Results for “vertical orientation” — Page 8

NASA NTRS2015

Thermal Protection System Application to Composite Cryotank Technology Demonstrator

The EM41 Thermal Protection System (TPS) team contributed to the success of the Composite Cryotank Technology Demonstrator (CCTD) manufacturing by developing and implementing a low-cost solution to apply cryoinsulation foam on the exterior surface of the tank in the NASA Marshall Space Flight Center (MSFC) TPS Development Facility, Bldg. 4765. The TPS team used techniques developed for the smallscale composite cryotank to apply Stepanfoam S-180 polyurethane foam to the 5.5-meter CCTD using a manual spray process. Manual spray foam technicians utilized lifts and scaffolding to access the barrel and dome sections of the large-scale tank in the horizontal orientation. During manufacturing, the tank was then oriented vertically, allowing access to the final barrel section for manual spray foam application. The CCTD was the largest application of manual spray foam performed to date with the S-180 polyurethane foam and required the TPS team to employ best practices for process controls on the development article.

Protz, Alison↗

NASA NTRS2017

Stereo Photogrammetry Measurements of the Position and Attitude of a Nozzle-Plume/Shock-Wave Interaction Model in the NASA Ames 9- by 7-Ft Supersonic Wind Tunnel

Stereo photogrammetry was used to measure the position and attitude of a slender body of revolution during nozzle-plume/shock-wave interaction tests in the NASA Ames 9- by 7-Ft Supersonic Wind Tunnel. The model support system was designed to allow the model to be placed at many locations in the test section relative to a pressure rail on one sidewall. It included a streamwise traverse as well as a thin blade that offset the model axis from the sting axis. With these features the support system was more flexible than usual resulting in higher-than-usual uncertainty in the position and attitude of the model. Also contributing to this uncertainty were the absence of a balance, so corrections for sting deflections could not be applied, and the wings-vertical orientation of the model, which precluded using a gravity-based accelerometer to measure pitch angle. Therefore, stereo photogrammetry was chosen to provide independent measures of the model position and orientation. This paper describes the photogrammetry system and presents selected results from the test.

supersonic↗

NASA NTRS2019

NASA Centennial Challenge: 3D Printed Habitat, Phase 3 Final Results

NASA's Centennial Challenges program uses prize competitions with the goal of accelerating innovation in the aerospace industry. Competitions in the Centennial Challenges portfolio have previously focused on advancements in space robotics, regolith excavation, bio-printing, astronaut suit design, small satellites, and solar-powered vehicles. NASA's Three Dimensional (3D) Printed Habitat Centennial Challenge represents a partnership between NASA and the non-profit partner: Bradley University, with co-sponsors Caterpillar, Bechtel, Brick and Mortar Ventures, the American Concrete Institute, and the United States Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC) to spur development in automated additive construction technologies. The challenge asks teams to design and construct a scaled and simulated Martian habitat using indigenous materials and large scale 3D automated printing systems. Phase 1 of the competition, held in 2015, was an architectural design competition for habitat concepts that could be 3D printed. Phase 2, completed in 2017, asked teams to develop feedstocks from indigenous materials and hydrocarbon polymer recyclables, and demonstrate automated printing systems to manufacture these feedstocks into test specimens to assess mechanical strength. This paper will discuss the Phase 3 competition, focusing on technology outcomes that can potentially be infused into both terrestrial and planetary construction applications. The Phase 3 competition was divided into two sub-competitions: 1) virtual construction, where teams created a high fidelity building information model (BIM) of their 3D-printed habitat design and 2) the construction competition, which required teams to 3D print a structural foundation and subject materials samples to freeze/thaw testing and impact testing (level 1), produce a habitat element and complete a hydrostatic test (level 2), and additively manufacture a 1:3 scale habitat onsite in a head to head competition at Caterpillar, inc.'s Edwards Demonstration & Learning Center near Peoria, Illinois over the course of three days (level 3). While the Phase 2 competition focused primarily on the development of novel feedstocks and robotic printing systems, Phase 3 emphasized the scale-up of these systems and autonomous operation (demonstrating the capability to operate systems on precursor missions prior to the arrival of crew, or terrestrially in field operation settings where human tending of a manufacturing system may be limited). The Phase 3 virtual construction levels yielded a number of novel habitat designs, including both modular habitats and vertically-oriented habitat concepts. The Phase 3 construction competition also challenged teams to autonomously place penetrations and interfacing elements in additively manufactured structures. The paper will emphasize potential applications for the new materials and technologies developed under the umbrella of the competition within NASA's portfolio and in Earth-based applications such as disaster response and infrastructure improvement.

