Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

The Effects of Crossflow on the Pressures and Lift Induced by the Fountain Generated Between Two Impinging Jets

When a jet STOVL aircraft is hovering, or in a crossflow, while close to the ground wall jets flowing radially outward from the impingement points of the jets are generated. An upflow, or fountain, is generated where the wall jets from adjacent jets meet on the ground surface. The induced lift and suckdown generated by the impingement of the fountain on the lower surface of the configuration has been the subject of previous studies. This study analyzes the limited available pressure and force data on the effect of crossflow on the fountain induced lift and suckdown. The analysis includes the effects of jet spacing, height and operating conditions. However, it is limited to twin jet configurations of circular, vertical jets operating at subcritical nozzle pressure ratios over a fixed ground surface.

Kuhn, Richard E.↗

Review on the effects of hydrogen at extreme pressures and temperatures on the mechanical behavior of polymers.

The effects of hydrogen on the mechanics (e.g. strength, ductility, and fatigue resistance) of polymer materials are outlined in this report. There are a small number of studies reported in the literature on this topic, and even fewer at the extreme temperatures to which hydrogen service materials will be exposed. Several studies found little evidence that hydrogen affects the static tensile properties, long term creep, or ductile fracture of high density polyethylene or polyamide. However, there has been a report that a recoverable drop in the modulus of high density polyethylene is observable under high hydrogen pressure. A research need exists on the mechanical effects of hydrogen on the wide range of polymers used or considered for use in the hydrogen economy, due to the lack of data in the literature.

Hecht, Ethan S.↗

Interaction between a vortex and a turbulent boundary layer in a streamwise pressure gradient

The effect of a moderate adverse pressure gradient on the interaction between a single streamwise vortex and a turbulent boundary layer is investigated experimentally. Quantitative characterization of vortex properties based on measurements of the mean cross-flow velocity components is attained. Growth of the vortex core is observed, followed by a flattening of the core shape which occurs when the core radius becomes comparable to the distance of the vortex center from the surface. The adverse pressure gradient causes an increase in the rate of core growth and, therefore, a stronger distortion of the core shape. Turbulence properties are even more strongly disturbed by an adverse pressure gradient than by constant pressure.

Westphal, R. V.↗

Experimental Study of a Three-Dimensional Shear-Driven Turbulent Boundary Layer with Streamwise Adverse Pressure Gradient

The effects of a strong adverse pressure gradient on a three-dimensional turbulent boundary layer are studied in an axisymmetric spinning cylinder geometry. Velocity measurements made with a three-component laser Doppler velocimeter include all three mean flow components, all six Reynolds stress components, and all ten triple-product correlations. Reynolds stress diminishes as the flow becomes three-dimensional. Lower levels of shear stress were seen to persist under adverse pressure gradient conditions. This low level of stress was seen to roughly correlate with the magnitude of cross-flow (relative to free stream flow) for this experiment as well as most of the other experiments in the literature. Variations in pressure gradient do not appear to alter this correlation. For this reason, it is hypothesized that a three-dimensional boundary layer is more prone to separate than a two-dimensional boundary layer, although it could not be directly shown here. None of the computations performed with either a Prandtl mixing length, k-epsilon, or a Launder-Reece-Rodi full Reynolds-stress model were able to predict the reduction in Reynolds stress.

Driver, David M.↗

Boundary Layer Effect on the Surface Pressure of an Infinite Cone in Supersonic Flow

The theory of Taylor and Maccoll (Ref,1) gives the surface pressure on an infinite cone in supersonic flow as a function of the cone vertex angle and the free stream Mach number and static pressure for a gas of vanishing viscosity. When a slender conical probe is used together with an impact pressure probe to determine the static pressure and Mach number in a low density gas stream, it is desirable to have some theoretical estimate of the effect of viscous boundary layer on the probe readings. Theoretical and experimental results with respect to impact probes have been presented in Refs. 5 and 6. A simple approximation for a conical probe based on linearized supersonic flow and compressible boundary layer theory is presented here.

