Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aerodynamic modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Modeling of a Sequential Two-Stage Combustor, Supplement

A sequential two-stage, natural gas fueled power generation combustion system is modeled to examine the fundamental aerodynamic and combustion characteristics of the system. The modeling methodology includes CAD-based geometry definition, and combustion computational fluid dynamics analysis. Graphical analysis is used to examine the complex vortical patterns in each component, identifying sources of pressure loss. The simulations demonstrate the importance of including the rotating high-pressure turbine blades in the computation, as this results in direct computation of combustion within the first turbine stage, and accurate simulation of the flow in the second combustion stage. The direct computation of hot-streaks through the rotating high-pressure turbine stage leads to improved understanding of the aerodynamic relationships between the primary and secondary combustors and the turbomachinery.

Hendricks, R. C.↗
NASA NTRS1999

Aerodynamic Characteristics and Control Effectiveness of the HL-20 Lifting Body Configuration at Mach 10 in Air

A 0.0196-scale model of the HL-20 lifting-body, one of several configurations proposed for future crewed spacecraft, was tested in the Langley 31-Inch Mach 10 Tunnel. The purpose of the tests was to determine the effectiveness of fin-mounted elevons, a lower surface flush-mounted body flap, and a flush-mounted yaw controller at hypersonic speeds. The nominal angle-of-attack range, representative of hypersonic entry, was 2 deg to 41 deg, the sideslip angles were 0 deg, 2 deg, and -2 deg, and the test Reynolds number was 1.06 x 10 E6 based on model reference length. The aerodynamic, longitudinal, and lateral control effectiveness along with surface oil flow visualizations are presented and discussed. The configuration was longitudinally and laterally stable at the nominal center of gravity. The primary longitudinal control, the fin-mounted elevons, could not trim the model to the desired entry angle of attack of 30 deg. The lower surface body flaps were effective for roll control and the associated adverse yawing moment was eliminated by skewing the body flap hinge lines. A yaw controller, flush-mounted on the lower surface, was also effective, and the associated small rolling moment was favorable.

Scallion, William I.↗
NASA NTRS1992

Propulsion simulator for magnetically suspended wind tunnel models

Simulation of propulsion induced aerodynamic forces and moments, which arise as a result of interactions between propulsive jets and the free stream, is one of the most desired capabilities in magnetic suspension wind tunnels. The feasibility of generating exhaust jets of appropriate characteristics onboard magnetically suspended models was examined. Four concepts of remotely operated propulsion simulators was considered. Three conceptual designs involving conventional technologies such as compressed gas cylinders, liquid monopropellants, and solid propellants were developed. The fourth concept, a laser assisted thruster, which can potentially simulate both inlet and exhaust flows, was found to require very high power levels. The measurement of aerodynamic forces and/or moments were demonstrated, including the effects of exhaust jets, in MSBS wind tunnels. Two propulsion simulator models were developed, a small scale and a large scale unit, both using compressed, liquified CO2 as propellant. Results of the wind tunnel tests with the small scale simulator are discussed.

Joshi, P. B.↗
NASA NTRS2013

A CFD Database for Airfoils and Wings at Post-Stall Angles of Attack

This paper presents selected results from an ongoing effort to develop an aerodynamic database from Reynolds-Averaged Navier-Stokes (RANS) computational analysis of airfoils and wings at stall and post-stall angles of attack. The data obtained from this effort will be used for validation and refinement of a low-order post-stall prediction method developed at NCSU, and to fill existing gaps in high angle of attack data in the literature. Such data could have potential applications in post-stall flight dynamics, helicopter aerodynamics and wind turbine aerodynamics. An overview of the NASA TetrUSS CFD package used for the RANS computational approach is presented. Detailed results for three airfoils are presented to compare their stall and post-stall behavior. The results for finite wings at stall and post-stall conditions focus on the effects of taper-ratio and sweep angle, with particular attention to whether the sectional flows can be approximated using two-dimensional flow over a stalled airfoil. While this approximation seems reasonable for unswept wings even at post-stall conditions, significant spanwise flow on stalled swept wings preclude the use of two-dimensional data to model sectional flows on swept wings. Thus, further effort is needed in low-order aerodynamic modeling of swept wings at stalled conditions.

