Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FORCES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Experimental measurements of hydrodynamic radial forces and stiffness matrices for a centrifugal pump-impeller

Measurements of the steady-state hydrodynamic forces on a centrifugal pump impeller are presented as a function of position within two geometrically different volutes. These correspond to the forces experienced by the impeller at zero whirl frequency. The hydrodynamic force matrices derived from these measurements exhibit both diagonal and off-diagonal terms of substantial magnitude. These terms are of the form which would tend to excite a whirl motion in a rotordynamic analysis of the pump; this may be the cause of 'rough running' reported in many pumps. Static pressure measurements in the impeller discharge flow show that the hydrodynamic force on the impeller contains a substantial component due to the nonisotropy of the net momentum flux leaving the impeller. A similar breakdown of the contributions to the stiffness matrices reveals that the major component of these matrices results from the nonisotropy of the momentum flux.

Chamieh, D. S.↗

Identification of nonlinear structural elements by force-state mapping

A major contributor to the passive damping and potentially nonlinear behavior of large space structures is the behavior of the joints. Proposed is an experimental technique called 'force-state mapping' that will allow ground testing of these key structural elements. The technique includes the use of very accurate instrumentation to measure the force transmission properties of a structural element as a function of its mechanical state. When these data are presented in the form of a force-state map, the nonlinearities exhibit distinctively recognizable patterns. This presentation of the data allows the extraction of the describing parameters of the linear and nonlinear behavior and the energy dissipation characteristics of the joint. A series of tests were carried out on an idealized laboratory test article to demonstrate the technique. Strong structural nonlinearities, including a cubic hardening spring, friction, and impact phenomena, were introduced and measured. Parameters identified by the force-state mapping technique are compared with those made by traditional techniques and the errors involved in the measurement are estimated.

Crawley, E. F.↗

Equilibrium of magnetic fields with arbitrary interweaving of the lines of force. I - Discontinuities in the torsion

Consideration is given to the static force-free equilibrium of a magnetic field in which all of the lines of force connect without knotting between parallel planes. The field is formed by continuous deformation from an initial uniform field, and is conventiently described in terms of the scalar function psi, which is the stream function for the incompressible wrapping and interweaving of the lines of force. Local compression and expansion of the lines of force is described in terms of the scalar function Phi. Equilibrium in the field requires satisfaction of two independent equations which cannot be accomplished without the full freedom of both psi and Phi. It is shown that discontinuities in the torsional characteristics of the lines occur when psi is predetermined by an arbitrary pattern. Discontinuities in the winding pattern of the lines can lead to discontinuities in the associated current sheets.

Parker, E. N.↗

Head movements in non-terrestrial force environments elicit motion sickness - Implications for the etiology of space motion sickness

Space motion sickness has become an operational concern in manned space flight. Considerable evidence exists that head movements in free fall, especially pitch movements, are provocative until adaptation occurs. The question arises whether space motion sickness is an unique nosological entity or is due to body movements in a nonterrestrial force environment, a force environment for which the body's dynamic sensory-motor adaptions to 1 G are no longer appropriate. To evaluate this issue, subjects were asked to make controlled head movements during exposure to high gravitoinertial force levels, 1.8-2.0 G, in parabolic flight maneuvers. Head movements in pitch with eyes open were most evocative of motion sickness, yaw movements with eyes covered were least provocative. This pattern is identical to that which occurs when the same types of head movements are made in the free fall phase of parabolic maneuvers. It appears that space motion sickness is the consequence of prolonged exposure to a nonterrestrial force background rather than of exposure to free fall per se.

Lackner, J. R.↗

Atmospheric tidal forcing of the zonal-mean circulation - The Martian dusty atmosphere

Classical atmospheric tidal theory has been used to compute the bilinear tidal zonal-mean forcing per unit mass of the zonal-mean meridional and zonal winds, together with the tidal zonal-mean heating per unit mass for the dusty Martian atmosphere. The convergences of the tidal Eliassen-Palm (EP) flux have been computed for both clear and dusty atmospheric conditions, including the special case of a 'dusty corridor' in the summer southern subtropics that is meant to simulate the early stages of a planetary-scale Martian dust storm. The calculation of the tidal EP zonal forcing differs from Hamilton in that more realistic thermotidal forcings and basic state temperatures are used. The zonal-mean convergences of the tidal fluxes of heat and momentum are large during a Martian great dust storm and should alter significantly the zonal-mean circulation and its residual component driven by the zonal-mean heating. In particular, the tidal forcing of the meridional wind, which is an order of magnitude greater than its zonal counterpart, is likely to give rise to a complex pattern of significantly ageostrophic zonal-mean flow in the Martian tropics.

