Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA ELECTRODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Contribution of positive and negative ions to the electrohydrodynamic force in a dielectric barrier discharge plasma actuator operating in air

We present a parametric study of the electrohydrodynamic force generated by surface dielectric barrier discharge plasma actuators in air for sinusoidal voltage waveforms. The simulation results confirm that momentum is transferred from the charged particles to the neutral species in the same direction during both positive and negative parts of the cycle. The momentum transfer is due to positive ions during the positive part of the cycle (electrode above the dielectric layer is the anode), and to negative ions during the negative part of the cycle. The relative contribution of the positive and negative parts of the cycle depends on the voltage amplitude and frequency. The model predicts that the contribution of negative ions tends to be dominant at low voltage frequencies and high voltage amplitudes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optical emission characteristics of surface nanosecond pulsed dielectric barrier discharge plasma

This paper reports an experimental study of the optical emission characteristics of the surface dielectric barrier discharge plasma excited by nanosecond pulsed voltage. N{sub 2}(C{sup 3}{Pi}{sub u}) rotational and vibrational temperatures are almost the same with upper electrode powered with positive polarity and lower electrode grounded or upper electrode grounded and lower electrode powered with positive polarity. While the electron temperature is 12% higher with upper electrode powered with positive polarity and lower electrode grounded. When the frequency is below 2000 Hz, there is almost no influence of applied voltage amplitude and frequency on N{sub 2}(C{sup 3}{Pi}{sub u}) rotational, vibrational temperature and electron temperature. As the pressure decreases from 760 Torr to 5 Torr, N{sub 2}(C{sup 3}{Pi}{sub u}) rotational temperature remains almost unchanged, while its vibrational temperature decreases initially and then increases. The discharge mode changes from a filamentary type to a glow type around 80 Torr. In the filamentary mode, the electron temperature remains almost unchanged. In the glow mode, the electron temperature increases while the pressure decreases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimization of nanosecond transient plasma ignition for clean combustion

Based on a previously developed, retrofittable nanosecond pulsed TPS ignition prototype, transient plasma ignition technology is evaluated for higher energy efficiency and lower emission by optimizing pulse power conditions using advanced diagnostic-based approaches. Combustion performances of a TPS ignition electrode powered by nanosecond voltage pulses of two different rising times (i.e. 4 ns and 8 ns) but the same full-width-half-maximum (FWHM) of 6 ns were compared for single-shot and high-repetition-rate ignitions. The use of faster risetime reduces the voltage amplitude criterion for combustion ignition under a single-shot, stoichiometric fuel-air condition, resulting in higher energy efficiency. In addition, it was demonstrated that high-frequency bursts of pulses positively affect the combustion process; four-consecutive pulsed plasma ignition at a pulse repletion rate (PRR) of 1 kHz needs only half of the voltage to achieve combustion, and increasing the PRR from 1 kHz to 10 kHz improves the energy efficiency by a factor of >1.3. A prototype of retrofittable nanosecond pulsed ignition system was developed and tested in a newly built testing/diagnostic platform, paving the way for ultimate optimization of the TPS prototype for low cost, highly efficient, and low emission combustion.

02 PETROLEUM↗

Swinging reciprocating Mach probes for the high field side scrape-off layer in DIII-D

A new pair of in situ reciprocating Mach probes termed swing probes has been deployed on the DIII-D centerpost for the 2012 experimental campaign. When not deployed, the entire assembly is housed in a <5 cm space underneath the centerpost tiles. This design is unique in that the probe swings vertically through the edge plasma, taking measurements along a 180 Degree-Sign arc with a 20 cm radius. The motion is powered by actuator coils that interact with the tokamak's magnetic field. Two electrodes maintain a Mach-pair orientation throughout the swing and provide measurements of saturation current, electron temperature, and parallel flow speeds up to the separatrix.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Plasma Ignition and Combustion Stabilization Technology to Improve Flexible Operation, Reliability and Economics of an Existing Coal-Fired Boiler

