Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1962

Unitary Wind Tunnel Tests of 30-Degree Conical Ribbon Parachute and a Rotofoil Parachute Towed in the Wake of a Conical Nosed Cylindrical Body

Multiple wind tunnel test trials were conducted on a 30 degree conical ribbon parachute with porosities of 30, 27, and 24 percent. Variables were Mach number, dynamic pressure, towline length, and coefficient of drag. A Rotofoil parachute having a porosity of approximately 24 percent was tested, but failed after about 30 seconds of operation at a Mach number of 1.8 All of the parachutes had a nominal diameter and shroud line length of 10 inches. Drag coefficients were based on the area of a circle having a diameter two-thirds of the nominal parachute diameter.

WIND TUNNEL TESTS↗
NASA NTRS1973

March 1971 wind tunnel tests of the Dorand DH 2011 jet flap motor, volume 2

Wind tunnel tests were conducted of the Dorand DH 2011D jet flap rotor. The data recorded during the tests consist of: (1) multicyclic cam coefficients, (2) stress analysis, (3) vibratory loads, (4) Fourier analysis of flap deflection, and (5) blade bending stress. Data are presented in the form of tables and graphs.

Kretz, M.↗
NASA NTRS1975

Transonic wind tunnel tests of A.015 scale space shuttle orbiter model, volume 1

Transonic wind tunnel tests were run on a 0.015 scale model of the Space Shuttle Orbiter Vehicle in an eight-foot tunnel during August 1975. The purpose of the program was to obtain basic shuttle aerodynamic data through a full range of elevon and aileron deflections, verification of data obtained at other facilities, and effects of Reynolds numbers. The first part of a discussion of test procedures and results in both tabular and graphical form were presented. Tests were performed at Mach numbers from 0.35 to 1.20, and at Reynolds numbers for 3.5 million to 8.2 million per foot. The angle of attack was varied from -1 to +20 degrees at sideslip angles of -2, 0, +2 degrees. Sideslip was varied from -6 to +8 degrees at constant angles of attack from 0 to +20 degrees. Various aileron and ailevon settings were tested for various angles of attack.

Struzynski, N. A.↗
NASA NTRS1974

Analysis of the wind tunnel test of a tilt rotor power force model

Two series of wind tunnel tests were made to determine performance, stability and control, and rotor wake interaction on the airframe, using a one-tenth scale powered force model of a tilt rotor aircraft. Testing covered hover (IGE/OCE), helicopter, conversion, and airplane flight configurations. Forces and moments were recorded for the model from predetermined trim attitudes. Control positions were adjusted to trim flight (one-g lift, pitching moment and drag zero) within the uncorrected test data balance accuracy. Pitch and yaw sweeps were made about the trim attitudes with the control held at the trimmed settings to determine the static stability characteristics. Tail on, tail off, rotors on, and rotors off configurations were testes to determine the rotor wake effects on the empennage. Results are presented and discussed.

Marr, R. L.↗
NASA NTRS1977

Two-dimensional wind tunnel test of an oscillating rotor airfoil, volume 1

A two dimensional wind tunnel test was conducted to obtain the quasisteady and unsteady characteristics of an advanced airfoil designed for helicopter rotor applications. Differential pressures were measured at 17 locations along the chord of the airfoil model. The airfoil motions were sinusoidal forced-pitch oscillations about the quarter chord at amplitudes varying from 2.5 to 10.0 degrees and at frequencies from 23 Hz to 90 Hz. The quasisteady tests were conducted at Mach numbers from 0.2 to 0.9, and the oscillatory tests between M = 0.2 and M = 0.7. At quasisteady conditions a limited number of drag measurements were made with a wake-traversing probe.

