Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

A short pulse of mechanical force induces gene expression and growth in MC3T3-E1 osteoblasts via an ERK 1/2 pathway

Physiological mechanical loading is crucial for maintenance of bone integrity and architecture. We have calculated the strain caused by gravity stress on osteoblasts and found that 4-30g corresponds to physiological levels of 40-300 microstrain. Short-term gravity loading (15 minutes) induced a 15-fold increase in expression of growth-related immediate early gene c-fos, a 5-fold increase in egr-1, and a 3-fold increase in autocrine bFGF. The non-growth-related genes EP-1, TGF-beta, and 18s were unaffected by gravity loading. Short-term physiological loading induced extracellular signal-regulated kinase (ERK 1/2) phosphorylation in a dose-dependent manner with maximum phosphorylation saturating at mechanical loading levels of 12g (p < 0.001) with no effect on total ERK. The phosphorylation of focal adhesion kinase (FAK) was unaffected by mechanical force. g-Loading did not activate P38 MAPK or c-jun N-terminal kinase (JNK). Additionally, a gravity pulse resulted in the localization of phosphorylated ERK 1/2 to the nucleus; this did not occur in unloaded cells. The induction of c-fos was inhibited 74% by the MEK1/2 inhibitor U0126 (p < 0.001) but was not affected by MEK1 or p38 MAPK-specific inhibitors. The long-term consequence of a single 15-minute gravity pulse was a 64% increase in cell growth (p < 0.001). U0126 significantly inhibited gravity-induced growth by 50% (p < 0.001). These studies suggest that short periods of physiological mechanical stress induce immediate early gene expression and growth in MC3T3-E1 osteoblasts primarily through an ERK 1/2-mediated pathway.

NASA Discipline Cell Biology↗
NASA NTRS1995

Calculation of design load for the MOD-5A 7.3 mW wind turbine system

Design loads are presented for the General Electric MOD-SA wind turbine. The MOD-SA system consists of a 400 ft. diameter, upwind, two-bladed, teetered rotor connected to a 7.3 mW variable-speed generator. Fatigue loads are specified in the form of histograms for the 30 year life of the machine, while limit (or maximum) loads have been derived from transient dynamic analysis at critical operating conditions. Loads prediction was accomplished using state of the art aeroelastic analyses developed at General Electric. Features of the primary predictive tool - the Transient Rotor Analysis Code (TRAC) are described in the paper. Key to the load predictions are the following wind models: (1) yearly mean wind distribution; (2) mean wind variations during operation; (3) number of start/shutdown cycles; (4) spatially large gusts; and (5) spatially small gusts (local turbulence). The methods used to develop statistical distributions from load calculations represent an extension of procedures used in past wind programs and are believed to be a significant contribution to Wind Turbine Generator analysis. Test/theory correlations are presented to demonstrate code load predictive capability and to support the wind models used in the analysis. In addition MOD-5A loads are compared with those of existing machines. The MOD-5A design was performed by the General Electric Company, Advanced Energy Program Department, under Contract DEN3-153 with NASA Lewis Research Center and sponsored by the Department of Energy.

Mirandy, L.↗
DOE OSTI2026

Propagation of elastic waves in a flexomagnetic solid

Flexomagnetism is the coupling between magnetism and strain gradients and is a technologically relevant phenomenon. We present a theory of elastic wave propagation in a linear elastic flexomagnetic material with microstructure and strain gradient elastic interactions. The expressions of frequency, phase velocity, and group velocity of longitudinal and transverse waves are derived and are shown to depend on the flexomagnetic coefficient and microstructure. We also show that the effect of flexomagnetism and microstructure can lead to some interesting phenomena in wave propagation, which are not observed in classical linear elasticity theory of waves. Specifically, in contrast to classical linear elastic materials, where wave propagation is non-dispersive, flexomagnetic materials with microstructure can exhibit both normal and abnormal dispersion. It is also noteworthy that, in flexomagnetic materials with gradient elasticity, the phase velocities of transverse waves can exceed those of longitudinal waves, which is atypical in classical elasticity. Furthermore, waves can also attenuate for a certain range of wavenumbers that depend on the flexomagnetic coefficient and microstructural parameters. Finally, we explore the possibility of waves exhibiting zero group velocity modes, where waves are non-propagating but have strong local energy confinement, negative group velocity modes, where the wave packet moves in the opposite direction to that of wave propagation, and the phenomenon of wave freezing, where a propagating wave stops in space without diffusing or spreading.

