Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “visibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Visible emission spectra of thermographic phosphors under x-ray excitation

Thermographic phosphors have been employed for temperature sensing in challenging environments, such as on surfaces or within solid samples exposed to dynamic heating, because of the high temporal and spatial resolution that can be achieved using this approach. Typically, UV light sources are employed to induce temperature-sensitive spectral responses from the phosphors. However, it would be beneficial to explore x-rays as an alternate excitation source to facilitate simultaneous x-ray imaging of material deformation and temperature of heated samples and to reduce UV absorption within solid samples being investigated. Here, the phosphors BaMgAl 10 O 17 :Eu (BAM), Y 2 SiO 5 :Ce, YAG:Dy, La 2 O 2 S:Eu, ZnGa 2 O 4 :Mn, Mg 3 F 2 GeO 4 :Mn, Gd 2 O 2 S:Tb, and ZnO were excited using incident synchrotron x-ray radiation. These materials were chosen to include conventional thermographic phosphors as well as x-ray scintillators (with crossover between these two categories). X-ray-induced thermographic behavior was explored through the measurement of visible spectral response with varying temperature. The incident x-rays were observed to excite the same electronic energy level transitions in these phosphors as UV excitation. Similar shifts in the spectral response of BAM, Y 2 SiO 5 :Ce, YAG:Dy, La 2 O 2 S:Eu, ZnGa 2 O 4 :Mn, Mg 3 F 2 GeO 4 :Mn, and Gd 2 O 2 S:Tb were observed when compared to their response to UV excitation found in literature. Some phosphors were observed to thermally quench in the temperature ranges tested here, while the response from others did not rise above background noise levels. This may be attributed to the increased probability of non-radiative energy release from these phosphors due to the high energy of the incident x-rays. These results indicate that x-rays can serve as a viable excitation source for phosphor thermometry.

42 ENGINEERING↗
DOE OSTI2021

Metallic and porous Ti nanorod arrays for visible-IR light absorption and dendrite-free stable lithium-metal batteries

It is still a challenging task to prepare highly porous nanorod arrays of metals formed on substrates for optical and energy storage applications. Herein, we demonstrate the design and synthesis of black color, metallic and highly porous Ti nanorod arrays as novel current collectors for dendrite-free and highly stable Li-metal anodes. The high porosity of metallic nanorod arrays provides numerous heterogeneous nucleation sites and huge contact area and large space for the accommodation of Li metal. The conductive metallic Ti nanorod arrays enhance electrode integration. Effectively, it eliminates formation Li dendrites and demonstrates superior cycling stability over 300 cycles. Additionally, the unique porous structures of the nanorod arrays can decrease the amplitude of forced vibration in narrow space leading to light absorption. Interestingly, the metal is black instead of metallic color. The black metallic nanorod arrays can absorb more than 96% of both visible and infra-red lights. Furthermore, this black color metallic porous nanorod arrays may find additional applications in aerospace, energy, biomedical, defence, and chemical industries.

25 ENERGY STORAGE↗
DOE OSTI2021

Visible spectroscopy of highly charged tungsten ions with the JET charge exchange diagnostic

Since the installation of the ITER-like wall on the JET tokamak, visible emission from a broad range of tungsten charge states has complicated plasma ion temperature and toroidal rotation measurements. A plethora of charge exchange transitions, from ions up to W 56+ , and 21 suspected magnetic dipole transitions have been observed. In particular W 39+ and W 46+ charge exchange emission contaminates the long-established carbon measurement at 529 nm. Fortunately the wavelength and relative intensity of the tungsten charge exchange lines is predictable and their influence can be mitigated when they are included in the spectral fit. Neon based charge exchange measurements at 525 nm are now preferred on JET since the ITER-like wall, however in this case an unidentified tungsten magnetic dipole transition contaminates the spectrum when the electron temperature is low.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Dependence of polytetrafluoroethylene reflectance on thickness at visible and ultraviolet wavelengths in air

