Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SCALE MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Hybrid Models of Reactive Transport in Porous and Fractured Media

Darcy-scale models of flow and transport in porous media often fail to describe experimentally observed phenomena, while their pore-scale counterparts are accu- rate but can be computationally prohibitive. Most numerical multi-scale models, which seek to combine these two descriptions, require empirical closures and/or assumptions on the behavior of pore-scale quantities at the continuum (Darcy) scale. We present a general formulation of an iterative hybrid numerical method that links these two scales without resorting to such approximations. The algorithm treats the fluxes exchanged at the internal boundaries between the pore- and continuum-scale domains as unknown, and allows for iteratively determined boundary conditions to be applied at the pore-scale in order to guarantee their continuity. While the algorithm proposed is general, we use it to model Taylor dispersion in a fracture with chemically reactive walls. Results show significant improvement upon standard continuum-scale formulations.

54 ENVIRONMENTAL SCIENCES↗

An Urban Drainage Scheme for Large-Scale Flood Models

As flood modeling spatial resolutions get finer, physical processes normally neglected, such as urban drainage, must be accounted for. Here, we describe and evaluate an urban drainage scheme for large-scale flood models. The parameterization accounts for urban imperviousness, and water flow over streets and through a prescribed urban drainage network. A parameter sensitivity analysis is performed during three major extreme floods over Rio de Janeiro city, Brazil, at ∼200 m spatial resolution. Results show that, compared to a hypothetical case without urban drainage, representing a drainage network decreases urban flooding during selected extreme events across Rio de Janeiro by 31–53 %. Such a decrease is caused by an underground water storage of up to 2.5 billion m3 across the city during flood peaks. Underground water storage and transport smooth out and delay peak flows by a few hours over major rivers and channels draining the city. Simulations also indicate that the number of residents exposed to flooding drops by 60–80 %, from ∼5 million to 1–2 million, when an urban drainage system is considered during extreme events. Similar proportions are found for social infrastructure (i.e., schools and hospitals) exposed to flooding. Results reveal that racial minority and low-income populations could disproportionally be exposed to extreme floodings across the city. We conclude that representing urban drainage has a substantial impact on flood exposure and should be accounted for in fine resolution modeling. The proposed scheme is particularly useful in poorly monitored cities and where extreme floods are a frequent hazard yet to be tackled.

Urban drainage↗

A Small-Scale Tiltrotor Model Operating in Descending Flight

As a rotor s descent velocity in low speed flight approaches the induced wake velocity, a vortex ring is formed around the circumference of the rotor disk causing the flow to become very unsteady. This condition is known as Vortex Ring State (VRS). The aerodynamic Characteristics of edgewise operating rotors in this VRS induced environment have been studied for many years. In the 1960 s, two propellers were tested in vertical or near vertical descent, indicating a loss in thrust in the region of VRS. Thrust fluctuations of both single and tandem rotor configurations while operating in VRS were reported. More recently, the effects of descending flight on a single rotor operating in close proximity to a physical image plane, simulating the effects of a twin rotor tiltrotor system were investigated. Mean rotor thrust reductions and thrust fluctuations were shown in VRS. Results indicated the need to acquire additional data with a two-rotor model and the need to investigate the use of a single rotor/image plane apparatus to identify the characteristics of a two-rotor flowfield. As a result a small-scale tiltrotor model with 2-b1adedy untwisted, teetering rotors was tested at various states of descent and sideslip. Dual-rotor, single-rotor with image plane, and isolated-rotor results were reported, suggesting the single-rotor with image plane configuration may not properly capture the aerodynamic nature of a dual-rotor vehicle. Recommendations included additional testing of a model that better represents the physical characteristics of a tiltrotor aircraft. Specific recommendations for model improvements included using three-bladed rotors, twisted blades, a tiltrotor fuselage and wings.

