Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “evaluation process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Evaluation Of A Turbidity Meter For Use At The Defense Waste Processing Facility

Savannah River Remediation’s (SRR’s) Defense Waste Processing Facility (DWPF) Laboratory currently tests for sludge carry-over into the Recycle Collection Tank (RCT) by evaluating the iron concentration in the Slurry Mix Evaporator Condensate Tank (SMECT) and relating this iron concentration to the amount of sludge solids present. A new method was proposed for detecting the amount of sludge in the SMECT that involves the use of an Optek turbidity sensor. Waste Services Laboratory (WSL) personnel conducted testing on two of these units following a test plan developed by Waste Solidification Engineering (WSE). Both Optek units (SN64217 and SN65164) use sensor model AF16-N and signal converter model series C4000. The sensor body of each unit was modified to hold a standard DWPF 12 cc sample vial, also known as a “peanut” vial. The purpose of this testing was to evaluate the use of this model of turbidity sensor, or meter, to provide a measurement of the sludge solids present in the SMECT based upon samples from that tank.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

200-IA-1 Operable Unit Human Health Risk and Kd Screen

The purpose of this environmental calculation file (ECF) is to provide the following: Document the data processing and data reduction steps taken to prepare the 200-IA-1 Operable Unit (OU) data set that will be used to calculate the sample-specific screening level human health risk evaluation; Document the data processing and data reduction steps taken to prepare the 200-IA-1 OU data set that will be used to identify analytes that could potentially impact groundwater in the future beneath the 200-IA-1 OU representative waste sites; Document the assumptions, equations, and methodologies used to calculate the screening levels for human health cancer risks and noncancer hazards for each representative waste site assigned to the 200-IA-1 OU. Individual measured soil concentrations from 0 to 4.6 m (15 ft) below ground surface (bgs) (shallow vadose zone) are used to calculate the total excess lifetime cancer risk (ELCR) and hazard index (HI) for the outdoor worker scenario to determine if there is a basis for remedial action. Individual measured soil concentrations from the ground surface to the groundwater table are used for the distribution coefficient (Kd) screen to identify analytes that could potentially impact groundwater in the future beneath the 200-IA-1 OU representative waste sites. This ECF supports DOE/RL-2020-51, 200-IA-1 OU Focused Feasibility Study, under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). A risk characterization based upon the evaluation of the health risk estimates developed in this ECF will be presented in the focused feasibility study report.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗

Neutron energy spectrum from 120 GeV protons on a thick copper target

Neutron energy spectrum from 120 GeV protons on a thick copper target was measured at the Meson Test Beam Facility (MTBF) at Fermi National Accelerator Laboratory. The data allows for evaluation of neutron production process implemented in theoretical simulation codes. It also helps exploring the reasons for some disagreement between calculation results and shielding benchmark data taken at high energy accelerator facilities, since it is evaluated separately from neutron transport. The experiment was carried out using a 120 GeV proton beam of 3E5 protons/spill. Since the spill duration was 4 seconds, protoninduced events were counted pulse by pulse. The intensity was maintained using diffusers and collimators installed in the beam line to MTBF. The protons hit a copper block target the size of which is 5cm x 5cm x 60 cm long. The neutrons produced in the target were measured using NE213 liquid scintillator detectors, placed about 5.5 m away from the target at 30{sup o} and 5 m 90{sup o} with respect to the proton beam axis. The neutron energy was determined by time-of-flight technique using timing difference between the NE213 and a plastic scintillator located just before the target. Neutron detection efficiency of NE213 was determined on basis of experimental data from the high energy neutron beam line at Los Alamos National Laboratory. The neutron spectrum was compared with the results of multiparticle transport codes to validate the implemented theoretical models. The apparatus would be applied to future measurements to obtain a systematic data set for secondary particle production on various target materials.

