Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Computational Geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Thermal modeling of the NASA-Ames Research Center Cryogenic Optical Test Facility and a single-arch, fused-natural-quartz mirror

A thermal model of the dewar and optical system of the Cryogenic Optical Test Facility at NASA-Ames Research Center was developed using the computer codes SINDA and MONTE CARLO. The model was based on the geometry, boundary conditions, and physical properties of the test facility and was developed to investigate heat transfer mechanisms and temperatures in the facility and in test mirrors during cryogenic optical tests. A single-arch, fused-natural-quartz mirror was the first mirror whose thermal loads and temperature distributions were modeled. From the temperature distribution, the thermal gradients in the mirror were obtained. The model predicted that a small gradient should exist for the single arch mirror. This was later verified by the measurement of mirror temperatures. The temperatures, predicted by the model at various locations within the dewar, were in relatively good agreement with the measured temperatures. The model is applicable to both steady-state and transient cooldown operations.

Ng, Y. S.↗
NASA NTRS1992

Computations of the unsteady flow about a generic wing/pylon/finned-store configuration

An overset grid approach is used to carry out a set of computations of the unsteady flow about a generic wing, pylon, and finned-store configuration. The geometry, discretization procedure, and governing equations are presented. Thin-layer Navier-Stokes solutions are presented for four store separation cases: store in carriage position, store at two different separation positions, and a time-accurate simulation of the forced store separation from the wing pylon carriage. Computational results are compared with wind tunnel data for the three 'static store' cases. Dynamic loads and trajectory data are presented for the forced separation case.

Meakin, Robert L.↗
NASA NTRS1992

Preliminary design of a high speed civil transport: The Opus 0-001

Based on research into the technology and issues surrounding the design, development, and operation of a second generation High Speed Civil Transport, HSCT, the Opus 0-001 team completed the preliminary design of a sixty passenger, three engine aircraft. The design of this aircraft was performed using a computer program which the team wrote. This program automatically computed the geometric, aerodynamic, and performance characteristic of an aircraft whose preliminary geometry was specified. The Opus 0-001 aircraft was designed for a cruise Mach number of 2.2, a range of 4,700 nautical miles and its design was based in current or very near term technology. Its small size was a consequence of an emphasis on a profitable, low cost program, capable of delivering tomorrow's passengers in style and comfort at prices that make it an attractive competitor to both current and future subsonic transport aircraft. Several hundred thousand cases of Cruise Mach number, aircraft size and cost breakdown were investigated to obtain costs and revenues for which profit was calculated. The projected unit flyaway cost was $92.0 million per aircraft.

Source record↗
NASA NTRS1992

Spectral bidirectional and hemispherical reflectance characteristics of selected sites in the Streletskaya steppe

Measurements of plant canopy bidirectional reflectance made by the PARABOLA (portable apparatus for rapid acquisition of bidirectional observations of the land and atmosphere) instrument in three spectral bands are analyzed for steppe grassland sites of differing productivity levels. The variation of spectral reflectance and the normalized difference vegetation index in the solar principal plane is presented. Comparisons are made with PARABOLA measurements from selected first ISLSCP field experiment (FIFE) grassland sites in the Konza prairie, Kansas. The Streletskaya steppe sites showed no strong hot spot reflectance, while this effect was present in some FIFE sites but absent in others. The hot spot effect seems to be dependent on canopy geometry and background reflectance characteristics of these sites. Spectral hemispherical reflectance was computed from the angular integration of the bidirectional measurements for the steppe sites. Total shortwave albedo was estimated from these hemispherical reflectance measurements and compared to albedo measured by pyranometers. The albedo estimates from PARABOLA were found to be approximately 12-17 percent higher than the pyranometer measurements.

Eck, Thomas F.↗
NASA NTRS1991

VLSI architectures for geometrical mapping problems in high-definition image processing

This paper explores a VLSI architecture for geometrical mapping address computation. The geometric transformation is discussed in the context of plane projective geometry, which invokes a set of basic transformations to be implemented for the general image processing. The homogeneous and 2-dimensional cartesian coordinates are employed to represent the transformations, each of which is implemented via an augmented CORDIC as a processing element. A specific scheme for a processor, which utilizes full-pipelining at the macro-level and parallel constant-factor-redundant arithmetic and full-pipelining at the micro-level, is assessed to produce a single VLSI chip for HDTV applications using state-of-art MOS technology.