Abrego, Anita I.↗

Vibration analysis of a 1/15 scale dynamic model of a space shuttle configuration

The natural frequencies and mode shapes of a 1/15 scale space shuttle dynamics model are analytically determined. The model, a parallel beam type structure with delta wings, is dynamically representative of the stiffness and mass properties of an early space shuttle design. Important characteristics of the model are elastic interfaces with adjustable spring rates. Normal mode computations are made using the finite element modeling technique as implemented in the NASTRAN (NASA Structural Analysis) computer program. The feasibility of neglecting elastic deformations in the lower modes was investigated using a rigid body model. Using NASTRAN, natural frequencies and mode shapes were first calculated for the booster fuselage, orbiter fuselage, and both delta wings in a free-free condition. Next, the fuselages were connected for various spring rates. Then the wings were attached to each fuselage, and the booster and orbiter were analyzed as separate airplanes. Finally, the two airplanes were elastically joined, and the complete model was analyzed.

Thornton, E. A.↗

Effect of a semi-annular thermal acoustic shield on jet exhaust noise

The effect of a semi-annular acoustic shield on jet exhaust noise is investigated with the rationale that such a configuration would reduce or eliminate the multiple reflection mechanism. A limited range of flow conditions for one nozzle/shield configuration were studied at model scale. Noise measurements for a 10 cm conical nozzle with a semi-annular acoustical shield are presented in terms of lossless free field data at various angular locations with respect to the nozzle. Measurements were made on both the shielded and unshielded sides of the nozzle. Model scale overall sound pressure level directivity patterns and comparisons of model scale spectral data are provided. The results show that a semi-annular thermal acoustic shield consisting of a low velocity, high temperature gas stream partially surrounding a central jet exhibits lower noise levels than when the central jet is operated alone. The results are presented parametrically, showing the effects of various shield and central system velocities and temperatures.

Goodykoontz, J.↗

The Numerical Analysis of a Turbulent Compressible Jet

A numerical method to simulate high Reynolds number jet flows was formulated and applied to gain a better understanding of the flow physics. Large-eddy simulation was chosen as the most promising approach to model the turbulent structures due to its compromise between accuracy and computational expense. The filtered Navier-Stokes equations were developed including a total energy form of the energy equation. Subgrid scale models for the momentum and energy equations were adapted from compressible forms of Smagorinsky's original model. The effect of using disparate temporal and spatial accuracy in a numerical scheme was discovered through one-dimensional model problems and a new uniformly fourth-order accurate numerical method was developed. Results from two- and three-dimensional validation exercises show that the code accurately reproduces both viscous and inviscid flows. Numerous axisymmetric jet simulations were performed to investigate the effect of grid resolution, numerical scheme, exit boundary conditions and subgrid scale modeling on the solution and the results were used to guide the three-dimensional calculations. Three-dimensional calculations of a Mach 1.4 jet showed that this LES simulation accurately captures the physics of the turbulent flow. The agreement with experimental data was relatively good and is much better than results in the current literature. Turbulent intensities indicate that the turbulent structures at this level of modeling are not isotropic and this information could lend itself to the development of improved subgrid scale models for LES and turbulence models for RANS simulations. A two point correlation technique was used to quantify the turbulent structures. Two point space correlations were used to obtain a measure of the integral length scale, which proved to be approximately 1/2 D(sub j). Two point space-time correlations were used to obtain the convection velocity for the turbulent structures. This velocity ranged from 0.57 to 0.71 U(sub j).

DeBonis, James R.↗

Improving the particle dry deposition scheme in the CMAQ photochemical modeling system

Dry deposition of atmospheric aerosols in large-scale models is a critical, but highly uncertain, sink process with a strong dependence on particle size, meteorological conditions, and land surface properties. This study investigates the particle dry deposition scheme implemented in the standard Community Multiscale Air Quality (CMAQ) model v5.2.1, characterizes its underlying parameterized components with comparison to a similar scheme in a contemporary regional-scale model, and proposes two updated schemes that are then evaluated with available ambient particle deposition velocity (V d ) measurements. Both updated schemes reduce the surprisingly strong dependence of deposition velocity on the aerosol mode width, with one scheme further introducing a dependence on vegetation coverage that is broadly consistent with variability in observations between vegetated and non-vegetated surfaces. Compared to the base scheme, the updated scheme with vegetation dependence increases V d for submicron particles and decreases it for larger particles by an average of 37% and –66%, respectively. This scheme performs statistically better than the base scheme, reducing fractional biases by 56%–97% for vegetated land-use types and has roughly equivalent performance over water. The base and updated schemes are tested with three annual CMAQ (v5.2.1) simulations for the year 2011; predicted ambient aerosol concentrations are evaluated with routine monitoring network observations and predicted dry deposition fluxes are evaluated with data from the Clean Air Status and Trends Network (CASTNET). The updated scheme with vegetation dependence reduces negative fractional biases for PM 10 by 41% and positive fractional biases for PM 2.5 organic carbon by 15%. This scheme has been incorporated into the most recent publicly accessible versions of CMAQ (v5.3 and beyond) to replace the scheme used in previous versions of CMAQ (v4.5 through v5.2.1).

