SEARCH · Engineering Papers

Results for “Simulation Quality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Experimental and Computational Sonic Boom Assessment of Boeing N+2 Low Boom Models

Near-field pressure signatures were measured and computational predictions made for several sonic boom models representing Boeing's Quiet Experimental Validation Concept (QEVC) supersonic transport, as well as three axisymmetric calibration models. Boeing developed the QEVC under a NASA Research Announcement (NRA) contract for Experimental Systems Validations for N+2 Supersonic Commercial Transport Aircraft, which was led by the NASA High Speed Project under the Fundamental Aeronautics Program. The concept was designed to address environmental and performance goals given in the NRA, specifically for low sonic boom loudness levels and high cruise efficiency, for an aircraft anticipated to enter service in the 2020 timeframe. Wind tunnel tests were conducted on the aircraft and calibration models during Phases I and II of the NRA contract from 2011 to 2013 in the NASA Ames 9- by 7-Foot and NASA Glenn 8- by 6-Foot Supersonic Wind Tunnels. Sonic boom pressure signatures were acquired primarily at Mach 1.6 and 1.8, and force and moment data were acquired from Mach 0.8 to 1.8. The sonic boom test data were obtained using a 2-in. flat-top pressure rail and a 14-in. round-top tapered "reflection factor 1" (RF1) pressure rail. Both rails capture an entire pressure signature in one data point, and successive signatures at varying positions along or above the rail were used to improve data quality through spatial averaging. The sonic boom data obtained by the rails were validated with high-fidelity numerical simulations of off-body pressures using the CFD codes USM3D, Cart3D, and OVERFLOW. The test results from the RF1 rail showed good agreement between the computational and experimental data when a variety of testing techniques including spatial averaging of a series of pressure signatures were employed, however, reflections off the 2-in. flat-top rail caused distortions in the signatures that did not agree with the CFD predictions. The 9 x 7 and 8 x 6 wind tunnels generally produced comparable data.

pressure signature↗

NASA NTRS2014

Experimental and Computational Sonic Boom Assessment of Boeing N+2 Low Boom Models

Near-field pressure signatures were measured and computational predictions made for several sonic boom models representing Boeing’s Quiet Experimental Validation Concept (QEVC) supersonic transport, as well as for three axisymmetric calibration models. The concept was designed under a NASA Research Announcement (NRA) contract to address environmental and performance goals, specifically for low sonic boom loudness levels and high cruise efficiency, for an aircraft anticipated to enter service in the 2020-timeframe. Wind tunnel tests were conducted on the aircraft and calibration models during Phases I and II of the NRA contract from 2011 to 2013 in the NASA Ames 9- by 7-Foot and NASA Glenn 8- by 6-Foot Supersonic Wind Tunnels. Sonic boom pressure signatures were acquired primarily at Mach 1.6 and 1.8, and force and moment data were acquired from Mach 0.8 to 1.8. The sonic boom test data were obtained using a 2-in. flat-top pressure rail and a 14-in. tapered “reflection factor 1” (RF1) pressure rail. Both rails capture an entire pressure signature in one data point, and successive signatures at varying positions along or above the rail were used to improve data quality through spatial averaging. The sonic boom data obtained by the rails were validated with high-fidelity numerical simulations of offbody pressures. The test results showed good agreement between the computational and experimental data when a variety of testing techniques including spatial averaging of a series of pressure signatures were employed. The two wind tunnels generally produced comparable data.