GE Steam Power, Inc. (GE) proposed to improve reliability, flexibility, and economics of an existing coal-fired power plant by applying a new advanced technology developed by GE, a plasma-assisted pulverized fuel firing system. The objective of this program is to demonstrate the achievement of lower load by improved flame stabilization and therefore lower operating costs in a full-scale field installation at coal-fired electric utility. GE’s Plasma Ignition and Combustion Stabilization System is designed to operate continuously to support low load operation. With the plasma on, the flame will be attached and stable, removing the firing system as a limitation to low load operation. In addition, GE’s exclusively from ABENZ company licensed AC based technology has a 90+% system efficiency compared to all other systems at which are DC and operate with ~75% efficiency. Plant operating costs are lowered by eliminating use of expensive support fuel as well as the ability to operate at lower loads. The utilities’ ability to better match the demand curve will result in significant savings. Maintenance is lower for an AC system than a DC system as it operates at lower current. This eliminates the need for a demineralized cooling water system and provides longer electrode life which translates into both material and labor savings. It is the objective of GE to not only demonstrate the additional low load achievable with a plasma system after best achievable tuning, sensor and software approach has been exhausted, but also the increased stability of the flame at all loads with plasma assistance as well as cost savings at all low loads using plasma instead of oil. Upon successful completion of this project, GE will have sufficient field experience to rapidly deploy the Plasma Technology. The project objectives were achieved through the implementation of plasma ignitor technology at PacifiCorp Hunter Station Unit 3. A plasma ignitor system was retrofitted on ten wall-fired burners, Mill 3-4 combustion system. The Plasma Ignitors installed at Hunter proved that this GE technology is a direct and complete replacement for the original oil ignitors. The Hunter Unit 3 burner management system allows the plasma system to be used in all applications that originally required oil to be burned. This includes any time the Mill 3-4 is started or stopped for any reason including boiler starts, load changes, and low load support.

01 COAL, LIGNITE, AND PEAT↗

Magnetic Electrochemical Immunoassays with Quantum Dot Labels for Detection of Phosphorylated Acetylcholinesterase in Plasma

A new magnetic electrochemical immunoassay has been developed as a tool for biomonitoring exposures to organophosphate (OP) compounds, e.g., insecticides and chemical nerve agents, by directly detecting organophosphorylated acetylcholinesterase (OP-AChE). This immunoassay uniquely incorporates highly efficient magnetic separation with ultrasensitive square wave voltammetry (SWV) analysis with quantum dots (QDs) as labels. A pair of antibodies was used to achieve the specific recognition of OP-AChE that was prepared with paraoxon as an OP model agent. Antiphosphoserine polyclonal antibodies were anchored on amorphous magnetic particles preferably chosen to capture OP-AChE from the sample matrixes by binding their phosphoserine moieties that were exposed through unfolding the protein adducts. This was validated by electrochemical examinations and enzyme-linked immunosorbent assays. Furthermore, antihuman AChE monoclonal antibodies were labeled with cadmium-source QDs to selectively recognize the captured OP-AChE, as characterized by transmission electron microscopy. The subsequent electrochemical SWV analysis of the cadmium component released by acid from the coupled QDs was conducted on disposable screen-printed electrodes. Experimental results indicated that the SWV-based immunoassays could yield a linear response over a broad concentration range of 0.3-300 ng/mL OP-AChE in human plasma with a detection limit of 0.15 ng/mL. Such a novel electrochemical immunoassay holds great promise as a simple, selective, sensitive, and field-deployable tool for the effective biomonitoring and diagnosis of potential exposures to nerve agents and pesticides.

59 BASIC BIOLOGICAL SCIENCES↗

Characteristics of nanosecond pulse needle-to-plane discharges at high pressure: a particle-in-cell Monte Carlo collision simulation

A model of one dimensional in position and three dimensional in velocity space self-consistent particle in cell with Monte Carlo collision technique was employed to simulate the argon discharge between the needle and plane electrodes at high pressure, in which a nanosecond rectangular pulse was applied to the needle electrode. The work focused on the investigation of the spatiotemporal evolution of the discharge versus the needle tip size and working gas pressure. The simulation results showed that the discharge occurred mainly in the region near the needle tip at atmospheric pressure, and that the small radius of the needle tip led to easy discharge. Reducing the gas pressure gave rise to a transition from a corona discharge to a glowlike discharge along the needle-to-plane direction. The microscopic mechanism for the transition can arguably be attributed to the peak of high-energy electrons occurring before the breakdown; the magnitude of the number of these electrons determined whether the breakdown can take place.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Atomic and molecular effects on spherically convergent ion flow. II. Multiple molecular species