43 PARTICLE ACCELERATORS↗

Bench Scale Testing of Next Generation Hollow Fiber Membrane Modules

This project seeks to develop a next generation membrane material (PI-2) for application in Air Liquide’s (AL) hybrid process. Combining the cold membrane operation with an integrated CO 2 Compression and Purification Unit (CPU) significantly reduces the overall cost of CO 2 capture. The proposed work will accelerate the membrane bundle fabrication, scale-up and performance validation of this new material. The proposed novel membrane development, combined with the results of the previous Cold Membrane Project, will provide the best opportunity for AL to meet the long term development targets of the DOE with respect to timing, cost, and performance for CO 2 capture. Our previous field test program (DE-FE0013163) showed promising results for the hybrid process utilizing the existing commercial AL membrane bundles (PI-1 material). The project work has also shown the potential for significant improvements through initial laboratory tests with the novel material (PI-2). The initial PI-2 results show a step-change in membrane permeance. This will enable further reduction in the cost of CO 2 capture by reducing the number of membrane modules and associated equipment in the system. In order to capture this value, however, the new material needs to be validated by field testing of large bundles, representative of commercial production. Lastly, a comprehensive evaluation of novel hybrid processes and costs needs to be completed to ensure optimal use of this improved material performance. The current project seeks to develop this next generation membrane to TRL 5 (approximately 600 - 1,000 Nm3/h flue gas, 350 - 600 scfm, 0.2 - 0.3 MWe equivalent). Air Liquide manufacturing methodology will be applied to fabricate prototype (4”) membrane modules from PI-2 material. Once the manufacturing methods prove reliable with the new material, and performance is demonstrated in line with expectation, 6” commercial scale bundles will be fabricated. Recognizing that a low cost membrane solution by itself may not meet DOE’s LCOE target for CO 2 capture, we will also perform simulation studies of novel hybrid processes in combination with the next generation membrane technology. This approach has the best potential for exceeding the DOE targets. The best evaluation of the new commercial units will be performance testing under real flue gas at the NCCC. Finally, a rigorous TEA, which incorporates the novel process studies and field performance, will be completed.

36 MATERIALS SCIENCE↗

Data from Biodiesel Production from Engineered Sugarcane Lipids under Uncertain Feedstock Compositions: Process Design and Techno-Economic Analysis

In this study, different process schemes were designed and evaluated for biodiesel production from engineered cane lipids with uncertain fatty acid compositions. Four different process schemes were compared under (i) thermal glycerolysis and (ii) enzymatic glycerolysis approaches. These schemes were based on the biodiesel yield and economic indicators such as the net present value (NPV) and the minimum selling price (MSP) of biodiesel. A scheme with polar lipid separation under thermal glycerolysis resulted in the maximum NPV ($96.5 million) and minimum MSP ($1107/ton biodiesel), respectively. Through local sensitivity analysis, it was concluded that the cane lipid percentage is the most significant factor influencing process economics. A conjoint analysis of the lipid procurement price and cane lipid percent suggested that 15% cane lipids with a low lipid procurement price ($0.536/kg) results in a positive NPV. When the cane lipid price is higher (>$0.80/kg), a 20% lipid content should be considered to achieve a positive NPV. At 20% cane lipids, the worst-case and best-case scenarios were evaluated by analyzing the interplay of the three most important parameters, The best-case scenario revealed that the minimum NPV under any process scheme could yield more than $100 million (or MSP: $0.80/L), and the worst-case analysis showed that losses incurred by the plant could be as high as $80 million (MSP: $1.36/L). A Monte Carlo simulation indicated that there is a 70% chance of the plant being profitable (NPV > 0).

Conversion↗

Development of an advanced multi-scale subchannel model for CRUD risk assessments

AREVA NP has developed a process, based upon standard licensing methods and specialized applications, for the assessment of the risk of crud induced corrosion and crud induced axial off-set. This streamlined process allows for the evaluation of the crud risk for full core subchannel by subchannel models, by applying local conditions on each fuel rod/subchannel, with axial nodes spanning several centimeters. AREVA NP has applied these tools successfully to units from various NSSS vendors. To date, there have been no plant performance issues that have been outside the performance as predicted by the AREVA NP risk assessment tools. The study presented in this paper utilized the core simulator and thermal-hydraulic packages of this tool set to evaluate the effects of changing various fuel cycle design (e.g. radial zoning patterns) and fuel assembly design parameters (e.g. fuel rod diameter, spacer grid placement) on thermal-hydraulic key decision variables (KDVs) of interest. The study may be valuable as a first step towards optimizing the fuel cycle design, optimizing the fuel lattice design, or evaluating potential operating changes such as a power up-rate or modification of the cycle length for a given PWR plant. The various geometric inputs to the AREVA NP risk assessment process were tested by individually adjusting a single parameter and observing the effect. Multi-parameter studies are also included to assess the impact of optimized fuel cycle designs. The sensitivity of the model, in terms of thermal-hydraulic results, is presented. Provided a relationship between the thermal-hydraulic results to both crud deposition thickness and lithium uptake in the zirconium cladding oxide layer, approximate impacts to the risk of crud induced corrosion and crud induced axial off-set can be estimated. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Biodiesel production from engineered sugarcane lipids under uncertain feedstock compositions: Process design and techno-economic analysis