Durston, Donald A.↗

NASA NTRSDate not supplied

Version 8 of the SMAP Level-4 Soil Moisture Data Assimilation Product

The NASA Soil Moisture Active Passive (SMAP) mission Level-4 Soil Moisture (L4_SM) product provides global, 9-km resolution, 3-hourly surface (0-5 cm) and root-zone (0-100 cm) soil moisture from April 2015 to present with a mean latency of 2.5 days from the time of observation. The product is based on the assimilation of SMAP L-band (1.4 GHz) brightness temperature (Tb) observations into the NASA Catchment land surface model as the model is driven with observations-based precipitation forcing. This presentation discusses the improvements in the forthcoming Version 8 of L4_SM, including updates in the precipitation forcing, the Catchment model parameters, and the L-band microwave radiative transfer model (mwRTM). The precipitation observations used in L4_SM Version 8 outside of North America and the high latitudes are from the latest (Version 7) NASA Integrated Multi-satellitE Retrievals for the Global Precipitation Measurement mission (IMERG) products. Moreover, occasionally excessive precipitation rates in earlier versions of L4_SM along certain longitudes in North America were eliminated by a bug fix in the precipitation corrections algorithm. The Catchment model in L4_SM Version 8 uses climatological snow albedo values based on observations from the Moderate Resolution Imaging Spectroradiometer, replacing the look-up table parameterization of earlier versions. Additionally, corrected soil parameters were implemented for a small region in Argentina that had erroneously been classified as peat because of an error in the ancillary soil data. Finally, the mwRTM in L4_SM Version 8 uses the Mironov soil mixing approach and updated values of the L-band scattering albedo, soil roughness, and vegetation opacity climatology obtained from the latest (Release 19) SMAP Level-2 dual-channel soil moisture retrieval product. During the development of L4_SM Version 8, the change in the mwRTM parameterization resulted in a reduced unbiased RMSE of surface soil moisture when verified against in situ measurements. It also reduced the standard deviation of the Tb observation-minus-forecast residuals by ~0.15 K, highlighting the importance of the mwRTM for successful data assimilation. The bug fixes in the precipitation corrections algorithm and the Catchment model soil parameters in the Argentina region result in locally large improvements of the simulated land surface states. In summary, the ongoing refinements of the L4_SM product continue to improve its science quality and performance for global soil moisture monitoring

Rolf Reichle↗

DOE OSTI2024

Adsorption Thermodynamics for Process Simulation

Adsorption has rapidly evolved in recent decades and is an established separation technology extensively practiced in gas separation industries and others. However, rigorous thermodynamic modeling of multicomponent adsorption equilibrium remains elusive, and industrial practitioners rely heavily on expensive and time-consuming trial-and-error pilot studies to develop adsorption units. Here, this article highlights the need for rigorous adsorption thermodynamic models and the limitations and deficiencies of existing models such as the extended Langmuir isotherm, dual-process Langmuir isotherm, and adsorbed solution theory. It further presents a series of recent advances in the generalization of the classical Langmuir isotherm of single-component adsorption by deriving an activity coefficient model to account for the adsorbed phase adsorbate–adsorbent interactions, substituting adsorbed phase adsorbate and vacant site concentrations with activities, and extending to multicomponent competitive adsorption equilibrium, both monolayer and multilayer. Requiring a minimum set of physically meaningful model parameters, the generalized Langmuir isotherm for monolayer adsorption and the generalized Brunauer–Emmett–Teller isotherm for multilayer adsorption address various thermodynamic modeling challenges including adsorbent surface heterogeneity, isosteric enthalpies of adsorption, BET surface areas, adsorbed phase nonideality, adsorption azeotrope formation, and multilayer adsorption. Also discussed is the importance of quality adsorption data that cover sufficient temperature, pressure, and composition ranges for reliable determination of the model parameters to support adsorption process simulation, design, and optimization.

09 BIOMASS FUELS↗

NASA NTRS2010

Flash LIDAR Emulator for HIL Simulation

NASA's Autonomous Landing and Hazard Avoidance Technology (ALHAT) project is building a system for detecting hazards and automatically landing controlled vehicles safely anywhere on the Moon. The Flash Light Detection And Ranging (LIDAR) sensor is used to create on-the-fly a 3D map of the unknown terrain for hazard detection. As part of the ALHAT project, a hardware-in-the-loop (HIL) simulation testbed was developed to test the data processing, guidance, and navigation algorithms in real-time to prove their feasibility for flight. Replacing the Flash LIDAR camera with an emulator in the testbed provided a cheaper, safer, more feasible way to test the algorithms in a controlled environment. This emulator must have the same hardware interfaces as the LIDAR camera, have the same performance characteristics, and produce images similar in quality to the camera. This presentation describes the issues involved and the techniques used to create a real-time flash LIDAR emulator to support HIL simulation.

