Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Flight test evaluation of predicted light aircraft drag, performance, and stability

A technique was developed which permits simultaneous extraction of complete lift, drag, and thrust power curves from time histories of a single aircraft maneuver such as a pullup (from V sub max to V sub stall) and pushover (to sub V max for level flight.) The technique is an extension to non-linear equations of motion of the parameter identification methods of lliff and Taylor and includes provisions for internal data compatibility improvement as well. The technique was show to be capable of correcting random errors in the most sensitive data channel and yielding highly accurate results. This technique was applied to flight data taken on the ATLIT aircraft. The drag and power values obtained from the initial least squares estimate are about 15% less than the 'true' values. If one takes into account the rather dirty wing and fuselage existing at the time of the tests, however, the predictions are reasonably accurate. The steady state lift measurements agree well with the extracted values only for small values of alpha. The predicted value of the lift at alpha = 0 is about 33% below that found in steady state tests while the predicted lift slope is 13% below the steady state value.

Smetana, F. O.↗

Effect of casing treatment on performance of a two-stage high-pressure-ratio fan

A two-stage fan, previously tested with a solid casing, was tested with a casing with circumferential grooves over the tips of both rotors (casing treatment). Tests were conducted at 80 and 100 percent of design speed with uniform flow. The casing treatment improved the flow range and stall margin significantly without changing the characteristics overall performance curves of total-pressure and efficiency as functions of weight flow, other than extending them to lower weight flows.

Urasek, D. C.↗

Characteristics of aeroelastic instabilities in turbomachinery - NASA full scale engine test results

Several aeromechanical programs were conducted in the NASA/USAF Joint Engine System Research Programs. The scope of these programs, the instrumentation, data acquisition and reduction, and the test results are discussed. Data pertinent to four different instabilities were acquired; two types of stall flutter, choke flutter and a system mode instability. The data indicates that each instability has its own unique characteristics. These characteristics are described.

Lubomski, J. F.↗

Application of the AMI C sub l sub max prediction method to a number of airfoils

A method for calculating the flow about airfoils up to and beyond the stall is described. It is an iterative procedure between potential flow and boundary layer solutions. The separated region is modeled in the potential flow analysis using free vortex sheets which require an inner iteration to establish their shapes. The free vortex sheet length is an important parameter in the potential flow calculation. Results so far indicate a possible correlation between wake length and airfoil thickness/chord ratio. Calculated and experimental results are compared for a series of airfoils.

Dvorak, F. A.↗

Simulation study to evaluate a constant-groundspeed approach method in moderate and severe wind shears

The use of a constant-groundspeed procedure for flying final approaches in moderate and severe wind shear environments was investigated. Performance was compared to results of simulated constant-airspeed approaches in identical wind profiles. The simulation model was a medium twin-jet transport equipped with an autothrottle for maintaining constant groundspeed or constant airspeed. For both moderate and severe wind shears, the constant-groundspeed approach method was shown to provide a way to more safely negotiate the shears while also providing predictable and acceptable touchdown performance. Results showed airspeeds on final approach to be considerably higher using the constant-groundspeed method, which supplied the additional stall margin needed when tail-wind shears were encountered. Throttle movements were noticeably reduced in all wind profiles when constant-groundspeed approaches were flown. Touchdown conditions were practically identical for both approach methods in moderate wind shear.

Kelley, W. W.↗

The influence of sweep on the aerodynamic loading of an oscillating NACA 0012 airfoil. Volume 1: Technical report

Aerodynamic experiments were performed on an oscillating NACA 0012 airfoil utilizing a tunnel-spanning wing in both unswept and 30 degree swept configurations. The airfoil was tested in steady state and in oscillatory pitch about the quarter chord. The unsteady aerodynamic loading was measured using pressure transducers along the chord. Numerical integrations of the unsteady pressure transducer responses were used to compute the normal force, chord force, and moment components of the induced loading. The effects of sweep on the induced aerodynamic load response was examined. For the range of parameters tested, it was found that sweeping the airfoil tends to delay the onset of dynamic stall. Sweeping was also found to reduce the magnitude of the unsteady load variation about the mean response. It was determined that at mean incidence angles greater than 9 degrees, sweep tends to reduce the stability margin of the NACA 0012 airfoil; however, for all cases tested, the airfoil was found to be stable in pure pitch. Turbulent eddies were found to convect downstream above the upper surface and generate forward-moving acoustic waves at the trailing edge which move upstream along the lower surface.

