fracture cross section was decreased by reducing ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructures and Mechanical Properties of Inconel 718 Alloy at Ultralow Temperatures

The microstructures and mechanical properties of powder metallurgy Inconel 718 alloy were investigated in the temperatures range between 25 and − 253 °C. Tensile strength increased with the decrease in temperature, while the ductility first increased and then decreased. There was no significant change in impact toughness. When the temperature was − 253 °C, a zigzag stress–strain curve was observed for the alloy, owing to the interaction of dislocation glide and twinning, which effectively maintained the relatively good ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Mechanical Properties of Stainless Steel/Brass Joints Brazed by Sn-Electroplated Ag Brazing Filler Metals

To develop a high-Sn-content AgCuZnSn brazing filler metal, the BAg50CuZn was used as the base filler metal and a Sn layer was electroplated upon it. Then, the 304 stainless steel and the H62 brass were induction-brazed with the Sn-plated brazing filler metals. The microstructures of the joints were examined with an optical microscope, a scanning electron microscope and an x-ray diffractometer. The corresponding mechanical properties were obtained with a universal tensile testing machine. The results indicated that the induction brazed joints consisted of the Ag phase, the Cu phase and the CuZn phase. When the content of Sn in the Sn-plated Ag brazing filler metal was 6.0 or 7.2 wt.%, the Cu{sub 5}Zn{sub 8}, the Cu{sub 41}Sn{sub 11} and the Ag{sub 3}Sn phases appeared in the brazed joint. The tensile strength of the joints brazed with the Sn-plated filler metal was higher compared to the joints with the base filler metal. When the content of Sn was 6.0 wt.%, the highest tensile strength of the joint reached to 395 MPa. The joint fractures presented a brittle mode, mixed with a low amount of ductile fracture, when the content of Sn exceeded 6.0 wt.%.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Effect of Prestrain Temperature on Kinetics of Static Recrystallization, Microstructure Evolution, and Mechanical Properties of Low Carbon Steel

In this research, the samples of a low carbon steel sheet were rolled up to a thickness prestrain of 67% at three different temperatures consisted of room, blue brittleness, and subzero temperature. Microhardness, SEM, and tensile tests were carried out to evaluate the static recrystallization kinetics defined by the Avrami equation, microstructural evolution, and mechanical properties. It was found that the Avrami exponent is altered with change in prestrain temperature and it achieves the value of 1 to 1. 5. Moreover, it was indicated that prestraining at subzero temperature followed by annealing at 600 °C leads to considerable enhancement in tensile properties and kinetics of static recrystallization compared to room and blue brittleness temperatures. The prestraining at blue brittleness temperature followed by annealing treatment caused, however, a higher strength and faster kinetics compared with that at room temperature. It was concluded that although from the steel ductility point of view, the blue brittleness temperature is called an unsuitable temperature, but it can be used as prestraining temperature to develop noticeable combination of strength and ductility in low carbon steel.

36 MATERIALS SCIENCE↗