Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind blades”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Investigation of Rotor Performance and Loads of a UH-60A Individual Blade Control System

Wind tunnel measurements of performance, loads, and vibration of a full-scale UH-60A Black Hawk main rotor with an individual blade control (IBC) system are compared with calculations obtained using the comprehensive helicopter analysis CAMRAD II and a coupled CAMRAD II/OVERFLOW 2 analysis. Measured data show a 5.1% rotor power reduction (8.6% rotor lift to effective-drag ratio increase) using 2/rev IBC actuation with 2.0. amplitude at u = 0.4. At the optimum IBC phase for rotor performance, IBC actuator force (pitch link force) decreased, and neither flap nor chord bending moments changed significantly. CAMRAD II predicts the rotor power variations with IBC phase reasonably well at u = 0.35. However, the correlation degrades at u = 0.4. Coupled CAMRAD II/OVERFLOW 2 shows excellent correlation with the measured rotor power variations with IBC phase at both u = 0.35 and u = 0.4. Maximum reduction of IBC actuator force is better predicted with CAMRAD II, but general trends are better captured with the coupled analysis. The correlation of vibratory hub loads is generally poor by both methods, although the coupled analysis somewhat captures general trends.

Yeo, Hyeonsoo↗
NASA NTRS2011

Investigation of Rotor Performance and Loads of a UH-60A Individual Blade Control System

Wind tunnel measurements of performance, loads, and vibration of a full-scale UH-60A Black Hawk main rotor with an individual blade control (IBC) system are compared with calculations obtained using the comprehensive helicopter analysis CAMRAD II and a coupled CAMRAD II/OVERFLOW 2 analysis. Measured data show a 5.1% rotor power reduction (8.6% rotor lift to effective-drag ratio increase) using 2/rev IBC actuation with 2.0 amplitude at = 0.4. At the optimum IBC phase for rotor performance, IBC actuator force (pitch link force) decreased, and neither flap nor chord bending moments changed significantly. CAMRAD II predicts the rotor power variations with the IBC phase reasonably well at = 0.35. However, the correlation degrades at = 0.4. Coupled CAMRAD II/OVERFLOW 2 shows excellent correlation with the measured rotor power variations with the IBC phase at both = 0.35 and = 0.4. Maximum reduction of IBC actuator force is better predicted with CAMRAD II, but general trends are better captured with the coupled analysis. The correlation of vibratory hub loads is generally poor by both methods, although the coupled analysis somewhat captures general trends.

Yeo, Hyeonsoo↗
NASA NTRS2014

Data Summary Report for the Open Rotor Propulsion Rig Equipped with F31/A31 Rotor Blades

An extensive wind tunnel test campaign was undertaken to quantify the performance and acoustics of a counter-rotating open rotor system. The present document summarizes the portion of this test performed with the so-called "Historical Baseline" rotor blades, designated F31/A31. It includes performance and acoustic data acquired at Mach numbers from take-off to cruise. It also includes the effect of propulsor angle of attack as well as an upstream pylon. This report is accompanied by an electronic data set including relevant acoustic and performance measurements for all of the F31/A31 data.

Acoustics↗
NASA NTRS2014

Data Summary Report for the Open Rotor Propulsion Rig Equipped With F31/A31 Rotor Blades

An extensive wind tunnel test campaign was undertaken to quantify the performance and acoustics of a counter-rotating open rotor system. The present document summarizes the portion of this test performed with the so-called Historical Baseline rotor blades, designated F31A31. It includes performance and acoustic data acquired at Mach numbers from take-off to cruise. It also includes the effect of propulsor angle of attack as well as an upstream pylon. This report is accompanied by an electronic data set including relevant acoustic and performance measurements for all of the F31A31 data.

Open rotor↗
NASA NTRS1973

The effect of aerodynamic parameters on power output of windmills

Aerodynamic results for a study on windpower generation are reported. Windmill power output is presented in terms that are commonly used in rotary wing analysis, namely, power output as a function of drag developed by the windmill. Effect of tip speed ratio, solidity, twist, wind angle, blade setting and airfoil characteristics are given.

Wiesner, W.↗
NASA NTRS1981

Double-multiple streamtube model for Darrieus in turbines

An analytical model is proposed for calculating the rotor performance and aerodynamic blade forces for Darrieus wind turbines with curved blades. The method of analysis uses a multiple-streamtube model, divided into two parts: one modeling the upstream half-cycle of the rotor and the other, the downstream half-cycle. The upwind and downwind components of the induced velocities at each level of the rotor were obtained using the principle of two actuator disks in tandem. Variation of the induced velocities in the two parts of the rotor produces larger forces in the upstream zone and smaller forces in the downstream zone. Comparisons of the overall rotor performance with previous methods and field test data show the important improvement obtained with the present model. The calculations were made using the computer code CARDAA developed at IREQ. The double-multiple streamtube model presented has two major advantages: it requires a much shorter computer time than the three-dimensional vortex model and is more accurate than multiple-streamtube model in predicting the aerodynamic blade loads.