Petrilli, Justin↗
NASA NTRS2008

Ares-I-X Stability and Control Flight Test: Analysis and Plans

The flight test of the Ares I-X vehicle provides a unique opportunity to reduce risk of the design of the Ares I vehicle and test out design, math modeling, and analysis methods. One of the key features of the Ares I design is the significant static aerodynamic instability coupled with the relatively flexible vehicle - potentially resulting in a challenging controls problem to provide adequate flight path performance while also providing adequate structural mode damping and preventing adverse control coupling to the flexible structural modes. Another challenge is to obtain enough data from the single flight to be able to conduct analysis showing the effectiveness of the controls solutions and have data to inform design decisions for Ares I. This paper will outline the modeling approaches and control system design to conduct this flight test, and also the system identification techniques developed to extract key information such as control system performance (gain/phase margins, for example), structural dynamics responses, and aerodynamic model estimations.

Brandon, Jay M.↗
NASA NTRS1974

Wind tunnel investigation of helicopter rotor wake effects on three helicopter fuselage models

The effects of rotor downwash on helicopter fuselage aerodynamic characteristics were investigated. A rotor model for generating the downwash was mounted close to each of three fuselage models. The main report presents the force and moment data in both graphical and tabular form and the pressure data in graphical form. This supplement presents the pressure data in tabular form. Each run or parameter sweep is identified by a unique run number. The data points in each run are identified by a point number. The pressure data can be matched to the force data by matching the run and point number.

Wilson, J. C.↗
NASA NTRS1979

Test technique development in interference free testing, flow visualization, and remote control model technology at Langley's Unitary Plan wind tunnel

A metric half-span model is considered as a means of mechanical support for a wind-tunnel model which allows measurement of aerodynamic forces and moments without support interference or model distortion. This technique can be applied to interference-free propulsion models. The vapor screen method of flow visualization at supersonic Mach numbers is discussed. The use of smoke instead of water vapor as a medium to produce the screen is outlined. Vapor screen data are being used in the development of analytical vortex tracking programs. Test results for a remote control model system are evaluated. Detailed control effectiveness and cross-coupling data were obtained with a single run. For the afterbody tail configuration, tested control boundaries at several roll orientations were established utilizing the facility's on-line capability to 'fly' the model in the wind tunnel.

Corlett, W. A.↗
NASA NTRS1978

GASP- General Aviation Synthesis Program. Volume 6: Performance

Aircraft performance modeling requires consideration of propulsion, aerodynamics, and weight characteristics. Eleven subroutines used in modeling aircraft performance are presented and their interactions considered. Manuals for performance model users and programmers are included.

Hague, D.↗
NASA NTRS1974

Aerodynamic results of a support system interference effects test conducted at NASA/LaRC UPWT using an 0.015-scale model of the configuration 140A/B SSV orbiter (0A20B)

An experimental aerodynamic investigation was conducted to determine the interference effects of a wind tunnel support system. The test article was a 0.015 scale model of the space shuttle orbiter. The primary objective of the test was to determine the extent that aerodynamic simulation of the space shuttle orbiter is affected by base mounting the model, without nozzles, on a straight sting. Two support systems were tested. The characteristics of the support systems are described. Data from the tests are presented in the form of graphs and tables.