St.hilaire, A. O.↗

A study of the drooped leading edge airfoil

Wind tunnel tests were conducted to examine various aspects of the drooped-leading edge airfoil which reduces the tendency for an airplane to enter a spin after stall occurs. Three baseline models were used for tests of two dimensional models: NACA 0015, 0014.6, and 0014.2. The 14.6% and 14.2% models were derived from NACA 0015 sections by increasing the chord and matching the profiles aft section. Force, balance data (lift, drag, pitching moment) were obtained for each model at a free-steam Reynold's number of 2.66 x 10 to the 6th power/m. In addition, oil flow visualization tests were performed at various angles of attack. An existing NACA 64 sub 1 A211 airfoil was used in a second series of tests. The leading edge flap was segmented in three parts which allowed various baseline/drooped leading edge configurations to be tested. Force balance and flow visualization tests were completer at chord Renolds numbers of 0.44 x 10 to the 6th power, 1.4 x 10 to the 6th power, and 2.11 x 10 to the 6th power. Test results are included.

Anderson, J. D., Jr.↗

Upper-surface modifications for C sub l max improvement of selected NASA 6-series airfoils

The thickness of the upper surface of 64 airfoils was increased from the leading edge to the position of maximum thickness. The modifications were generated using a numerical optimization routine coupled with an aerodynamic analysis code. The type of modification presented can be used for aircraft design or for the retrofit of current aircraft to improve the stall characteristics and climb performance. The coordinates of the modified airfoils are presented with plots of the forward 45% of the profiles and pressure distributions for both the modified and unmodified sections at an angle of attack of 14 degrees.

Szelazek, C. A.↗

Performance of two-stage fan with a first-stage rotor redesigned to account for the presence of a part-span damper

The NASA two-stage fan was tested with a redesigned first-stage rotor. The redesign included a new design approach to account for the presence of a part-span damper. At design speed the fan achieved a peak efficiency of 0.803, which is 1.9 percentage points higher than the original design. The peak efficiencies of the first stage and first rotor were 0.789 and 0.821, respectively. An improvement in efficiency of up to 5 percentage points in the damper region was achieved over the original large damper version. The stall margin, based on flow conditions at peak efficiency, was 10 percent at design speed.

Gorrell, W. T.↗

Overview of NASA aerial applications research

Aerial applications research conducted by NASA seeks improvements in environmental safety, fuel efficiency, and aircraft productivity and safety. From 1976 to 1978, NASA studied the technology needs of the aerial applications industry and developed in-house research capabilities for meeting those needs. This paper presents the research plans developed by NASA. High potential appears to exist for near term contributions to the industry from existing NASA research capabilities in drift reduction, stall departure safety, and dry materials dispersal system technology. A brief, annotated bibliography is included listing documents recently produced as a result of NASA aerial applications research efforts.

Holmes, B. J.↗

Transonic flow about a two-dimensional airfoil inviscid and turbulent flow properties.

Flow-field measurements are presented for a symmetrical NACA 64A010 airfoil section at transonic conditions. Measurements were obtained for three angles of attack with the free-stream Mach number fixed at 0.8. The cases studied included a weak shock wave/boundary layer interaction, an interaction of medium strength with mild separation, and an interaction of sufficient strength to produce a shock-induced stall situation. Two nonintrusive optical techniques, laser velocimetry and holographic interferometry, were used to characterize the flows. The results include Mach number contours and flow angle distributions in the inviscid flow regions, and turbulent flow properties, including the turbulent Reynolds stresses, of the upper surface viscous layers, and of the near-wake. The turbulent flow measurements reveal that the turbulence fluctuations attain equilibrium with the local mean flow much faster than previously expected.