Lin, T. C.↗

Spin-strain interactions under hydrostatic pressure in α-RuCl 3

We investigate the effects of hydrostatic pressure on 𝛼−RuCl 3 , a prototypical material for the Kitaev spin model on a honeycomb lattice with a possible spin-liquid ground state. Using ultrasound measurements at pressures up to 1.16 GPa, we reveal significant modifications of the acoustic properties and the 𝐻−𝑇 phase diagram of this material. Hydrostatic pressure suppresses the three-dimensional magnetic order and induces a dimerization transition at higher pressures. At low pressures, the sound attenuation exhibits a linear temperature dependence, while above 0.28 GPa, it becomes nearly temperature independent, suggesting a shift in the phonon scattering regime dominated by Majorana fermions. These findings provide new insights into spin-strain interactions in Kitaev magnets and deliver a detailed characterization of the 𝐻−𝑇 phase diagram of 𝛼−RuCl 3 under hydrostatic pressure.

Focused ion beam↗

A study of real jet effects on the surface pressure distribution induced by a jet in a crossflow

A study of jet exit profile, exit Mach number, swirl and turbulence level on jet-induced loadings for jets exhausting from a surface into a crossflow is presented. The importance of each of these real jet characteristics is assessed using available data. Where adequate surface pressure distribution data are available, a correlation method to predict surface pressure for a jet exhausting from an infinite flat plate is used either to attempt to develop a correlation based on the real jet characteristics or to model the effects of that characteristic. Data comparisons are presented for selected cases. Also, a summary of information on surface pressure distribution data for jet exhausting from flat plates into a subsonic crossflow is presented.

Perkins, S. C., Jr.↗

Investigation on the effect of nonlinear processes on similarity law in high-pressure argon discharges

In this paper, the effect of nonlinear processes (such as three-body collisions and stepwise ionizations) on the similarity law in high-pressure argon discharges has been studied by the use of the Kinetic Global Model framework. In the discharge model, the ground state argon atoms (Ar), electrons (e), atom ions (Ar + ), molecular ions (Ar 2 + ), and fourteen argon excited levels Ar*(4s and 4p) are considered. The steady-state electron and ion densities are obtained with nonlinear processes included and excluded in the designed models, respectively. It is found that in similar gas gaps, keeping the product of gas pressure and linear dimension unchanged, with the nonlinear processes included, the normalized density relations deviate from the similarity relations gradually as the scale-up factor decreases. Without the nonlinear processes, the parameter relations are in good agreement with the similarity law predictions. Furthermore, the pressure and the dimension effects are also investigated separately with and without the nonlinear processes. It is shown that the gas pressure effect on the results is less obvious than the dimension effect. Without the nonlinear processes, the pressure and the dimension effects could be estimated from one to the other based on the similarity relations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of spatial inlet temperature and pressure distortion on turbofan engine stability

The effects of circumferential and radial inlet temperature distortion, circumferential pressure distortion, and combined temperature and pressure distortion on the stability of an advanced turbofan engine were investigated experimentally at simulated altitude conditions. With circumferential and radial inlet temperature distortion, a flow instability generated by the fan operating near stall caused the high-pressure compressor to surge at, or near, the same time as the fan. The effect of combined distortion was dependent on the relative location of the high-temperature and low-pressure regions; high-pressure compressor stalls occurred when the regions coincided, and fan stalls occurred with the regions separated.

Mehalic, Charles M.↗

Effect of spatial inlet temperature and pressure distortion on turbofan engine stability

The effects of circumferential and radial inlet temperature distortion, circumferential pressure distortion, and combined temperature and pressure distortion on the stability of an advanced turbofan engine were investigated experimentally at simulated altitude conditions. With circumferential and radial inlet temperature distortion, a flow instability generated by the fan operating near stall caused the high-pressure compressor to surge at, or near, the same time as the fan. The effect of combined distortion was dependent on the relative location of the high-temperature and low-pressure regions; high-pressure compressor stalls occurred when the regions coincided, and fan stalls occurred with the regions separated.