Kim, K.↗
NASA NTRS2000

On the Coupling of CDISC Design Method with FPX Rotor Code

A rotor section aerodynamics design package is developed by coupling Constrained Direct Iterative Surface Curvature (CDISC) design method with the FPX rotor code. The coupling between the CDISC design and the FPX flow analysis is fully automated. The CDISC design method employs a predictor-corrector procedure iteratively to determine a surface geometry which produces a target pressure distribution, where the target pressure distributions is either pre-defined or automatically generated through flow and geometry constraints. The FPX code is an eXtended Full-Potential rotor Computational Fluid Dynamics (CFD) code, which solves the three-dimensional unsteady full-potential equation in a strong conservative form using an implicit approximate factorization finite-difference scheme with entropy and viscosity corrections. Application of the CDISC design method coupled with the FPX rotor code is made for rotor blades in hovering motions. Several design examples are presented to demonstrate the capability of the new package in rotor section design.

Hu, Hong↗
NASA NTRS2003

Numerical and Experimental Determination of the Geometric Far Field for Round Jets

To reduce ambiguity in the reporting of far field jet noise, three round jets operating at subsonic conditions have recently been studied at the NASA Glenn Research Center. The goal of the investigation was to determine the location of the geometric far field both numerically and experimentally. The combination of the WIND Reynolds-Averaged Navier-Stokes solver and the MGBK jet noise prediction code was used for the computations, and the experimental data was collected in the Aeroacoustic Propulsion Laboratory. While noise sources are distributed throughout the jet plume, at great distances from the nozzle the noise will appear to be emanating from a point source and the assumption of linear propagation is valid. Closer to the jet, nonlinear propagation may be a problem, along with the known geometric issues. By comparing sound spectra at different distances from the jet, both from computational methods that assume linear propagation, and from experiments, the contributions of geometry and nonlinearity can be separately ascertained and the required measurement distance for valid experiments can be established. It is found that while the shortest arc considered here (approx. 8D) was already in the geometric far field for the high frequency sound (St greater than 2.0), the low frequency noise due to its extended source distribution reached the geometric far field at or about 50D. It is also found that sound spectra at far downstream angles does not strictly scale on Strouhal number, an observation that current modeling does not capture.

Koch, L. Danielle↗
NASA NTRS2003

Modified Involute Helical Gears: Computerized Design, Simulation of Meshing and Stress Analysis

The computerized design, methods for generation, simulation of meshing, and enhanced stress analysis of modified involute helical gears is presented. The approaches proposed for modification of conventional involute helical gears are based on conjugation of double-crowned pinion with a conventional helical involute gear. Double-crowning of the pinion means deviation of cross-profile from an involute one and deviation in longitudinal direction from a helicoid surface. Using the method developed, the pinion-gear tooth surfaces are in point-contact, the bearing contact is localized and oriented longitudinally, and edge contact is avoided. Also, the influence of errors of alignment on the shift of bearing contact, vibration, and noise are reduced substantially. The theory developed is illustrated with numerical examples that confirm the advantages of the gear drives of the modified geometry in comparison with conventional helical involute gears.

COMPUTER AIDED DESIGN↗
NASA NTRS2004

Improving the Flow

In early 1995, NASA s Glenn Research Center (then Lewis Research Center) formed an industry-government team with several jet engine companies to develop the National Combustion Code (NCC), which would help aerospace engineers solve complex aerodynamics and combustion problems in gas turbine, rocket, and hypersonic engines. The original development team consisted of Allison Engine Company (now Rolls-Royce Allison), CFD Research Corporation, GE Aircraft Engines, Pratt and Whitney, and NASA. After the baseline beta version was established in July 1998, the team focused its efforts on consolidation, streamlining, and integration, as well as enhancement, evaluation, validation, and application. These activities, mainly conducted at NASA Glenn, led to the completion of NCC version 1.0 in October 2000. NCC version 1.0 features high-fidelity representation of complex geometry, advanced models for two-phase turbulent combustion, and massively parallel computing. Researchers and engineers at Glenn have been using NCC to provide analysis and design support for various aerospace propulsion technology development projects. NASA transfers NCC technology to external customers using non- exclusive Space Act Agreements. Glenn researchers also communicate research and development results derived from NCC's further development through publications and special sessions at technical conferences.

