Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scanning Electron Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Fabrication of chitosan/polyacrylonitrile blend and semi-IPN hydrogel with epichlorohydrin

The present study is focused on the preparation of chitosan (CS)/polyacrylonitrile (PAN) blend and semi-interpenetrating polymer network (sIPN). Blend CS/PAN hydrogel films (HFs) were prepared by solution blending and casting technique. CS in the blend was crosslinked with epichlorohydrin (ECH) to prepare sIPN. The developed CS/PAN blend and sIPN hydrogels were characterized with Field Emission Scanning Electron Microscopy (FE-SEM), Fourier transform infrared spectroscopy (FTIR), Thermagravimetric analysis (TGA), and Differential Scanning Calorimeter (DSC). The result showed good miscibility between CS and PAN and crosslinking of CS in the blend. The swelling of the different blended and sIPN hydrogels samples were examined at room temperature (T{sub r}). Blend (C80/P20) sample showed highest swelling (∼2400%) and fair degree of stability (∼28% until 96 h), whereas sIPN hydrogel exhibited relatively low degree of swelling (∼244%) and high degree of aqueous (∼85 % until 96 h), and thermal (onset temperature 304°C) stabilities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An ESEM investigation of latex film formation in cement pore solution

Environmental scanning electron microscopy (ESEM) and complementary methods were employed to study the time dependent film formation of a latex dispersion in water and cement pore solution. First, a model carboxylated styrene/n-butyl acrylate latex dispersion possessing a minimum film forming temperature (MFFT) of 18 {sup o}C was synthesized in aqueous media via emulsion polymerization. Its film forming property was at a temperature of 40 {sup o}C, studied under an ESEM. The analysis revealed that upon removal of water, film formation occurs as a result of particle packing, particle deformation and finally particle coalescence. Film formation is significantly retarded when the latex dispersion is present in cement pore solution. This effect can be ascribed to adsorption of Ca{sup 2+} ions onto the surface of the anionic latex particles and to interfacial secondary phases. This layer of adsorbed Ca{sup 2+} ions hinders interdiffusion of the macromolecules and subsequent film formation of the latex polymer.

36 MATERIALS SCIENCE↗

Polymer-directed synthesis and magnetic property of nanoparticles-assembled BiFeO{sub 3} microrods

Nanoparticles-assembled BiFeO{sub 3} microrods were successfully prepared via a polymer-directed solvothermal route. The phase and morphology of the products were characterized by powder X-ray diffraction (XRD), energy dispersive spectrometry (EDS), inductively coupled plasma atomic emission spectroscopy (ICP-AES), FT-IR spectroscopy and scanning electron microscopy (SEM). Experiments indicated that the linking effect originated from the interactions between polymer molecules could direct the self-assembly of building blocks into one-dimensional nanoparticles-assembled BiFeO{sub 3} microrods. Some factors influencing the morphologies of the products were systematically investigated and a possible mechanism of the formation of the microrods was suggested. Moreover, the magnetic properties of the products were studied. - Graphical abstract: Nanoparticles-assembled BiFeO{sub 3} microrods were successfully prepared via a polymer-directed solvothermal route and characterized by XRD, EDS, FT-IR, ICP-AES and SEM.

36 MATERIALS SCIENCE↗

A New Method for Qualitative Multi-scale Analysis of Bacterial Biofilms on Filamentous Fungal Colonies Using Confocal and Electron Microscopy

Bacterial biofilms frequently form on fungal surfaces and can be involved in numerous bacterial-fungal interaction processes, such as metabolic cooperation, competition, or predation. The study of biofilms is important in many biological fields, including environmental science, food production, and medicine. However, few studies have focused on such bacterial biofilms, partially due to the difficulty of investigating them. Most of the methods for qualitative and quantitative biofilm analyses described in the literature are only suitable for biofilms forming on abiotic surfaces or on homogeneous and thin biotic surfaces, such as a monolayer of epithelial cells. While laser scanning confocal microscopy (LSCM) is often used to analyze in situ and in vivo biofilms, this technology becomes very challenging when applied to bacterial biofilms on fungal hyphae, due to the thickness and the three dimensions of the hyphal networks. To overcome this shortcoming, we developed a protocol combining microscopy with a method to limit the accumulation of hyphal layers in fungal colonies. Using this method, we were able to investigate the development of bacterial biofilms on fungal hyphae at multiple scales using both LSCM and scanning electron microscopy (SEM). Furthermore, this report describes the protocol, including microorganism cultures, bacterial biofilm formation conditions, biofilm staining, and LSCM and SEM visualizations.

