SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

All sources NASA NTRS DOE OSTI

NASA NTRS1996

Characterization of SiC Fiber (SCS-6) Reinforced-Reaction-Formed Silicon Carbide Matrix Composites

Silicon carbide fiber (SCS-6) reinforced-reaction-formed silicon carbide matrix composites were fabricated using a reaction-forming process. Silicon-2 at.% niobium alloy was used as an infiltrant instead of pure silicon to reduce the amount of free silicon in the matrix after reaction forming. The matrix primarily consists of silicon carbide with a bimodal grain size distribution. Minority phases dispersed within the matrix are niobium disilicide (NbSi2), carbon, and silicon. Fiber pushout tests on these composites determined a debond stress of approximately 67 MPa and a frictional stress of approximately 60 MPa. A typical four-point flexural strength of the composite is 297 MPa (43.1 KSi). This composite shows tough behavior through fiber pullout.

Singh, M.↗

DOE OSTI2026

Effects of cleavable comonomer structure and crosslinker chemistry on the performance and deconstructability of frontally cured pDCPD composites

Reclaiming undamaged carbon fiber from thermoset composites requires chemical recycling methods that leverage complete deconstruction of the polymer matrix. Cleavable comonomers enable chemical recycling of poly(dicyclopentadiene) (pDCPD) composites, but current systems suffer from reduced glass transition temperature (T g ), limiting application. Here, we investigate the effect of cleavable comonomer loading and cleavable crosslinker chemistry on network formation, thermomechanical properties, and fiber recovery in frontally cured pDCPD composites. All formulations fully deconstructed in acid and recovered fibers ranged from pristine to variably contaminated depending on crosslinker chemistry. Reducing backbone-cleaving comonomer content and introducing cleavable crosslinkers raised composite T g to 126–138 °C compared to 105 °C previously reported in deconstructable pDCPD composites. Although the cleavable crosslinkers increased T g in unreinforced polymers to 150–160 °C, the fiber-reinforced composite T g remained lower due to under-curing and interactions between the crosslinkers and the fiber surface. Increasing polymerization initiator loading improved comonomer conversion and yielded a deconstructable composite with T g = 151 °C, approaching the performance of non-deconstructable pDCPD composites (T g = 161 °C). This work clarifies how cleavable comonomer and crosslinker chemistry governs curing, thermomechanical performance, and reclaimed reinforcement quality, and the results highlight the need for more robust cleavable comonomers to realize multigenerational composite materials without sacrificing thermomechanical performance.

Carbon fibers↗

NASA NTRS1981

Modulus, strength and thermal exposure studies of FP-Al2O3/aluminum and FP-Al2O3/magnesium composites

The mechanical properties of FP-Al2O3 fiber reinforced composites prepared by liquid infiltration techniques are improved. A strengthening addition, magnesium, was incorporated with the aluminum-lithium matrix alloy usually selected for these composites because of its good wetting characteristics. This ternary composite, FP-Al2O3/Al-(2-3)Li-(3-5)Mg, showed improved transverse strength compared with FP-Al2O3/Al-(2-3)Li composites. The lower axial strengths found for the FP-Al2O3/Al-(2-3)Li-(3-5)Mg composites were attributed to fabrication related defects. Another technique was the use of Ti/B coated FP-Al2O3 fibers in the composites. This coating is readily wet by molten aluminum and permitted the use of more conventional aluminum alloys in the composites. However, the anticipated improvements in the axial and transverse strengths were not obtained due to poor bonding between the fiber coating and the matrix. A third approach studied to improve the strengths of FP-Al2O3 reinforced composites was the use of magnesium alloys as matrix materials. While these alloys wet fibers satisfactorily, the result indicated that the magnesium alloy composites used offered no axial strength or modulus advantage over FP-Al2O3/Al-(2-3)Li composites.

Bhatt, R. T.↗

NASA NTRS1991

Effective thermal conductivity of composites with fibre-matrix debonding

Debonding of the fiber-matrix interface is a major cause for the degradation of the mechanical properties and the loss of thermal conductivity of fiber-reinforced composites. This paper discusses two analytical approaches for modeling the thermal conduction problem of composites. One is based on the concept of modeling the thermal barrier by an equivalent heat transfer coefficient at the fiber-matrix interface, as described by Hasselman and Johnson (1987) and Benveniste and Miloh (1986). The other approach, suggested by Hatta and Taya (1986), is by treating a composite with debonded interface as a coated-fiber composite. The major advantage of the latter aproach is that the thickness of the fiber coating can be realistically modeled depending upon the extent of degradation of the composite with the thermal conductivity of the coating as that of air.