Construction↗

NASA NTRS2019

Nasa Centennial Challenge: Three Dimensional (3d) Printed Habitat, Phase 3

NASA's Centennial Challenges program uses prize competitions with the goal of accelerating innovation in the aerospace industry. Competitions in the Centennial Challenges portfolio have previously focused on advancements in space robotics, regolith excavation, bio-printing, astronaut suit design, small satellites, and solar-powered vehicles. NASA's Three Dimensional (3D) Printed Habitat Centennial Challenge represents a partnership between NASA and the non-profit partner: Bradley University, with co-sponsors Caterpillar, Bechtel, Brick and Mortar Ventures, the American Concrete Institute, and the United States Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC) to spur development in automated additive construction technologies. The challenge asks teams to design and construct a scaled and simulated Martian habitat using indigenous materials and large scale 3D automated printing systems. Phase 1 of the competition, held in 2015, was an architectural design competition for habitat concepts that could be 3D printed. Phase 2, completed in 2017, asked teams to develop feedstocks from indigenous materials and hydrocarbon polymer recyclables, and demonstrate automated printing systems to manufacture these feedstocks into test specimens to assess mechanical strength. This paper will discuss the Phase 3 competition, focusing on technology outcomes that can potentially be infused into both terrestrial and planetary construction applications. The Phase 3 competition was divided into two sub-competitions: 1) virtual construction, where teams created a high fidelity building information model (BIM) of their 3D-printed habitat design and 2) the construction competition, which required teams to 3D print a structural foundation and subject materials samples to freeze/thaw testing and impact testing (level 1), produce a habitat element and complete a hydrostatic test (level 2), and additively manufacture a 1:3 scale habitat onsite in a head to head competition at Caterpillar, inc.'s Edwards Demonstration & Learning Center near Peoria, Illinois over the course of three days (level 3). While the Phase 2 competition focused primarily on the development of novel feedstocks and robotic printing systems, Phase 3 emphasized the scale-up of these systems and autonomous operation (demonstrating the capability to operate systems on precursor missions prior to the arrival of crew, or terrestrially in field operation settings where human tending of a manufacturing system may be limited). The Phase 3 virtual construction levels yielded a number of novel habitat designs, including both modular habitats and vertically-oriented habitat concepts. The Phase 3 construction competition also challenged teams to autonomously place penetrations and interfacing elements in additively manufactured structures. The paper will emphasize potential applications for the new materials and technologies developed under the umbrella of the competition within NASA's portfolio and in Earth-based applications such as disaster response and infrastructure improvement.