Polytetrafluoroethylene (PTFE) is an excellent diffuse reflector widely used in light collection systems for particle physics experiments. However, the reflectance of PTFE is a function of its thickness. Here, in this work, we investigate this dependence in air for light of wavelengths 260 nm and 450 nm using two complementary methods. We find that PTFE reflectance for thicknesses from 5 mm to 10 mm ranges from 92.5% to 94.5% at 450 nm, and from 90.0% to 92.0% at 260 nm. We also see that the reflectance of PTFE of a given thickness can vary by as much as 2.7% within the same piece of material. Finally, we show that placing a specular reflector behind the PTFE can recover the loss of reflectance in the visible without introducing a specular component in the reflectance.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Comparison of continuum-continuum and Coulomb-laser-coupling delays from visible to midinfrared wavelengths

We compare the various proposed formulas for CLC and CC delays using analytical and numerical methods across a range of wavelengths spanning visible to midinfrared. We show that one of the CC definitions is nearly equal to the CLC delay over a range of photoelectron energies and wavelengths. We furthermore obtain alternate expressions for the CC delays. These expressions are simpler to use and show close correspondence to the CLC delays. Based on this correspondence, we suggest a correction to the CLC delay for low-energy electrons, where the currently used approximation breaks down. Our work provides guidance for when it is valid to treat CC and CLC delays as being equivalent.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Second-order nonlinear optical and linear ultraviolet-visible absorption properties of the type-II multiferroic candidates RbFe( A O 4 ) 2 ( A = Mo, Se, S)

Motivated by the search for type-II multiferroics, in this work, we present a comprehensive optical study of a complex oxide family of type-II multiferroic candidates: RbFe(MoO 4 ) 2 , RbFe(SeO 4 ) 2 , and RbFe(SO 4 ) 2 .We employ rotationalanisotropy second harmonic generation spectroscopy (RA SHG), a technique sensitive to point symmetries, to address discrepancies in literature-assigned point/space groups and to identify the correct crystal structures. At room temperature we find that our RA SHG patterns rotate away from the crystal axes in RbFe(AO 4 ) 2 ( A = Se, S), which identifies the lack of mirror symmetry and in-plane two-fold rotational symmetry. Also, the SHG efficiency of RbFe(SeO 4 ) 2 is two orders of magnitude stronger than RbFe(AO 4 )2 ( A = Mo, S), which suggests broken inversion symmetry. Additionally, we present temperature-dependent linear optical characterizations near the band edge of this family of materials using ultraviolet-visible absorption spectroscopy. Included is experimental evidence of the band gap energy and band gap transition type for this family. Subband gap absorption is also presented, which reveals prominent optical transitions, some with an unusual central energy temperature dependence. Furthermore, we find that by substituting the A site in RbFe(AO 4 ) 2 ( A = Mo, Se, S), the aforementioned transitions are spectrally tunable. Finally, we discuss the potential origin and impact of these tunable transitions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Photonics Breakthroughs 2024: Narrow-Linewidth Lasers in the Visible and Near-Infrared

Narrow-linewidth lasers enable a variety of high-precision applications, such as sensing, optical clocks, and microwave frequency generation. Advances in photonic integration in the last decade led to the development of ultra-low-noise integrated semiconductor lasers, mostly in the telecom wavelength range. In recent years, the demand for high-performance lasers at shorter wavelengths skyrocketed, driven by applications in sensing and atom trapping. Low-noise lasers are of particular importance in this spectral range, as they are essential for optical clocks. Here, we will review recent progress in narrow-linewidth lasers at shorter wavelengths, present results on a hybrid-integrated low-noise laser at 780 nm and discuss the perspectives and challenges of high-performance semiconductor lasers in the visible and near-infrared.