59 BASIC BIOLOGICAL SCIENCES↗

Dual acceptor doping and aging effect of p-ZnO:(Na, N) nanorod thin films by spray pyrolysis

An attempt has been made to realize p-type ZnO by dual acceptor doping (Na-N) into ZnO thin films. Na and N doped ZnO thin films of different concentrations (0 to 8 at.%) have been grown by spray pyrolysis at 623 K. The grown films on glass substrate have been characterized by X-ray diffraction (XRD), Hall measurement, UV-Vis spectrophotometer, Photoluminescence (PL) and Energy dispersive spectroscopy (EDS) to validate the p-type conduction. The surface morphology and roughness of the ZnO:(Na, N) films are studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. Hall measurement shows that all the films exhibit p-type conductivity except for 0 at.% Na-N doped ZnO film. The obtained resistivity (5.60×10{sup −2} Ω cm) and hole concentration (3.15×10{sup 18} cm{sup −3}) for the best dual acceptor doped film is 6 at.%. It has been predicted that (Na{sub Zn}−N{sub O}) acceptor complex is responsible for the p-type conduction. The p-type conductivity of the ZnO:(Na, N) films is stable even after 6 months. The crystallinity of the films has been studied by XRD. Energy dispersive spectroscopy (EDS) confirms the presence of Na and N in 6 at.% ZnO:(Na, N) film. Photoluminescence (PL) spectra of ZnO:(Na, N) films show NBE and deep level emissions in the UV and visible regions, respectively. The ZnO:(Na, N) films exhibit a high transmittance about 90% in the visible region.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis, structure and properties of Na[AsW{sub 2}O{sub 9}]

Single crystal and polycrystalline powder samples of sodium arseno-tungstate of composition Na[AsW{sub 2}O{sub 9}] were synthesized using high-temperature solid-state methods. The greenish single crystals of the phase were characterized by X-ray diffraction data structure determination and the bulk compound confirmed by powder X-ray data Rietveld refinements. Additionally, scanning electron microscopy (SEM) attached with energy dispersive X-Ray spectroscopy (EDX), thermogravimetry (TG), differential scanning calorimetry (DSC), fourier transform infrared (FTIR) and Raman spectroscopy was performed. A comparative study between Na[AsW{sub 2}O{sub 9}] and isotypic K[AsW{sub 2}O{sub 9}] demonstrates the structural modifications and the consequent properties. Placing sodium in the channel of the arseno-tungstate framework, the average As-O and W-O bond distances did not change due to their rigid-unit like behaviors. However, the unit cell volume contracted about 7.4% caused by shrinkage of the channel dimensions due to shorter Na-O bond distances. The non-linear optical property of the compound has been explained in terms of asymmetric W-O and As-O chemical bonding led by WO{sub 6} and AsO{sub 4} polyhedral distortion, respectively.

36 MATERIALS SCIENCE↗

Synergistic Effect of Graphene Oxide for Impeding the Dendritic Plating of Li

Dendritic growth of lithium (Li) has severely impeded the practical application of Li-metal batteries. Herein, a 3D conformal graphene oxide nanosheet (GOn) coating, confined into the woven structure of a glass fiber separator, is reported, which permits facile transport of Li-ions thought its structure, meanwhile regulating the Li deposition. Electrochemical measurements illustrate a remarkably enhanced cycle life and stability of the Li-metal anode, which is explained by various microscopy and modeling results. Utilizing scanning electron microscopy, focused ion beam, and optical imaging, the formation of an uniform Li film on the electrode surface in the case of GO-modified samples is revealed. Ab initio molecular dynamics (AIMD) simulations suggest that Li-ions initially get adsorbed to the lithiophilic GOn and then diffuse through defect sites. This delayed Li transfer eliminates the “tip effect” leading to a more homogeneous Li nucleation. Meanwhile, C-C bonds rupture observed in the GO during AIMD simulations creates more pathways for faster Li-ions transport. In addition, phase-field modeling demonstrates that mechanically rigid GOn coating with proper defect size (smaller than 25 nm) can physically block the anisotropic growth of Li. This new understanding is a significant step toward the employment of 2D materials for regulating the Li deposition

25 ENERGY STORAGE↗

Effect of Hot Isostatic Pressing and Powder Feedstock on Porosity, Microstructure, and Mechanical Properties of Selective Laser Melted AlSi10Mg