Brewster, Paul F.↗

DOE OSTI2022

Towards a Unified Setup to Simulate Mid‐Latitude and Tropical Mesoscale Convective Systems at Kilometer‐Scales

Abstract Mesoscale convective systems (MCSs) are the main source of precipitation in the tropics and parts of the mid‐latitudes and are responsible for high‐impact weather worldwide. Studies showed that deficiencies in simulating mid‐latitude MCSs in state‐of‐the‐art climate models can be alleviated by kilometer‐scale models. However, whether these models can also improve tropical MCSs and whether we can find model settings that perform well in both regions is understudied. We take advantage of high‐quality MCS observations collected over the Atmospheric Radiation Measurement (ARM) facilities in the US Southern Great Plains (SGP) and the Amazon basin near Manaus (MAO) to evaluate a perturbed physics ensemble of simulated MCSs with 4 km horizontal grid spacing. A new model evaluation method is developed that enables to distinguish biases stemming from spatiotemporal displacements of MCSs from biases in their reflectivity and cloud shield. Amazon MCSs are similarly well simulated across these evaluation metrics than SGP MCSs despite the challenges anticipated from weaker large‐scale forcing in the tropics. Generally, SGP MCSs are more sensitive to the choice of model microphysics, while Amazon cases are more sensitive to the planetary boundary layer (PBL) scheme. Although our tested model physics combinations had strengths and weaknesses, combinations that performed well for SGP simulations result in worse results in the Amazon basin and vice versa. However, we identified model settings that perform well at both locations, which include the Thompson and Morrison microphysics coupled with the Yonsei University (YSU) PBL scheme and the Thompson scheme coupled with the Mellor‐Yamada‐Janjic PBL scheme.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

A tunable dielectric resonator for axion searches at 11 GHz

In the context of axion search with haloscopes, tunable cavity resonators with high quality factor and high effective volume at frequencies above about 8 GHz are central for probing the axion-photon coupling with the required sensitivity to reach the QCD axion models. Higher order modes in dielectrically-loaded cavities allow for higher effective volumes and larger quality factors compared to basic cylindrical cavities, but a proper cavity frequency tuning mechanism to probe broad axion mass ranges is yet not available. In this work, we report about the design and construction of a tunable prototype of a single-shell dielectric resonator with its axion-sensitive pseudo-TM$_{030}$ high-order mode at about 11 GHz frequency. A clamshell tuning method previously tested for empty cylindrical resonators has been perfected for this geometry through simulations and in situ tests conducted at cryogenic temperature. Tuning is accomplished in a range of about 2 $\%$ the central frequency, without significantly impacting the quality factor of about 175000. The experimental results presented in this work demonstrate the tunability of this type of resonator, definitely confirming its applicability to high frequency axion searches.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Long time scale multiphysics simulation of spent nuclear fuel canister in MOOSE

Pebble-bed reactors are an important class of advanced reactors under consideration for various applications where their fuel would give a significant advantage in siting and high-quality heat production. However, the disposal of their fuel is not as thoroughly studied as other fuel forms. In this study, pebble fuel is analysed in a well known spent fuel canister design to characterize the behavior of this fuel form over a long time scale. The results indicate that after approximately 100 years, decay heat is significantly reduced and the maximum temperature in the canister equalizes with the external temperature. The simulation goes on to an end time of a million years, demonstrating the capability of dealing with long time scales efficiently. We conclude that the canister temperatures seem manageable even with very aggressive loading times and while there are several improvements to be implemented in the future, MOOSE is technically capable of simulating the required scenarios.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1978

Effects of dynamic aeroelasticity on handling qualities and pilot rating

Pilot performance parameters, such as pilot ratings, tracking errors, and pilot comments, were recorded and analyzed for a longitudinal pitch tracking task on a large, flexible aircraft. The tracking task was programmed on a fixed-base simulator with a CRT attitude director display of pitch angle command, pitch angle, and pitch angle error. Parametric variations in the undamped natural frequencies of the two lowest frequency symmetric elastic modes were made to induce varying degrees of rigid body and elastic mode interaction. The results indicate that such mode interaction can drastically affect the handling qualities and pilot ratings of the task.