Prokoshin, Artem [King Abdullah University of Scie↗
DOE OSTI2023

Development of a Low-Cost, Sensitivity-Optimized Fluorescence Sensor for Visible Spectrum Analysis

This paper presents an economically viable, sensitivity-optimized fluorescence sensor for detecting low concentrations of fluorophores in the visible spectrum range. The sensor employs a deep ultraviolet (DUV) 275-nm LED and a dichroic mirror to establish a co-axial optical path for excitation and emission. Instead of utilizing a general-purposed spectrometer optimized for high spectral resolution, the sensor strikes a balance between resolution and sensitivity by using an appropriate aperture size and optimized optical design tailored for the spectral characteristics of fluorophores. Here, the manuscript demonstrates measurements of ppb-level rare earth element (REE) samples containing terbium (Tb), europium (Eu), dysprosium (Dy), and samarium (Sm) in aqueous solutions. Through balanced design that optimizes collection of fluorescence emission without losing spectral information, this work shows the feasibility of developing a low-cost, compact, and highly sensitive fluorescence sensors with improved detection sensitivity when compared to bench-top commercial spectrofluorometers at far higher costs.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

A Hierarchical Control Architecture: Utilization of Behind-the-Meter Appliances with Increased Visibility and Controllability

Optimal operations of distribution systems to enhance reliability and resiliency can be achieved if information with higher fidelity can be accessed from grid premise devices. This paper discusses a hierarchical control architecture that can introduce higher visibility and controllability by utilizing the estimated injection and absorption of different behind-the-meter controllable loads, and DERs, including EVs, within a premise. The acquired information is used to make control decisions for scheduling the premise appliances to reduce energy consumptions. The premise controller can also optimize the consumptions on a day-to-day basis in addition to taking input signals from the utility operators to support grid-service events (e.g., peak shaving). The entire control architecture is designed in a modular and scalable fashion that provides benefits to the utility from the reuse of existing infrastructure while creating opportunities for various grid services to be enabled by the operation of premise controllers.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Modeling Buried Object Brightness and Visibility for Ground Penetrating Radar

Comparing the observed brightness of various buried objects is a straightforward way to characterize the performance of a ground penetrating radar (GPR) system. However, a limitation arises. A simple comparison of buried object brightness values does not disentangle the effects of the GPR system itself from the system's operating environment and the objects being observed. Therefore, with brightness values exhibiting an unknown synthesis of systemic, environmental, and object factors, GPR system analysis becomes a convoluted affair. In this work, we use an experimentally collected dataset of over 25,000 object observations from five different multistatic radar arrays to develop models of buried object brightness and control for these various effects. Additionally, our modeling efforts provide a means for quantifying the relative brightness of GPR systems, the objects they detect, and the physical properties of those objects that influence observed brightness. To evaluate the models' performance on new object observations, we repeatedly simulate fitting them to half the dataset and predicting the observed brightness values of the unseen half. In addition, we introduce a method for estimating the probability that individual observations constitute a visible object, which aids in failure analysis, performance characterization, and dataset cleaning.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Melt-grown semi-insulating Mn:β-Ga 2 O 3 single crystals exhibiting unique visible absorptions and luminescence

In this study, several acceptor dopants have been explored in β-Ga 2 O 3 to produce semi-insulating substrates and epitaxial films. Fe and Mg make up the majority of research thus far; however, other transition metals provide potential alternatives for optimized performance. β-Ga 2 O 3 bulk single crystals were grown by the Czochralski and vertical gradient freeze methods with a nominal dopant concentration of 0.25 at. % Mn. Ultraviolet-visible-near infrared spectroscopy and photoluminescence revealed polarization- and orientation-dependent optical absorptions (pleochroism) coupled with an orange luminescence. All samples were electrically insulating, on the order of 10 9 –10 11 ohm cm at room temperature, indicative of acceptor doping. Actual dopant concentrations of the intentionally doped transition metal and background impurities were determined via glow discharge mass spectrometry, indicating the macroscale segregation behavior. High-temperature resistivity measurements indicated an experimental acceptor level of 1.7 ± 0.2 eV. Hydrogenation of samples resulted in an increase in the orange luminescence and O–H stretching modes observable in the infrared spectrum. Density functional theory calculations were performed to determine the likely site-occupancy and acceptor level of Mn in the bandgap.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Large-area low-noise flexible organic photodiodes for detecting faint visible light

