Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Propellant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80
All sourcesNASA NTRSDOE OSTI
NASA NTRS1950

Altitude Investigation of Performance of Turbine-propeller Engine and Its Components

An investigation was conducted on a turbine-propeller engine in the NACA Lewis altitude wind tunnel at altitudes from 5000 to 35,000 feet. The applicability of generalized parameters to turbine-propeller engine data, analyses of the compressor, the combustion chambers, and the turbine, and a study of the over-all engine performance are reported. Engine performance data obtained at sea-level static conditions could be used to predict static performance at altitudes up to 35,000 feet by use of the standard generalized parameters.

Wallner, Lewis E↗
NASA NTRS1957

Rocket thrust variation with foamed liquid propellants

An analysis is presented on a method for varying rocket thrust by varying the bulk density of the propellants. This density variation was accomplished by uniformly dispersing an inert, insoluble gas in the liquid propellants. Only qualitative agreement with theory was obtained from preliminary experiments with a 1000-pound-thrust ammonia - nitric acid rocket engine; the required experimental gas-flow rates were two to six times greater than those predicted by theory. It was demonstrated, however, that this method of rocket-thrust variation is feasible.

Morrell, G↗
NASA NTRS1918

Experimental research on air propellers

The purposes of the experimental investigation on the performance of air propellers described in this report are as follows: (1) the development of a series of design factors and coefficients drawn from model forms distributed with some regularity over the field of air-propeller design and intended to furnish a basis of check with similar work done in other aerodynamic laboratories, and as a point of departure for the further study of special or individual types and forms; (2) the establishment of a series of experimental values derived from models and intended for later use as a basis for comparison with similar results drawn from certain selected full-sized forms and tested in free flight.

Durand, William F↗
NASA NTRS1919

The Design of Wind Tunnels and Wind Tunnel Propellers

Report discusses the theory of energy losses in wind tunnels, the application of the Drzewiecki theory of propeller design to wind tunnel propellers, and the efficiency and steadiness of flow in model tunnels of various types.

Warner, Edward P↗
NASA NTRS1921

Experimental research on air propellers IV

This report states the results of investigations made upon numerous propeller models at the request of the Subcommittee on Aerodynamics, and contains valuable data for those interested in the design of air propellers.

Durand, W F↗
NASA NTRS1923

Tests on air propellers in yaw

This report contains the results of tests to determine the thrust (pull) and torque characteristics of air propellers in movement relative to the air in a line oblique to the line of the shaft, and specifically when such angle of obliquity is large, as in the case of helicopter flight with the propeller serving for both sustentation and traction.

Durand, W F↗
NASA NTRS1924

The general efficiency curve for air propellers

This report presents a formula which may be used to obtain a "general efficiency curve" in addition to the well-known maximum efficiency curve. These two curves, when modified somewhat by experimental data, enable performance calculations to be made without detailed knowledge of the propeller. The curves may also be used to estimate the improvement in efficiency due to reduction gearing, or to judge the performance of a new propeller design.

Diehl, Walter S↗
NASA NTRS1926

Comparison of Tests on Air Propellers in Flight with Wind Tunnel Model Tests on Similar Forms

The purpose of this investigation was to determine the performance, characteristics, and coefficients of full-sized air propellers in flight and to compare these results with those derived from wind-tunnel tests on reduced scale models of similar geometrical form. The full-scale equipment comprised five propellers in combination with a VE-7 airplane and Wright E-4 engine. This part of the work was carried out at the Langley Memorial Aeronautical Laboratory, between May 1 and August 24, 1924, and was under the immediate charge of Mr. Lesley. The model or wind-tunnel part of the investigation was carried out at the Aerodynamic Laboratory of Stanford University and was under the immediate charge of Doctor Durand. A comparison of the curves for full-scale results with those derived from the model tests shows that while the efficiencies realized in flight are close to those derived from model tests, both thrust developed and power absorbed in flight are from 6 to 10 per cent greater than would be expected from the results of model tests.

Durand, W F↗
NASA NTRS1928

Characteristics of propeller sections tested in the variable density wind tunnel

Tests were carried out in the variable density wind tunnel of the National Advisory Committee for Aeronautics on six airfoil sections used by the Bureau of Aeronautics as propeller sections. The sections were tested at pressures of 1 and 20 atmospheres corresponding to Reynolds numbers of about 170,000 and 3,500,000. The results obtained, besides providing data for the design of propellers, should be of special interest because of the opportunity afforded for the study of scale effect on a family of airfoil sections having different thickness ratios. (author)