Fadale, T. D.↗

DOE OSTI2023

Review on Hybrid Reinforced Polymer Matrix Composites with Nanocellulose, Nanomaterials, and Other Fibers

The use of composite materials has seen many new innovations for a large variety of applications. The area of reinforcement in composites is also rapidly evolving with many new discoveries, including the use of hybrid fibers, sustainable materials, and nanocellulose. In this review, studies on hybrid fiber reinforcement, the use of nanocellulose, the use of nanocellulose in hybrid forms, the use of nanocellulose with other nanomaterials, the applications of these materials, and finally, the challenges and opportunities (including safety issues) of their use are thoroughly discussed. This review will point out new prospects for the composite materials world, enabling the use of nano- and micron-sized materials together and creating value-added products at the industrial scale. Furthermore, the use of hybrid structures consisting of two different nano-materials creates many novel solutions for applications in electronics and sensors.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Fiber Orientation Evaluation in Reinforced Composites using Digital Image Correlation

This paper presents an innovative nondestructive evaluation (NDE) approach to evaluate fiber orientation in fiber reinforced composites utilizing digital image correlation (DIC). Fiber orientation is a crucial factor that influences the mechanical and thermal properties of the composite. Conventional methods for fiber orientation evaluation and measurement are either destructive, which are typically laborious. NDE methods such as micro computed tomography are expensive and limited in sample size. In this work, we evaluate two methods of excitation of the composite, namely-quasistatic mechanical loading and thermal cycling. Digital Image Correlation (DIC) has been employed in conjunction for fiber orientation measurements. The DIC system is able to measure the fiber orientation by capturing 19x higher strain in the transverse direction of the reinforced fiber axis during excitation. The larger strain occurs in the transverse direction due to larger elongation in the surrounding polymer matrix than the fiber which resists elongation. This innovative method is within the preliminary stage and has been developed to fill the gap/limitations of other NDE methods.

Spencer, Ryan↗

DOE OSTI2022

Highly Recyclable Thermosets for Lightweight Composites: CRADA 517 [Abstract only]

Lightweight composites are of increasing need to enable reduced fuel usage, reduced carbon emissions and increased range in air and ground transportation. The superior weight savings of carbon fiber thermoset composites are impeded by material and production costs and the limited options available for composite repair and recycle. The materials recovery and recycling sector is currently overwhelmed by an abundance of low-value materials and limited market opportunities for downcycled content, rendering landfilling a more attractive alternative. Vitrimers represent a new paradigm for repairable and recyclable thermosets, but this relatively new technology will require development, including government investment, to reduce risks for its adoption by aerospace and automotive OEMs. The overall goal of the project is to create recyclable carbon fiber composites using vitrimer resins that are more energy efficient to produce and have improved properties over baseline technology. The targeted composites will retain their tensile strength after multiple recycling and reprocessing steps. In addition, monomer will be recoverable through depolymerization and re-usable carbon fibers will be retrieved.

36 MATERIALS SCIENCE↗

NASA NTRS2000

Raman Study of Uncoated and P-bn/sic-coated Hi-nicalon Reinforced Celsian Matrix Composites: Residual Stress in the Fibers - Part 2

Band shifts on Raman spectra were used to assess, at a microscopic scale, the residual strain existing in Hi-Nicalon fibers reinforcing celsian matrix composites. Uncoated as well as p-BN/SiC- and p-B(Si)N/SiC-coated Hi-Nicalon fibers were used as the reinforcements. We unambiguously conclude that the fibers are in a state of compressive residual stress. Quantitative determination of the residual stress was made possible by taking into account the heating induced by laser probing and by using a reference line, of fixed wavenumber. We found fiber compressive residual stress values between 110 and 960 MPa depending on the fiber/matrix coating in the composite. A stress relaxation-like phenomenon was observed at the surface of p-BN/SiC-coated Hi-Nicalon fibers whereas the uncoated or p-B(Si)N/SiC-coated Hi-Nicalon fibers did not show any stress relaxation in the Celsian matrix composites.