Silicon photodiodes are the foundation of light-detection technology; yet their rigid structure and limited area scaling at low cost hamper their use in several emerging applications. A detailed methodology for the characterization of organic photodiodes based on polymeric bulk heterojunctions reveals the influence that charge-collecting electrodes have on the electronic noise at low frequency. The performance of optimized organic photodiodes is found to rival that of low-noise silicon photodiodes in all metrics within the visible spectral range, except response time, which is still video-rate compatible. Solution-processed organic photodiodes offer several design opportunities exemplified in a biometric monitoring application that uses ring-shaped, large-area, flexible, organic photodiodes with silicon-level performance.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

In situ Visible Light and Thermal Imaging Data from a Laser Powder Bed Fusion Additive Manufacturing Process Co-Registered to X-ray Computed Tomography and Fatigue Data

This dataset is comprised of in situ sensing data collected during a laser-based powder bed fusion additive manufacturing process, as well as rasterized scan path information, post-build X-ray computed tomography (XCT), and fatigue test results. A total of 64 cylinders, approximately 15 mm in diameter and 102 mm tall, were printed out of stainless steel 316H on a Colibrium Additive Concept Laser M2 Series 5 machine. Parameters known to produce dense material were used to construct 56 of these cylinders, while the remaining 8 cylinders were printed with relatively high energy density parameters prone to producing keyhole pores. In addition, two spatter generation blocks were constructed upstream of the 64 cylinders such that ejecta produced during the melting of the spatter generators were stochastically seeded onto the 64 cylinders. Based on previous experiments, these spatter particles were theorized to produce stochastic lack-of-fusion pores. During the construction of the build, high-resolution images of reflected light in the visible spectrum were captured both before and after recoating for each print layer. Additionally, temporally integrated thermal imaging in the near infrared spectrum produced integrated sum and max images on a layerwise basis. The multimodal in situ data has been co-registered to the build plate coordinate system, allowing for identification of process anomalies (e.g., spatter particles) apparent in the two sensors. Following construction of the build, the cylinders were subjected to XCT to identify internal flaws, and the resulting data have also been registered to the build plate coordinate system. Finally, 60 of the 64 cylinders were machined into fatigue coupons conforming to ASTM E466 and subsequently subjected to either high- or -low-cycle fatigue testing. The results of the fatigue tests have also been included in the dataset, and the XCT data corresponded to the approximate location of the gauge sections of the machine fatigue specimen geometry.

42 ENGINEERING↗
DOE OSTI2022

Visible (400- to 700-nm) chirped-grating-coupled waveguide spectrometer

An integrable on-chip spectrometer, based on a transversely-chirped-grating waveguide-coupler for the 400- to 700-nm visible spectral range is demonstrated. For a fixed angle of incidence, the coupling wavelength is dependent on the local grating period and the waveguide structure. The transversely-chirped-input grating is fabricated on a SiO 2 -Si 3 N 4 -SiO 2 waveguide atop a Si substrate by interferometric lithography in two sections on a single silicon substrate. A uniform period grating, separated from the input coupler by a propagation region, is provided for out-coupling to a 2048 element CMOS detector array. The incident light with wavelength spanning 400- to 700-nm is coupled into waveguide at 33.5° through the chirped grating coupler. A resolution of ∼ 1.2 nm is demonstrated without any signal processing reconstruction.