Source record↗
NASA NTRS2005

Mimicking Natural Laminar to Turbulent Flow Transition: A Systematic CFD Study Using PAB3D

For applied aerodynamic computations using a general purpose Navier-Stokes code, the common practice of treating laminar to turbulent flow transition over a non-slip surface is somewhat arbitrary by either treating the entire flow as turbulent or forcing the flow to undergo transition at given trip locations in the computational domain. In this study, the possibility of using the PAB3D code, standard k-epsilon turbulence model, and the Girimaji explicit algebraic stresses model to mimic natural laminar to turbulent flow transition was explored. The sensitivity of flow transition with respect to two limiters in the standard k-epsilon turbulence model was examined using a flat plate and a 6:1 aspect ratio prolate spheroid for our computations. For the flat plate, a systematic dependence of transition Reynolds number on background turbulence intensity was found. For the prolate spheroid, the transition patterns in the three-dimensional boundary layer at different flow conditions were sensitive to the free stream turbulence viscosity limit, the reference Reynolds number and the angle of attack, but not to background turbulence intensity below a certain threshold value. The computed results showed encouraging agreements with the experimental measurements at the corresponding geometry and flow conditions.

Pao, S. Paul↗
NASA NTRS1998

Mixing of Multiple Jets With a Confined Subsonic Crossflow

Results from a recently completed enhanced mixing program are summarized in the two technical papers. These studies were parts of a High Speed Research (HSR)-supported joint Government/industry/university program that involved, in addition to the NASA Lewis Research Center, researchers at United Technologies Research Center, Allison Engine Company, CFD Research Corporation, and the University of California, Irvine. The studies investigated the mixing of jets injected normal to a confined subsonic mainsteam in both rectangular and cylindrical ducts. Experimental and computational studies were performed in both nonreacting and reacting flows. The orifice geometries and flow conditions were selected as typical of the complex three-dimensional flows in the combustion chambers in low-emission gas turbine engines. The principal conclusion from both the experiments and modeling was that the momentum-flux ratio J and orifice spacing S/H were the most significant flow and geometry variables, respectively. Conserved scalar distributions were similar-independent of reaction, orifice diameter H/d, and shape-when the orifice spacing and the square root of the momentum-flux ratio were inversely proportional. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. We found that planar averages must be considered in context with the distributions. The mass-flow ratios and the orifices investigated were often very large. The jet-to-mainstream mass-flow ratio was varied from significantly less than 1 to greater than 1. The orifice-area to mainstream-cross-sectional-area was varied from approx. 0 to 0.5, and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. As an example of the results, the accompanying figure shows the effects of different rates of mass addition on the opposite walls of a rectangular duct.

Holdeman, James D.↗
NASA NTRS2014

Static Aeroelastic Analysis with an Inviscid Cartesian Method

An embedded-boundary, Cartesian-mesh flow solver is coupled with a three degree-of-freedom structural model to perform static, aeroelastic analysis of complex aircraft geometries. The approach solves a nonlinear, aerostructural system of equations using a loosely-coupled strategy. An open-source, 3-D discrete-geometry engine is utilized to deform a triangulated surface geometry according to the shape predicted by the structural model under the computed aerodynamic loads. The deformation scheme is capable of modeling large deflections and is applicable to the design of modern, very-flexible transport wings. The coupling interface is modular so that aerodynamic or structural analysis methods can be easily swapped or enhanced. After verifying the structural model with comparisons to Euler beam theory, two applications of the analysis method are presented as validation. The first is a relatively stiff, transport wing model which was a subject of a recent workshop on aeroelasticity. The second is a very flexible model recently tested in a low speed wind tunnel. Both cases show that the aeroelastic analysis method produces results in excellent agreement with experimental data.