Ghosh, Swarnava [ORNL] (ORCID:0000000338005264)↗
DOE OSTI2025

How Thermodynamic, Electronic, and Steric Factors Influence Mesitylcopper Oligomers

Mesitylcopper (CuMes) is a highly versatile organocopper reagent used in both organic and inorganic syntheses. It has previously been shown that CuMes exists as a tetrameric or pentameric cyclic oligomer [CuMes] n (n = 4, 5), both in solution and in the solid state. The bonding arrangement between the [CuMes] units has qualitatively been described as localized three-center twoelectron (3c-2e) bonds. However, the electronic, structural, and thermodynamic forces driving this aggregation are still not well understood. For this reason, we employed density functional theory (DFT) calculations to study mesitylcopper as a monomeric [CuMes] unit and [CuMes]n oligomers with n = 2 to n = 7. We found that there is a strong electronic driving force for aggregation caused by strong mixing between the Cu’s d orbitals and Mes’s π orbitals in oligomers larger than the dimer. This mixing is only optimized in oligomers with n ≥ 3, where the mesityl group is no longer bonded to a single copper center but instead becomes a bridging ligand. Beyond the trimer, steric and entropic factors become relevant for determining the relative stabilities of the different aggregates, with midsized oligomers (n = 4−5) having the optimal balance between the electronic Cu−C bonding character, Cu···Cu attractive forces, entropy, reduced internal ring strain, and reduced steric interactions between the mesityl groups.

Copper↗
NASA NTRS1992

Does the sedimentology of the Chelmsford formation provide evidence for a meteorite impact origin of the Sudbury structure?

The post-'event' fill of the Paleoproterozoic Sudbury Basin consists of at least 600 m of deep-water mudrocks of the Onwatin Formation, overlain by 850 m of lithic-arkosic muddy sandstones in the Chelmsford Formation. While mudstones of the Onwatin reflect deposition in a deep-water, anoxic setting, there is no clear evidence of local breccias, conglomerates, or sand bodies to support the concept that the basin was protected by the steep walls of an impact crater. Carbonates in the basal, Vermillion Member are of sedimentary exhalitive origin and were not derived from a shallow marine shelf. Turbidites in the Chelmsford Formation show no evidence of centripetal fill as might be expected from a restricted, circular basin. They appear to have been emplaced by predominantly southwesterly flowing turbidity currents, which showed little to no deflection along the depositional axis of an elongate foreland basin that developed in front of the rising Penokean mountain chain. While the presence of minor sandstone-filled fractures in parts of the Chelmsford Formation suggests the presence of north- or south-directed paleoslopes, no evidence is seen to support the existence of subbasins or a central uplift within the Sudbury Basin. While tilt-corrected paleocurrent orientations are ambiguous, due to postdepositional shortening of strata during cleavage development, strain correction of the observations makes little difference to the net, south-southwest-directed paleoflow.

Long, D. G. F.↗
NASA NTRS1981

A proposal to conduct a Caribbean plate project involving the application of space technology to the study of Caribbean geology

The Caribbean plate project is designed to improve current understanding of geological resources and geological hazards within the Caribbean region. Models of mineral occurrence and genesis (including energy resources) on a regional scale, which contribute to nonrenewable resource investigations. Models of lithospheric stress and strain on a regional scale, which contribute to forecasting geological hazards such as earthquakes and major volcanic eruptions are developed. Geological information is synthesize, and research tools provided by space technology the study of the Earth's crust are used. The project was organized in a thematic fashion, to focus on specific geological aspects of the Caribbean plate which are considered to be key factors in developing the types of models described. The project adopts a synoptic perspective in seeking to characterize the three dimensional structure, composition, state of stress, and evolution of the entire Caribbean plate. Geological information derived from analysis of space acquired data is combined with information provided by conventional methods to obtain insight into the structure, composition, and evolution of the Earth's crust. In addition, very long baseline interferometry and laser ranging techniques, which are also based upon the use of space technology, obtain information concerning crustal motion that, in turn, provides insight into the distribution and localization of crustal stress.