AlSi10Mg tensile bars were additively manufactured using the powder-bed selective laser melting process. Samples were subjected to stress relief annealing and hot isostatic pressing. Tensile samples built using fresh, stored, and reused powder feedstock were characterized for microstructure, porosity, and mechanical properties. Fresh powder exhibited the best mechanical properties and lowest porosity while stored and reused powder exhibited inferior mechanical properties and higher porosity. The microstructure of stress relieved samples was fine and exhibited (001) texture in the z-build direction. Microstructure for hot isostatic pressed samples was coarsened with fainter (001) texture. To investigate surface and interior defects, scanning electron microscopy, optical fractography, and laser scanning microscopy techniques were employed. Hot isostatic pressing eliminated internal pores and reduced the size of surface porosity associated with the selective laser melting process. Hot isostatic pressing tended to increase ductility at the expense of decreasing strength. Furthermore, scatter in ductility of hot isostatic pressed parts suggests that the presence of unclosed surface porosity facilitated fracture with crack propagation inward from the surface of the part.

36 MATERIALS SCIENCE↗

Crystallographic texture and microstructural changes in fusion welds of recrystallized Zry-4 rolled plates

This study presents a detailed characterization of the microstructural and crystallographic texture changes observed in the transition region in a weld between two Zircaloy-4 cold rolled and recrystallized plates. The microstructural study was performed by optical microscopy under polarized light and scanning electron microscopy (SEM). Texture changes were characterized at different lengthscales: in the micrometric size, orientation imaging maps (OIM) were constructed by electron backscatter diffraction (EBSD), in the millimetre scale, high energy XRD experiments were done at the Advanced Photon Source (USA) and compared to neutron diffraction texture determinations performed in the HIPPO instrument at Los Alamos National Laboratory. In the heat affected zone (HAZ) we observed the development of Widmanstätten microstructures, typical of the α( hcp ) to β( bcc ) phase transformation. Associated with these changes a rotation of the c-poles is found in the HAZ and fusion zone. While the base material shows the typical texture of a cold rolled plate, with their c-poles pointing 35° apart from the normal direction of the plate in the normal-transversal line, in the HAZ, c-poles align along the transversal direction of the plate and then re-orient along different directions, all of these changes occurring within a lengthscale in the order of mm. The evolution of texture in this narrow region was captured by both OIM and XRD, and is consistent with previous measurements done by Neutron Diffraction in the HIPPO diffractometer at Los Alamos National Laboratory, USA. The microstructural and texture changes along the HAZ were interpreted as arising due to the effect of differences in the cooling rate and β grain size on the progress of the different α variants during transformation. Fast cooling rates and large β grains are associated to weak variant selection during the β–>α transformation, while slow cooling rates and fine β grains result in strong variant selection.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Different Damp-Heat-Induced Series Resistance Degradation Behaviors in Fielded Crystalline Silicon Photovoltaic Modules Due to Difference in Bill of Materials

This case study investigates mono-crystalline silicon modules from underperforming portions of a utility-scale photovoltaic power plant. Field-collected I-V curves and electroluminescence imaging suggested that increased series resistance was a primary factor driving module degradation. Selected modules were removed from the field for further analysis, including incremental damp heat accelerated testing, which confirmed a progression in series resistance degradation. Two distinct cell degradation behaviors became apparent during the investigation. Cross-sectional scanning electron microscopy (with elemental analysis) and scanning spreading resistance microscopy identified key differences between the two degradation mechanisms, primarily grid finger width and contact resistance. Additionally, the study highlights the reliability implications of retest requirements in International Electrotechnical Commission 61215 for material changes and how they may have mitigated the degradation observed at this site.