Wang, Xuemei↗
DOE OSTI2025

Telecom-to-visible quantum frequency converter on a silicon nitride chip

Quantum frequency conversion serves a key role in the realization of hybrid quantum networks by interfacing between wavelength-incompatible platforms. Here we present what is believed to be the first quantum frequency converter connecting visible and telecom domains on a silicon nitride (SiN) chip, using Bragg-scattering four-wave mixing to upconvert heralded single photons from 1260 to 698 nm, which covers a 192 THz span. We examine the noise sources in SiN and devise approaches to suppress noise photons at the source and target frequencies to enable measurements at the single-photon level. We demonstrate an on-chip conversion efficiency of 5% in photon flux and describe design modifications that can be implemented to significantly improve it. Our results pave the way for the implementation of complementary metal-oxide-semiconductor (CMOS)-compatible devices in quantum networks.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Drone flight visible images, digital elevation maps, and geotiffs, Council, Seward Peninsula, Alaska, USA, July 2017

Remote sensing data collected from Lawrence Berkeley National Laboratory’s (LBNL) unmanned aerial system (UAS) quadcopter platform – Inspire-1 – operated by the Ameriflux Management Project (ameriflux.lbl.gov) Technical Team. The Insprire-1 is a visible imagery UAS platform that simultaneously measures very high spatial resolution optical red/green/blue (RGB) at regular intervals along each flight path. This package includes data from four flight paths over the NGEE Arctic Council Road Site near mile marker 71 in the Seward Peninsula, Alaska in July 2017. Derived image products for each flight include ortho-mosaiced RGB, an RGB-based digital surface model (DSM) using the structure from motion (SfM) technique, and a digital terrain model (DTM). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included. Unprocessed and processed data products are included in this package (processing levels 0-2). This metadata document contains flight campaign, instrument and file metadata, along with a description of data processing levels, data products and file naming scheme.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Drone flight visible images, digital elevation maps, and geotiffs, Teller, Seward Peninsula, Alaska, USA, July 2017

Remote sensing data collected from Lawrence Berkeley National Laboratory’s (LBNL) unmanned aerial system (UAS) quadcopter platform – Inspire-1 – operated by the Ameriflux Management Project (ameriflux.lbl.gov) Technical Team. The Insprire-1 is a visible imagery UAS platform that simultaneously measures very high spatial resolution optical red/green/blue (RGB) at regular intervals along the flight path. This package includes data from a flight path over the NGEE Arctic Teller Site, west of mile marker 27 Bob Blodgett Highway in the Seward Peninsula, Alaska in July 2017. Derived image products include ortho-mosaiced RGB, an RGB-based digital surface model (DSM) using the structure from motion (SfM) technique, and a digital terrain model (DTM). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included. Unprocessed and processed data products are included in this package (processing levels 0-2). This metadata document contains flight campaign, instrument and file metadata, along with a description of data processing levels, data products and file naming scheme.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Drone flight visible images, digital elevation maps, and geotiffs, Kougarok, Seward Peninsula, Alaska, USA, July 2017

Remote sensing data collected from Lawrence Berkeley National Laboratory’s (LBNL) unmanned aerial system (UAS) quadcopter platform – Inspire-1 – operated by the Ameriflux Management Project (ameriflux.lbl.gov) Technical Team. The Insprire-1 is a visible imagery UAS platform that simultaneously measures very high spatial resolution optical red/green/blue (RGB) at regular intervals along each flight path. This package includes data from four flight paths over the NGEE Arctic Kougarok Site, west of mile marker 64 on Kuzitrin Road in the Seward Peninsula, Alaska in July 2017. Derived image products include ortho-mosaiced RGB, an RGB-based digital surface model (DSM) using the structure from motion (SfM) technique, and a digital terrain model (DTM). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included. Unprocessed and processed data products are included in this package (processing levels 0-2). This metadata document contains flight campaign, instrument and file metadata, along with a description of data processing levels, data products and file naming scheme.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