Dadone, L. U.↗
NASA NTRS1987

Wind-tunnel test results of airfoil modifications for the EA-6B

Wind-tunnel tests have been conducted (to determine the effects on airfoil performance for several airfoil modifications) for the EA-6B Wing Improvement Program. The modifications consist of contour changes to the leading-edge slat and trailing-edge flap to provide a higher low-speed maximum lift with no high-speed cruise-drag penalty. Airfoil sections from the 28- and 76-percent span stations were selected as baseline shapes with the major testing devoted to the inboard airfoil section (28-percent span station). The airfoil modifications increased the low-speed maximum lift coefficient between 20 and 35 percent over test conditions of 3 to 14 million chord Reynolds number and 0.14 to 0.34 Mach number. At the high-speed test conditions of 0.4 to 0.80 Mach number and 10 million chord Reynolds number, the modified airfoils had either matched or had lower drag coefficients for all normal-force coefficients above 0.2 as compared to the baseline airfoil. At normal-force coefficients less than 0.2, the baseline (original) airfoil had lower drag coefficients than any of the modified airfoils.

Sewall, W. G.↗
NASA NTRS1961

Wind-Tunnel Tests of Seven Static-Pressure Probes at Transonic Speeds

Wind-tunnel tests have been conducted to determine the errors of 3 seven static-pressure probes mounted very close to the nose of a body of revolution simulating a missile forebody. The tests were conducted at Mach numbers from 0.80 to 1.08 and at angles of attack from -1.7 deg to 8.4 deg. The test Reynolds number per foot varied from 3.35 x 10(exp 6) to 4.05 x 10(exp 6). For three 4-vane, gimbaled probes, the static-pressure errors remained constant throughout the test angle-of-attack range for all Mach numbers except 1.02. For two single-vane, self-rotating probes having two orifices at +/-37.5 deg. from the plane of symmetry on the lower surface of the probe body, the static-pressure error varied as much as 1.5 percent of free-stream static pressure through the test angle-of- attack range for all Mach numbers. For two fixed, cone-cylinder probes of short length and large diameter, the static-pressure error varied over the test angle-of-attack range at constant Mach numbers as much as 8 to 10 percent of free-stream static pressure.

Capone, Francis J.↗
NASA NTRS1976

Aerodynamic results of wind tunnel tests on a 0.010-scale model (32-QTS) space shuttle integrated vehicle in the AEDC VKF-40-inch supersonic wind tunnel (IA61)

Plotted and tabulated aerodynamic coefficient data from a wind tunnel test of the integrated space shuttle vehicle are presented. The primary test objective was to determine proximity force and moment data for the orbiter/external tank and solid rocket booster (SRB) with and without separation rockets firing for both single and dual booster runs. Data were obtained at three points (t = 0, 1.25, and 2.0 seconds) on the nominal SRB separation trajectory.

Daileda, J. J.↗
NASA NTRS1993

Aerodynamic control of NASP-type vehicles through Vortex manipulation. Volume 2: Static wind tunnel tests

Forebody Vortex Control (FVC) was explored in this research program for potential application to a NASP-type configuration. Wind tunnel tests were conducted to evaluate a number of jet blowing schemes. The configuration tested has a slender forebody and a 78 deg swept delta wing. Blowing jets were implemented on the leeward side of the forebody with small circular tubes tangential to the surface that could be directed aft, forward, or at angles in between. The effects of blowing are observed primarily in the yawing and rolling moments and are highly dependent on the jet configuration and the angle of attack. Results show that the baseline flow field, without blowing activated, is quite sensitive to the geometry differences of the various protruding jets, as well as being sensitive to the blowing, particularly in the angle of attack range where the forebody vortices are naturally asymmetric. The time lag of the flow field response to the initiation of blowing was also measured. The time response was very short, on the order of the time required for the flow disturbance to travel the distance from the nozzle to the specific airframe location of interest at the free stream velocity. Overall, results indicate that sizable yawing and rolling moments can be induced with modest blowing levels. However, direct application of this technique on a very slender forebody would require thorough wind tunnel testing to optimize the jet location and configuration.

Suarez, Carlos J.↗
NASA NTRSDate not supplied

Spectral Proper Orthogonal Decomposition of uPSP Measurements in Recent NASA Ames Wind Tunnel Test

This paper discusses Spectral Proper Orthogonal Decomposition (SPOD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements in recent NASA Ames wind tunnel test. The uPSP measurements were collected using Innovative Scientific Solutions, Inc. (ISSI) Porous, Fast-Response Pressure-Sensitive Paint (FP-XXX), 40 ISSI four-inch air-cooled Light-Emitting Diodes (LEDs), and 8 Phantom v2512 high-speed cameras at 10,000 frames per second in the Launch Vehicle Demo Test (LVDT) of the Space Launch System (SLS) Block 1B crew vehicle in the 11-by 11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in April 2024. Fig. 1 shows the scale model of the SLS launch vehicle installed in the wind tunnel during the test.