Centennial challenge↗

NASA NTRSDate not supplied

Replication of Segments of STS-94 as a Lunar Surface Mission

The Artemis program established the goal to land the first woman and first person of color on the Moon, but that is only the beginning of the program. Artemis plans to move towards a sustainable phase, with four crew living on the lunar surface for roughly 30-day annual missions, operating from a Pressurized Rover (PR) and a Surface Habitat (SH). The crew will split up – two living and operating from the PR and the others in the SH, perhaps swapping places halfway through the surface mission. There is a significant degree of maturity surrounding PR operations due to the NASA Desert Research and Technology Studies field tests from 2007-2011. However, there is a degree of uncertainty surrounding activity in the SH, with anecdotal speculation among some Artemis lunar surface engineers that the SH crew might not be fully utilized. Contrary to this belief, there is evidence in US human spaceflight history that the SH crew may instead be extremely busy. In particular, portions of the STS-94 Microgravity Science Lab mission demonstrate a science-based use case for crew activity in the SH. Fifteen Spacelab missions (not including STS-83, which was terminated early due to a fuel cell problem and reflown as STS-94) and eight Spacehab missions used the previously mentioned modules as science labs to expand the science capability of shuttle orbital missions, most flown prior to the assembly of the International Space Station. STS-94 is selected as an example of these flights. STS-94 was a 15.7-day mission with a 7-person crew. The crew operated in split 12-hour shifts, enabling 24-hour science operations. STS-94 used the space shuttle Columbia with the Spacelab module and Extended Duration Orbiter pallet in the cargo bay. The STS-94 physical science investigations were intended to explore various physical aspects of microgravity. These same investigations can be conducted on the Moon to explore 1/6 gravity. The Spacelab module was outfitted with several key facilities to enable this research: Large Isothermal Furnace, Combustion Module-1, Droplet Combustion Experiment, EXPRESS Rack, TEMPUS, Gravity Measurement Devices, and Middeck Glovebox. The current reference concept for the SH is a hybrid inflatable in a vertical orientation. Fairly typical of hybrid inflatables, the SH has an aluminum core pressurized section and a larger inflatable volume, in this case attaching to the top of the core. Two crew will live in the SH at a time, though four can briefly occupy the habitat, such as for contingency or handover activities. This paper will discuss use of the STS-94 physical science equipment in the SH and options for the architectural layout of a resulting physics laboratory. It will also discuss how this laboratory may accompany other science facilities such as biology, human research, and geology. The person hours used by the STS-94 crew to conduct physical science research will be estimated and then mapped to a two-person SH crew, making it possible to determine how many days are required in the SH to complete the lunar gravity physical science investigations at varying levels of crew availability.

STS-94↗

NASA NTRSDate not supplied

A Comparison of Two Non-Contact Strain Measurement Techniques with Applications to Scientific Balloons

Strain measurements of scientific balloon films are necessary for evaluating the film’s material properties, validating material models, and structural evaluations of scale model balloons. This paper presents a comparison of the strain measurement techniques used by the Balloon Program Office’s Balloon Research and Development Lab at NASA Wallops Flight Facility. Two non-contact strain measurement techniques are presented for comparison, along with an assessment of measurement accuracy for both methods. The case study of a vertically oriented cylindrical balloon is presented to illustrate both systems’ performance and draw nominal conclusions of strain as a function of pressure and axial load.

Non-Contact↗

NASA NTRSDate not supplied

A Comparison of Two Non-Contact Strain Measurement Techniques with Applications to Scientific Balloons

Strain measurements of scientific balloon films are necessary for evaluating the film’s material properties, validating material models, and structural evaluations of scale model balloons. This paper presents a comparison of the strain measurement techniques used by the Balloon Program Office’s Balloon Research and Development Lab at NASA Wallops Flight Facility. Two non-contact strain measurement techniques are presented for comparison, along with an assessment of measurement accuracy for both methods. The case study of a vertically oriented cylindrical balloon is presented to illustrate both systems’ performance and draw nominal conclusions of strain as a function of pressure and axial load.