A theoretical model for the effect of molecular interactions on the flow of molecular ions in spherically convergent geometry where the inner grid (cathode) is at a large negative potential and the outer grid (anode) is grounded has been developed. The model assumes a weakly ionized deuterium plasma composed of D{sup +}, D{sub 2}{sup +}, and D{sub 3}{sup +} ions that interact with the dominant background gas (D{sub 2}). The interactions included are charge exchange, ionization, and dissociative processes. The formalism developed includes the bouncing motion of the ions in the electrostatic well and sums over all generations of subsequent ions produced by atomic and molecular processes. This leads to a set of two coupled Volterra integral equations, which are solved numerically. From the solution of the Volterra equations, one can obtain quantities of interest, such as the energy spectra of the ions and fast neutral atoms and molecules, and the fusion reaction rate. To provide an experimental test, the model is applied to inertial electrostatic devices and the calculated neutron production rate is compared to previously reported measurements for one University of Wisconsin inertial electrostatic confinement device [D. C. Donovan et al., Fusion Sci. Technol. 56, 507 (2009)]. The results show general agreement with the experimental results, but significant differences remain to be resolved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

In situ studies of a molten metal anode ablation in a nearly atmospheric pressure DC arc

A DC arc with a meltable metal anode in a near-atmospheric pressure hydrocarbon gas is an emerging method for producing single-walled carbon nanotubes (SWCNTs). In these systems, evaporation of the molten metal anode determines the formation of catalyst seed particles needed for SWCNT growth, and therefore, should be monitored, controlled, and optimized. Evaluating the anode ablation rate by weighing the anode before and after a synthesis run is unfeasible due to anode carburization in the hydrocarbon atmosphere. To overcome this, we implemented a high-speed, 2D, 2-color pyrometry for reliable temperature measurements of the molten anode in a DC arc. The obtained temperature fields were used to calculate the anode ablation rates. Results showed the importance of resolving the arc and molten pool dynamics, as well as addressing the issue of reflections. Furthermore, significant changes in ablation rates were revealed upon addition of CH 4 , which must be considered when scaling up the production of SWCNTs.

Marangoni↗

Study of the prebreakdown stage of a gas discharge in a diode with point cathode by laser probing

The prebreakdown stage of a gas discharge in a diode with strongly overloaded cathode is studied by laser methods (by simultaneous use of multiframe interferometry and shadow and schlieren photographing) at atmospheric pressure. The spatial resolution of the methods is about 20 μm. A probing pulse of a laser (LS-2151 Nd: YAG laser with a half amplitude duration of 70 ps and a pulse energy of up to 40 mJ) is synchronized with a voltage pulse with accuracy of about 1 ns. High field strength at the cathode is achieved due to the use of thin individual metal tips on the electrodes. It is shown that the initial stage of breakdown of a discharge gap is accompanied by the emergence of a dense plasma cloud at the end of a tip with electron density of about 5 × 10{sup 19} cm{sup –3} with a size of tens of microns, as well as by a sharp increase in the total current through the diode. After the emergence of a dense plasma cloud at the end of a cathode tip, a similar cloud is formed on the surface of the anode; sometime later, these clouds join together and form a tubular current channel. The dynamics of the breakdown, as well as the parameters of the plasma are studied by the abovementioned techniques in three independent optical channels.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pulsed electromagnetic gas accelleration

Direct measurement with thermocouples of the power deposited in the anode of a multi-megawatt magnetoplasmadynamic discharge has shown the fractional anode power to decrease from 50% at 200 kW to 10% at 20 MW. Using local measurements of current density, electric potential, and electron temperature, the traditional model for heat conduction to the anode is found to be inadequate. Other experiments in which the voltage-current characteristics and exhaust velocities of MPD arcs using Plexiglas and boron nitride chamber insulators and various mass injection configurations show that ablation can affect nominal accelerator operation in several distinct ways. The incorporation of a hollow cathode in a 7 kA plasma discharge has shown that a stable current attachment can be realized in the cavity without the aid of cathode heaters, keeper electrodes, or emissive coatings.

Jahn, R. G.↗

Impedance characteristics of coaxial and planar magnetoplasma capacitors

A theory has been developed for the impedance of a homogeneous magnetoplasma enclosed between two specular reflecting coaxial electrodes, with a static magnetic field parallel to the electrode axes. The parallel-plate magnetoplasma capacitor is treated as a sub-case. Starting with the Vlasov equation, an integral equation is derived for the electric field. Solving this equation, and integrating to obtain the voltage, gives the capacitor impedance. This includes a capacitive component, and a resistive component expressing the Landau damping associated with the open orbits of electrons reflected at the electrodes. A direct numerical solution of the field integral equation has been carried out for a range of values of magnetic field, plasma density, and signal frequency. The values of impedance so obtained are compared with the predictions of macroscopic theory, and of an approximate microscopic theory in which open orbits are ignored and solutions are obtained using finite Fourier transform methods. The mathematical relations between these theories are demonstrated.

