Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Performance of supersonic scoop inlets

A brief summary is made of the performance of a series of variable-geometry type scoop inlets investigated at the Lewis Laboratory on a model of the X-3 airplane fuselage. Data are presented for a range of inlet mass-flow ratios over a Mach number range from 0 to 2 and from 0 degrees to 12 degrees angle of attack. Rounded-lip inlets are found to give satisfactory performance to a Mach number of 1.5. Use of sharp rather than blunt lip configurations is shown to provide considerable gains in available thrust at Mach number 2.0 but penalize take-off performance to the extent that auxiliary air intakes may be required. No one inlet type was found to be superior over the entire range of operating variables. Thus, the choice of a specific inlet design will be influenced by structural and mechanical as well as aerodynamic considerations.

DIFFUSERS, SUPERSONIC↗
NASA NTRS2001

The Plasma Wave Environment of Europa

The Galileo spacecraft has executed nine close flybys of Jupiter's moon Europa for which plasma wave observations were obtained. This paper presents an analysis of the observations from these flybys taking into consideration the variable geometry of the trajectories in an attempt to characterize the general plasma-wave environment associated with the interaction of the Jovian magnetosphere with the moon. A wide variety of plasma-wave phenomena are found to be associated with this interaction. While there are apparently temporal variations which complicate the analysis, a crude model of the distribution of these phenomena around Europa is derived. Primarily on the upstream side of Europa, and working inward to the moon, electron-cyclotron harmonics are first observed, followed by a region within about two Europa radii of the moon with whistler-mode hiss or chorus, and culminating in a region closest to the moon where a band at the upper hybrid resonance frequency is sometimes enhanced over its ambient intensity. The wake region is approximately two Europa radii across and comprises a broadband, highly variable, and bursty electrostatic phenomenon. Upon closer inspection, these bursty emissions appear as solitary structures similar to those in Earth's auroral zone and plasma sheet boundary layer. In addition to the survey of wave phenomena in the vicinity of Europa, we provide density profiles derived primarily from the upper hybrid resonance frequency which is readily apparent throughout most of each of the flybys. Finally, we suggest that the whistler mode, electron cyclotron harmonic, and upper hybrid resonance emissions are driven by some combination of factors including variations in the magnetic field near Europa and the loss and production of plasma at Europa as a result of the interaction of the Jovian magnetosphere with the moon. By analogy with studies of the ion and electron holes and broadband electrostatic noise at Earth and Jupiter, we argue that the electrostatic solitary structures in the wake are associated with currents and beams coupling Europa to Jupiter's ionosphere.

Kurth, W. S.↗
NASA NTRS2014

Engine Power Turbine and Propulsion Pod Arrangement Study

A study has been conducted for NASA Glenn Research Center under contract NNC10BA05B, Task NNC11TA80T to identify beneficial arrangements of the turboshaft engine, transmissions and related systems within the propulsion pod nacelle of NASA's Large Civil Tilt-Rotor 2nd iteration (LCTR2) vehicle. Propulsion pod layouts were used to investigate potential advantages, disadvantages, as well as constraints of various arrangements assuming front or aft shafted engines. Results from previous NASA LCTR2 propulsion system studies and tasks performed by Boeing under NASA contracts are used as the basis for this study. This configuration consists of two Fixed Geometry Variable Speed Power Turbine Engines and related drive and rotor systems (per nacelle) arranged in tilting nacelles near the wing tip. Entry-into-service (EIS) 2035 technology is assumed for both the engine and drive systems. The variable speed rotor system changes from 100 percent speed for hover to 54 percent speed for cruise by the means of a two speed gearbox concept developed under previous NASA contracts. Propulsion and drive system configurations that resulted in minimum vehicle gross weight were identified in previous work and used here. Results reported in this study illustrate that a forward shafted engine has a slight weight benefit over an aft shafted engine for the LCTR2 vehicle. Although the aft shafted engines provide a more controlled and centered CG (between hover and cruise), the length of the long rotor shaft and complicated engine exhaust arrangement outweighed the potential benefits. A Multi-Disciplinary Analysis and Optimization (MDAO) approach for transmission sizing was also explored for this study. This tool offers quick analysis of gear loads, bearing lives, efficiencies, etc., through use of commercially available RomaxDESIGNER software. The goal was to create quick methods to explore various concept models. The output results from RomaxDESIGNER have been successfully linked to Boeing spreadsheets that generate gear tooth geometry in Catia 3D environment. Another initial goal was to link information from RomaxDESIGNER (such as hp, rpm, gear ratio) to populate Boeing's parametric weight spreadsheet and create an automated method to estimate drive system weight. This was only partially achieved due to the variety of weight models, number of manual inputs, and qualitative assessments required. A simplified weight spreadsheet was used with data inputs from RomaxDESIGNER along with manual inputs to perform rough weight calculations.