Non-Contact↗

NASA NTRSDate not supplied

Habitable Working and Living Spaces in the Deep Space Science Vessel

The Deep Space Science Vessel (DSSV) is a conceptual design of a very large spacecraft intended as a mobile microgravity science platform. It represents an effort to conceptualize the systems and internal architectures needed to support a forty-eight-person crew for multi-year missions throughout the inner solar system and potentially beyond. The general arrangement of the DSSV is a modular spacecraft. Considering only the pressurized, habitable elements, the DSSV includes two large pressurized modules (Hab and Lab) docked together along with eight smaller node modules completing the habitable configuration. The Hab and Lab modules are docked side by side, with the longitudinal axes parallel to each other and a single docking port connecting them. A node module is docked to each dome on the Hab and Lab modules, such that the two small node modules on each end of the large Hab and Lab domes are docked both to each other and to the Hab and Lab. This creates a “racetrack” translation path on the interior. The other four node modules are docked at the center of the Hab and Lab modules, two on each side, creating another “racetrack” translation path perpendicular to the first one. The DSSV has a generally vertical orientation. Within the Hab and Lab modules the decks are perpendicular to the longitudinal axis. The node modules are oriented with their longitudinal axes perpendicular to those of the Hab and Lab modules, so the nodes have a horizontal internal orientation. Decks are numbered one through nine, with decks two and eight representing the “top” and “bottom” domes of the Hab and Lab modules. The Hab Module decks encompass the ship’s galley, crew quarters, waste, hygiene, portions of crew exercise, and group recreation. The Lab Module contains food production facilities, the life science lab, the ship’s infirmary, the physical science lab, and the maintenance and fabrication workshop. The Node Modules serve a number of different functions. The two Exercise Nodes are docked to deck five of both the Hab and Lab modules and contain most of the aerobic and resistive exercise devices. Also docked to deck five but on the opposite side of the Hab and Lab modules are the Observation Deck and Space Café. These two node modules provide social gathering space for small numbers of crew. The Mission Operations Node is on deck nine directly above the Galley and contains spacecraft monitoring and commanding capabilities. Docked to it is the EVA Operations Node, which contains suit maintenance and storage. (The airlock is a separate, external element docked to the EVA Operations Node.) The Subsystems Node is on deck one beneath the maintenance and fabrication workshop. Docked to it is the Stowage Node. This node does not house DSSV primary stowage, but is a staging point where stowage brought in from logistics modules can be sorted, unpacked, or repacked as needed prior to distribution to the appropriate sections of the spacecraft.

Deep Space Habitat↗

NASA NTRSDate not supplied

Flow Boiling & Condensation Experiment (FBCE): Flow Boiling in Earth Gravity and Onboard the International Space Station

Two phase thermal management systems that capitalize on both latent and sensible heats of the working fluid can yield orders of magnitude enhancements in flow boiling and condensation heat transfer coefficients and reduce size and weight of future space systems. Because the understanding of microgravity influences on two-phase flow and heat transfer is quite limited, there is presently an urgent need for a new experimental microgravity facility to enable investigators to perform long-duration flow boiling and condensation experiments in pursuit of reliable databases. This presentation will discuss results from the Flow Boiling and Condensation Experiment (FBCE), a collaborative effort between Purdue University and NASA Glenn Research Center. Experiments have been performed using the final system with the Flow Boiling Module (FBM) in vertical orientation in Earth gravity (Mission Sequence Tests, MST) and in microgravity onboard the International Space Station (ISS). High-speed-video flow visualization, heat transfer, and critical heat flux (CHF) results from the MST are presented for both subcooled liquid and saturated liquid-vapor inlet conditions. CHF predictions made using the Interfacial Lift-off Model are compared with a consolidated database made by compiling FBM datasets obtained in prior years for different orientations in Earth gravity and on parabolic flights. New explicit correlations for CHF and subcooled flow boiling heat transfer coefficient are developed and shown to be excellent in their predictive accuracies against consolidated experimental databases. Computations are performed for flows in microgravity and horizontal flows in Earth gravity, the results of which show a good predictive accuracy for both void fraction and wall temperature. Finally, similar preliminary results from the recent ISS experiments are presented.

Issam Mudawar↗

NASA NTRSDate not supplied

Predictions of Line Chilldown Boiling Regime Transitions by a Coupled CFD-Sub-Grid Boiling Model Validated against 1G LN2 Experiments