Jacobs, Eastman N↗
NASA NTRS1929

The Twenty-Foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics

This report describes in detail the new propeller research tunnel of the National Advisory Committee for Aeronautics at Langley Field, Va. This tunnel has an open jet air stream 20 feet in diameter in which velocities up to 110 M. P. H. Are obtained. Although the tunnel was built primarily to make possible accurate full-scale tests on aircraft propellers, it may also be used for making aerodynamic tests on full-size fuselages, landing gears, tail surfaces, and other aircraft parts, and on model wings of large size. (author)

Weick, Fred E↗
NASA NTRS1931

Full-Scale Wind-Tunnel Tests with a Series of Propellers of Different Diameters on a Single Fuselage

Aerodynamic tests were made with four geometrically similar metal propellers of different diameters, on a Wright "Whirlwind" J-5 engine in an open cockpit fuselage. The results show little difference in the characteristics of the various propellers, the only one of any importance being an increase of efficiency of the order of 1 per cent for a 5 per cent increase of diameter, within the range of the tests.

Weick, Fred E↗
NASA NTRS1931

Working Charts for the Selection of Aluminum Alloy Propellers of a Standard Form to Operate with Various Aircraft Engines and Bodies

Working charts are given for the convenient selection of aluminum alloy propellers of a standard form, to operate in connection with six different engine-fuselage combinations. The charts have been prepared from full-scale test data obtained in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics. An example is also given showing the use of the charts.

Weick, Fred E↗
NASA NTRS1931

Full-Scale Wind-Tunnel Tests on Several Metal Propellers Having Different Blade Forms

This report gives the full-scale aerodynamic characteristics of five different aluminum alloy propellers having four different blade forms. They were tested on an open cockpit fuselage with a radial air-cooled engine having conventional cowling. The results show that (1) the differences in propulsive efficiency due to the differences in blade form were small; (2) the form with the thinnest airfoil sections had the highest efficiency; (3) it is advantageous as regards propulsive efficiency for a propeller operating in front of a body, such as a radial engine, to have its pitch reduced toward the hub.

Weick, Fred E↗
NASA NTRS1934

Static thrust of airplane propellers

Static thrust data from more than 100 airplane propeller tests are collected from various sources and combined in working charts, from which the static thrust coefficient may be readily determined. The available data cover practically all types of propellers and are in good agreement.

Diehl, Walter S↗
NASA NTRS1937

Characteristics of Six Propellers Including the High-Speed Range

This investigation is part of an extensive experimental study that has been carried out at full scale in the NACA 20-foot tunnel, the purpose of which has been to furnish information in regard to the functioning of the propeller-cowling-nacelle unit under all conditions of take-off, climbing, and normal flight. This report presents the results of tests of six propellers in the normal and high-speed flight range and also includes a study of the take-off characteristics.

Theodorsen, Theodore↗
NASA NTRS1938

The Effect of Compressibility on Eight Full-Scale Propellers Operating in the Take-Off and Climbing Range

Tests were made of eight full-scale propellers of different shape at various tip speeds up to about 1,000 feet per second. The range of blade-angle settings investigated was from 10 degrees to 30 degrees at the 0.75 radius. The results indicate that a loss in propulsive efficiency occurred at tip speeds from 0.5 to 0.7 the velocity of sound for the take-off and climbing conditions. As the tip speed increased beyond these critical values, the loss rapidly increased and amounted, in some instances, to more than 20 percent of the thrust power for tip-speed values of 0.8 the speed of sound. In general, as the blade-angle setting was increased, the loss started to occur at lower tip speeds. The maximum loss for a given tip speed occurred at a blade-angle setting of about 20 degrees for the take-off and 25 degrees for the climbing condition. A simplified method for correcting propellers for the effect of compressibility is given in an appendix.

Biermann, David↗
NASA NTRS1938

The Torsional and Bending Deflection of Full-Scale Aluminum-Alloy Propeller Blades Under Normal Operating Conditions

The torsional deflection of the blades of three full-scale aluminum-alloy propellers operating under various loading conditions was measured by a light-beam method. Angular bending deflections were also obtained as an incidental part of the study. The deflection measurements showed that the usual present-day type of propeller blades twisted but a negligible amount under ordinary flight conditions. A maximum deflection of about 1/10 degree was found at a v/nd of 0.3 and a smaller deflection at higher values of v/nd for the station at 0.70 radius. These deflections are much smaller than would be expected from earlier tests, but the light-beam method is considered to be much more accurate than the direct-reading-transit method used in the previous test.

Hartman, Edwin P↗
NASA NTRS1940

Static Thrust and Power Characteristics of Six Full-Scale Propellers

Static thrust and power measurements were made of six full-scale propellers. The propellers were mounted in front of a liquid-cooled-engine nacelle and were tested at 15 different blade angles in the range from -7 1/2 degrees to 35 degrees at 0.75r. The test rig was located outdoors and the tests were made under conditions of approximately zero wind velocity.

Hartman, Erwin P↗