Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Early Test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Final Report on Radiation Measurements Performed Inside of the BEAM Module

Measurements of the radiation environment inside of the Bigelow Expandable Activity Module (BEAM) have been made on a pseudo-continuous basis since June 6, 2016 using both passive and active instrumentation. Passive detectors yield a single cumulative dose value (or average daily dose) over the measurement period from deploy to return to ground. Active Radiation Environment Monitor (REM) sensors yield dose rate, Linear Energy Transfer (LET) spectra, and particle-specific dose, all on a 1-minute cadence. From the initial install in 2016 until early 2018, BEAM was an empty module. In 2018, further testing was approved and stowage began to be moved into BEAM. As a result, it was decided to stop measurements with RAM detectors to avoid potential difficulties with access after stowage was added. The REM sensors remained however in the original deploy locations.

radiation exposure↗

The Origin of Palimpsests

Palimpsests are the most enigmatic impact features observed on icy worlds of the Solar System. Palimpsests are large impact features which are bright, old, mostly flat, and roughly circular. They range from >150 to ~350 km in diameter and sometimes exhibit recognizable associated radial secondary ejecta crater strings beyond their rims. Curiously, among all the Solar System's icy worlds, palimpsests are exclusively seen on the icy Galilean moons. Palimpsests are obviously different than similarly sized impact features seen on other icy satellites. For example, Evander, a 350 km diameter peak-ring impact basin on Saturn’s moon Dione, has a very low depth/diameter ratio of 0.008, indicating significant viscous relaxation. Nevertheless, it still retains short wavelength topography including a prominent central peak, peak ring, and a continuous rim, none of which are seen at palimpsests. Palimpsests display an approximately circular, and dominating, expanse of undulating plains, which is level with surrounding terrain and shows no recognizable rim. At the center of palimpsests are smooth central plains that are enclosed by a low scarp. Central plains material superposes the surrounding undulating plains and is littered with small blocks reminiscent of “small chaos” on Europa. Palimpsests have yet to be explored using modern impact simulation tools. We have begun to investigate two competing hypotheses: (A) Palimpsests form on targets which have a preexisting near-subsurface layer that is liquid or solid but very weak, and is excavated as proximal ejecta; or (B) They form in a solid ice target underlain by a steep thermal gradient that strongly influences the resulting impact feature, including the production of impact-induced melting at depth that is then a major component of proximal ejecta. Our results will have profound implications for the early thermal history of the icy Galilean satellites. We will test our two hypotheses for the formation of palimpsests on Ganymede (where they are both best observed and preserved) by means of 2D iSALE hydrodynamic simulations of impacts into ice targets that will be structured according to the scenarios for each hypothesis, with select runs in 3D. We have already conducted a pilot study using 2D iSALE that has yielded promising results, which we will report out at the meeting.

palimpsests↗

Evaluating the Durability of Balance of Systems Components Using Combined-Accelerated Stress Testing

The degradation of photovoltaic (PV) balance of systems (BoS) components is not well-studied, but the consequences include offline modules, strings, and inverters; system shutdown; arc faults; and fires. A utility provider experienced a ~30% failure rate in their power transfer chain, originally attributed to branch connectors. Field-failed specimen assemblies were therefore examined, consisting of cable connector, branch connector, and discrete fuse components. Previous papers and presentations have focused on the development of the test method using a benchtop prototype. This presentation covers the early results of C-AST aging of static and dynamic specimens.

balance of systems↗

Accelerating the Decommissioning of the Sellafield Pile Fuel Storage Pond Using Innovative Remote Tooling Developed with the Supply Chain - 16437