Swaim, R. L.↗

NASA NTRS2017

Impact of Evolving Isoprene Mechanisms on Simulated Formaldehyde: An Inter-comparison Supported by in Situ Observations from SENEX

Isoprene oxidation schemes vary greatly among gas-phase chemical mechanisms, with potentially significant ramifications for air quality modeling and interpretation of satellite observations in biogenic-rich regions. In this study, in situ observations from the 2013 SENEX mission are combined with a constrained O-D photochemical box model to evaluate isoprene chemistry among five commonly used gas-phase chemical mechanisms: CBO5, CB6r2, MCMv3.2, MCMv3.3.1, and a recent version of GEOS-Chem. Mechanisms are evaluated and inter-compared with respect to formaldehyde (HCHO), a high-yield product of isoprene oxidation. Though underestimated by all considered mechanisms, observed HCHO mixing ratios are best reproduced by MCMv3.3.1 (normalized mean bias = -15%), followed by GEOS-Chem (-17%), MCMv3.2 (-25%), CB6r2 (-32%) and CB05 (-33%). Inter-comparison of HCHO production rates reveals that major restructuring of the isoprene oxidation scheme in the Carbon Bond mechanism increases HCHO production by only approx. 5% in CB6r2 relative to CBO5, while further refinement of the complex isoprene scheme in the Master Chemical Mechanism increases HCHO production by approx. 16% in MCMv3.3.1 relative to MCMv3.2. The GEOS-Chem mechanism provides a good approximation of the explicit isoprene chemistry in MCMv3.3.1 and generally reproduces the magnitude and source distribution of HCHO production rates. We analytically derive improvements to the isoprene scheme in CB6r2 and incorporate these changes into a new mechanism called CB6r2-UMD, which is designed to preserve computational efficiency. The CB6r2-UMD mechanism mimics production of HCHO in MCMv3.3.1 and demonstrates good agreement with observed mixing ratios from SENEX (-14%). Improved simulation of HCHO also impacts modeled ozone: at approx. 0.3 ppb NO, the ozone production rate increases approx. 3% between CB6r2 and CB6r2-UMD, and rises another approx. 4% when HCHO is constrained to match observations.

isoprene↗

DOE OSTI2021

Product Consistency Test Results for the HFG1 Glasses

The U.S. Department of Energy (DOE) is responsible for building the Hanford Tank Waste Treatment and Immobilization Plant (WTP) at the Hanford site in Washington to remediate 55 million gallons of radioactive waste that is temporarily stored in 177 underground tanks. The Office of River Protection (ORP) has requested that the Savannah River National Laboratory (SRNL) contribute in areas of recognized capabilities and expertise for glass waste form development to support successful startup of the WTP. As part of this effort, the Pacific Northwest National Laboratory (PNNL) is developing, batching, and fabricating simulated high-level waste (HLW) glasses to generate the associated property data needed to validate or identify areas of potential characterization improvement in the current glass property/composition models. Currently, the models cover only a small fraction of the waste compositions projected in the Hanford tank farm; therefore, the models must be expanded to include high fluoride compositions to successfully complete the WTP mission. SRNL support of this work is defined in the Task Technical and Quality Assurance Plan (TTQAP). This report provides the results of the Product Consistency Test (PCT) leachates from the High Fluoride Glasses-1 (HFG1), a series of simulated nuclear waste glasses fabricated at PNNL. The series included quenched (Q) and canister-centerline cooled (CCC) versions of the glasses. The glasses were selected as part of a broader study of the influence of glass composition on chemical durability, sulfur retention, and other properties. These data will be used to validate or identify areas of potential characterization improvements in the current glass property/composition models.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS2000

Field Experiments with Planetary Surface Rovers: Lessons for Mars Mission Architecture

Over the last decade, a variety of field experiments have been performed that simulate operations of a rover on Mars. These, in combination with the Pathfinder experience, lead to a realistic assessment of rover mission capabilities and to recommendations for rover technology and mission architecture to improve the science return of Mars exploration. A table summarizes field experiments that represent a range of possible mission designs and operational strategies. The experiments varied by the type and quality of imaging systems and other instrumentation, the use of orbital and aerial imaging and spectroscopy, the communcation bandwidth and command strategy, and the distance traveled. All mission simulations were blind field tests operated by science teams whose interpretations were compared to field ground truth providing an assessment of the accuracy of remote science interpretations and a better understanding of where improvements are needed.