Harker, K. J.↗

Coulomb expansion of a thin dust cloud observed experimentally under afterglow plasma conditions

The Coulomb expansion of a thin cloud of charged dust particles was observed experimentally, in a plasma afterglow. This expansion occurs due to mutual repulsion among positively charged dust particles, after electrons and ions have escaped the chamber volume. In the experiment, a two-dimensional cloud of dust particles was initially levitated in a glow-discharge plasma. The power was then switched off to produce afterglow conditions. The subsequent fall of the dust cloud was slowed by reversing the electric force, to an upward direction, allowing an extended observation. At early time, measurements of the Coulomb expansion in the horizontal direction are found to be accurately modeled by the equation of state for a uniformly charged thin disk. Finally, bouncing from the lower electrode was found to be avoided by lowering the impact velocity <100 mm/s.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stability and size of particle pairs in complex plasmas

Particle pairing in a complex plasma was experimentally studied with the emphasis on pair spatial extent and stability. Micron-size particles were suspended in the (pre)sheath area above the lower electrode in a capacitively coupled radio-frequency discharge in argon. They formed vertical pairs due to the ion wakes created by the flow of ions past particles. We discuss the confinement mechanism for the lower particle, resulting from a combination of the wake field and the field of non-uniform sheath. A model of particle pairs is proposed, which provides good description for the dependence of pair size and stability on experimental parameters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Physical Reasoning to Synchronize Electrical Signals and Related Diagnostics in Plasma Focus Devices

Plasma Focus (PF) devices as well as other similar pulsed discharge devices requires a variety of diagnostics for their proper control and optimization, including the voltage between electrodes, the time derivative of the discharge current, detection of X-rays and neutron emissions, and pulsed laser images (Shadow, Schlieren, interferograms). This article discusses the problem of the time reference of all these outputs and proposes specific techniques for synchronizing them based on sound physical grounds. The foundations of synchronization criterion are verified in several experiments on PF devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of annular magnet on discharge characteristics in enhanced glow discharge plasma immersion ion implantation

A permanent annular magnet positioned at the grounded anode alters the discharge characteristics in enhanced glow discharge plasma immersion ion implantation (EGD-PIII). The nonuniform magnetic field increases the electron path length and confines electron motion due to the magnetic mirror effect and electron-neutral collisions thus occur more frequently. The plasma potential and ion density measured by a Langmuir probe corroborate that ionization is improved near the grounded anode. This hybrid magnetic field EGD-PIII method is suitable for implantation of gases with low ionization rates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of flow regimes in arc plasma–gas interactions using a two-temperature arc in crossflow model

The perpendicular impingement of a gas stream on an electric arc, a configuration known as the arc in crossflow, is of primary relevance in the study of plasma-gas interactions, as well as in industrial applications such as circuit breakers and wire-arc spraying. The flow dynamics in the arc in crossflow are the result of coupled fluid-thermal-electromagnetic phenomena accompanied by large property gradients, which can produce significant deviations from Local Thermodynamic Equilibrium (LTE) among electrons and gas species. These characteristics can lead to the establishment of distinct flow regimes depending on the relative values of the controlling parameters of the system, such as inflow velocity, arc current, and inter-electrode spacing. A two-temperature non-LTE (NLTE) model is used to investigate the arc dynamics and the establishment of flow regimes in the arc in crossflow. The plasma flow model is implemented within a nonlinear Variational Multiscale (VMS) numerical discretization approach that is less dissipative, and hence better suited to capture unstable behavior, than traditional VMS methods commonly used in computational fluid dynamics simulations. The Reynolds and the Enthalpy dimensionless numbers, characterizing the relative flow strength and arc strength, respectively, are chosen as the controlling parameters of the system. Simulation results reveal the onset of dynamic behavior and the establishment of steady, periodic, quasi-periodic, and chaotic or potentially turbulent, regimes, as identified by distinct spatiotemporal fluctuations. The computational findings reveal the role of increasing the relative arc strength on enhancing flow stability by delaying the growth of fluctuating and unstable flow behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Process of commutation of a vacuum electric-discharge gap by laser plasma

The temporal parameters of a process of vacuum gap commutation under exposure to a nanosecond pulse of laser radiation incident on the cathode has been studied depending on the radiation energy. Based on the experiment data, it is suggested that a glow discharge is initially ignited in electrode erosion products under exposure to the laser pulse, which due to development of the ionization-overheating instability undergoes the contraction of current channel and transits to an arc discharge. With the radiation energy exceeding a threshold value, the radiation (incident on the cathode) accelerates directly the instability development and the glow discharge transition to the arc discharge due to the radiation absorption in the discharge plasma.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