Aeroelastic↗
NASA NTRS2019

Supersonic Engine Inlet Tone Noise Radiation

A computational and experimental acoustic analysis was conducted on a supersonic engine inlet geometry with a spike center body and an auxiliary inlet. Simulations performed using two different commercial acoustics software packages were compared to a scale model experiment conducted using an ultrasonic fan noise simulator. Both the experiment and simulations were run at discrete circumferential mode and frequency combinations to identify strengths and weaknesses of each method. For cases where a single azimuthal mode was well cut on throughout the length of the duct, reasonable agreement was found between the three methods. In cases with more complicated acoustic effects, the experimental results became intractable when considered alone and the simulations were needed for interpreting the results. The peak sound level and the peak angle of the far field radiation vary widely when changing modes and frequencies. The objective of the study is to develop a validated workflow for simulation of fan tone noise through supersonic inlet geometries for community noise predictions.

Stephens, David B.↗
NASA NTRS2019

An Analytic Model for Estimating the First Contact Resistance Needed to Avoid Damaging ESD During Spacecraft Docking in GEO

NASA’s Gateway program will involve spacecraft (s/c) docking in the outer radiation belt in order to transfer Gateway elements between s/c for transport to lunar orbit. The charging of these s/c to different potentials prior to docking raises the possibility of a damaging electrostatic discharge (ESD) at the time of first contact between the s/c. A proposed mitigation strategy is for first contact to occur prior to docking through a resistor with resistance R that would lower the potential difference at an optimal rate to a sufficiently low value to prevent ESD damage. The coupling of s/c by a resistor can be modeled by SPIS, but for realistic two s/c models SPIS can take hours to simulate the evolution of the s/c surface charges and potentials to an equilibrium state. Our objective is to develop a simpler model of s/c resistive coupling that runs orders of magnitude faster while providing useful first design estimates of the time variation of the s/c potentials, current through the resistor, and how these vary with R and s/c configuration This configuration is defined by the relative separation and orientation of the s/c, and their solar illumination. The configuration and geometry of the s/c determine their capacitive coupling. The s/c capacitances are computed using Nascap-2K. This poster presents the first version of such a model, and initial tests.

Goodman, Michael L.↗
NASA NTRS2019

An Analytic Model for Estimating the First Contact Resistance Needed to Avoid Damaging ESD During Spacecraft Docking in GEO

NASA’s Gateway program is to involve spacecraft (s/c) docking in the outer radiation belt in order to transfer Gateway elements between s/c for transport to lunar orbit. The charging of these s/c to different potentials prior to docking raises the possibility of a damaging electrostatic discharge (ESD) at the time of first contact between the s/c. A proposed mitigation strategy is for first contact to occur prior to docking through a resistor with resistance R that would lower the potential difference at an optimal rate to a sufficiently low value to prevent a damaging ESD. The coupling of s/c by a resistor can be modeled by SPIS (Spacecraft Plasma Interaction System), but for realistic two s/c models SPIS can take hours to simulate the evolution of the s/c surface charges and potentials to an equilibrium state. Our objective is to develop a simpler model of s/c resistive coupling that runs orders of magnitude faster while providing useful first design estimates of the time variation of the s/c potentials, current through the resistor, and how these vary with R and s/c configuration. This configuration is defined by the relative separation and orientation of the s/c, and their solar illumination. The configuration and geometry of the s/c determine their capacitive coupling. The s/c capacitances are computed using Nascap-2K. This abstract and the associated poster describe the first version of such a model, and initial tests.