Campbell, J. H., II↗
NASA NTRS1994

Control of maglev vehicles with aerodynamic and guideway disturbances

A modeling, analysis, and control design methodology is presented for maglev vehicle ride quality performance improvement as measured by the Pepler Index. Ride quality enhancement is considered through active control of secondary suspension elements and active aerodynamic surfaces mounted on the train. To analyze and quantify the benefits of active control, the authors have developed a five degree-of-freedom lumped parameter model suitable for describing a large class of maglev vehicles, including both channel and box-beam guideway configurations. Elements of this modeling capability have been recently employed in studies sponsored by the U.S. Department of Transportation (DOT). A perturbation analysis about an operating point, defined by vehicle and average crosswind velocities, yields a suitable linearized state space model for multivariable control system analysis and synthesis. Neglecting passenger compartment noise, the ride quality as quantified by the Pepler Index is readily computed from the system states. A statistical analysis is performed by modeling the crosswind disturbances and guideway variations as filtered white noise, whereby the Pepler Index is established in closed form through the solution to a matrix Lyapunov equation. Data is presented which indicates the anticipated ride quality achieved through various closed-loop control arrangements.

Flueckiger, Karl↗
NASA NTRS2010

Real-Time Aerodynamic Parameter Estimation without Air Flow Angle Measurements

A technique for estimating aerodynamic parameters in real time from flight data without air flow angle measurements is described and demonstrated. The method is applied to simulated F-16 data, and to flight data from a subscale jet transport aircraft. Modeling results obtained with the new approach using flight data without air flow angle measurements were compared to modeling results computed conventionally using flight data that included air flow angle measurements. Comparisons demonstrated that the new technique can provide accurate aerodynamic modeling results without air flow angle measurements, which are often difficult and expensive to obtain. Implications for efficient flight testing and flight safety are discussed.

Morelli, Eugene A.↗
NASA NTRS1992

Tilt rotor hover aeroacoustics

The methodology, results, and conclusions of a study of tilt rotor hover aeroacoustics and aerodynamics are presented. Flow visualization and hot wire velocity measurement were performed on a 1/12-scale model of the XV-15 Tilt Rotor Aircraft in hover. The wing and fuselage below the rotor cause a complex recirculating flow. Results indicate the physical dimensions and details of the flow including the relative unsteadiness and turbulence characteristics of the flow. Discrete frequency harmonic thickness and the loading noise mechanism were predicted using WOPWOP for the standard metal blades and the Advanced Technology Blades. The recirculating flow created by the wing below the rotor is a primary sound mechanism for a hovering tilt rotor. The effects of dynamic blade response should be included for fountain flow conditions which produce impulsive blade loading. Broadband noise mechanisms were studied using Amiet's method with azimuthally varying turbulence characteristics derived from the measurements. The recirculating fountain flow with high turbulence levels in the recirculating zone is the dominant source of broadband noise for a hovering rotor. It is shown that tilt rotor hover aeroacoustic noise mechanisms are now understood. Noise predictions can be made based on reasonably accurate aerodynamic models developed here.

Coffen, Charles David↗
NASA NTRS1962

Jet Interference Effects on a Model of a Single-Engine Four Jet V/STOL Airplane at Mach Numbers from 0.60 to 1.00

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the interference from four exhaust jets on the aerodynamic characteristics of a model of a V/STOL airplane. The single- engine four-jet turbofan power plant of the airplane was simulated by inducing tunnel airflow through two large side inlets and injecting the decomposition products of hydrogen peroxide into the internal flow. The heated gas mixture was exhausted through four nozzles located on the sides of the fuselage under the wing, two near the wing leading edge and two forward of the trailing edge; the nozzles were deflected downward 1.5 deg and outward 5.0 deg to simulate cruise conditions. The wing of the model was a clipped delta with leading-edge sweep of 40 deg, aspect ratio of 3.06, taper ratio of 0.218, thickness-chord ratio of 0.09 at the root and 0.07 at the tip, and 10 deg negative dihedral. Aerodynamic and longitudinal stability coefficients were obtained for the model with the tail removed, and for horizontal-tail incidences of 0 deg and -5 deg. Data were obtained at Mach numbers from 0.60 to 1.00, angles of attack from 0 deg to 12 deg, and with jet total-pressure ratios up to 3.1. Jet operation generally caused a decrease in lift, an increase in pitching-moment coefficient, and a decrease in longitudinal stability at subsonic speeds. The jet interference effects on drag were detrimental at a Mach number of 0.60 and favorable at higher speeds for cruising-flight attitudes.