Propellant storage and transfer during future long-duration missions will involve fuel depot operations in which a donor depot tank is used to fill a receiver spacecraft tank with a cryogenic propellant. Prior to the on-Orbit filling operation both the receiver tank and the transfer line must be cooled. The line chilldown process involves transition between boiling regimes in microgravity that will be quite different from their 1g ground-based counterparts. Since the cryogenic propellant itself will be used to perform the chilldown process, the time constants to cool the wall and the amount of fuel that will be used become important design considerations. In this light, the focus of the present work is to capture the flow boiling characteristics of a cryogenic fluid, namely, liquid nitrogen, during the chill-down of a transfer line using CFD modelling and simulations. The cryogenic chill-down process involves different flow boiling regimes: film boiling, transition boiling and nucleate boiling. The prediction of transition between these regimes in a CFD framework is new and challenging. The present work addresses this challenge by employing a volume-of-fluid (VOF) based methodology with Lee phase change model to predict the film boiling regime of the chill-down process in ANSYS Fluent®. The transition and nucleate boiling regimes are predicted by incorporating a sub-grid model that accounts for bubble nucleation, growth, shedding frequency, and departure diameter. The sub-grid model is implemented into Fluent via a user-defined function for wall-fluid heat flux calculations. The sub-grid model is similar in formulation to the well-known Rensselaer Polytechnic Institute (RPI) boiling model. The CFD model is validated against published experimental data for liquid nitrogen chill-down of a heated stainless-steel pipe in 1g. Predicted results shows good agreement of wall temperature, rewetting temperature, and transition between film and nucleate boiling with the experimental measurements for several different LN2 flowrates in the vertical orientation. The strengths and weaknesses of this modeling approach are presented and discussed.

Cryogenic Fluid Management↗

NASA NTRS1979

Effect of outboard vertical-fin position and orientation on the low-speed aerodynamic performance of highly swept wings

A theoretical study was conducted to determine the potential low-speed performance improvements which can be achieved by altering the position and orientation of the outboard vertical fins of low-aspect-ratio highly swept wings. Results show that the magnitude of the performance improvements is solely a function of the span-load distribution. Both the vertical-fin-chordwise position and toe angle provided effective means for adjusting the overall span-load distribution.

Johnson, V. S.↗

NASA NTRS2014

Diagenetic Features in Yellowknife Bay, Gale Crater, Mars: Implications for Substrate Rheology and Potential Gas Release

Multiple diagenetic features have been observed in clay-bearing mudstone exposed within Yellowknife Bay, Gale Crater, Mars. These features occurred during at least two separate episodes: an early generation of spheroidal concretions that co-occur with a dense networks of mineralized fractures, and a later generation of mineralized veins. Concretions consist of mm-sized spheroids (0.4 to 8.0 mm, mean diameter of 1.2 mm) that are distinctly more resistant than the encompassing mudstone. Dissected spheroids suggest an origin via compaction and incipient lithification of the substrate at the perimeter of syndepositional void space. Concretions are generally patchy in their distribution within clay-‐bearing mudstone, but in places can be the dominant fabric element. Locally dense networks of mineralized fractures occur in regions of low concretion abundance. These consist of short (< 50 cm), curvilinear to planar mineralized voids that occur across a range of orientations from vertical to subhorizontal. Fractures are filled by multi-phase cement consisting of two isopachous, erosionally resistant outer bands, and a central less resistant fill. Physical relationships suggests that original fractures may have formed as both interconnected voids and as discrete cross--cutting features. Co--occurrence of early diagenetic concretions and fracture networks suggests a common origin via gas release within a subaqueous, shallow substrate. We suggest that gas release within weakly cohesive subsurface sediments resulted in substrate dewatering and an increase in the cohesive strength of the substrate. Local differences in substrate strength and rate of gas production would have result in formation of either discrete voids or fracture networks. A second generation of mineralized veins is characterized by a regionally low spatial density, predominantly vertical or horizontal orientations, and a single phase of Ca-‐sulfate mineral fill. These veins cross-cut the early diagenetic elements and intersect a greater thickness of stratigraphy within Yellowknife Bay, suggesting a later-‐diagenetic origin via hydraulic fracturing.