The Pile Fuel Storage Pond (PFSP) at Sellafield and adjoining de-canning building provided the storage, cooling and de-canning facility for used fuel and isotopes from the two Windscale reactors and later some Magnox fuel from the Calder Hall reactors. Operations ceased in the 1970's and the facilities are now undergoing a programme of accelerated decommissioning. The pond is a sub-divided outdoor storage pond containing skips of irradiated fuel and miscellaneous waste items and the building contains a series of sub-ponds, known as bays, connected underwater to the main pond. The radiation environment and access limitations necessitate the use of remote technology for the decommissioning programme. This paper describes the philosophy and approach and the technology and equipment adopted for the removal and export of key plant equipment and waste items from within the PFSP. In order to progress the project cost effectively and speedily, the Sellafield project team looked for partners in the supply chain with the required experience, expertise and facilities to supply and test 'commercial off-the-shelf' (COTS) or modified proprietary equipment. This COTS approach minimised the need for multiple, expensive and lengthy design and manufacturing tasks associated with bespoke equipment. Sellafield partnered with specialist remote handling contractor, James Fisher Nuclear, and the respective project teams worked closely together at every stage of the project from qualifying requirements, identifying potential solutions, through to development, testing, training and final deployment. Optioneering of potential solutions involved early 'proof of principle' trials in JFN rig hall facilities, utilising existing equipment and plant mock-ups, along with other equipment manufactured in-house. Together the project teams selected the best solution to take forward, adopting a practical and trials based approach, which allowed rapid and cost effective modification of the solution throughout the project with minimal impact on the programme. When the final solution was validated, plant operators then gained familiarity and training on the equipment so they could execute the work efficiently on plant and so minimise their dose uptake. The removal of a Large De-canner is described in detail. This was a significant obstruction to the emptying, modification and re-use of the bay and a key milestone in the clean-up of the PFSP. The de-canners are large and heavy pieces of equipment which weigh 6.5 t each and approximately 6.5 m long. Their removal was further complicated by limited equipment and man access, radiological contamination from de-canning fuel, challenging material properties, unknown equipment condition and complex lifting requirements. Sellafield Ltd and JFN project teams worked closely together to rapidly develop, trial and deploy a succession of adapted 'commercial off-the-shelf' (COTS) tools whilst addressing emerging challenges and completing the overall task on time and budget. The Sellafield and JFN project and design teams provided an underwater: wheel stop removal tool; towing trolley; grinder on a carbon fibre pole, chute cutting 600 mm circular saw and hydraulic 6 t winch. The suite of tools will be reused on the remaining de-canners in the PFSP and First Generation Magnox Fuel Storage Pond (FGMSP) giving cost and programme savings. Each of the tools can also be used, and some have already been, for other tasks in the bay retrievals such as the size reduction of support frames, large steel sections and chemical de-canner preparatory works. The 'learning from experience' acquired during the project was shared by the Sellafield project with other decommissioning projects across the site. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2008 Co2 Assimilation in Plants: Genome to Biome Gordon Research Conference - August 17-22

Formerly entitled 'CO2 Fixation and Metabolism in Green Plants', this long-standing Gordon Research Conference has been held on a triennial basis since 1976. In 1990 the participants decided to alternate between sites in the U.S. and outside the U.S. The 2005 conference was held in Europe at the Centre Paul Langevin in Aussois, France, so the 2008 conference returns to a U.S. site - the University of New England in Biddeford, Maine. The 2008 conference covers basic plant research related to photosynthesis and the subsequent regulation and engineering of carbon assimilation. Approaches that range from post-genomic technologies and systems biology, through to fundamental biochemistry, physiology and molecular biology are integrated within ecological and agronomic contexts. As such, the meeting provides the rare opportunity of a single venue for discussing all aspects of the 'carbon-side' of photosynthesis - from genome to biome. The 2008 conference will include an emphasis on the central role of carbon assimilation by plants for developing new sources of bioenergy and for achieving a carbon-neutral planet. A special characteristic of this conference is its 'intimacy' with approximately 110 conferees, ranging from beginning graduate students and postdoctoral associates to leading senior plant scientists, engaged in open and forward-thinking discussions in an informal, friendly setting. With extended time devoted to discussion, and the encouragement to challenge dogma, it is unlike other meetings in the U.S. or abroad. Another novel feature of the conference is a session devoted to the latest 'hot off the press' findings by both established and early career scientists, picked from the abstracts. Together with an expanded poster discussion in the evening sessions, this session provides an opportunity for early career scientists to present interesting new data and to 'test drive' hypotheses in a collegial atmosphere.