Gouadec, Gwenael↗

NASA NTRS2000

In-plane and Interlaminar Shear Strength of a Unidirectional Hi-nicalon Fiber-reinforced Celsian Matrix Composite

In-plane and interlaminar shear strength of a unidirectional SiC fiber-reinforced (BaSr)Al2Si2O8 celsian composite were measured by the double-notch shear test method between room temperature and 1200 C. The interlaminar shear strength was lower than the in-plane shear strength at all temperatures. Stress analysis, using finite element modeling, indicated that shear stress concentration was not responsible for the observed difference in strength. Instead, the difference in layer architecture and thus, the favorable alignment of fiber-rich layers with the shear plane in the interlaminar specimens appears to be the reason for the low strength of this composite. A rapid decrease in strength was observed with temperature due to softening of the glassy phase in the material.

Uenal, O.↗

NASA NTRS1985

NASA/aircraft industry standard specification for graphite fiber toughened thermoset resin composite material

A standard specification for a selected class of graphite fiber/toughened thermoset resin matrix material was developed through joint NASA/Aircraft Industry effort. This specification was compiled to provide uniform requirements and tests for qualifying prepreg systems and for acceptance of prepreg batches. The specification applies specifically to a class of composite prepreg consisting of unidirectional graphite fibers impregnated with a toughened thermoset resin that produce laminates with service temperatures from -65 F to 200 F when cured at temperatures below or equal to 350 F. The specified prepreg has a fiber areal weight of 145 g sq m. The specified tests are limited to those required to set minimum standards for the uncured prepreg and cured laminates, and are not intended to provide design allowable properties.

Source record↗

NASA NTRS1989

The interface in tungsten fiber reinforced niobium metal-matrix composites

The creep resistance of tungsten fiber reinforced niobium metal-matrix composites was evaluated. The interface region between the fiber and matrix was characterized by microhardness and electron probe microanalysis measurements which indicated that its properties were between those of fiber and matrix. However, the measured properties of the composite exceeded those calculated by the rule of mixtures even when the interface zone was assumed to retain all the strength of the fiber. The composite structure appeared to enhance the strengths of both the fibers and the matrix above what they exhibited in stand-alone tests. The effect of fiber orientation and matrix alloy composition on the fiber/matrix interface were also evaluated. Small alloying additions of zirconium and tungsten to the niobium matrix affected the creep resistance of the composites only slightly. A decrease in the creep resistance of the composite with increasing zirconium content in the matrix was ascribed to an increase in the diffusion rate of the fiber/matrix interdiffusion reaction, and a slight increase in the creep resistance of the composite was observed with an addition of 9 w percent tungsten to the matrix. In addition, Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis.

Grobstein, Toni L.↗

NASA NTRS2018

Influence of Thin-Film Adhesives in Pullout Tests Between Nickel-Titanium Shape Memory Alloy and Carbon Fiber-Reinforced Polymer Matrix Composites

Strips of nickel-titanium (NiTi) shape memory alloy (SMA) and carbon fiber-reinforced polymer matrix composite (PMC) were bonded together using multiple thin film adhesives and their mechanical strengths were evaluated under pullout test configuration. Tensile and lap shear tests were conducted to confirm the deformation of SMAs at room temperature and to evaluate the adhesive strength between the NiTi strips and the PMC. Optical and scanning electron microscopy techniques were used to examine the interfacial bonding after failure. Simple equations on composite tensile elongation were used to fit the experimental data on tensile properties. ABAQUS models were generated to show the effects of enhanced bond strength and the distribution of stress in SMA and PMC. The results revealed that the addition of thin film adhesives increased the average adhesive strength between SMA and PMC while halting the room temperature shape memory effect within the pullout specimen.

Polymer Matrix Composites↗

NASA NTRS1990

Innovative design of composite structures: The use of curvilinear fiber format to improve buckling resistance of composite plates with central circular holes

The gains in buckling performance are explored that can be achieved by deviating from the conventional straightline fiber format and considering the situation whereby the fiber orientation in a layer, or a group of layers, can vary from point to point. The particular situation studied is a simply supported square plate with a centrally located hole loaded in compression. By using both a sensitivity analysis and a gradient-search technique, fiber orientation in a number of regions of the plate are selected so as to increase the buckling load relative to baseline straightline designs. The sensitivity analysis is used to determine which regions of the plate have the most influence on buckling load, and the gradient search is used to find the design that is believed to represent the absolute maximum buckling load for the conditions prescribed. Convergence studies and sensitivity of the final design are discussed. By examining the stress resultant contours, it is shown how the curvilinear fibers move the load away from the unsupported hole region of the plate to the supported edges, thus increasing the buckling capacity. The tensile capacity of the improved buckling design is investigated, and it is shown that both tensile capacity and buckling capacity can be improved with the curvilinear fiber concept.