Kah, L. C.↗

NASA NTRS1986

Cytochemical localization of calcium in cap cells of primary roots of Zea mays L

The distribution of calcium (Ca) in caps of vertically- and horizontally-oriented roots of Zea mays was monitored to determine its possible role in root graviresponsiveness. A modification of the antimonate precipitation procedure was used to localize Ca in situ. In vertically-oriented roots, the presumed graviperceptive (i.e., columella) cells were characterized by minimal and symmetric staining of the plasmalemma and mitochondria. No precipitate was present in plasmodesmata or cell walls. Within 5 min after horizontal reorientation, staining was associated with the portion of the cell wall adjacent to the distal end of the cell. This asymmetric staining persisted throughout the onset of gravicurvature. No staining of lateral cell walls of columella cells was observed at any stage of gravicurvature, suggesting that a lateral flow of Ca through the columella tissue of horizontally-oriented roots does not occur. The outermost peripheral cells of roots oriented horizontally and vertically secrete Ca through plasmodesmata-like structures in their cell walls. These results are discussed relative to proposed roles of root-cap Ca in root gravicurvature.

NASA Discipline Plant Biology↗

NASA NTRSDate not supplied

Experimental Setup for Mechanically Testing Subscale Triangular, Rollable, and Collapsible Deployable Composite Booms

High-strain composite deployable space structures are used for space infrastructure and science applications such as solar array supports, antennae, camera masts, and lightweight structures supporting solar sailing propulsion ele-ments. Triangular, Rollable, and Collapsible (TRAC) deployable composite booms are one example of a high-strain composite deployable structure and were studied using novel experimental test and characterization methods developed under the Gravity Offloading and Analysis of Long Imperfection-sensitive Ele-ments (GOALIE) project. In the present work, a subscale 7-m-long TRAC boom was suspended vertically to orient gravity along the length of the boom. By ori-enting vertically, highly nonlinear and unstable behavior often encountered dur-ing horizontally oriented gravity offload testing of similar structures was reduced. Pretest analytical predictions of TRAC booms indicated three unique failure modes, loads, and locations for three unique loading cases of in-plane bending, out-of-plane bending, and axial compression. To investigate the predicted behav-ior, an experimental test was set up to impart mechanical loads to a subscale TRAC boom. The experimental setup, loading cases, and instrumentation used to characterize the mechanical response of a subscale TRAC boom are described in this paper.

High-strain composites↗

NASA NTRS1993

Robotic Variable Polarity Plasma Arc (VPPA) Welding

The need for automated plasma welding was identified in the early stages of the Space Station Freedom Program (SSFP) because it requires approximately 1.3 miles of welding for assembly. As a result of the Variable Polarity Plasma Arc Welding (VPPAW) process's ability to make virtually defect-free welds in aluminum, it was chosen to fulfill the welding needs. Space Station Freedom will be constructed of 2219 aluminum utilizing the computer controlled VPPAW process. The 'Node Radial Docking Port', with it's saddle shaped weld path, has a constantly changing surface angle over 360 deg of the 282 inch weld. The automated robotic VPPAW process requires eight-axes of motion (six-axes of robot and two-axes of positioner movement). The robot control system is programmed to maintain Torch Center Point (TCP) orientation perpendicular to the part while the part positioner is tilted and rotated to maintain the vertical up orientation as required by the VPPAW process. The combined speed of the robot and the positioner are integrated to maintain a constant speed between the part and the torch. A laser-based vision sensor system has also been integrated to track the seam and map the surface of the profile during welding.