99 GENERAL AND MISCELLANEOUS↗

Monitoring Thermal Fatigue Damage In Nuclear Power Plant Materials Using Acoustic Emission

Proactive aging management of nuclear power plant passive components requires technologies to enable monitoring and accurate quantification of material condition at early stages of degradation (i.e., pre-macrocrack). Acoustic emission (AE) is well-suited to continuous monitoring of component degradation and is proposed as a method to monitor degradation during accelerated thermal fatigue tests. A key consideration is the ability to separate degradation responses from external sources such as water spray induced during thermal fatigue testing. Water spray provides a significant background of acoustic signals, which can overwhelm AE signals caused by degradation. Analysis of AE signal frequency and energy is proposed in this work as a means for separating degradation signals from background sources. Encouraging results were obtained by applying both frequency and energy filters to preliminary data. The analysis of signals filtered using frequency and energy provides signatures exhibiting several characteristics that are consistent with degradation accumulation in materials. Future work is planned to enable verification of the efficacy of AE for thermal fatigue crack initiation detection. While the emphasis has been placed on the use of AE for crack initiation detection during accelerated aging tests, this work also has implications with respect to the use of AE as a primary tool for early degradation monitoring in nuclear power plant materials. The development of NDE tools for characterization of aging in materials can also benefit from the use of a technology such as AE which can continuously monitor and detect crack initiation during accelerated aging tests.

acoustic emission↗

Aerofoil testing in a self-streamlining flexible walled wind tunnel

Two-dimensional self-streamlining flexible walled test sections eliminate, as far as experimentally possible, the top and bottom wall interference effects in transonic aerofoil testing. The test section sidewalls are rigid, while the impervious top and bottom walls are flexible and contoured to streamline shapes by a system of jacks, without reference to the aerofoil model. The concept of wall contouring to eliminate or minimise test section boundary interference in two-dimensional testing was first demonstrated by the National Physical Laboratory (NPL) in England during the early 1940's. The transonic streamlining strategy proposed, developed and used by NPL has been compared with several modern strategies. The NPL strategy has proved to be surprisingly good at providing a wall interference-free test environment, giving model performance indistinguishable from that obtained when using the modern strategies over a wide range of test conditions. In all previous investigations the achievement of wall streamlining in flexible walled test sections has been limited to test conditions up to those which result in the model's shock just extending to a streamlined wall. This work, however, has also successfully demonstrated the feasibility of two-dimensional wall streamlining at test conditions where both model shocks have reached and penetrated through their respective flexible walls. Appropriate streamlining procedures have been established and are uncomplicated, enabling flexible walled test sections to easily cope with these high transonic flows.

Mark Charles Lewis↗

Parameters of tensile strength, elongation, and tenacity of 70mm IIaO spectroscopic film

The 70mm IIaO spectroscopic film was tested to determine its tensile strength, elongation, and breaking strength, using an Instron (strength and compression) 4201 Test Instrument. These data provide information leading to the upper and lower limits of the above parameters for 70mm IIaO spectroscopic film. This film will be developed by a commercial developing machine after the Ultraviolet Telescope Space Shuttle Mission returns to the Earth in the early 1990's; thus, it is necessary to understand these force parameters. Several test strips of approximately 200mm in length were used. The results indicate that when a stress load of 100 kg was applied, the film elongated approximately 1.06mm and the break strength was 19.45 kilograms.

Hammond, Ernest C., Jr.↗

Qualification of the Flight Heaters for the NEXT-C Hollow Cathodes

After successful validation of the design, swaged cathode heaters have been delivered by the NASA Glenn Research Center to Aerojet Rocketdyne for the fabrication of the NEXT-C ion thruster. NASA Glenn Research Center re-established and validated process controls as well as completed cyclic life testing of development heaters. Following an extensive requalification program, fabrication of a flight batch of heaters was executed using the qualified process controls. Of the 28 heaters fabricated in this flight batch, a set of six heaters were acceptance and cyclic tested to verify conformance with operational requirements. Upon completion of 200 percent of the NEXT-C cyclic requirement, the heater batch was certified by NASA for use in the flight hollow cathodes. Nine heaters from the batch of 28 were provided to Aerojet Rocketdyne in early 2018 for cathode fabrication. This paper summarizes the acceptance and cyclic life testing of the flight heaters and preliminary findings of post-test analyses.

Arthur, Neil↗

Qualification of the Flight Heaters for the NEXT-C Hollow Cathodes

After successful validation of the design, swaged cathode heaters have been delivered by the NASA Glenn Research Center to Aerojet Rocketdyne for the fabrication of the NEXT-C ion thruster . NASA Glenn Research Center re-established and validated process controls as well as completed cyclic life testing of development heaters. Following an extensive requalification program, fabrication of a flight batch of heaters was executed using the qualified process controls. Of the 28 heaters fabricated in this flight batch, a set of six heaters were acceptance and cyclic tested to verify conformance with operational requirements. Upon completion of 200 percent of the NEXT-C cyclic requirement, the heater batch was certified by NASA for use in the flight hollow cathodes. Nine heaters from the batch of 28 were provided to Aerojet Rocketdyne in early 2018 for cathode fabrication. This paper summarizes the acceptance and cyclic life testing of the flight heaters and preliminary findings of post-test analyses.

