SEARCH · Engineering Papers

Results for “Generator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Preliminary test results of electrical charged particle generator for application to fog dispersal

A charged particle generator for use in fog dispersal applications was built and preliminary tests were carried out. The parameter used as a measure of performance was the current measured with a needle probe positioned in the charged jet connected to ground through an ammeter. The needle was movable and allowed the current profile throughout the jet to be determined. The measured current is referred to as the current output. The major independent parameters were liquid water injection rate, plenum pressure, and corona voltage. Optimum current output was achieved at the approximate pressure of 30 psig, corona voltage of 5600 volts, and liquid water injection rate of 6 cc/min. The results of the test with the prototype charged particle generator clearly demonstrate that a current on the order of 20 microamperes can be routinely achieved with the system. This measurement of current does not necessarily represent the total issuing from the nozzle current which is expected to be larger. From these results, confidence was established that a charged particle generator which will operate continuously and consistently can be designed, constructed, and operated. Further work is required, however, to better understand the physical mechanisms involved and to optimize the system for fog dispersal application.

Frost, W.↗

NASA NTRS1980

The MOD-OA 200 kilowatt wind turbine generator design and analysis report

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind turbine generator are discussed. The components, the rotor, driven train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electrical system, and control systems are presented. The rotor includes the blades, hub and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control and Dynamic loads and fatigue are analyzed.

Andersen, T. S.↗

NASA NTRS1982

Utility experience with two demonstration wind turbine generators

Edison has committed 360 MW of nameplate generating capacity to wind energy by year 1990 in its long-range generation plan. To reach this goal the Company's wind energy program focuses on three areas: the continuous evaluation of the wind resource, the hands-on demonstration of wind turbine generators (WTG) and an association with wind park developers. Two demonstration WTGs have been installed and operated at Edison's Wind Energy Center near Palm Springs, California: a 3 MW horizontal axis Bendix/Schachle WTG and a 500 kW vertical axis Alcoa WTG. They are part of a one to two year test program during which the performance of the WTGs will be evaluated, their system operation and environmental impact will be assessed and the design criteria of future WTGs will be identified. Edison's experience with these two WTGs is summarized and the problems encountered with the operation of the two machines are discussed.

Wehrey, M. C.↗

NASA NTRS1983

Pseudo-random number generator for the Sigma 5 computer

A technique is presented for developing a pseudo-random number generator based on the linear congruential form. The two numbers used for the generator are a prime number and a corresponding primitive root, where the prime is the largest prime number that can be accurately represented on a particular computer. The primitive root is selected by applying Marsaglia's lattice test. The technique presented was applied to write a random number program for the Sigma 5 computer. The new program, named S:RANDOM1, is judged to be superior to the older program named S:RANDOM. For applications requiring several independent random number generators, a table is included showing several acceptable primitive roots. The technique and programs described can be applied to any computer having word length different from that of the Sigma 5.

Carroll, S. N.↗

NASA NTRS1983

Electrical power generating system

A power generating system for adjusting coupling an induction motor, as a generator, to an A.C. power line wherein the motor and power line are connected through a triac is described. The triac is regulated to normally turn on at a relatively late point in each half cycle of its operation, whereby at less than operating speed, and thus when the induction motor functions as a motor rather than as a generator, power consumption from the line is substantially reduced.

Nola, F. J.↗

NASA NTRS1983

Solar driven liquid metal MHD power generator

A solar energy collector focuses solar energy onto a solar oven which is attached to a mixer which in turn is attached to the channel of a MHD generator. Gas enters the oven and a liquid metal enters the mixer. The gas/liquid metal mixture is heated by the collected solar energy and moves through the MHD generator thereby generating electrical power. The mixture is then separated and recycled.

Lee, J. H.↗

NASA NTRS1982

Power Generation from Nuclear Reactors in Aerospace Applications

Power generation in nuclear powerplants in space is addressed. In particular, the states of technology of the principal competitive concepts for power generation are assessed. The possible impact of power conditioning on power generation is also discussed. For aircraft nuclear propulsion, the suitability of various technologies is cursorily assessed for flight in the Earth's atmosphere; a program path is suggested to ease the conditions of first use of aircraft nuclear propulsion.