Johnson, D. A.↗

Characteristics of aeroelastic instabilities in turbomachinery - NASA full scale engine test results

Several aeromechanical programs have been conducted in the NASA/USAF Joint Engine System Research Programs. The scope of these programs, the instrumentation, data acquisition and reduction, and the test results are discussed. Data pertinent to four different instabilities were acquired; two types of stall flutter, choke flutter and a system mode instability. The data indicates that each instability has its own unique characteristics. These characteristics are described.

Lubomski, J. F.↗

Control considerations for CCV fighters at high angles of attack

Wind tunnel and piloted simulation studies show that the use of the CCV concept of relaxed static pitch stability on fighter aircraft at high angles of attack can result in pitch departures caused by inertia and/or kinematic coupling and in deep stall trim. These problems can be avoided by sufficient nose-down pitch control at high attack angles, and effectiveness of several pitch control configurations such as aft-mounted stabilators, canard mounted flaps, and all-movable canards was investigated. A variable incidence canard with a large travel range was the most effective means of obtaining the required pitch control, although very large deflections may be required on highly unstable configurations. Control laws were developed for cases where the high angle of pitch control requirement is not met, but they can limit aircraft roll capability and thus compromise maneuverability.

Nguyen, L. T.↗

Some observations on the mechanism of aircraft wing rock

A scale model of the Northrop F-5A was tested in NASA Ames Research Center Eleven-Foot Transonic Tunnel to simulate the wing rock oscillations in a transonic maneuver. For this purpose, a flexible model support device was designed and fabricated, which allowed the model to oscillate in roll at the scaled wing rock frequency. Two tunnel entries were performed to acquire the pressure (steady state and fluctuating) and response data when the model was held fixed and when it was excited by flow to oscillate in roll. Based on these data, a limit cycle mechanism was identified, which supplied energy to the aircraft model and caused the Dutch roll type oscillations, commonly called wing rock. The major origin of the fluctuating pressures that contributed to the limit cycle was traced to the wing surface leading edge stall and the subsequent lift recovery. For typical wing rock oscillations, the energy balance between the pressure work input and the energy consumed by the model's aerodynamic and mechanical damping was formulated and numerical data presented.

Hwang, C.↗

Split-film anemometer measurements on an airfoil with turbulent separated flow

Experimental studies of turbulent separation on airfoils have been conducted to aid in improving theoretical models of post-stall airfoil behavior. The studies utilize a variety of pressure and hot-film probes. The split-film anemometer has proved particularly valuable for measurement of highly turbulent reversing flows. Suggested techniques for on-line digital computer processing of the data are discussed.

Wentz, W. H., Jr.↗

Exploratory study of the influence of wing leading-edge modifications on the spin characteristics of a low-wing single-engine general aviation airplane

A wide variety of model and airplane tests were conducted to explore the effects of wing leading-edge modifications on the stalling and spinning characteristics of a low-wing general aviation research airplane configuration. The results presented herein discuss the effects of leading-edge airfoil modifications applied to the full wing span and to partial-span locations. The results obtained in the study indicate that the wing modifications can produce large effects (both favorable or unfavorable) on spin resistance, developed spin characteristics, and spin recovery.

Dicarlo, D. J.↗

LDV measurements on propellers

Laser Doppler velocimeter (LDV) measurements of the flow velocity around high-efficiency propeller blades for high disk loading turboprop propulsion systems are reported. The wind-tunnel flow around sets of eight straight and swept propeller blades with the same twist and chord distributions was measured using a conventional two-color dual scatter LDV system. The measurements of the axial flow velocities a small distance in front of the propeller blade, between the blade row, and downstream of the propeller are shown to provide information necessary for the determination of overall performance, swirl angle distribution, blade loading distributions, local lift and drag coefficients, interference effects, shock location, local induced velocities, wake characteristics and stall pattern.

Sullivan, J. P.↗

Characteristics of an Air Cushion Landing System incorporating an inelastic trunk

A series of static and dynamic tests performed on an Air Cushion Landing System (ACLS) incorporating inelastic trunk are described. The tests were performed on an apparatus which had provisions to isolate heave-pitch and roll motion on the prototype cushion. The results of the test show that the sides of the trunk behave differently from the trunk ends. The tests also demonstrate that the current ACLS designs suffer from low heave damping, low roll stiffness and fan stall problems.

Boghani, A. B.↗