Wadge, G.↗
DOE OSTI2020

First-principles study of hydrogen behavior near W/WC interfaces

Hydrogen (H) solution, migration, and binding to vacancies near the tungsten/tungsten carbide (W/WC) interfaces based on hcp WC or bcc W (W/WCb and Wb/WC) have been studied by first-principles simulations to provide insights into the effect of C on H behavior in W exposed to C deposition in fusion reactors. The H behavior near the W/WC interfaces is related to the tensile or compressive strain due to the lattice match and interfacial effects. Near the W/WCb interface, the H solution energy in hcp WC increases approaching the interface, while it decreases from the W side to the interface. The configuration change of the W slab significantly decreases the H solution energy but has only a modest effect on the H migration energy barrier in comparison with the values in bcc W. The interface enhances the H binding to vacancies in WC layers. Both the interface and configuration adjustment of the W slab reduce the H binding to vacancies on the W side of the interface. Near the Wb/WC interface, H solution energies in both WC and W slabs weakly decrease approaching the interface. The configuration change of the WC slab significantly increases the H solution energy and binding energy to vacancies but decreases the H migration energy barrier in comparison with the values in hcp WC. The H energetics near the W/WC interfaces indicate the likelihood of H localization and diffusion in the W side of the interface, rather than diffusing through the interface into WC layers.

Yang, L. (ORCID:0000000322166071)↗
NASA NTRS2008

Deconvoluting the Friction Stir Weld Process for Optimizing Welds

In the friction stir welding process, the rotating surfaces of the pin and shoulder contact the weld metal and force a rotational flow within the weld metal. Heat, generated by the metal deformation as well as frictional slippage with the contact surface, softens the metal and makes it easier to deform. As in any thermo-mechanical processing of metal, the flow conditions are critical to the quality of the weld. For example, extrusion of metal from under the shoulder of an excessively hot weld may relax local pressure and result in wormhole defects. The trace of the weld joint in the wake of the weld may vary geometrically depending upon the flow streamlines around the tool with some geometry more vulnerable to loss of strength from joint contamination than others. The material flow path around the tool cannot be seen in real time during the weld. By using analytical "tools" based upon the principles of mathematics and physics, a weld model can be created to compute features that can be observed. By comparing the computed observations with actual data, the weld model can be validated or adjusted to get better agreement. Inputs to the model to predict weld structures and properties include: hot working properties ofthe metal, pin tool geometry, travel rate, rotation and plunge force. Since metals record their prior hot working history, the hot working conditions imparted during FSW can be quantified by interpreting the final microstructure. Variations in texture and grain size result from variations in the strain accommodated at a given strain rate and temperature. Microstructural data from a variety of FSWs has been correlated with prior marker studies to contribute to our understanding of the FSW process. Once this stage is reached, the weld modeling process can save significant development costs by reducing costly trial-and-error approaches to obtaining quality welds.

Schneider, Judy↗
DOE OSTI2024

Cryogenic aspects of a 20 MW class low-temperature superconducting generator for the renewables industry

In this paper we give a progress update on the cryogenic design for cooling a 20 MW class, partially superconducting generator with stationary field coils for offshore wind renewables industry [1-2]. This is a continuation of an earlier program on a 10 MW system dating back ten years. Whereas this new power rating increase leads to a radial diameter expansion of the superconducting field coils from 4 to > 9.5 m, it maintains the axial length. We show the design based on this scaled up with enlarged diameter. The field coil size increase asks for higher cooling power that leads to a bigger cold box size to accommodate the cryocoolers. In the design, as many as 8 cryocoolers can be accessed and serviced from the nacelle that houses the main cryogenic components. A typical thermal load balance sheet with all components is given and compared against the available cryocooler cooling power at different operating conditions. Due to the cryocoolers’ local point of contact cooling within the nacelle, the temperature gradient of the thermal shield that fully encloses the cold mass with its embedded field coils needs to be balanced out to minimize the heat burden on the field coils. This requires additional analytical efforts and implementation of further design features. The extended nacelle houses the cold box with its cryogenic infrastructure. The interface for the envisaged cryogenic pushbutton closed-loop circulating system remains invisible, requires no handling of cryogenic liquids and is hermetically closed. The field coil diameter increase also leads to a greater initial helium gas storage volume. In addition, it requires higher initial room temperature fill pressure within the toroidal helium vapor storage tanks and in cooling tubes connecting to the cryocoolers. The toroidal helium gas tanks are thermally coupled with the thermal shield so that helium convection inside the storage tank can improve heat transfer and reduce the temperature gradient of the thermal shield. Besides those heat transfer challenges, additional mechanical strain within this large structure is exerted on the torque tubes during initial cooldown and when energizing field coils. Some of those design challenges are quite unexpected, leading to novel workarounds in order to maintain the chosen cooling strategy. Finally, we assess those design limitations in view of further cryogenic scalability with emphasis on manufacturability and assembly.