Zurek, R. W.↗

Microprocessor controlled force actuator

The mechanical and electrical design of a prototype force actuator for vibration control of large space structures (LSS) is described. The force actuator is an electromagnetic system that produces a force by reacting against a proof-mass. The actuator has two colocated sensors, a digital microcontroller, and a power amplifier. The total weight of actuator is .998 kg. The actuator has a steady state force output of approximately 2.75 N from approximately 2 Hz to well beyond 1000 Hz.

Zimmerman, D. C.↗

Identification of nonlinear system parameters in joints using the force-state mapping technique

A procedure is presented for identifying the potentially strong nonlinear properties of structural members, such as joints, by expressing the force transmitted by the member as a function of its mechanical state. By explicitly including position and rate dependent effects, the surface of transmitted force versus state, the force-state map, has distinct, unique, superposable features for common structural nonlinearities, even those which appear to indicate hysteresis on a force-stroke presentation. An analysis is performed on the influence of true memory effects, transient response, and uncertainty in the measurements and system mass on the precision of the procedure. The successful identification of simulated data verifies the accuracy of the identification algorithm. Tests are then conducted on three actual joint models, with incomplete state measurements typical of an actual testing environment. The ability of the procedure to estimate the complete state vector and to analyze and reconstruct the measured nonlinear characteristics is demonstrated.

Crawley, E. F.↗

Blade-Tip-Clearance Forces in Turbines

Study reviews field and proposes experiments. Report summarizes present knowledge and discusses plans for experiments on blade-tipclearance excitation forces in turbines. Of particular interest Alford forces, named after pioneering worker in this field. These are cross forces due to uneven clearances, which in turn caused by and also cause rotor vibrations. Because blade-tip clearances affect turbine efficiency and excitation forces affect rotor stability, report proves useful to researchers and designers of advanced turbomachinery.

Martinez-Sanchez, M.↗

Experimental study of unsteady hydrodynamic force matrices on whirling centrifugal pump impellers

An experimental facility was constructed and instrumented. A set of centrifugal flow pumps whose impellers were made to follow a controlled circular whirl motion were studied. The aim was to characterize the steady and unsteady fluid forces measured on the impeller under various pump operating conditions. The postulation was that the unsteady lateral forces result from interactions between the impeller and the surrounding diffuser and/or volute (via the working fluid), and that under certain flow regimes these forces can drive unstable lateral motions of the pump rotor. The lateral hydrodynamic forces were decomposed into their steady and unsteady parts, the latter being further expressed in terms of a generalized fluid stiffness matrix. Conclusions regarding the effect of impeller geometry could not be reached given the similarity of the tested designs. However, other results on phenomena such as skin friction and leakage flow are presented. Some of the findings are compared to experimental and theoretical data from other sources. Finally, the rotordynamic consequences of the results are discussed as the present data were applied to the case of the Space Shuttle Main Engine (SSME) High Pressure Oxidizer Turbopump (HPOTP).

Belgacem, Jery↗

Calculation of forces on magnetized bodies using COSMIC NASTRAN

The methods described may be used with a high degree of confidence for calculations of magnetic traction forces normal to a surface. In this circumstance all models agree, and test cases have resulted in theoretically correct results. It is shown that the tangential forces are in practice negligible. The surface pole method is preferable to the virtual work method because of the necessity for more than one NASTRAN run in the latter case, and because distributed forces are obtained. The derivation of local forces from the Maxwell stress method involves an undesirable degree of manipulation of the problem and produces a result in contradiction of the surface pole method.

Sheerer, John↗

Forebody and missile side forces and the time analogy

A review of the 2-D, impulsively started cylinder literature is given to identify a number of physical parameters that can impact the nondimensional time at which vortex asymmetries begin. These parameters are then related to 3-D testing and explain the lack of data repeatability. The implications of these parameters on 3-D computational modeling is also discussed. An ad hoc form of the time analogy is then used to analyze and organize a slender body data base. An important result of the analysis is that the sectional side force in the nose region is a key to understanding the side force behavior for the configuration as a whole. The nose side force at the first pressure station is shown, for the data analyzed, to uniquely determine the rest of the side force development for laminar flow and to correlate with roll orientation independent of angle of attack and Reynolds number.

Hall, Robert M.↗

Distribution of resistive body-force in curved free-surface flow

The customary procedure for including resistive effects in turbulent hydraulic and stratified atmospheric flows is to integrate the empirically-known boundary shears over the entire wetted boundary of a thin fluid slab. A resistive body-force is then assumed to exist everywhere in each slab to replace the boundary shearing force. For the classical Saint-Venant (1871) model, this body-force can be shown to have a constant distribution in the vertical direction, and therefore can be evaluated for use in the momentum differential equation. In the newer Dressler theory (1978), however, for unsteady flow over curved beds, it is proved here that a constant body-force distribution is not possible. Its variable distribution is determined as well as its magnitude for use in the curved-flow equations. This variable distribution acts to produce an equal resultant in every thin layer of fluid parallel to the bed in an angular wedge over the curved channel bed. The new curved-flow equations are therefore extended to include resistive effects.