English, Robert E.↗

NASA NTRS1983

Adaptive reference voltage generator for firing angle control of line-commutated inverters

A control system for a permanent-magnet motor driven by a multiphase line-commulated inverter is described. It is provided with integrators for integrating the back EMF of each phase of the motor for use in generating system control signals for an inverter gate logic using a sync and firing angle control generator connected to the outputs of the integrators. The firing angle control signals are produced by the control generator by means for combining 120 deg segments of the integrated back EMF signals symmetrical about their maxima into composite positive and negative waveforms, and means for sampling the maxima of each waveform every 120 deg. These samples are then used as positive and negative firing angle control signals. Whereby any change in amplitude of the integrated back EMF signals will not affect a change in the operating power factor of the motor and inverter.

Dolland, C. R.↗

NASA NTRS1983

Guidelines in preparing computer-generated plots for NASA technical reports with the LaRC graphics output system

To response to a need for improved computer-generated plots that are acceptable to the Langley publication process, the LaRC Graphics Output System has been modified to encompass the publication requirements, and a guideline has been established. This guideline deals only with the publication requirements of computer-generated plots. This report explains the capability that authors of NASA technical reports can use to obtain publication--quality computer-generated plots or the Langley publication process. The rules applied in developing this guideline and examples illustrating the rules are included.

Taylor, N. L.↗

NASA NTRS1982

Generation of desired signals from acoustic drivers

A procedure to control transient signal generation is developed for the study of internal noise propagation from aircraft engines. A simple algorithm incorporating transform techniques is used to produce signals of any desired waveform from acoustic drivers. The accurate driver response is then calculated, and from this the limiting frequency characteristics are determined and the undesirable frequencies where the driver response is poor are eliminated from the analysis. A synthesized signal is then produced by convolving the inverse of the response function with the desired signal. Although the shape of the synthesized signal is in general quite awkward, the driver generates the desired signal when the distorted signal is fed into the driver. The results of operating the driver in two environments, in a free field and in a duct, are presented in order to show the impedance matching effect of the driver. In addition, results using a high frequency cut-off value as a parameter is presented in order to demonstrate the extent of the applicability of the synthesis procedure. It is concluded that the desired signals can be generated through the signal synthesis procedure.

Ramakrishnan, R.↗

NASA NTRS1983

Adaptive grids generated by elliptic systems

It is pointed out that a finite difference grid which moves with the solution of the partial differential equation being solved can improve the accuracy and efficiency of a numerical algorithm. This technique is particularly advantageous in the solution of problems involving boundary layers or shocks where a poorly chosen grid may give a numerical solution which is useless because of poor resolution or extreme oscillations. The present investigation is concerned with the development of a scheme which does not excessively distort the grid. The grid generation algorithm is based on the numerical solution of a system of elliptic differential equations. Holst and Brown (1981) have used a preliminary solution to move points on the boundary of the physical region and then resolved the problem on a new grid generated by an elliptic system. In the current investigation, the grid movement and the solution will develop simultaneously. The solution is used to modify the generating equations, thereby controlling the grid point distributions.

Mastin, C. W.↗

NASA NTRS1983

Noise generation by a finite span swept airfoil

An analysis is developed for the noise generated by a convected gust interacting with a single swept airfoil. The airfoil spans a channel with infinite parallel walls which contains a uniform subsonic mean flow. High frequency gusts, for which the noise generation is concentrated at the airfoil leading edge, are considered. The solution utilizes the Wiener-Hopf technique applied to the equations in nonorthogonal coordinates. Closed form expressions for the farfield acoustic pressure are obtained. The convected gust is assumed to be a plane wave, i.e., the lowest order spanwise mode. Because of the swept leading edge, this convected gust generates acoustic modes of all orders. At high frequencies and low Mach numbers, moderate sweep angles produce substantial noise reductions. The residual acoustic energy is carried mainly by the higher modes. The airfoil sweep also modulates the basic high frequency farfield directivity, producing lobed patterns. The angular modulation of the directivity patterns is most pronounced for the lower order modes.