cryogenics↗
NASA NTRS1999

A Method for Calculating Strain Energy Release Rates in Preliminary Design of Composite Skin/Stringer Debonding Under Multi-Axial Loading

Three simple procedures were developed to determine strain energy release rates, G, in composite skin/stringer specimens for various combinations of unaxial and biaxial (in-plane/out-of-plane) loading conditions. These procedures may be used for parametric design studies in such a way that only a few finite element computations will be necessary for a study of many load combinations. The results were compared with mixed mode strain energy release rates calculated directly from nonlinear two-dimensional plane-strain finite element analyses using the virtual crack closure technique. The first procedure involved solving three unknown parameters needed to determine the energy release rates. Good agreement was obtained when the external loads were used in the expression derived. This superposition technique was only applicable if the structure exhibits a linear load/deflection behavior. Consequently, a second technique was derived which was applicable in the case of nonlinear load/deformation behavior. The technique involved calculating six unknown parameters from a set of six simultaneous linear equations with data from six nonlinear analyses to determine the energy release rates. This procedure was not time efficient, and hence, less appealing. A third procedure was developed to calculate mixed mode energy release rates as a function of delamination lengths. This procedure required only one nonlinear finite element analysis of the specimen with a single delamination length to obtain a reference solution for the energy release rates and the scale factors. The delamination was extended in three separate linear models of the local area in the vicinity of the delamination subjected to unit loads to obtain the distribution of G with delamination lengths. This set of sub-problems was Although additional modeling effort is required to create the sub- models, this local technique is efficient for parametric studies.

Krueger, Ronald↗
NASA NTRS1961

A Study of the Free Oscillations of the Earth

Published observations on the toroidal oscillations of the earth are critically reviewed. A supplementary analysis of the record obtained by the Lamont strain seismometer is presented. Eleven toroidal modes are identified, and it is concluded that the periods are known to within 1 per cent. A perturbation scheme involving the ratio of the angular velocity of the earth to the resonant frequency is used in calculating the effects due to the rotation of the earth on the resonant frequency. The free oscillations are viewed as a superposition of traveling waves. In a nonrotating system two traveling waves combine to produce a stationary standing wave. In a rotating system, the rotation distinguishes between waves that travel in the direction of rotation and those that travel in the opposite direction. Rotation removes a degeneracy and results in a splitting of a spectral peak of order l into 2 times l plus 1 peaks. The fractional displacement in frequency for the lowest-order toroidal oscillations is 1/206 and of the same order as the Q of the peak, so that splitting will probably not be observed in the toroidal oscillations. Viewed locally, rotation causes a particle to precess about a direction parallel to the axis of rotation. This precession will cause a variation of amplitude with time if the motion is recorded by an instrument with an anisotropic response function. Care is therefore needed in studying the time decay of a given spectral peak. Rotation also couples the normal coordinates so that a motion that is initially purely horizontal will develop a vertical component. It is expected that vertical seismometers should record particle motion with the toroidal frequencies. The perturbations of the toroidal oscillations due to core-mantle interaction are treated in detail. An exact expression is obtained for the rate of energy dissipated by a finitely conducting plate oscillating across a magnetic field. The energy dissipated at the core-mantle boundary due to viscous and hydromagnetic coupling is shown to be insignificant as compared with the energy dissipated within the mantle. The toroidal magnetic field leaking into the lower mantle combines with the dipole field, resulting in a stress on the mantle, tending to stiffen the lower boundary. The stress is of sufficient magnitude to produce a displacement toward higher frequency in the lower-order toroidal oscillations. Observations on the (sub 0) T (sub 2) oscillations lead to an estimate of the toroidal magnetic field in the lower mantle. A calculation of elastic energy in the low-order oscillations suggests a value of 10 (sup 18) ergs per cycles per hour for the energy density at low frequencies in the Chilean earthquake. Each mode of oscillation has a characteristic radial distribution of elastic energy associated with it. This distribution determines which parts of the earth contribute most heavily in determining a particular resonant frequency. The distribution of energy for the lower 17 modes for a homogeneous and a Gutenberg model earth is calculated. The resonant frequencies for models of the earth based on the Gutenberg and Lehmann distribution of elastic properties are presented. It is shown that the Gutenberg model earth fits the observations more closely than the Lehmann model and that a slight alteration of the Gutenberg model gives a significantly better fit to the observations. The alteration involves a lower shear-wave velocity in the lower mantle while the Gutenberg velocity distribution is maintained in the upper mantle. Various studies of the earth's oscillations coupled with surface-wave investigations substantiate Gutenberg's hypothesis of a layer of low velocity in the upper mantle. The physical conditions required for the formation of a region of low velocity are examined in detail. The results confirm Birch's earlier statement that a temperature gradient in excess of 6 degrees to 7 degrees per kilometer is needed to produce a decrease in velocity. The low-velocity layer does not require that the temperature approach or exceed the melting temperature. If tile upper mantle is homogeneous, the region of lower velocity should commence at the base of the crust and extend to 150 kilometers under the oceans and about 100 kilometers under continental regions. The distribution of thermal conductivity and radioactivity consistent with the low-velocity layer is also considered.