In this study, different process schemes were designed and evaluated for biodiesel production from engineered cane lipids with uncertain fatty acid compositions. Four different process schemes were compared under (i) thermal glycerolysis and (ii) enzymatic glycerolysis approaches. These schemes were based on the biodiesel yield and economic indicators such as the net present value (NPV) and the minimum selling price (MSP) of biodiesel. A scheme with polar lipid separation under thermal glycerolysis resulted in the maximum NPV ($\$96.5$ million) and minimum MSP ($\$1107$ /ton biodiesel), respectively. Through local sensitivity analysis, it was concluded that the cane lipid percentage is the most significant factor influencing process economics. A conjoint analysis of the lipid procurement price and cane lipid percent suggested that 15% cane lipids with a low lipid procurement price ($\$0.536$ /kg) results in a positive NPV. When the cane lipid price is higher (> $\$0.80$ /kg), a 20% lipid content should be considered to achieve a positive NPV. At 20% cane lipids, the worst-case and best-case scenarios were evaluated by analyzing the interplay of the three most important parameters, Here, the best-case scenario revealed that the minimum NPV under any process scheme could yield more than $\$100$ million (or MSP: $\$0.80$ /L), and the worst-case analysis showed that losses incurred by the plant could be as high as 80 million (MSP: $\$1.36$ /L). A Monte Carlo simulation indicated that there is a 70% chance of the plant being profitable (NPV > 0).

09 BIOMASS FUELS↗

Information Processing Capacity of Spintronic Oscillator

Physical reservoir computing is a framework that enables energy‐efficient information processing by using physical systems. Nonlinear dynamics in physical systems provide a computational capability that is unique to reservoirs. It is, however, difficult to find an appropriate task for a reservoir because of the complexity of nonlinear information processing. The information processing capacity has recently been used to clarify systematically the tasks that are solved by reservoirs; it quantifies the memory capacity of reservoirs in accordance with the order of nonlinearity. Herein, an experimental evaluation of the information processing capacity of a spintronic oscillator consisting of nanostructured ferromagnets is reported. The spintronic reservoir state is electrically manipulated by adding a delayed‐feedback circuit. The total capacity reaches a maximum of 5.6 at the edge of the echo state property. A trade‐off between the linear and nonlinear components of the capacity is also found. The result can be used to better understand the nonlinear information processing in reservoirs and to find good matches between reservoirs and tasks. As an example, a function‐approximation task is performed and it is found that it can be efficiently solved when the reservoir state is appropriately tuned so that its information processing capacity matches that of the task.

97 MATHEMATICS AND COMPUTING↗

Validation of KENO Thermal Moderator Doppler Broadening Method in SCALE 6.2 Beta5 Using Continuous-Energy B-VII.1 Library

KENO, the Monte Carlo criticality safety program within the SCALE code package, has until recently used continuous-energy (CE) cross sections corresponding to the set of evaluated nuclear data closest to the temperature of interest. This method, which is used for both 1-D cross sections and thermal scattering probability data, does not fully represent the phenomenon of Doppler broadening (DB) and can result in significant differences in eigenvalues when the material temperature lies between the evaluated data sets. A method for creating temperature-dependent nuclear data has been implemented in KENO for CE calculations. This work summarizes the results of incorporating this method into two critical experiments using low-enriched uranium (LEU) in light water moderated pin lattices. The LEUCOMP-THERM-046 (LCT-046) experiment is a benchmark documented in the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook); it consists of 22 critical configurations or cases. The KRITZ-2:1 experiment, a part of the International Reactor Physics Experiment Evaluation Project (IRPhEP), consists of two cases which span a significant range of moderator temperatures. The results of this work give a good indication of the value of the newly incorporated cross section processing. However, more diverse evaluations should be performed to provide a broader validation of this method. The results suggest that when dealing with systems similar to LCT-046, there is a significant improvement made when the moderator scattering data are properly broadened and sampled. The DB of the hydrogen (in water) 2-D cross sections resulted in a consistent C/E value across the temperature range, whereas the DB of the 1-D only cross sections did not exhibit this improvement. With respect to criticality safety, this consistency adds precision to the calculational method, which could potentially impact subcriticality limits. After comparing the KRITZ and LCT-046 results, the most plausible conclusion to make as to why the added thermal moderator treatment improved the results for LCT-046 and not for the KRITZ experiment is that the two systems were dissimilar with respect to their temperatures. That is, the relative temperature differences among the cases in each experiment are more significant for LCT-046 than for KRITZ. The cross section changes as a function of temperature are also smaller at higher temperatures. This difference resulted in a lesser impact of broadening in general for the KRITZ hot case.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Using MARCUS, MICRE, and COMBLE data to improve understanding and modeling of cloud, aerosol, and boundary layer processes at high-latitudes