Mehalic, Charles M.↗

Molecular Dynamics Study of CO 2 and H 2 O Intercalation in Smectite Clays: Effect of Temperature and Pressure on Interlayer Structure and Dynamics in Hectorite

Grand Canonical Molecular Dynamics (GCMD) simulations were performed to investigate the intercalation of CO 2 and H 2 O molecules in the interlayers of the smectite clay, Na-hectorite, at temperatures and pressures relevant to petroleum reservoir and geological carbon sequestration conditions and in equilibrium with H 2 O-saturated CO 2 . The computed adsorption isotherms indicate that CO 2 molecules enter the interlayer space of Na-hectorite only when it is hydrated with approximately three H 2 O molecules per unit cell. The computed immersion energies show that the bilayer hydrate structure (2WL) contains less CO 2 than the monolayer structure (1WL) but that the 2WL hydrate is the most thermodynamically stable state, consistent with experimental results for a similar Na-montmorillonite smectite. Under all T and P conditions examined (323–368 K and 90–150 bar), the CO 2 molecules are adsorbed at the midplane of clay interlayers for the 1WL structure and closer to one of the basal surfaces for the 2WL structure. Interlayer CO 2 molecules are dynamically less restricted in the 2WL structures. The CO 2 molecules are preferentially located near basal surface oxygen atoms and H 2 O molecules rather than in coordination with Na+ ions. Accounting for the orientation and flexibility of the structural -OH groups of the clay layer has a significant effect on the details of the computed structure and dynamics of H 2 O and CO 2 molecules but does not affect the overall trends with changing basal spacing or the principal structural and dynamical conclusions. Temperature and pressure in the ranges examined have little effect on the principal structural and energetic conclusions, but the rates of dynamical processes increase with increasing temperature, as expected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of steady-state pressure distortion on the stall margin of a J85-21 turbojet engine

The effects of the inlet pressure distortions, induced by five screen patterns, on the performance of a J85-21 turbojet engine was conducted at the NASA Lewis Research Center. Testing was in support of the HiMAT RPRV program at Dryden Flight Research Center. Distortion patterns were chosen based on anticipated application of test results of the HiMAT installation. Tests were conducted at a simulated Mach number and altitude condition of 0.9 and 10 973 meters. Results are presented in terms of distortion levels and standard compressor performance parameters.

Bobula, G. A.↗

Synergistic effect of alloying elements doping and external pressure on the elastic property of Ni{sub 3}Al: A first-principles study

In this paper, the basic electronic structures and elastic properties of Ni{sub 3}Al doping with alloying elements (Re, Cr, and Mo) under different pressures have been investigated using first-principles calculations based on density functional theory. It is shown that both alloying elements and external applied pressure contribute positively to the elastic properties of Ni{sub 3}Al, and the configurations of the compounds remain almost unchanged. The calculated elastic constants and moduli increase linearly with the pressure increasing from 0 and 40 GPa. Among the alloying elements studied in the present work, Re exhibits the most significant effect compared with the other elements, showing its practical importance. Especially, if both alloying elements doping and pressure effects are considered simultaneously, which has not been considered previously, the studied compounds exhibit an even better elastic property than the simple superposition of the two influences. Such synergistic effect demonstrates promising applications of Ni-based single crystal superalloys in possible extreme mechanical environments.

36 MATERIALS SCIENCE↗

Nuclear quantum effects on the high pressure melting of dense lithium

Using a self-developed combination of the thermodynamic integration and the ab initio path-integral molecular dynamics methods, we quantitatively studied the influence of nuclear quantum effects (NQEs) on the melting of dense lithium at 45 GPa. We find that although the NQEs significantly change the free-energies of the competing solid and liquid phases, the melting temperature (T{sub m}) is lowered by only ∼15 K, with values obtained using both classical and quantum nuclei in close proximity to a new experiment. Besides this, a substantial narrowing of the solid/liquid free-energy differences close to T{sub m} was observed, in alignment with a tendency that glassy states might form upon rapid cooling. This tendency was demonstrated by the dynamics of crystallization in the two-phase simulations, which helps to reconcile an important conflict between two recent experiments. This study presents a simple picture for the phase diagram of lithium under pressure. It also indicates that claims on the influence of NQEs on phase diagrams should be carefully made and the method adopted offers a robust solution for such quantitative analyses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Effect of Inlet Temperature and Pressure on the Efficiency of a Single-stage Impulse Turbine Having a 13.2-inch Pitch-line Diameter Wheel