14 SOLAR ENERGY↗

The survivability of phyllosilicates and carbonates impacting Stardust Al foils: Facilitating the search for cometary water

Abstract Comet 81P/Wild 2 samples returned by NASA's Stardust mission provide an unequalled opportunity to study the contents of, and hence conditions and processes operating on, comets. They can potentially validate contentious interpretations of cometary infrared spectra and in situ mass spectrometry data: specifically the identification of phyllosilicates and carbonates. However, Wild 2 dust was collected via impact into capture media at ~6 km s −1 , leading to uncertainty as to whether these minerals were captured intact, and, if subjected to alteration, whether they remain recognizable. We simulated Stardust Al foil capture conditions using a two‐stage light‐gas gun, and directly compared transmission electron microscope analyses of pre‐ and postimpact samples to investigate survivability of lizardite and cronstedtite (phyllosilicates) and calcite (carbonate). We find the phyllosilicates do not survive impact as intact crystalline materials but as moderately to highly vesiculated amorphous residues lining resultant impact craters, whose bulk cation to Si ratios remain close to that of the impacting grain. Closer inspection reveals variation in these elements on a submicron scale, where impact‐induced melting accompanied by reducing conditions (due to the production of oxygen scavenging molten Al from the target foils) has resulted in the production of native silicon and Fe‐ and Fe‐Si‐rich phases. In contrast, large areas of crystalline calcite are preserved within the calcite residue, with smaller regions of vesiculated, Al‐bearing calcic glass. Unambiguous identification of calcite impactors on Stardust Al foil is therefore possible, while phyllosilicate impactors may be inferred from vesiculated residues with appropriate bulk cation to Si ratios. Finally, we demonstrate that the characteristic textures and elemental distributions identifying phyllosilicates and carbonates by transmission electron microscopy can also be observed by state‐of‐the‐art scanning electron microscopy providing rapid, nondestructive initial mineral identifications in Stardust residues.

79 ASTRONOMY AND ASTROPHYSICS↗

Study of the I-V characteristics of nanostructured Pd films on a Si substrate after vacuum annealing

The I-V characteristics of nanostructured Pd films on a Si substrate are investigated. The nanostructures (nanoislands) are formed by the vacuum annealing of continuous ultrathin Pd films sputtered onto a substrate. The shape of the I-V characteristics of the investigated Si substrate-Pd film system is shown to be heavily dependent on the degree of film nanostructuring. The surface morphology of the films is studied using scanning electron microscopy.

36 MATERIALS SCIENCE↗

Designing an impedance-based technique for studying corrosion on cladding materials

In nuclear cladding materials, changes in structure and chemistry over the lifetime of claddings can have a significant impact on fuel and reactor performance. Currently, chemical evolution over the lifetime of the fuel and cladding materials can only be inferred using post-irradiation examination. As an alternative to post-irradiation measurements, electrochemical impedance spectroscopy (EIS) can provide an in-pile measurement of changes in chemistry in oxides and hydrides. The objective of this study is to develop an impedance based sensing technology for measuring spatial- and time-resolved in-pile changes in cladding chemistry in order to understand the mechanisms of hydride formation, hydride dealloying and associated cladding corrosion so that a mitigation strategy and technology can be developed for reactor safe operation. Two prototype impedance-based sensors were designed and assembled using Zr-4 as working electrode and Pt as counter and reference electrode. One sensor is tubular type and the other one is plate-type. These sensors will be tested in static autoclave to investigate the effects of various environmental conditions (including temperature, pressure, and water chemistry) on cladding material corrosion mechanisms. These in-situ EIS sensors would provide corrosion-layer parameters in high-temperature water, such as (1) total layer thickness, (2) the evolution of oxide structures as uniform layer dielectric or sublayer(s), and (3) the possible electrochemistry of the volume corrosion process and the solid/liquid interface, such as the cyclic nature of corrosion of Zr alloys in high-temperature water. This work was focused on electrochemical sensor development, targeting cladding oxides/hydrides under thermodynamic equilibria; characterization of samples using Kelvin probe force microscopy (SKPFM), Raman spectroscopy, and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS) to provide high-resolution co-localized characterization of zirconium oxide and metal/oxide interface.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantifying and Qualifying Alloys Based on Level of Homogenization: A U–10 wt% Mo Alloy Case Study

Homogenization heat treatment is performed to attain uniformity in microstructure of metals and metal alloys, which is helpful to achieve the desired workability and microstructure in final products, and eventually to gain predictable and consistent performance. Fabrication of fuel plates made from a low-enriched uranium alloy with 10 wt% Mo (U-10Mo) involves multiple thermomechanical processing steps. It is well known that the molybdenum homogeneity in the final formed product affects the fuel performance in the nuclear reactor. To make sure these materials are uniformly homogenized, a statistical method was proposed to quantify and characterize the Mo concentration variation in U-10Mo fuel plates by analyzing the Mo concentration measurement data from scanning electron microscopy–energy dispersive spectroscopy line scans. Statistical tolerance intervals were employed to determine the qualification of U-10Mo fuel plates. We formulate an argument for the minimum number of independent samples required to define fuel plate qualification if no Mo measurement data are available in advance, and demonstrate that the given tolerance interval requirements can be equivalently reduced to a sample variance criterion in this application. The outcome of the statistical analysis can be used to optimize casting design and eventually increase productivity and reduce fabrication cost. The statistical strategy developed in this report can be implemented for other applications, especially in the field of material manufacturing to assess qualification requirements and monitor and improve process design.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Taxonomy and Identification of Principal Foliar Nematode Species ( Aphelenchoides and Litylenchus )