Because it is believed general circulation (GCM) and numerical weather prediction (NWP) models underestimate shortwave radiation over the Southern Ocean (SO) due to inadequate representations of boundary layer (BL) and cloud processes, it is critical to improve our understanding of key aerosol, cloud, precipitation, and BL processes. Over the north Atlantic Ocean (NA), cold-air outbreaks are common, yet few studies of the aerosol and environmental controls of the associated convective BL clouds exist as needed to develop and evaluate GCM representations. Although processes cannot be observed, cloud and aerosol properties can be measured in-situ or remotely retrieved, which when combined with numerical simulations enable process level understanding required to improve model representations.

54 ENVIRONMENTAL SCIENCES↗

DWPF SB6 INITIAL CPC FLOWSHEET TESTING SB6-1 TO SB6-4L TESTS OF SB6-A AND SB6-B SIMULANTS

The Defense Waste Processing Facility (DWPF) will transition from Sludge Batch 5 (SB5) processing to Sludge Batch 6 (SB6) processing in late fiscal year 2010. Tests were conducted using non-radioactive simulants of the expected SB6 composition to determine the impact of varying the acid stoichiometry during the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) processes. The work was conducted to meet the Technical Task Request (TTR) HLW/DWPF/TTR-2008-0043, Rev.0 and followed the guidelines of a Task Technical and Quality Assurance Plan (TT&QAP). The flowsheet studies are performed to evaluate the potential chemical processing issues, hydrogen generation rates, and process slurry rheological properties as a function of acid stoichiometry. These studies were conducted with the estimated SB6 composition at the time of the study. This composition assumed a blend of 101,085 kg of Tank 4 insoluble solids and 179,000 kg of Tank 12 insoluble solids. The current plans are to subject Tank 12 sludge to aluminum dissolution. Liquid Waste Operations assumed that 75% of the aluminum would be dissolved during this process. After dissolution and blending of Tank 4 sludge slurry, plans included washing the contents of Tank 51 to {approx}1M Na. After the completion of washing, the plan assumes that 40 inches on Tank 40 slurry would remain for blending with the qualified SB6 material. There are several parameters that are noteworthy concerning SB6 sludge: (1) This is the second batch DWPF will be processing that contains sludge that has had a significant fraction of aluminum removed through aluminum dissolution; (2) The sludge is high in mercury, but the projected concentration is lower than SB5; (3) The sludge is high in noble metals, but the projected concentrations are lower than SB5; and(4) The sludge is high in U and Pu - components that are not added in sludge simulants. Six DWPF process simulations were completed in 4-L laboratory-scale equipment using two projections of the SB6 blend simulant composition (Tank 40 simulant after Tank 51 transfer is complete). The more washed simulant (SB6-A) had a set of four SRAT and SME simulations at varying acid stoichiometry levels (90%, 100%, 120% and 150%) using the Koopman Acid Prediction Calculation. Two additional SRAT simulations were made using SB6-B blend simulant at 100% and 120% of acid stoichiometry. SME cycles were noted performed for the SB6B simulants to allow the SRAT products to be used for melt rate testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

TH-AB-BRA-04: Dosimetric Evaluation of MR-Guided HDR Brachytherapy Planning for Cervical Cancer