Jaffery, Waris S.↗

NASA NTRS2019

Analysis of the Global Microwave Polarization Data of Clouds

Two NASA microwave radiometers, the satellite-borne GPM (Global Precipitation Measurement) Microwave Imager (GMI) and the aircraft-borne CoSMIR (the Conical Scanning Millimeter-wave Imaging Radiometer), measure vertically- and horizontally-polarized microwaves emitted by cloud particles and the Earth below, providing unique information on ice crystal properties in clouds. Their data reveal that non-spherical ice crystals are common and they fall in a preferred horizontally aligned orientation in convective and optically thick clouds especially near cloud top. A bin (particle-size-resolving) microphysical model with an ice crystal shape representation is developed to simulate the evolution of ice crystal properties (i.e., size, shape and orientation), where the radiation effect on microphysics (REM) is taken into account. Since REM represents the effect of all (e.g., both infrared and solar) radiation on ice crystal temperature, it relies upon the ice crystal proprieties that determine how an ice crystal receives radiation. Definitely, REM is different from the radiative effects that cause sensitivity at the microwave frequencies in the GPM and CoSMIR observations. Model results show that horizontally-oriented ice crystals grow faster than vertically-oriented (or spherical) ones due to REM. When both horizontally- and vertically-oriented ice crystals coexist in an air parcel, the model results show that the former grow by vapor deposition whereas the latter shrink by sublimation and disappear eventually. These modeling results are supported by the GMI data and the CoSMIR observations from MC3E (Midlatitude Continental Convective Clouds Experiment) and OLYMPEX (Olympic Mountains Experiment) on the prevalence of horizontally-oriented ice crystals. Moreover, the REM-induced precipitation explains the CloudSat observations of rare thin clouds in the tropical mid-troposphere as well as the common diamond dust in the high latitudes.

Xiping Zeng↗

NASA NTRS2014

Range Safety Flight Elevation Limit Calculation Software

This program was developed to fill a need within the Wallops Flight Facility workflow for automation of the development of vertical plan limit lines used by flight safety officers during the conduct of expendable launch vehicle missions. Vertical plane present-position-based destruct lines have been used by range safety organizations at numerous launch ranges to mitigate launch vehicle risks during the early phase of flight. Various ranges have implemented data submittal and processing workflows to develop these destruct lines. As such, there is significant prior art in this field. The ElLimits program was developed at NASA's Wallops Flight Facility to automate the process for developing vertical plane limit lines using current computing technologies. The ElLimits program is used to configure launch-phase range safety flight control lines for guided missiles. The name of the program derives itself from the fundamental quantity that is computed - flight elevation limits. The user specifies the extent and resolution of a grid in the vertical plane oriented along the launch azimuth. At each grid point, the program computes the maximum velocity vector flight elevation that can be permitted without endangering a specified back-range location. Vertical plane x-y limit lines that can be utilized on a present position display are derived from the flight elevation limit data by numerically propagating 'streamlines' through the grid. The failure turn and debris propagation simulation technique used by the application is common to all of its analysis options. A simulation is initialized at a vertical plane grid point chosen by the program. A powered flight failure turn is then propagated in the plane for the duration of the so-called RSO reaction time. At the end of the turn, a delta-velocity is imparted, and a ballistic trajectory is propagated to impact. While the program possesses capability for powered flight failure turn modeling, it does not require extensive user inputs of vehicle characteristics (e.g., thrust and aerodynamic data), nor does it require reams of turn data after the traditional fashion of the Air Force ranges. The program requires a nominal trajectory table (time, altitude, range, velocity, and flight elevation) and makes heavy use of it to initialize and model a failure turn.

Lanzi, Raymond J↗

NASA NTRS1984

Effects of Vegetation Canopy Structure on Microwave Scattering

The role of canopy structure on microwave backscattering is studied. Structure refers to the size, orientation, and vertical placement of scatterers in the canopy. Models to predict the backscattering coefficient, SIGMAO, of vegetation with explicit biophysical and explicit polarization-dependent parameters were developed. Preparation for field measurements with radar scatterometers was completed. Technical progress included: (1) the modification of the Attema and Ulaby (1977) model and its multilayer variation by Hoekman et al. (1983) to include polarization explicitly (i.e., to allow for separate backscattering cross sections, SIGMA, and extinction cross sections, Q, for each polarization), (2) the investigation of the modified model to isolate canopy element orientation parameters by the rationing of SIGMAO measurements for different polarization combinations, (3) the development of expressions for bistatic scattering and canopy-substrate scattering to supplement the models, (4) the performance of sensitivity analyses on these models, (5) the modification of the Attema and Ulaby model to alloy for changes, (6) the use of the modified model with a seasonal corn data set from Kansas (Eger et al., 1983), and (7) the initiation of preparations for empirical measurements with radar spectrometer and the Mobile Radar Scatterometer in irrigated cropland to test the models.

Paris, J. F.↗