Sivakumaran, N. S.↗

Multiple-mode nonlinear free and forced vibrations of beams using finite element method

Effects of large deflection geometric nonlinearity and multiple modes for free and forced vibrations of beams are investigated. Inplane displacement and inplane inertia are included in the formulation. The finite element method is employed. A harmonic force matrix is derived for forced vibration analysis. The relations of amplitude, frequency ratio and forcing intensity for beams of different boundary conditions and various load conditions are presented.

Mei, Chuh↗

Effects of forced and free convections on structural temperatures of Space Shuttle Orbiter during reentry flight

Structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat transfer analysis of the Space Shuttle Orbiter wing subjected to reentry aerodynamic heating. With sufficient external forced convective cooling near the end of the heating cycle, the calculated surface temperatures of the thermal protection system (TPS) agree favorably with the flight data for the entire flight profile. However, the effects of this external forced convective cooling on the structural temperatures were found to be negligible. Both free convection and forced convection elements were introduced to model the internal convection effect of the cool air entering the Shuttle interior. The introduction of the internal free convection effect decreased the calculated wing lower skin temperatures by 20 F at most, 1200 sec after touchdown. If the internal convection is treated as forced convection, the calculated wing lower skin temperatures after touchdown can be reduced to match the flight-measured data very closely. By reducing the TPS thicknesses to certain effective thickness to account for the TPs gap heating, the calculated wing lower skin temperatures prior to touchdown can be raised to agree with the flight data perfectly.

Ko, William L.↗

On the glitches in the force transmitted by an electrodynamic exciter to a structure

Around resonance, the force transmitted by an exciter into a structure will be smaller or greater than a reference force generated by its coils due to electromechanical interaction. A simple analysis is presented which reveals how this phenomenon of force drop-off is controlled by three factors. The first factor, called Armature Mass Factor, describes a purely mechanical interaction between the structure and the exciter. The electromechanical energy conversion and its interaction with the structure yields two additional factors, called Electrical Resistance and Electrical Inductance Factors. They describe the effects of coil resistance, inductance and magnetic field strength relative to structural damping and stiffness. Present analysis indicates that, under proper circumstances, more than 90 percent of the force drop-off can be eliminated if armature-to-structure mass ratio is smaller or equal to half of modal loss factor.

Rao, Dantam K.↗

Aeroelastic forced response analysis of turbomachinery

An introduction is given to the research activity that is underway to enable the prediction of turbomachinery aeroelastic forced response. An effort is being made to assemble a computer program (FREPS) which incorporates the aeroelastic structural models, unsteady aerodynamic models, and forcing function models. The structural and aerodynamic models are currently well developed. The forcing function models are at a primitive level. A significant activity has begun to identify the forcing functions due to stator-rotor aerodynamic interaction.

Smith, Todd E.↗

The influence of gravitoinertial force level on oculomotor and perceptual responses to Coriolis, cross-coupling stimulation

The goal of the present experiment was to determine whether gravitoinertial force magnitude influences oculomotor and perceptual responses to Coriolis cross-coupling stimulation. Blindfolded subjects who were rotating at constant velocity were asked to make standardized head movements during the free-fall and high-force phases of parabolic flight, and the characteristics of their horizontal nystagmus and the magnitude of their experienced self-motion were measured. Both responses were less intense in the free-fall periods than in the high-force periods. These findings suggest that the response to semicircular canal stimulation depends on the background level of gravitoinertial force.

Dizio, Paul↗

Boundary force method for analyzing two-dimensional cracked plates

The Boundary Force Method (BFM) was formulated for the two-dimensional stress analysis of complex crack configurations. In this method, only the boundaries of the region of interest are modeled. The boundaries are divided into a finite number of straight-line segments, and at the center of each segment, concentrated forces and a moment are applied. This set of unknown forces and moments is calculated to satisfy the prescribed boundary conditions of the problem. The elasticity solution for the stress distribution due to concentrated forces and a moment applied at an arbitrary point in a cracked infinite plate are used as the fundamental solution. Thus, the crack need not be modeled as part of the boundary. The formulation of the BFM is described and the accuracy of the method is established by analyzing several crack configurations for which accepted stress-intensity factor solutions are known. The crack configurations investigated include mode I and mixed mode (mode I and II) problems. The results obtained are, in general, within + or - 0.5 percent of accurate numerical solutions. The versatility of the method is demonstrated through the analysis of complex crack configurations for which limited or no solutions are known.

Tan, Paul W.↗