Goodman, Michael L.↗
NASA NTRS2019

Advances in Space Radiation Physics and Transport

The space radiation environment is a complex mixture of particle types and energies originating from sources inside and outside of the galaxy. These environments may be modified by the heliospheric and geomagnetic conditions as well as planetary bodies and vehicle or habitat mass shielding. In low Earth orbit (LEO), the geomagnetic field deflects a portion of the galactic cosmic rays (GCR) and all but the most intense solar particle events (SPE). There are also dynamic belts of trapped electrons and protons with low to medium energy and intense particle count rates. In deep space, the GCR exposure is more severe than in LEO and varies inversely with solar activity. Unpredictable solar storms also present an acute risk to astronauts if adequate shielding is not provided. Near planetary surfaces such as the Earth, moon or Mars, secondary particles are produced when the ambient deep space radiation environment interacts with these surfaces and/or atmospheres. These secondary particles further complicate the local radiation environment and modify the associated health risks. Characterizing the radiation fields in this vast array of scenarios and environments is a challenging task and is currently accomplished with a combination of computational models and dosimetry. The computational tools include models for the ambient space radiation environment, mass shielding geometry, and atomic and nuclear interaction parameters. These models are then coupled to a radiation transport code to describe the radiation field at the location of interest within a vehicle or habitat. Many new advances in these models have been made in the last decade, and the present review article focuses on the progress and contributions made by workers and collaborators at NASA in the same time frame. Although great progress has been made, and models continue to improve, significant gaps remain and are discussed in the context of planned future missions. Of particular interest is the juxtaposition of various review committee findings regarding the accuracy and gaps of combined space radiation environment, physics, and transport models with the progress achieved over the past decade. While current models are now fully capable of characterizing radiation environments in the broad range of forecasted mission scenarios, it should be remembered that uncertainties still remain and need to be addressed.

Space radiation↗
NASA NTRSDate not supplied

A Large-Eddy Simulation Of Turbulent Flow Over A Backward Facing Step

Large-eddy simulation (LES) was used to study the turbulent flow over a backward facing step. The simulations examine the details of the turbulent flow’s separated and reattaching regions created by the step geometry. An explicit high-order of accuracy/high resolution finite-difference computational fluid dynamics solver was used for both LES and Reynolds-averaged Navier-Stokes (RANS) simulations. The experimental data from the backward facing step experiment of Driver and Seegmiller was used for comparison. Data presented are derived from a RANS simulation using the Spalart-Allmaras turbulence model and LES simulations using the implicit LES assumption on three different grids of varying resolution. The RANS solution agrees with past work. It does an adequate job of predicting the flowfield and reattachment point, but misses details such as the strength of the recirculating region and magnitudes of the Reynolds stresses. The synthetic eddy method was used to provide a turbulent inflow to the quasi-2D LES domains. For the LES, the coarse grid was of insufficient resolution and under-predicted the skin friction coefficient and over-predicted the normal stresses. The finer grid LES results accurately predict the skin friction coefficient and provide more accurate Reynolds stresses. Triple product velocity correlations are also computed from the LES and the finer grid results did a good job predicting the magnitudes of the curves and the shapes were reasonably represented. It is recommended that future work include investigating the turbulent inflow domain length, width of the quasi-2D domain, and additional grid refinement

turbulence↗
NASA NTRSDate not supplied

A Large-Eddy Simulation Of Turbulent Flow Over A Backward Facing Step

Large-eddy simulation (LES) was used to study the turbulent flow over a backward facing step. The simulations examine the details of the turbulent flow's separated and reattaching regions created by the step geometry. An explicit high-order of accuracy/high resolution finite-difference computational fluid dynamics solver was used for both LES and Reynolds-averaged Navier-Stokes (RANS) simulations. The experimental data from the backward facing step experiment of Driver and Seegmiller was used for comparison. Data presented are derived from a RANS simulation using the Spalart-Allmaras turbulence model and LES simulations using the implict LES assumption on three different grids of varying resolution. The RANS solution agrees with past work. It does an adequate job of predicting the flowfield and reattachment point, but misses details such as the strength of the recirculating region and magnitudes of the Reynolds stresses. The synthetic eddy method was used to provide a turbulent inflow to the quasi-2D LES domains. For the LES, the coarse grid was of insufficient resolution and under-predicted the skin friction coefficient and over-predicted the normal stresses. The finer grid LES results accurately predict the skin friction coefficient and provide more accurate Reynolds stresses. Triple product velocity correlations are also computed from the LES and the finer grid results did a good job predicting the magnitudes of the curves and the shapes were reasonably represented. It is recommended that future work include investigating the turbulent inflow domain length, width of the quasi-2D domain, and additional grid refinement.

turbulence↗