Robuck, Mark↗
NASA NTRS2017

Imaging a Free-Geometry Magma Reservoir Using FEM-Based Linear Inverse Modeling of InSAR Data: Application to Rabaul Caldera, Papua New Guinea

We test an innovative inversion scheme using Green’s functions from an array of pressure sources embedded in finite-element method (FEM) models to image, without assuming an a-priori geometry, the composite and complex shape of a volcano deformation source. We invert interferometric synthetic aperture radar (InSAR) data to estimate the pressurization and shape of the magma reservoir of Rabaul caldera, Papua New Guinea. The results image the extended shallow magmatic system responsible for a broad and long-term subsidence of the caldera between 2007 February and 2010 December. Elastic FEM solutions are integrated into the regularized linear inversion of InSAR data of volcano surface displacements in order to obtain a 3-D image of the source of deformation. The Green’s function matrix is constructed from a library of forward line-of-sight displacement solutions for a grid of cubic elementary deformation sources. Each source is sequentially generated by removing the corresponding cubic elements from a common meshed domain and simulating the injection of a fluid mass flux into the cavity, which results in a pressurization and volumetric change of the fluidfilled cavity. The use of a single mesh for the generation of all FEM models avoids the computationally expensive process of non-linear inversion and remeshing a variable geometry domain. Without assuming an a-priori source geometry other than the configuration of the 3-D grid that generates the library of Green’s functions, the geodetic data dictate the geometry of the magma reservoir as a 3-D distribution of pressure (or flux of magma) within the source array. The inversion of InSAR data of Rabaul caldera shows a distribution of interconnected sources forming an amorphous, shallow magmatic system elongated under two opposite sides of the caldera. The marginal areas at the sides of the imaged magmatic system are the possible feeding reservoirs of the ongoing Tavurvur volcano eruption of andesitic products on the east side and of the past Vulcan volcano eruptions of more evolved materials on the west side. The interconnection and spatial distributions of sources correspond to the petrography of the volcanic products described in the literature and to the dynamics of the single and twin eruptions that characterize the caldera. The ability to image the complex geometry of deformation sources in both space and time can improve our ability to monitor active volcanoes, widen our understanding of the dynamics of active volcanic systems and improve the predictions of eruptions.

Inverse theory↗
NASA NTRS2017

Imaging the Complex Geometry of a Magma Reservoir Using Fem-Based Linear Inverse Modeling of InSAR Data: Application to Rabaul Caldera, Papua New Guinea