Stoker, Carol↗

DOE OSTI2022

Simulating Energy and Security Interactions in Semiconductor Manufacturing: Insights from the Intel Minifab Model

Semiconductor manufacturing is a highly complex. Fabrication plants must deal with re-entrant flows to support multiple types of wafers being produced simultaneously, each with their own deadlines and specifications. The manufacturing process itself depends upon the ability to control and programmatically adjust a variety of environmental conditions including temperature, humidity, and air quality. In addition, wafer fabrication consumes large amounts of electricity. Emerging technologies may help reduce the energy footprint of such facilities but can introduce cybersecurity risks. Therefore, this paper presents a modeling and simulation framework to quantify tradeoffs between operational measures of performance, energy consumption, and cybersecurity controls. We augment the Intel Minifab model, with the Purdue Enterprise Reference Architecture (PERA) for cybersecurity as well as tool-level energy consumption data from a real-world semiconductor manufacturing testbed. In this manner, we intend to provide stakeholders with a systematic, data-driven approach to evaluate emerging risks within the manufacturing process.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2025

BEPAM code and results for the publication 'Supplementing Biofuel Mandates with a Carbon Mitigation Policy Can Lead to Water Quality Co-benefits'

The dataset consists of: (1) The replication codes and data for the BEPAM model are contained in the "BEPAM_Supplementary Environment Policy Analysis.zip" (2) Simulation results from the BEPAM model are contained in "ModelOutputs.zip" under the "BEPAM_Supplementary Environment Policy Analysis.zip"

Fan, Xinxin [Center for Advanced Bioenergy and Bio↗

NASA NTRS2000

RFI and SCRIMP Model Development and Verification

Vacuum-Assisted Resin Transfer Molding (VARTM) processes are becoming promising technologies in the manufacturing of primary composite structures in the aircraft industry as well as infrastructure. A great deal of work still needs to be done on efforts to reduce the costly trial-and-error methods of VARTM processing that are currently in practice today. A computer simulation model of the VARTM process would provide a cost-effective tool in the manufacturing of composites utilizing this technique. Therefore, the objective of this research was to modify an existing three-dimensional, Resin Film Infusion (RFI)/Resin Transfer Molding (RTM) model to include VARTM simulation capabilities and to verify this model with the fabrication of aircraft structural composites. An additional objective was to use the VARTM model as a process analysis tool, where this tool would enable the user to configure the best process for manufacturing quality composites. Experimental verification of the model was performed by processing several flat composite panels. The parameters verified included flow front patterns and infiltration times. The flow front patterns were determined to be qualitatively accurate, while the simulated infiltration times over predicted experimental times by 8 to 10%. Capillary and gravitational forces were incorporated into the existing RFI/RTM model in order to simulate VARTM processing physics more accurately. The theoretical capillary pressure showed the capability to reduce the simulated infiltration times by as great as 6%. The gravity, on the other hand, was found to be negligible for all cases. Finally, the VARTM model was used as a process analysis tool. This enabled the user to determine such important process constraints as the location and type of injection ports and the permeability and location of the high-permeable media. A process for a three-stiffener composite panel was proposed. This configuration evolved from the variation of the process constraints in the modeling of several different composite panels. The configuration was proposed by considering such factors as: infiltration time, the number of vacuum ports, and possible areas of void entrapment.