Paraschivoiu, I.↗
NASA NTRS1982

The development and manufacture of wood composite wind turbine rotors

The physical properties, operational experience, and construction methods of the wood/epoxy composite MOD 0A wind turbine blades are considered. Blades of this type have accumulated over 10,000 hours of successful operation at the Kahuku, Hawaii and Block Island, Rhode Island test sites. That body of experience is summarized and related to the structural concepts and design drivers which motivated the original design and choice of interior layout. Actual manufacturing experience and associated low first unit costs for these blades, as well as projections for high production rates, are presented. Application of these construction techniques to a wide range of other blade sizes is also considered.

Zuteck, M. D.↗
NASA NTRS1985

Development of large wind energy power generation system

The background and development of an experimental 100 kW wind-energy generation system are described, and the results of current field tests are presented. The experimental wind turbine is a two-bladed down-wind horizontal axis propeller type with a 29.4 m diameter rotor and a tower 28 m in height. The plant was completed in March, 1983, and has been undergoing trouble-free tests since then. The present program calls for field tests during two years from fiscal 1983 to 1984. The development of technologies relating to the linkage and operation of wind-energy power generation system networks is planned along with the acquisition of basic data for the development of a large-scale wind energy power generation system.

Source record↗
NASA NTRS1990

Improved Radiography Of Wooden Parts

Technique developed to increase radiographic contrasts of inherent latent defects in wood. Involves introduction of radiopaque substance into defect site and subjecting site to penetrating radiation. Radiopaque penetrant used is commercially available fluorocarbon cleaning solvent, trichlorotrifluoroethane. Applicable in inspection of wooden aircraft components, fan and wind-turbine blades, marine parts, insulators, and other wooden components, assemblies, and structures.

Berry, Maggie L.↗
NASA NTRS1989

Thermographic detection of disbonds

The presence of disbonds significantly decreases the integrity of many laminated structures used in aerospace applications. A thermographic technique is presented which is able to detect subsurface delamination. The technique uses one of several heat sources (such as hot water, hot air, IR lamps, etc.) to increase the surface temperature of the structure. The subsequent temperature profiles of the surface are detected with an IR camera. A novel spatial filter developed at NASA-Langley eliminates the effects of uneven heating to give clear images of the subsurface delaminations. Defects are detectable in samples as diverse as solid rocket motor samples and laminated wood for wind tunnel blades. Numerical simulations are presented for comparison with experiment results.

Winfree, William P.↗
NASA NTRSDate not supplied

STITCHED COMPOSITES WITH THREE-DIMENSIONAL STITCH PATHS

Stitched composites have been shown to exhibit damage tolerance and to reduce weight compared to traditional layered composites through unitization of the structure by elimination of fasteners. Stitching capabilities have been incorporated into the Integrated Structural Assembly of Advanced Composites (ISAAC) system at NASA Langley Research Center with the introduction of two stitching heads. Stitching path control was initially implemented as straight lines in space, as was done for previous stitching development. However, more complex stitched structures such as a wind tunnel blade or around cutouts within a fuselage or wing skin, require that the stitching paths be implemented as three-dimensional (3D) stitching paths in space. Unfortunately, control programming output by an existing preprocessor program cannot stitch these curved paths due to problems that arise in stitch formation and the introduction of side forces on the needles using the conventional programming approach whereby the head is simultaneously controlled through translations and rotations. This lack of capability is most significant for the single-sided stitching head, where two needles are in the preform at the same time for the majority of the stitching process. A means to program 3D stitching paths in space was developed whereby the translation and rotation of each stitch were decoupled, thereby eliminating the problems associated with current control programming approach. Using this newly developed stitching path definition and control programming, complex stitching paths have successfully been stitched at the ISAAC facility. The ability to stitch general 3D stitching paths in space enables the use of stitching on more complex parts.