Schmeer, James W.↗
NASA NTRS1976

Aerodynamic results of wind tunnel tests on a 0.010-scale model (32-QTS) space shuttle integrated vehicle in the AEDC VKF-40-inch supersonic wind tunnel (IA61)

Plotted and tabulated aerodynamic coefficient data from a wind tunnel test of the integrated space shuttle vehicle are presented. The primary test objective was to determine proximity force and moment data for the orbiter/external tank and solid rocket booster (SRB) with and without separation rockets firing for both single and dual booster runs. Data were obtained at three points (t = 0, 1.25, and 2.0 seconds) on the nominal SRB separation trajectory.

Daileda, J. J.↗
NASA NTRS1961

Transonic Investigation of Aerodynamic Characteristics of a Swept-Wing Fighter-Airplane Model with Leading-Edge Droop in Combination with Outboard Chord-Extensions and Notches

An investigation of the effects of several wing leading-edge modifications on the aerodynamic characteristics of a 45 degree swept-wing fighter-airplane model has been conducted in the Langley 16-foot transonic tunnel at low and high lifting conditions at Mach numbers from 0.85 to 1.03. The investigation included the determination of the effect on longitudinal stability and performance characteristics of wing leading-edge and chord-extension droops of 60 and 20 degrees chord-extension overhangs of 0.075c and 0.15c (where c inboard end of the 0.075c chord-extension to depths of 0.075c and 0.l25c, and indention of the model fuselage to conform partially to the supersonic area rule for a Mach number of 1.20. Lift, drag, and pitching-moment data were obtained for configurations with the tail on and off. Comparisons of data obtained from the present model with data from a configuration with leading-edge slats are included. Generally, the model wing modifications provided only slight improvements of the airplane longitudinal stability characteristics, but did substantially reduce the airplane drag coefficients at moderate and high lifting conditions.

Whitcomb, Charles F.↗
NASA NTRS1976

Aerodynamic results of a separation effects test on a 0.010-scale model (52-OTS) of the integrated SSV in the AEDC/VKF 40-by-40 inch supersonic wind tunnel A (IA111), volume 1

Graphical data obtained during experimental wind tunnel aerodynamic investigations of a 0.010 scale model (52-OTS) of the integrated space shuttle vehicle was presented. The purpose of this investigation was to obtain data with the solid rocket booster (SRB) in proximity to the orbiter/external tank (O/ET), over a large O/ET initial angle of attack and sideslip range, as well as data on the SRB alone (greatly separated from the O/ET). A captive trajectory system, which supported the SRB, was used with the tunnel primary sector (supporting the O/ET) to obtain grid type separation effects data. One symmetrical SRB model was used interchangeably to obtain right-hand and left-hand SRB data. The entire investigation was conducted at a free-stream Mach number of 4.5 at unit Reynolds number of 3.95 and 5.9 million per foot.

Chee, E.↗
NASA NTRS1976

Aerodynamic results of a separation effects test on a 0.010-scale model (52-OTS) of the integrated SSV in the AEDC/VKF 40-by-40 inch supersonic wind tunnel A (IA111), volume 2

Tabular data obtained during experimental wind tunnel aerodynamic investigations of a 0.010 scale model (52-OTS) of the integrated space shuttle vehicle was presented. The purpose of this investigation was to obtain data with the solid rocket booster (SRB) in proximity to the orbiter/external tank (O/ET), over a large O/ET initial angle of attack and sideslip range, as well as data on the SRB alone (greatly separated from the O/ET). A captive trajectory system, which supported the SRB, was used with the tunnel primary sector (supporting the O/ET) to obtain grid type separation effects data. One symmetrical SRB model was used interchangeably to obtain right-hand and left-hand SRB data. The entire investigation was conducted at free-stream Mach number of 4.5 at unit Reynolds number of 3.95 and 5.9 million per foot.

Chee, E.↗