Hyer, M. W.↗

NASA NTRS2007

Progressive Fracture of Laminated Composite Stiffened Plate

Laminated fiber-reinforced composite stiffened plate with [0/90/plus or minus 45]s plies made of S-Glass/epoxy are evaluated via computational simulation to study damage and fracture progression. The loads are pressure and temperature which varies from 21 to 65.5 C (case I) and from 143.3 to 21 C (case II). An integrated computer code is used for the simulation of the damage progression. Results show that damage initiation begins at low load level, with matrix cracking at the 0 deg. (bottom and top) plies, fiber fracture at the bottom (0 deg.) ply and interply delamination at the top (0 deg. ) ply. Increasing the applied pressure, the damage growth is expended resulting in fracture through the thickness of the structure. At this stage, 90 percent of the plies damage at applied pressure 15.306 MPa for the case I and 15.036 MPa for the case II. After this stage the cracks propagate rapidly and the structure collapses.

Gotsis, Pascalis K.↗

NASA NTRS1991

A model for the progressive failure of laminated composite structural components

Laminated continuous fiber polymeric composites are capable of sustaining substantial load induced microstructural damage prior to component failure. Because this damage eventually leads to catastrophic failure, it is essential to capture the mechanics of progressive damage in any cogent life prediction model. For the past several years the authors have been developing one solution approach to this problem. In this approach the mechanics of matrix cracking and delamination are accounted for via locally averaged internal variables which account for the kinematics of microcracking. Damage progression is predicted by using phenomenologically based damage evolution laws which depend on the load history. The result is a nonlinear and path dependent constitutive model which has previously been implemented to a finite element computer code for analysis of structural components. Using an appropriate failure model, this algorithm can be used to predict component life. In this paper the model will be utilized to demonstrate the ability to predict the load path dependence of the damage and stresses in plates subjected to fatigue loading.

Allen, D. H.↗

NASA NTRS1978

The prospects for composites based on boron fibers

The fabrication of boron filaments and the production of composite materials consisting of boron filaments and organic or metallic matrices are discussed. Problem involving the use of tungsten substrates in the filament fabrication process, the protection of boron fibers with diffusion barrier cladings, and the application of alloy additives in the matrix to lessen the effects of diffusion are considered. Data on the kinetics of the boron fiber/matrix interaction at high temperatures, and the influence of the fiber/matrix interaction on the mechanical properties of the composite are presented.

Naslain, R.↗

NASA NTRS1991

Mechanical behavior of fiber reinforced SiC/RBSN ceramic matrix composites: Theory and experiment

The mechanical behavior of continuous fiber reinforced SiC/RBSN (Reaction Bonded Silicon Nitride) composites with various fiber contents is evaluated. Both catastrophic and noncatastrophic failures are observed in tensile specimens. Damage and failure mechanisms are identified via in-situ monitoring using NDE (nondestructive evaluation) techniques through the loading history. Effects of fiber/matrix interface debonding (splitting) parallel to fibers are discussed. Statistical failure behavior of fibers is also observed, especially when the interface is weak. Micromechanical models incorporating residual stresses to calculate the critical matrix cracking strength, ultimate strength, and work of pull-out are reviewed and used to predict composite response. For selected test problems, experimental measurements are compared to analytical predictions.

Chulya, Abhisak↗

NASA NTRS1991

Mechanical behavior of fiber reinforced SiC/RBSN ceramic matrix composites - Theory and experiment

The mechanical behavior of continuous fiber reinforced SiC/RBSN (Reaction Bonded Silicon Nitride) composites with various fiber contents is evaluated. Both catastrophic and noncatastrophic failures are observed in tensile specimens. Damage and failure mechanisms are identified via in-situ monitoring using NDE (nondestructive evaluation) techniques throughout the loading history. Effects of fiber/matrix interface debonding (splitting) parallel to fibers are discussed. Statistical failure behavior of fibers is also observed, especially when the interface is weak. Micromechanical models incorproating residual stresses to calculate the critical matrix cracking strength, ultimate strength, and work of pull-out are reviewed and used to predict composite response. For selected test problems, experimental measurements are compared to analytical predictions.

Chulya, Abhisak↗