Nematodes are Earth’s most numerous multicellular animals and include species that feed on bacteria, fungi, plants, insects, and animals. Foliar nematodes are mostly pathogens of ornamental crops in greenhouses, nurseries, forest trees, and field crops. Nematode identification has traditionally relied on morphological and anatomical characters using light microscopy and, in some cases, scanning electron microscopy (SEM). This review focuses on morphometrical and brief molecular details and key characteristics of some of the most widely distributed and economically important foliar nematodes that can aid in their identification. Aphelenchoides genus includes some of the most widely distributed nematodes that can cause crop damages and losses to agricultural, horticultural, and forestry crops. Morphological details of the most common species of Aphelenchoides (A. besseyi, A. bicaudatus, A. fragariae, A. ritzemabosi) are given with brief molecular details, including distribution, identification, conclusion, and future directions, as well as an updated list of the nominal species with its synonyms. Litylenchus is a relatively new genus described in 2011 and includes two species and one subspecies. Species included in the Litylenchus are important emerging foliar pathogens parasitizing trees and bushes, especially beech trees in the United States of America. Brief morphological details of all Litylenchus species are provided.

54 ENVIRONMENTAL SCIENCES↗

The atomic nature of polymer-metal interactions in adhesion, friction and wear

The adhesion, friction, and wear behavior of the solid polymers PTFE and polyimide in contact with various metals were studied using field ion microscopy, Auger emission spectroscopy, and scanning electron microscopy. Results indicate that the polymers will transfer to a clean tungsten surface on simple tough contact, forming a chemical bond. With PTFE, it is hypothesized that the bonding is of the carbon to the metal surface, while with the polyimide, both oxygen and carbon bonding to the tungsten surface are possible. In sliding contact, the friction process itself can initiate polymer film formation. The formation of such films has been suggested as a form of extreme pressure lubrication.

Buckley, D. H.↗

Structure and properties of solid surfaces

Difficulties in experimental studies of crystalline surfaces are related to the fact that surface atoms have an intrinsic tendency to react with their environment. A second problem is connected with the effective thickness of surfaces, which ranges from one to several atom layers. The phenomenology of surface interactions with gases are considered, taking into account physical adsorption, chemisorption, and the oxidation of surfaces. Studies of the surface structure are discussed, giving attention to field emission microscopy, field-ion microscopy, electron diffraction techniques, Auger spectroscopy, scanning electron microscopy, electron probe microanalysis, ion microprobe methods, and low-energy backscattering spectroscopy. Investigations of semiconductor surfaces are also described.

Gatos, H. C.↗

Hot Hydrogen Testing of Refractory Metals and Ceramics

The objective of this investigation is to develop a technique with which refractory metal carbide samples can be exposed to hydrogen containing gases at high temperatures, and to use various microstructural and analytical techniques to determine the chemical and rate processes involved in hydrogen degradation in these materials. Five types of carbides were examined including WC, NbC, HfC, ZrC, and TaC. The ceramics were purchased and were all monolithic in nature. The temperature range investigated was from 850 to 1600 C with a hydrogen pressure of one atmosphere. Control experiments, in vacuum, were also conducted for comparison so that the net effects due to hydrogen could be isolated. The samples were analyzed prior to and after exposure. Gas samples were collected in selected experiments and analyzed using gas chromography. Characterization of the resulting microstructure after exposure to hydrogen was conducted using optical microscopy, x-ray diffraction, scanning electron microscopy, and weight change. The ceramics were purchased and were all monolithic in nature. It was found that all samples lost weight after exposure, both in hydrogen and vacuum. Results from the microstructure analyses show that the degradation processes are different among the five types of ceramics involved. In addition, the apparent activation energy for the degradation process is a function of temperature even within the same material. This indicates that there are more than one mechanism involved in each material, and that the mechanisms are temperature dependent.

Zee, Ralph↗