Loos, Alfred C.↗

NASA NTRS2013

Higher Surface Ozone Concentrations Over the Chesapeake Bay than Over the Adjacent Land: Observations and Models from the DISCOVER-AQ and CBODAQ Campaigns

Air quality models, such as the Community Multiscale Air Quality (CMAQ) model, indicate decidedly higher ozone near the surface of large interior water bodies, such as the Great Lakes and Chesapeake Bay. In order to test the validity of the model output, we performed surface measurements of ozone (O3) and total reactive nitrogen (NOy) on the 26-m Delaware II NOAA Small Research Vessel experimental (SRVx), deployed in the Chesapeake Bay for 10 daytime cruises in July 2011 as part of NASA's GEO-CAPE CBODAQ oceanographic field campaign in conjunction with NASA's DISCOVER-AQ air quality field campaign. During this 10-day period, the EPA O3 regulatory standard of 75 ppbv averaged over an 8-h period was exceeded four times over water while ground stations in the area only exceeded the standard at most twice. This suggests that on days when the Baltimore/Washington region is in compliance with the EPA standard, air quality over the Chesapeake Bay might exceed the EPA standard. Ozone observations over the bay during the afternoon were consistently 10-20% higher than the closest upwind ground sites during the 10-day campaign; this pattern persisted during good and poor air quality days. A lower boundary layer, reduced cloud cover, slower dry deposition rates, and other lesser mechanisms, contribute to the local maximum of ozone over the Chesapeake Bay. Observations from this campaign were compared to a CMAQ simulation at 1.33 km resolution. The model is able to predict the regional maximum of ozone over the Chesapeake Bay accurately, but NOy concentrations are significantly overestimated. Explanations for the overestimation of NOy in the model simulations are also explored

boundary layer↗

NASA NTRS2001

Use of Human Modeling Simulation Software in the Task Analysis of the Environmental Control and Life Support System Component Installation Procedures

Virtual reality and simulation applications are becoming widespread in human task analysis. These programs have many benefits for the Human Factors Engineering field. Not only do creating and using virtual environments for human engineering analyses save money and time, this approach also promotes user experimentation and provides increased quality of analyses. This paper explains the human engineering task analysis performed on the Environmental Control and Life Support System (ECLSS) space station rack and its Distillation Assembly (DA) subsystem using EAI's human modeling simulation software, Jack. When installed on the International Space Station (ISS), ECLSS will provide the life and environment support needed to adequately sustain crew life. The DA is an Orbital Replaceable Unit (ORU) that provides means of wastewater (primarily urine from flight crew and experimental animals) reclamation. Jack was used to create a model of the weightless environment of the ISS Node 3, where the ECLSS is housed. Computer aided drawings of the ECLSS rack and DA system were also brought into the environment. Anthropometric models of a 95th percentile male and 5th percentile female were used to examine the human interfaces encountered during various ECLSS and DA tasks. The results of the task analyses were used in suggesting modifications to hardware and crew task procedures to improve accessibility, conserve crew time, and add convenience for the crew. This paper will address some of those suggested modifications and the method of presenting final analyses for requirements verification.

Estes, Samantha↗

DOE OSTI2023

MOOSE: A Modular Platform for Fission and Fusion Multiphysics

The Multiphysics Object-Oriented Simulation Environment (MOOSE) Framework, as well as MOOSE-based simulation tools, have accelerated the development of fission energy and advanced reactor technologies through the United States Department of Energy, Office of Nuclear Science, Nuclear Energy Advanced Modeling & Simulation (NEAMS) Program. MOOSE contains a complete platform of multiphysics simulation capabilities, capable of running on massively parallel systems, and is developed in an open-source manner with great attention paid to high-quality software quality assurance practices. This overall approach could greatly benefit the fusion energy community, which requires rapid design iteration and improvement in order to facilitate the successful development of fusion as an alternative energy source to fossil fuels. In the first half of this talk, applications of MOOSE and MOOSE-based tools for advanced reactor designs will be showcased, as well as MOOSE ecosystem infrastructure (such as the NEAMS Virtual Test Bed) that enables and accelerates fission reactor design. In the second half, a discussion of how the MOOSE approach to modeling and simulation is currently being applied internationally in fusion energy research and development at the United Kingdom Atomic Energy Authority will be discussed, and ongoing/future domestic research efforts will be highlighted.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