Arthur, Neil↗

QualifiCation of the Flight Heaters for the NEXT-C Hollow Cathodes

After successful validation of the design, swaged cathode heaters have been delivered by the NASA Glenn Research Center to Aerojet Rocketdyne for the fabrication of the NEXT-C ion thruster . NASA Glenn Research Center re-established and validated process controls as well as completed cyclic life testing of development heaters. Following an extensive requalification program, fabrication of a flight batch of heaters was executed using the qualified process controls. Of the 28 heaters fabricated in this flight batch, a set of six heaters were acceptance and cyclic tested to verify conformance with operational requirements. Upon completion of 200 percent of the NEXT-C cyclic requirement, the heater batch was certified by NASA for use in the flight hollow cathodes. Nine heaters from the batch of 28 were provided to Aerojet Rocketdyne in early 2018 for cathode fabrication. This paper summarizes the acceptance and cyclic life testing of the flight heaters and preliminary findings of post-test analyses.

Arthur, Neil↗

Tests of highly loaded skids on a concrete runway

Skids have been used at various times for aircraft landing gear ever since the Wright Flyer appeared in the early 1900's. Typically, skids have been employed as aircraft landing gear either at low speeds or at low bearing pressures. Tests were conducted to examine the friction and wear characteristics of various metals sliding on a rough, grooved concrete runway. The metals represented potential materials for an overload protection skid for the Space Shuttle orbiter. Data from tests of six skid specimens conducted at higher speeds and bearing pressures than those of previous tests in the open literature are presented. Skids constructed of tungsten with embedded carbide chips exhibited the lowest wear, whereas a skid constructed of Inconel 718 exhibited high wear rates. Friction coefficients for all the skid specimens were moderate and would provide adequate stopping performance on a long runway. Because of its low wear rate, a skid constructed of tungsten with embedded carbide chips is considered to be a likely candidate for an aircraft skid or overload protection skid.

Stubbs, Sandy M.↗

Radiation Effects Considerations for Instrumentation and Control in Space Nuclear Systems

Radiation effects in electrical, electronic, electro-motive, and electro-optical (EEEE) hardware encompass a complex variety of interactions, processes, environments, and an evolving landscape of relevant hardware. Appropriately mitigating the effects of radiation in sensors, data acquisition, and control hardware is among the most significant challenges associated with deploying space nuclear power and propulsion systems. The expertise within EEEE radiation effects disciplines require working knowledge that is at least as complex and diverse as the problem itself, but that should not dissuade stakeholders and engineers in adjacent disciplines from attempting to understand the general principles associated with the problem at hand. This brief overview seeks to bring to the foreground a set of relevant topics that are of special importance for space nuclear propulsion applications that involve high rates of neutron and gamma radiation. The unique set of environments and design requirements for space nuclear systems mean that the experience and utility for methods applied to typical spaceflight hardware or terrestrial nuclear systems must not be applied naively. Forward consideration on the applicability of testing methods applied to either existing or bespoke hardware is likely to drive early decisions on system-wide radiation effects mitigation strategies, and will influence procurement requirements for providers of radiation tolerant hardware who are unlikely to have experience in this unique set of environments. Radiation hardness assurance (RHA) guidance should be adapted and emphasize the importance of hardware testing in the relevant environment. These must consider the combined effects of temperature, total ionizing dose (TID), non-ionizing/displacement damage (TNID/DD), and single event effects (SEE), and should consider the impacts of flux (rate) in addition to cumulative effects.