MacDonald, Gordon J. F.↗
DOE OSTI2024

Impact of LWR assembly structural features on cladding burst behavior under LOCA conditions

This provides an initial scoping study on clad balloon and burst behavior for burnup extension of reactor fuel. The associated issues with burnup extension are fuel fragmentation, relocation, and dispersal in the event of cladding failure. The general finding of this work is that the structural features, spacer grids and mixing vanes, locally suppress cladding deformation but have little impact on the overall clad performance during loss-of-coolant accidents. The work detailed in a previous report by Capps et al. focused on core optimization via neutronics, thermal hydraulics and thermomechanical analysis for burnups beyond 62 GWD/tU and enrichments above 5%. Uncertainty of fuel fragmentation relocation and dispersal in high-burnup rods during accident conditions was also investigated. The dispersal aspect of fuel fragmentation depends on cladding rupture. Thus, assessing uncertainties in the rupture behavior is helpful in estimating the dispersal of high-burnup fuel. This study builds on the previous work by assessing the impact of assembly structural features on cladding balloon and burst behavior in a full-length fuel rod. In this work, the BISON fuel performance code was used to generate 2D radial and height meshes containing structural features commonly used in nuclear fuel assemblies. First, meshes were generated with spacer grids. Results were then compared to the cladding burst temperature and balloon strain results from the previous work. A mesh sensitivity study was performed to ensure that mixing vanes and spacer grid effects were appropriately considered, resulting in a more refined mesh than the previous study. The balloon deformation and burst times of the cladding were compared to the original case. Consideration was also given to the effect of rod initial pressure. In conclusion, 3D quarter rod simulations were also performed and found good agreement with the 2D simulations in clad deformation and reasonable agreement in burst times.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Enhanced two-dimensional ferromagnetism in van der Waals β-UTe 3 monolayers

The discovery of local-moment magnetism in van der Waals (vdW) semiconductors down to the single-layer limit has led to a paradigm shift in the understanding of two-dimensional (2D) magnets. The incorporation of strong electronic and magnetic correlations in 2D vdW metals remains a sought-after platform to enable control of emergent quantum phases and to achieve more theoretically tractable microscopic models of complex materials. To date, however, there is limited success in the discovery of such metallic vdW platforms, and f-electron monolayers remain out of reach. Here, we demonstrate that strongly correlated β–uranium tritelluride (β-UTe 3 ) can be exfoliated to the monolayer limit. Unexpectedly, β-UTe 3 remains ferromagnetic in this limit with an enhanced ordering temperature of 35 kelvin, a factor of two larger than its bulk counterpart. Our work establishes β-UTe 3 as a materials platform for investigating and modeling correlated behavior in the monolayer limit and opens numerous avenues for quantum control with, e.g., strain engineering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2017