Purpose: To perform a retrospective study on 16 patients that had both CT and T2-weighted MR scans done at first fraction using the Utrecht CT/MR applicator (Elekta Brachytherapy) in order to evaluate uncertainties associated with an MR-only planning workflow. Methods: MR-workflow uncertainties were classified in three categories: reconstruction, registration and contouring. A systematic comparison of the CT and MR contouring, manual reconstruction and optimization process was performed to evaluate the impact of these uncertainties on the recommended GEC ESTRO DVH parameters: D90% and V100% for HR-CTV as well as D2cc for bladder, rectum, sigmoid colon and small bowel. This comparison was done using the following four steps: 1. Catheter reconstruction done on MR images with original CT-plan contours and dwell times. 2. OAR contours adjusted on MR images with original CT-plan reconstruction and dwell times. 3. Both reconstruction and contours done on MR images with original CT-plan dwell times. 4. Entire MR-based workflow optimized dwell times reimported to the original CT-plan. Results: The MR-based reconstruction process showed average D2cc deviations of 4.5 ± 3.0%, 1.5 ± 2.0%, 2.5 ± 2.0% and 2.0 ± 1.0% for the bladder, rectum, sigmoid colon and small bowels respectively with a maximum of 10%, 6%, 6% and 4%. The HR-CTV’s D90% and V100% average deviations was found to be 4.0 ± 3.0%, and 2.0 ± 2.0% respectively with a maximum of 10% and 6%. Adjusting contours on MR-images was found to have a similar impact. Finally, the optimized MR-based workflow dwell times were found to still give acceptable plans when re-imported to the original CT-plan which validated the entire workflow. Conclusion: This work illustrates a systematic validation method for centers wanting to move towards an MR-only workflow. This work will be expanded to model based reconstruction, PD-weighted images and other types of applicators.

60 APPLIED LIFE SCIENCES↗

Modular evaluation method for subsurface activities (MEMSA). A novel approach for integrating social acceptance in a permit decision-making process for subsurface activities

We investigate how the decision support system ‘Modular Evaluation Method Subsurface Activities’ (MEMSA) can help facilitate an informed decision-making process for permit applications of subsurface activities. To this end, we analyze the extent the MEMSA approach allows for a dialogue between stakeholders in a transparent manner. We use the exploration permit for the underground gas storage facility at the Pieterburen salt dome (Netherlands) as a case study. The results suggest that the MEMSA approach is flexible enough to adjust to changing conditions. Furthermore, MEMSA provides a novel way for identifying structural problems and possible solutions in permit decision-making processes for subsurface activities, on the basis of the sensitivity analysis of intermediate rankings. We suggest that the planned size of an activity should already be specified in the exploration phase, because this would allow for a more efficient use of the subsurface as a whole. We conclude that the host community should be involved to a greater extent and in an early phase of the permit decision-making process, for example, already during the initial analysis of the project area of a subsurface activity. We suggest that strategic national policy goals are to be re-evaluated on a regular basis, in the form of a strategic vision for the subsurface, to account for timing discrepancies between the realization of activities and policy deadlines, because this discrepancy can have a large impact on the necessity and therefore acceptance of a subsurface activity.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

'PSA-SPN' - A Parameter Sensitivity Analysis Method Using Stochastic Petri Nets: Application to a Production Line System

The dynamic behavior of a discrete event dynamic system can be significantly affected for some uncertain changes in its decision parameters. So, parameter sensitivity analysis would be a useful way in studying the effects of these changes on the system performance. In the past, the sensitivity analysis approaches are frequently based on simulation models. In recent years, formal methods based on stochastic process including Markov process are proposed in the literature. In this paper, we are interested in the parameter sensitivity analysis of discrete event dynamic systems by using stochastic Petri nets models as a tool for modelling and performance evaluation. A sensitivity analysis approach based on stochastic Petri nets, called PSA-SPN method, will be proposed with an application to a production line system.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SLUDGE BATCH 5 SIMULANT FLOWSHEET STUDIES