Radiation↗

Oxidation and Extraction of Americium(VI) from Lanthanides

Partitioning and transmutation of americium and curium has been the subject of significant research in the nuclear fuel cycle over the past two decades. Numerous approaches have been studied to separate these elements from the lanthanide elements to enable their recycle and transmutation. Americium is one of the primary long-term heat sources in used nuclear fuel, which may impact repository loading. The lanthanides are both a) neutron poisons, reducing reactor performance, if recycled, and b) can chemically interact with fuel cladding to cause early failure, if present in sufficient concentration. Chemical separation approaches for heterogeneous fuel recycle, typically utilize proven technology (PUREX or modifications to the PUREX process) to remove uranium and plutonium from the dissolved fuel (and if desired, can remove neptunium as well). Follow-on processing is then required to separate the americium and curium, or the americium alone (for target fabrication). In a homogeneous recycle approach, the bulk of the uranium is typically separated first, followed by additional processing to remove the transuranic elements as a group. Because of the chemical similarity of the americium with the lanthanides, and particularly with curium, these separate processes are difficult. Utilizing the unique valence states of americium (primarily the (VI) oxidation state), opens up new opportunities for the separation of americium for either heterogeneous recycle (enabling americium separation alone) or homogeneous recycle (separating americium together with plutonium and neptunium). The US Department of Energy Fuel Cycle Technologies program has been researching methods to oxidize americium and to extract it from lanthanides as americium(VI), preferably from molar nitric acid solutions. Early efforts identified sodium bismuthate as an effective oxidant, which enabled testing of the extraction of americium(VI) by tributyl phosphate and diamylamylphosphonate. Successful extraction of americium(VI) was demonstrated in this system, in both batch contact laboratory tests and in centrifugal contactors; however, the sodium bismuthate is a solid, and must be in excess of saturation with the solution. This creates some engineering challenges in the process. A significant effort to identify alternative oxidants has led to a number of promising approaches. Silver-catalyzed ozone, copper(III) periodate, and electrochemical oxidation of americium from the trivalent to hexavalent state have all been successfully demonstrated in laboratory experiments. These approaches would enable oxidation and extraction of americium without having to filter solids. Once the americium is oxidized, a key issue is how long it will remain in the hexavalent state. Investigations have shown that some materials of construction (e.g., tantalum) do not reduce americium as quickly as stainless steel. Also, alternative extractants, such as amides, do not appear to reduce the americium as rapidly as the phosphate or phosphonate extractants. While still early in their development, these advances in the technology offer some positive indications that a workable extraction process for the separation of americium(VI) can be realized in the near future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Grace L Douglas↗

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Lichar Dillon↗

TechEdSat Nano-Satellite Series Fact Sheet

TechEdSat-3p is the second generation in the TechEdSat-X series. The TechEdSat Series uses the CubeSat standards established by the California Polytechnic State University Cal Poly), San Luis Obispo. With typical blocks being constructed from 1-unit (1U 10x10x10 cm) increments, the TechEdSat-3p has a 3U volume with a 30 cm length. The project uniquely pairs advanced university students with NASA researchers in a rapid design-to-flight experience lasting 1-2 semesters.The TechEdSat Nano-Satellite Series provides a rapid platform for testing technologies for future NASA Earth and planetary missions, as well as providing students with an early exposure to flight hardware development and management.

Platform for rapid technology testing↗

Tre-DST: A Drug Susceptibility Test for Mycobacterium tuberculosis Using Solvatochromic Trehalose Probes

In 2024, an estimated 10 million people developed Tuberculosis (TB), nearly half a million of whom were infected with drug-resistant tuberculosis (DR-TB). Early detection of infection and drug resistance enables rapid engagement in effective care. Bacterial culture and nucleic acid testing remain the primary diagnostic methods, with smear microscopy being phased out. However, these methods present significant limitations for diagnosing drug resistance, such as lengthy time-to-result for phenotypic tests, as well as the need for prior knowledge of resistance mutations and prohibitive cost for molecular tests. To address this, we developed a rapid phenotypic TB drug susceptibility test, termed Tre-DST, based on novel metabolically incorporated trehalose probes, which specifically detect live mycobacteria. We used the nonpathogenic Mycobacterium smegmatis and the virulence-attenuated Mycobacterium tuberculosis (Mtb) H37Ra or auxotrophic Mtb to demonstrate a strong correlation between cost-effective plate reader results and flow cytometry data, suggesting that the plate reader is a suitable fluorescence detector for Tre-DST. We determined that adding a 1-week incubation step allowed Mtb samples originally seeded at 10 4 CFU/mL to become detectable, over 2 weeks earlier than colony-forming unit analysis. We found that Tre-DST reports on drug susceptibility in a drug-agnostic manner, demonstrating loss of fluorescence with frontline TB drugs as well as the newer drug bedaquiline. Tre-DST distinguished RIF- and INH-resistant auxotrophs from susceptible controls and accurately reported the resistance activity. Ultimately, because Tre-DST is agnostic to mechanisms of drug resistance, this assay is likely compatible with all WHO-recommended and future DR-TB drugs as a diagnostic in reference laboratories.

diagnostics↗