Modulation of Bone Marrow Primary Cell Osteoblastogenesis and Cell Senescence by Mechanical Stimulation

Cell and animal studies conducted onboard the International Space Station and formerly the Shuttle flights have provided groundbreaking data illuminating the deleterious biological response of bone to mechanical unloading. Specifically CDKN1A/p-21 a cell senescence protein, was found to be upregulated in osteoprecursor cells of the femur during 15-day spaceflight, leading to the working hypothesis that CDKN1A/p-21 plays a role in inhibition of bone formation via mechanical regulation. To evaluate this hypothesis, utilizing a p-21 knockout mouse-line and relevant wildtype control, we cultured femoral bone marrow primary cells under unloaded (static) and cyclically stretched loading through a 30 day osteoblastogenesis protocol. Morphologic evaluation of the cultures demonstrated that mechanical stretching aligned the cells and increased the presence of defined focal adhesion expressing talin, integrin αvβ3, and PTK2 protein tyrosine kinase 2, also known as focal adhesion kinase (FAK) in both mouse strains. In corroboration with previous investigations of cell survival signals relation to FAK, our study found that with greater concentration of focal adhesions via stretch stimulation the live cell percentage was significantly higher than the unloaded controls (p-21 knockout line: +49.70%, p*=0.009, wildtype control: +18.14%, p*=.01). Also evaluated was the mineralization and ECM secretion capability of the differentiating cells. Von Kossa staining has shown that in the p-21 knockout cells unloaded cells produce more matrix that the stretch stimulated, however the matrix is unorganized presenting in sporadic nodules covering approximately 30% of the culture area at day 14 (n=6 wells) while the stretch stimulated cultures have less mineralization content the surface area containing mineralized matrix is greater (~68% at day 14). Q-PCR evaluation of the p-21 knockout cells revealed that canonical (β-catenin cascade) and non-canonical wnt11 and downstream planar cell polarity (wnt/PCP) pathway molecule RAC1 are prevalently upregulated with mechanical stimulation. Immunofluorescence for β-catenin and RAC1 showed co-localization at the nuclear membrane of the p-21 knockout cells but not the wildtype (n=1) suggesting that molecular communication via the canonical and wnt/PCP pathway are initiated by mechanical loading and experience regulation along the signaling cascade by CDKN1A/p-21. Future investigations will further elucidate this relationship and provide causal data demonstrating mechanical loading’s modulatory effect on p-21 expression change.

Juran, Cassandra M.↗
NASA NTRS2011

Approaches for Tensile Testing of Braided Composites

For angleply composites, lamina tension and compression strengths are commonly determined by applying classical lamination theory to test data obtained from testing of angleply composite specimens. For textile composites such as 2D triaxial braids, analysis is more complex and standard test methods do not always yield reliable strength measurements. This paper describes recent research focused on development of more reliable tensile test methods for braided composites and presents preliminary data for various approaches. The materials investigated in this work have 0deg+/-60 2D triaxial braid architecture with nearly equal fiber volume fraction in each of the three fiber directions. Flat composite panels are fabricated by resin transfer molding (RTM) using six layers of the braided preform aligned along the 0deg fiber direction. Various epoxy resins are used as matrix materials. Single layer panels are also fabricated in order to examine local variations in deformation related to the braid architecture. Specimens are cut from these panels in the shape of standard straight-sided coupons, an alternative bowtie geometry, and an alternative notched geometry. Axial tensile properties are measured using specimens loaded along the 0deg fiber direction. Transverse tensile properties are measured using specimens loaded perpendicular to the 0deg fibers. Composite tubes are also fabricated by RTM. These tubes are tested by internal pressurization using a soft rubbery material sealed between the inside diameter of the tube and the load fixtures. The ends of the tube are unconstrained, so the primary load is in the hoop direction. Tubes are fabricated with the 0deg fibers aligned along the tube axis by overbraiding the preform on a mandrel. Since the loading is in the hoop direction, testing of the overbraided tube provides a measure of transverse tensile strength. Previous work has indicated that straight-sided coupons yield a transverse tensile strength that is much lower than the expected material strength because of premature edge-initiated failure. Full-field strain measured during transverse tensile tests clearly showed accumulation of edge damage prior to failure. In the current work, high speed video and testing of single layer specimens are used to investigate potential failure mechanisms in more detail. High speed video clearly shows the edge initiation in six layer transverse tensile test coupons. Specimens with the bowtie geometry and the notched geometry minimize this edge effect and yield significantly higher transverse tensile strength values compared to the straight-sided coupons. However, bowtie and notched specimens geometries are not ideal because of the non-uniform stress and strain fields in the region of failure. Testing of tubes using internal pressurization eliminates edge-initiated failure and provides a more uniform state of stress and strain. Preliminary results indicate that bowtie, notched, and tube specimens yield comparable values for transverse tensile strength and that these values are much higher than the strength measured using a straight-sided coupon.