Efficiency tests have been conducted on a single-stage impulse turbine having a 13.2-inch pitch-line diameter wheel and a cast nozzle diaphram over a range of turbine speeds from 3000 to 17,000 rpm, pressure ratios from 1.5 to 5.0, inlet total temperatures from 1200 deg to 2000 deg R, and inlet total pressures from 18 to 59 inches of mercury absolute. The effect of inlet temperature and pressure on turbine efficiency for constant pressure ration and blade-to-jet speed ration is correlated against a factor derived from the equation for Reynolds number. The degree of correlation indicates that the change in turbine efficiency with inlet temperature and [ressure for constant pressure ration and blade-to-jet speed ration is principally a Reynolds number effect.

TURBINES - WHEELS↗

The influence of warm-season precipitation on the diel cycle of the surface energy balance and carbon dioxide at a Colorado subalpine forest site

Precipitation changes the physical and biological characteristics of an ecosystem. Using a precipitation-based conditional sampling technique and a 14 year data set from a 25 m micrometeorological tower in a high-elevation subalpine forest, we examined how warm-season precipitation affected the above-canopy diel cycle of wind and turbulence, net radiation R net , ecosystem eddy covariance fluxes (sensible heat H , latent heat LE, and CO 2 net ecosystem exchange NEE) and vertical profiles of scalars (air temperature T a , specific humidity q , and CO 2 dry mole fraction χ c ). This analysis allowed us to examine how precipitation modified these variables from hourly (i.e., the diel cycle) to multi-day time-scales (i.e., typical of a weather-system frontal passage). During mid-day we found the following: (i) even though precipitation caused mean changes on the order of 50–70 % to R net , H , and LE, the surface energy balance (SEB) was relatively insensitive to precipitation with mid-day closure values ranging between 90 and 110 %, and (ii) compared to a typical dry day, a day following a rainy day was characterized by increased ecosystem uptake of CO 2 (NEE increased by ≈ 10 %), enhanced evaporative cooling (mid-day LE increased by ≈ 30 W m −2 ), and a smaller amount of sensible heat transfer (mid-day H decreased by ≈ 70 W m −2 ). Based on the mean diel cycle, the evaporative contribution to total evapotranspiration was, on average, around 6 % in dry conditions and between 15 and 25 % in partially wet conditions. Furthermore, increased LE lasted at least 18 h following a rain event. At night, even though precipitation (and accompanying clouds) reduced the magnitude of R net , LE increased from ≈ 10 to over 20 W m −2 due to increased evaporation. Any effect of precipitation on the nocturnal SEB closure and NEE was overshadowed by atmospheric phenomena such as horizontal advection and decoupling that create measurement difficulties. Above-canopy mean χ c during wet conditions was found to be about 2–3 μmol mol −1 larger than χ c on dry days. This difference was fairly constant over the full diel cycle suggesting that it was due to synoptic weather patterns (different air masses and/or effects of barometric pressure). Finally, the effect of clouds on the timing and magnitude of daytime ecosystem fluxes is described.

54 ENVIRONMENTAL SCIENCES↗

Activity coefficients of siderophile elements in Fe-Si liquids at high pressure

Metallic core formation in differentiated bodies in the inner solar system can take place between low pressures (near 1 bar) to much higher pressures (up to 100 GPa). Most thermodynamic models of metal-silicate equilibria utilise activity coefficients for metallic tracers in Fe liquids, nearly all of which have been carried out at low pressures. This study focuses on the effect of pressure on activity coefficients for Au, P, V, Mn, Ga, Zn, Cd, Sn, W, Pb, and Nb in liquid Fe-Si alloys. From a series of experiments at 10 GPa, 2373 K containing variable Si content in a metallic liquid we have derived epsilon interaction parameters in Fe-Si liquids ($ε^{Si}_{M}$). Comparison of 1 GPa and 10 GPa data shows no difference except for Nb. Epsilon parameters derived from low pressure experiments can thus be used to calculate activity coefficients for application to higher pressure processes (at least to 10 GPa).

58 GEOSCIENCES↗