Kerschen, E. J.↗

NASA NTRS1983

Three-dimensional algebraic grid generation

One of the major approaches to numerical grid generation is the explicit algebraic expression of a physical grid as a function of a uniform grid in a rectangular computational coordinate system. The algebraic methods are based on mathematical interpolation, and the primary advantages are speed and directness. The relation between interpolation and grid generation is described. For three-dimensional grid generation, transfinite interpolation using the coordinate control processes developed in the multisurface method and two-boundary technique are advocated. Grid singularities encountered in three dimensions are discussed, and the exploration of multiple overlapping grids is proposed. Some aspects of interactive algebraic grid computation in three dimensions are discussed.

Smith, R. E.↗

NASA NTRS1983

Portable dynamic pressure generator for static and dynamic calibration of in situ pressure transducers

A portable dynamic pressure generator was developed to meet the requirements of determining the dynamic sensitivities of in situ pressure transducers at low frequencies. The device is designed to operate in a frequency range of 0 to 100 Hz, although it was only tested up to 30 Hz, and to generate dynamic pressures up to 13.8 kPa (2 psi). A description of the operating characteristics and instrumentation used for pressure, frequency, and displacement measurements is given. The pressure generator was used to statically and dynamically calibrate transducers. Test results demonstrated that a difference an exist between the static and dynamic sensitivity of a transducer, confirming the need for dynamic calibrations of in situ pressure transducers.

Bolt, P. A.↗

NASA NTRS1982

XSECT: A computer code for generating fuselage cross sections - user's manual

A computer code, XSECT, has been developed to generate fuselage cross sections from a given area distribution and wing definition. The cross sections are generated to match the wing definition while conforming to the area requirement. An iterative procedure is used to generate each cross section. Fuselage area balancing may be included in this procedure if desired. The code is intended as an aid for engineers who must first design a wing under certain aerodynamic constraints and then design a fuselage for the wing such that the contraints remain satisfied. This report contains the information necessary for accessing and executing the code, which is written in FORTRAN to execute on the Cyber 170 series computers (NOS operating system) and produces graphical output for a Tektronix 4014 CRT. The LRC graphics software is used in combination with the interface between this software and the PLOT 10 software.

Ames, K. R.↗

NASA NTRS1984

Parameter studies of gear cooling using an automatic finites element mesh generator

The range of accuracies achieved in the gear tooth temperature using an automatic finite element mesh generator were investigated. Gear web contribution to the gear cooling process was studied by introducing a varying size hole at the center of the gear because of the versatility of program TARG in allowing different heat transfer coefficients in different areas of the gear tooth. A study was carried out to evaluate the contribution of the loaded and unloaded faces as well as the top and bottom lands. A general purpose two-dimensional finite element preprocessor ATOGEN has been developed for automatic generation of a finite element mesh over a pie-shaped sector of a gear. The program was used for facilitating the input to an upgraded version of a previously developed program for the thermal analysis of running gears (TARG). The latter program determined the steady state temperature distribution throughout the specified gear. The automatic mesh generator program includes a band width minimization routine for reducing computer cost.

El-Bayoumy, L. E.↗

NASA NTRS1984

Computer generated animation and movie production at LARC: A case study

The process of producing computer generated 16mm movies using the MOVIE.BYU software package developed by Brigham Young University and the currently available hardware technology at the Langley Research Center is described. A general overview relates the procedures to a specific application. Details are provided which describe the data used, preparation of a storyboard, key frame generation, the actual animation, title generation, filming, and processing/developing the final product. Problems encountered in each of these areas are identified. Both hardware and software problems are discussed along with proposed solutions and recommendations.

Gates, R. L.↗

NASA NTRS1982

Noniterative grid generation using parabolic difference equations for fuselage-wing flow calculations

A fast method for generating three-dimensional grids for fuselage-wing transonic flow calculations using parabolic difference equations is described. No iterative scheme is used in the three-dimensional sense; grids are generated from one grid surface to the next starting from the fuselage surface. The computational procedure is similar to the iterative solution of the two-dimensional heat conduction equation. The proposed method is at least 10 times faster than the elliptic grid generation method and has much smaller memory requirements. Results are presented for a fuselage and wing of NACA-0012 section and thickness ratio of 10 percent. Although only H-grids are demonstrated, the present technique should be applicable to C-grids and O-grids in three dimensions.

Nakamura, S.↗