Roberts, Gary D.↗
NASA NTRS2011

Impact of Material and Architecture Model Parameters on the Failure of Woven Ceramic Matrix Composites (CMCs) via the Multiscale Generalized Method of Cells

It is well known that failure of a material is a locally driven event. In the case of ceramic matrix composites (CMCs), significant variations in the microstructure of the composite exist and their significance on both deformation and life response need to be assessed. Examples of these variations include changes in the fiber tow shape, tow shifting/nesting and voids within and between tows. In the present work, the effects of many of these architectural parameters and material scatter of woven ceramic composite properties at the macroscale (woven RUC) will be studied to assess their sensitivity. The recently developed Multiscale Generalized Method of Cells methodology is used to determine the overall deformation response, proportional elastic limit (first matrix cracking), and failure under tensile loading conditions. The macroscale responses investigated illustrate the effect of architectural and material parameters on a single RUC representing a five harness satin weave fabric. Results shows that the most critical architectural parameter is weave void shape and content with other parameters being less in severity. Variation of the matrix material properties was also studied to illustrate the influence of the material variability on the overall features of the composite stress-strain response.

Liu, Kuang C.↗
DOE OSTI2021

Prebiotic properties of Bacillus coagulans MA-13: production of galactoside hydrolyzing enzymes and characterization of the transglycosylation properties of a GH42 β-galactosidase

The spore-forming lactic acid bacterium Bacillus coagulans MA-13 has been isolated from canned beans manufacturing and successfully employed for the sustainable production of lactic acid from lignocellulosic biomass. Among lactic acid bacteria, B. coagulans strains are generally recognized as safe (GRAS) for human consumption. Low-cost microbial production of industrially valuable products such as lactic acid and various enzymes devoted to the hydrolysis of oligosaccharides and lactose, is of great importance to the food industry. Specifically, α- and β-galactosidases are attractive for their ability to hydrolyze not-digestible galactosides present in the food matrix as well as in the human gastrointestinal tract. In this work we have explored the potential of B. coagulans MA-13 as a source of metabolites and enzymes to improve the digestibility and the nutritional value of food. A combination of mass spectrometry analysis with conventional biochemical approaches has been employed to unveil the intra- and extra- cellular glycosyl hydrolase (GH) repertoire of B. coagulans MA-13 under diverse growth conditions. The highest enzymatic activity was detected on β-1,4 and α-1,6-glycosidic linkages and the enzymes responsible for these activities were unambiguously identified as β-galactosidase (GH42) and α-galactosidase (GH36), respectively. Whilst the former has been found only in the cytosol, the latter is localized also extracellularly. The export of this enzyme may occur through a not yet identified secretion mechanism, since a typical signal peptide is missing in the α-galactosidase sequence. A full biochemical characterization of the recombinant β-galactosidase has been carried out and the ability of this enzyme to perform homo- and hetero-condensation reactions to produce galacto-oligosaccharides, has been demonstrated. Probiotics which are safe for human use and are capable of producing high levels of both α-galactosidase and β-galactosidase are of great importance to the food industry. In this work we have proven the ability of B. coagulans MA-13 to over-produce these two enzymes thus paving the way for its potential use in treatment of gastrointestinal diseases.

59 BASIC BIOLOGICAL SCIENCES↗