The Defense Waste Processing Facility (DWPF) will transition from Sludge Batch 4 (SB4) processing to Sludge Batch 5 (SB5) processing in early fiscal year 2009. Tests were conducted using non-radioactive simulants of the expected SB5 composition to determine the impact of varying the acid stoichiometry during the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) processes. The work was conducted to meet the Technical Task Request (TTR) HLW/DWPF/TTR-2007-0007, Rev. 1 and followed the guidelines of a Task Technical and Quality Assurance Plan (TT&QAP). The flowsheet studies are performed to evaluate the potential chemical processing issues, hydrogen generation rates, and process slurry rheological properties as a function of acid stoichiometry. Initial SB5 flowsheet studies were conducted to guide decisions during the sludge batch preparation process. These studies were conducted with the estimated SB5 composition at the time of the study. The composition has changed slightly since these studies were completed due to changes in the washing plan to prepare SB5 and the estimated SB4 heel mass. Nine DWPF process simulations were completed in 4-L laboratory-scale equipment using both a batch simulant (Tank 51 simulant after washing is complete) and a blend simulant (Tank 40 simulant after Tank 51 transfer is complete). Each simulant had a set of four SRAT and SME simulations at varying acid stoichiometry levels (115%, 130%, 145% and 160%). One additional run was made using blend simulant at 130% acid that included additions of the Actinide Removal Process (ARP) waste prior to acid addition and the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) waste following SRAT dewatering. There are several parameters that are noteworthy concerning SB5 sludge: (1) This is the first batch DWPF will be processing that contains sludge that has had a significant fraction of aluminum removed through aluminum dissolution. (2) The sludge is high in mercury. (3) The sludge is high in noble metals. (4) The sludge is high in U and Pu--components that are not added in sludge simulants. Two SB5 processing issues were noted during testing. First, high hydrogen generation rates were measured during experiments with both the blend and batch simulant at high acid stoichiometry. Also, the reflux time was extended due to the high mercury concentration in both the batch and blend simulant. Adding ARP will extend processing times in DWPF. The ARP caustic boil took approximately six hours. The boiling time during the experiment with added MCU was 14 hours at the maximum DWPF steam flux rate. This is comparable to the DWPF processing time for dewatering plus reflux without MCU at a 5000 lbs/hr boil-up rate, but would require significantly more time at boiling at 2000-2500 lbs/hr boil-up rate. The addition of ARP and MCU did not cause any other processing issues, since foaming, rheology and hydrogen generation were less of an issue while processing with ARP/MCU.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Progress Report for Diffusion Welding of the NGNP Process Application Heat Exchangers (Revision 1)

The U.S. Department of Energy selected the high temperature gas-cooled reactor as the basis for the Next Generation Nuclear Plant (NGNP). The NGNP will demonstrate the use of nuclear power for electricity, hydrogen production, and process heat applications. The NGNP Project is currently investigating the use of metallic, diffusion welded, compact heat exchangers to transfer heat from the primary (reactor side) heat transport system to the secondary heat transport system. An intermediate heat exchanger will transfer this heat to downstream applications such as hydrogen production, process heat, and electricity generation. The channeled plates that make up the heat transfer surfaces of the intermediate heat exchanger will have to be assembled into an array by diffusion welding. This report describes the preliminary results of a scoping study that evaluated the diffusion welding process parameters and the resultant mechanical properties of diffusion welded joints using Alloy 800H. The long-term goal of the program is to progress towards demonstration of small heat exchanger unit cells fabricated with diffusion welds. Demonstration through mechanical testing of the unit cells will support American Society of Mechanical Engineers rules and standards development, reduce technical risk, and provide proof of concept for heat exchanger fabrication methods needed to deploy heat exchangers in several potential NGNP configurations.1 Researchers also evaluated the usefulness of modern thermodynamic and diffusion computational tools (Thermo-Calc and Dictra) in optimizing the parameters for diffusion welding of Alloy 800H. The modeling efforts suggested a temperature of 1150°C for 1 hour with an applied pressure of 5 MPa using 15 μm nickel foil as joint filler to reduce chromium oxidation on the welded surfaces. Good agreement between modeled and experimentally determined concentration gradients was achieved

08 HYDROGEN↗

Complete calculation of evaluated Maxwellian-averaged cross sections and their uncertainties for s-process nucleosynthesis

Present contribution represents a significant improvement of our previous calculation of Maxwellian-averaged cross sections and astrophysical reaction rates. Addition of newly-evaluated neutron reaction libraries, such as ROSFOND and Low-Fidelity Covariance Project, and improvements in data processing techniques allowed us to extend it for entire range of sprocess nuclei, calculate Maxwellian-averaged cross section uncertainties for the first time, and provide additional insights on all currently available neutron-induced reaction data. Nuclear reaction calculations using ENDF libraries and current Java technologies will be discussed and new results will be presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