carbon-epoxy↗
NASA NTRSDate not supplied

Stitched Composites with Three-Dimensional Stitch Paths

Stitched composites have been shown to exhibit damage tolerance and to reduce weight compared to traditional layered composites through unitization of the structure by elimination of fasteners. Stitching capabilities have been incorporated into the Integrated Structural Assembly of Advanced Composites (ISAAC) system at NASA Langley Research Center with the introduction of two stitching heads. Stitching path control was initially implemented as straight lines in space, as was done for previous stitching development. However, more complex stitched structures such as a wind tunnel blade or around cutouts within a fuselage or wing skin, require that the stitching paths be implemented as three-dimensional (3D) stitching paths in space. Unfortunately, control programming output by an existing preprocessor program cannot stitch these curved paths due to problems that arise in stitch formation and the introduction of side forces on the needles using the conventional programming approach whereby the head is simultaneously controlled through translations and rotations. This lack of capability is most significant for the single-sided stitching head, where two needles are in the preform at the same time for the majority of the stitching process. A means to program 3D stitching paths in space was developed whereby the translation and rotation of each stitch were decoupled, thereby eliminating the problems associated with current control programming approach. Using this newly developed stitching path definition and control programming, complex stitching paths have successfully been stitched at the ISAAC facility. The ability to stitch general 3D stitching paths in space enables the use of stitching on more complex parts.

carbon-epoxy↗
NASA NTRS1982

Fiberglass composite blades for the 2 MW Mod-1 wind turbine generator

In mid-1979, NASA contracted with Kaman Aerospace Corporation for the design, manufacture, and ground testing of two 100 foot composite rotor blades intended for operation on the Mod-1 wind turbine. The Mod-1 blades have been completed and are currently stored at the Kaman facility. The design, tooling, fabrication, and testing phases which have been carried out to date, as well as testing still planned are described. Discussed are differences from the 150 foot blade which were introduced for cost and manufacturing improvement purposes. Also included is a description of the lightning protection system installed in the blades, and its development program. Actual costs and manhours expended for Blade No. 2 are provided as a base, along with a projection of costs for the blade in production. Finally, cost drivers are identified relative to future designs.

Batesole, W. R.↗
NASA NTRS1979

Preliminary analysis of performance and loads data from the 2-megawatt mod-1 wind turbine generator

Preliminary test data on output power versus wind speed, rotor blade loads, system dynamic behavior, and start-stop characteristics on the Mod-1 wind turbine generator are presented. These data were analyzed statistically and are compared with design predictions of system performance and loads. To date, the Mod-1 wind turbine generator has produced up to 1.5 MW of power, with a measured power versus wind speed curve which agrees closely with design. Blade loads were measured at wind speeds up to 14 m/s and also during rapid shutdowns. Peak transient loads during the most severe shutdowns are less than the design limit loads. On the inboard blade sections, fatigue loads are approximately equal to the design cyclic loads. On the outboard blade sections, however, measured cyclic loads are significantly larger than design values, but they do not appear to exceed fatigue allowable loads as yet.

Spera, D. A.↗
NASA NTRS1993

Full-scale wind tunnel investigation of a helicopter individual blade control system

This paper discusses the preparations and plans to test an individual rotor blade pitch control system in the 40- by 80- Foot Wind Tunnel at the NASA Ames Research Center. The test will be performed on a full-scale BO-105 rotor system using a control system made by Henschel Flugzeug-Werke, GmbH, Germany. The Individual Blade Control (IBC) actuators have been designed to replace the pitchlinks of the rotor system. The paper presents a brief historical perspective on the development of the individual blade control system and then describes the present IBC actuators and the wind tunnel test hardware. A discussion of the intended test matrix, expected potential benefits of IBC, and simulation results are included.

Jacklin, Stephen A.↗
NASA NTRS1998

Wind-Tunnel Evaluation of the Effect of Blade Nonstructural Mass Distribution on Helicopter Fixed-System Loads

This report provides data obtained during a wind-tunnel test conducted to investigate parametrically the effect of blade nonstructural mass on helicopter fixed-system vibratory loads. The data were obtained with aeroelastically scaled model rotor blades that allowed for the addition of concentrated nonstructural masses at multiple locations along the blade radius. Testing was conducted for advance ratios ranging from 0.10 to 0.35 for 10 blade-mass configurations. Three thrust levels were obtained at representative full-scale shaft angles for each blade-mass configuration. This report provides the fixed-system forces and moments measured during testing. The comprehensive database obtained is well-suited for use in correlation and development of advanced rotorcraft analyses.

ARES-1(AEROELASTIC ROTOR EXPERIMENTAL SYSTEM 1)↗
NASA NTRS1976

Tower and rotor blade vibration test results for a 100-kilowatt wind turbine

The predominant natural frequencies and mode shapes for the tower and the rotor blades of the ERDA-NASA 100-kW wind turbine were determined. The tests on the tower and the blades were conducted both before and after the rotor blades and the rotating machinery were installed on top of the tower. The tower and each blade were instrumented with an accelerometer and impacted by an instrumented mass. The tower and blade structure was analyzed by means of NASTRAN, and computed values agree with the test data.

Linscott, B. S.↗