Aeroacoustics↗
NASA NTRS1979

Integration Time Required to Extract Accurate Data from Transonic Wind-Tunnel Tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for static aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency bandwidth used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 s; static pressure tests, 1 s; flutter tests, 30 to 60 s; and random-dynamic tests, 10 s.

Muhlstein, Lado, Jr.↗
NASA NTRS1923

Wind tunnel tests of five strut sections in yaw

In the first series of wind tunnel tests, the drag and cross wing force of all the struts were measured at a wind speed of 30 mph and at angles of yaw from 0 degrees to 20 degrees. To determine the magnitude of the VL effect, each strut was tested at zero yaw and at a series of speeds ranging from 15 to 38 mph. Although designed as fairings for cables, part of these sections gave such high crosswind forces that they seemed to have possibilities as airfoils. Therefore, the lift (identical with the crosswind force) and drag coefficients were recalculated for four sections on the basis of broadside area to make them comparable with wing coefficients. The general conclusion that the best fineness ratio for a strut is a function of the Reynolds number, decreasing steadily as that quality increases, has of course been reached many times, both by theory and experiment. It was confirmed here once more, and the effect of form on sensitiveness to VL is also strikingly shown. It seems probable that this effect of form is largely due to interaction between the nose and tail, and to the influence which the form of the nose exerts over the whole flow around the strut.

PROPELLERS, METAL↗
NASA NTRS1975

Integration time required to extract accurate static and dynamic data from transonic wind-tunnel tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for 'static' aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency content of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency band width used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 sec; static pressure tests, 0.1 sec; flutter tests, 30 to 60 sec; and random-dynamic tests, 10 sec.

Muhlstein, L., Jr.↗
NASA NTRS1991

Development of an intelligent hypertext system for wind tunnel testing

This paper summarizes the results of a system utilizing artificial intelligence technology to improve the productivity of project engineers who conduct wind tunnel tests. The objective was to create an intelligent hypertext system which integrates a hypertext manual and expert system that stores experts' knowledge and experience. The preliminary (Phase I) effort implemented a prototype IHS module encompassing a portion of the manuals and knowledge used for wind tunnel testing. The effort successfully demonstrated the feasibility of the intelligent hypertext system concept. A module for the internal strain gage balance, implemented on both IBM-PC and Macintosh computers, is presented. A description of the Phase II effort is included.

Lo, Ching F.↗
NASA NTRS1973

Some comments on V/STOL wind tunnel testing in the transition flight region

Flow breakdown and flow distortion are discussed as the two limitations to wind tunnel testing of V/STOL models at speeds within or near the transition region. It is shown that a very large wind tunnel would be most useful for research into basic aerodynamic phenomena associated with V/STOL aircraft. The large tunnel will not be able to meet the requirements of all the desired testing of V/STOL models, and smaller existing tunnels will continue to be used. There is need for more work, both experimental and theoretical, to bring about a more correct use of the smaller wind tunnels. The large tunnel would be a most useful tool in this work.

Rae, W. H., Jr.↗
NASA NTRS1975

Acoustical characteristics of the NASA Langley full scale wind tunnel test section

The full-scale wind tunnel at NASA-Langley Research Center was designed for low-speed aerodynamic testing of aircraft. Sound absorbing treatment has been added to the ceiling and walls of the tunnel test section to create a more anechoic condition for taking acoustical measurements during aerodynamic tests. The results of an experimental investigation of the present acoustical characteristics of the tunnel test section are presented. The experimental program included measurements of ambient nosie levels existing during various tunnel operating conditions, investigation of the sound field produced by an omnidirectional source, and determination of sound field decay rates for impulsive noise excitation. A comparison of the current results with previous measurements shows that the added sound treatment has improved the acoustical condition of the tunnel test section. An analysis of the data indicate that sound reflections from the tunnel ground-board platform could create difficulties in the interpretation of actual test results.

Abrahamson, A. L.↗