54 ENVIRONMENTAL SCIENCES↗

Manifold learning for coarse-graining atomistic simulations: Application to amorphous solids

In this work, we introduce a generalized machine learning framework to probabilistically parameterize upper-scale models in the form of nonlinear PDEs consistent with a continuum theory, based on coarse-grained atomistic simulation data of mechanical deformation and flow processes. The proposed framework utilizes a hypothesized coarse-graining methodology with manifold learning and surrogate-based optimization techniques. Coarse-grained high-dimensional data describing quantities of interest of the multiscale models are projected onto a nonlinear manifold whose geometric and topological structure is exploited for measuring behavioral discrepancies in the form of manifold distances. A surrogate model is constructed using Gaussian process regression to identify a mapping between stochastic parameters and distances. Derivative-free optimization is employed to adaptively identify a unique set of parameters of the upper-scale model capable of rapidly reproducing the system's behavior while maintaining consistency with coarse-grained atomic-level simulations. The proposed method is applied to learn the parameters of the shear transformation zone (STZ) theory of plasticity that describes plastic deformation in amorphous solids as well as coarse-graining parameters needed to translate between atomistic and continuum representations. We show that the methodology is able to successfully link coarse-grained microscale simulations to macroscale observables and achieve a high-level of parity between the models across scales.

36 MATERIALS SCIENCE↗

Aerodynamic roughness measured in the field and simulated in a wind tunnel

This study evaluates how well values of aerodynamic surface roughness, z sub 0, measured over scale models in wind tunnels correlate with values of z sub 0 measured at full scale in the field. A field experiment was conducted in which values of z sub 0 and u* (wind friction speed) were measured over three arrays of non-erodible roughness elements on a dry lake bed. Wind profiles were measured by ten anemometers on a 15 m mast under thermally neutral atmospheric conditions. Values of z sub 0 increased from .00014 m (dry lake bed only) to .026 m with increasing roughness element density. The three roughness element arrays were simulated at 1/10 and 1/20 scale in an open-circuit atmospheric boundary-layer wind tunnel. Velocities were measured with a boundary-layer pitot-tube rake from the same relative position within the scale model arrays as the anemometers were relative to the field arrays. Each array at each scale was sampled three times at five freestream velocities. Average values of z sub 0 for each model array at each scale were compared with full-scale values of z sub 0 obtained in the field. The field vs. wind tunnel correspondence of z sub 0 is found to be z sub 0 field = 0.2661 x (z sub(0 model) x scale(exp -1))exp .8159.

Sullivan, Robert↗

What is the effect of LiDAR-derived DEM resolution on large-scale watershed model results?

This paper examines the effect of raster cell size on hydrographic feature extraction and hydrological modeling using LiDAR derived DEMs. LiDAR datasets for three experimental watersheds were converted to DEMs at various cell sizes. Watershed boundaries and stream networks were delineated from each DEM and were compared to reference data. Hydrological simulations were conducted and the outputs were compared. Smaller cell size DEMs consistently resulted in less difference between DEM-delineated features and reference data. However, minor differences been found between streamflow simulations resulted for a lumped watershed model run at daily simulations aggregated at an annual average. These findings indicate that while higher resolution DEM grids may result in more accurate representation of terrain characteristics, such variations do not necessarily improve watershed scale simulation modeling. Hence the additional expense of generating high resolution DEM's for the purpose of watershed modeling at daily or longer time steps may not be warranted.

99 GENERAL AND MISCELLANEOUS↗

Airframe noise prediction evaluation

The objective of this study is to evaluate the accuracy and adequacy of current airframe noise prediction methods using available airframe noise measurements from tests of a narrow body transport (DC-9) and a wide body transport (DC-10) in addition to scale model test data. General features of the airframe noise from these aircraft and models are outlined. The results of the assessment of two airframe prediction methods, Fink's and Munson's methods, against flight test data of these aircraft and scale model wind tunnel test data are presented. These methods were extensively evaluated against measured data from several configurations including clean, slat deployed, landing gear-deployed, flap deployed, and landing configurations of both DC-9 and DC-10. They were also assessed against a limited number of configurations of scale models. The evaluation was conducted in terms of overall sound pressure level (OASPL), tone corrected perceived noise level (PNLT), and one-third-octave band sound pressure level (SPL).

Yamamoto, Kingo J.↗

Lunar crane system

In many lunar construction scenarios, mechanical cranes in some form will be indispensible in moving large masses around with various degrees of fine positioning. While thorough experience exists in the use of terrestrial cranes new thinking is required about the design of cranes to be used in extraterrestrial construction. The primary driving force for this new thinking is the need to automate the crane system so that space cranes can be operated as telerobotic machines with a large number of automatic capabilities. This is true because in extraterrestrial construction human resources will need to be critically rationed. The design problems of mechanisms and control systems for a lunar crane must deal with at least two areas of performance. First, the automated crane must be capable of maneuvering a large mass, so that when the mass arrives at the target position there are only small vibrations. Secondly, any residue vibrations must be automatically damped out and a fine positioning must be achieved. For extraterrestrial use there are additional challenges to a crane design - for example, to design a crane system so that it can be transformed for other construction uses. This initial project in crane design does not address such additional issues, although they may be the subject of future CSC research. To date the Center has designed and analyzed many mechanisms. The fundamental problem of trade-offs between passively stabilizing the load and actively controlling the load by actuators was extensively studied. The capability of 3D dynamics modeling now exists for such studies. A scaled model of a lunar crane was set up and it has been most fruitful in providing basic understanding of lunar cranes. Due to an interesting scaling match-up, this scaled model exhibits the load vibration frequencies one would expect in the real lunar case. Using the analytical results achieved to date, a laboratory crane system is now being developed as a test bed for verifying a wide variety of mechanisms and control designs. Future development will be aimed at making the crane system a telerobotic test bed into which external sensors such as computer vision systems, and other small robotic devices such as CSC lunar rovers, will be integrated.

Mikulas, Martin M., Jr.↗

Capturing the response of Clostridium acetobutylicum to chemical stressors using a regulated genome-scale metabolic model

Clostridia are anaerobic Gram-positive Firmicutes containing broad and flexible systems for substrate utilization, which have been used successfully to produce a range of industrial compounds. Clostridium acetobutylicum has been used to produce butanol on an industrial scale through acetone-butanol-ethanol (ABE) fermentation. A genome-scale metabolic (GSM) model is a powerful tool for understanding the metabolic capacities of an organism and developing metabolic engineering strategies for strain development. The integration of stress related specific transcriptomics information with the GSM model provides opportunities for elucidating the focal points of regulation.

59 BASIC BIOLOGICAL SCIENCES↗

A priori analysis of a power-law sub-filter scale mixing model for transported PDF modeling of high Karlovitz turbulent premixed flames

Accurate modeling of mixing in large-eddy simulation (LES) / transported probability density function (PDF) modeling of turbulent combustion remains an outstanding issue. The issue is particularly salient in turbulent premixed combustion under extreme conditions such as high-Karlovitz number Ka. Here, the present study addresses this issue by conducting an a priori analysis of a power-law scaling based mixing timescale model for the transported PDF model. A recently produced DNS dataset of a high-Ka turbulent jet flame is used for the analysis. A power-law scaling is observed for a scaling factor used to model the sub-filter scale mixing timescale in this high-Ka turbulent premixed DNS flame when the LES filter size is much greater than the characteristic thermal thickness of a laminar premixed flame. The sensitivity of the observed power-law scaling to the different viewpoints (local or global) and to the different scalars for the data analysis is examined and the dependence of the model parameters on the dimensionless numbers Ka and Re (the Reynolds number) is investigated. Different model formulations for the mixing timescale are then constructed and assessed in the DNS flame. The proposed model is found to be able to reproduce the mixing timescale informed by the high-Ka DNS flame significantly better than a previous model.

42 ENGINEERING↗

Demonstration of in-Situ Resource Utilization of Lunar Regolith for Plant Growing Systems Through Scaled Capillary Models

The development of reliable and bioregenerative crop growth production systems is vital for human exploration into deep space. As the National Aeronautics and Space Administration (NASA) prepares for the Artemis missions, scientists need to find a way to provide consistent and sufficient water delivery for all stages of a plant’s life cycle. NASA has been able to successfully model passive flow through felt material, to mimic the water uptake and transport through a plant, in microgravity. However, more studies need to be conducted to adapt the model for a substrate-based system and incorporate how flow will change during each stage of plant growth. For future missions, payload requirements to support crop production systems will need to be limited, leading to the use of available resources, such as lunar regolith. Although numerous lunar regolith simulants are commercially available, few have been evaluated for their suitability in agricultural applications. First, a base regolith simulant will need to be identified based on its physical and chemical properties. Then, additional amendments to improve the properties of the simulants to support plant growth will be identified. The design and composition of the substrate will be based on water transport requirements for different stages of plant growth. Scaled capillary models can be utilized to study surface-tension driven flows through various designer substrates to modify the physical properties of the selected regolith simulant. These models can accurately represent how flow will act in a reduced gravity environment, which can be used to design a full-scale facility for surface missions. This project will aid space researchers in the design of future crop production systems for surface missions by creating a refined model that can be used at all stages of plant growth and utilize in situ resources.

Fluids↗

Small Scale WEC Performance Modeling Data

Small Scale WEC Performance Modeling Data is performance data from downscaled models of common WEC devices and their calculated performance outputs. This data is used by the Small WEC interactive modeling tool hosted by PRIMRE. The devices include a point absorber, a two-body point absorber (RM3), an oscillating surge device (OSWEC), and an attenuator type device (McCabe Wave Pump). One of the primary use cases for this work is to give an easy way to compare power output for a variety of WECs and model sizes.

16 TIDAL AND WAVE POWER↗

Multi-scale computational modeling of residual stress in selective laser melting with uncertainty quantification

Selective laser melting (SLM) is a powder-based additive manufacturing technique which creates parts by fusing together successive layers of powder with a laser. The quality of produced parts is highly dependent on the proper selection of processing parameters, requiring significant testing and experimentation to determine parameters for a given machine and material. Computational modeling could potentially be used to shorten this process by identifying parameters through simulation. However, simulating complete SLM builds is challenging due to the difference in scale between the size of the particles and laser used in the build and the size of the part produced. Often, continuum models are employed which approximate the powder as a continuous medium to avoid the need to model powder particles individually. While computationally expedient, continuum models require as inputs effective material properties for the powder which are often difficult to obtain experimentally. Building on previous works which have developed methods for estimating these effective properties along with their uncertainties through the use of detailed models, this work presents a part scale continuum model capable of predicting residual thermal stresses in an SLM build with uncertainty estimates. Model predictions are compared to experimental measurements from the literature.

42 ENGINEERING↗

Integration of genome-scale metabolic model with biorefinery process model reveals market-competitive carbon-negative sustainable aviation fuel utilizing microbial cell mass lipids and biogenic CO 2

Producing scalable, economically viable, low-carbon biofuels or biochemicals hinges on more efficient bioconversion processes. While microbial conversion can offer robust solutions, the native microbial growth process often redirects a large fraction of carbon to CO 2 and cell mass. By integrating genome-scale metabolic models with techno-economic and life cycle assessment models, this study analyzes the effects of converting cell mass lipids to hydrocarbon fuels, and CO 2 to methanol on the facility’s costs and life-cycle carbon footprint. Results show that upgrading microbial lipids or both microbial lipids and CO 2 using renewable hydrogen produces carbon-negative bisabolene. Additionally, on-site electrolytic hydrogen production offers a supply of pure oxygen to use in place of air for bioconversion and fuel combustion in the boiler. To reach cost parity with conventional jet fuel, renewable hydrogen needs to be produced at less than $\$2.2$ to $\$3.1$/kg, with a bisabolene yield of 80% of the theoretical yield, along with cell mass and CO 2 yields of 22 wt% and 54 wt%, respectively. The economic combination of cell mass, CO 2 , and bisabolene yields demonstrated in this study provides practical insights for prioritizing research, selecting suitable hosts, and determining necessary engineered production levels.

09 BIOMASS FUELS↗