We test an innovative inversion scheme using Green’s functions from an array of pressure sources embedded in finite-element method (FEM) models to image, without assuming an a-priori geometry, the composite and complex shape of a volcano deformation source. We invert interferometric synthetic aperture radar (InSAR) data to estimate the pressurization and shape of the magma reservoir of Rabaul caldera, Papua New Guinea. The results image the extended shallow magmatic system responsible for a broad and long-term subsidence of the caldera between 2007 February and 2010 December. Elastic FEM solutions are integrated into the regularized linear inversion of InSAR data of volcano surface displacements in order to obtain a 3-D image of the source of deformation. The Green’s function matrix is constructed from a library of forward line-of-sight displacement solutions for a grid of cubic elementary deformation sources. Each source is sequentially generated by removing the corresponding cubic elements from a common meshed domain and simulating the injection of a fluid mass flux into the cavity, which results in a pressurization and volumetric change of the fluid-filled cavity. The use of a single mesh for the generation of all FEM models avoids the computationally expensive process of non-linear inversion and remeshing a variable geometry domain. Without assuming an a-priori source geometry other than the configuration of the 3-D grid that generates the library of Green’s functions, the geodetic data dictate the geometry of the magma reservoir as a 3-D distribution of pressure (or flux of magma) within the source array. The inversion of InSAR data of Rabaul caldera shows a distribution of interconnected sources forming an amorphous, shallow magmatic system elongated under two opposite sides of the caldera. The marginal areas at the sides of the imaged magmatic system are the possible feeding reservoirs of the ongoing Tavurvur volcano eruption of andesitic products on the east side and of the past Vulcan volcano eruptions of more evolved materials on the west side. The interconnection and spatial distributions of sources correspond to the petrography of the volcanic products described in the literature and to the dynamics of the single and twin eruptions that characterize the caldera. The ability to image the complex geometry of deformation sources in both space and time can improve our ability to monitor active volcanoes, widen our understanding of the dynamics of active volcanic systems and improve the predictions of eruptions.

Inverse theory↗
NASA NTRS2011

High-Temperature Smart Structures for Engine Noise Reduction and Performance Enhancement

One of key NASA goals is to develop and integrate noise reduction technology to enable unrestricted air transportation service to all communities. One of the technical priorities of this activity has been to account for and reduce noise via propulsion/airframe interactions, identifying advanced concepts to be integrated with the airframe to mitigate these noise-producing mechanisms. An adaptive geometry chevron using embedded smart structures technology offers the possibility of maximizing engine performance while retaining and possibly enhancing the favorable noise characteristics of current designs. New high-temperature shape memory alloy (HTSMA) materials technology enables the devices to operate in both low-temperature (fan) and high-temperature (core) exhaust flows. Chevron-equipped engines have demonstrated reduced noise in testing and operational use. It is desirable to have the noise benefits of chevrons in takeoff/landing conditions, but have them deployed into a minimum drag position for cruise flight. The central feature of the innovation was building on rapidly maturing HTSMA technology to implement a next-generation aircraft noise mitigation system centered on adaptive chevron flow control surfaces. In general, SMA-actuated devices have the potential to enhance the demonstrated noise reduction effectiveness of chevron systems while eliminating the associated performance penalty. The use of structurally integrated smart devices will minimize the mechanical and subsystem complexity of this implementation. The central innovations of the effort entail the modification of prior chevron designs to include a small cut that relaxes structural stiffness without compromising the desired flow characteristics over the surface; the reorientation of SMA actuation devices to apply forces to deflect the chevron tip, exploiting this relaxed stiffness; and the use of high-temperature SMA (HTSMA) materials to enable operation in the demanding core chevron environment. The overall conclusion of these design studies was that the cut chevron concept is a critical enabling step in bringing the variable geometry core chevron within reach. The presence of the cut may be aerodynamically undesirable in some respects, but it is present only when the chevron is not immersed in the core jet exhaust. When deployed, the gap closes as the chevron tip enters the high-speed, high-temperature core stream. Aeroacoustic testing and flow visualization support the contention that this cut is inconsequential to chevron performance.

Quackenbush, Todd R.↗
NASA NTRS1959

A Survey of Hypersonic-Ramjet Concepts

A brief discussion is presented of the major problem areas involved in the development of a hypersonic ramjet engine. Keeping the structural temperature to an acceptably low level is the severest problem expected. A rapid survey is made of some of the relatively unconventional concepts that may find application in the hypersonic region. These include supersonic combustors, underwing burning, atmospheric-recombination, engine installation, nuclear power, variable geometry, and fuel-rich operation.

Weber, R. J.↗
NASA NTRS1972

Research trends in turbine aerodynamics

Recent trends in turbine aerodynamics are summarized. Areas discussed include cooled turbine aerodynamics, high work factor turbines, pneumatic variable geometry, and computer analyses.

Stewart, W. L.↗
NASA NTRS1971

Airbreathing propulsion system trends.

Among trends in airbreathing propulsion, the priority is shown to belong to the goal of quieting engines to a level no greater than the natural background noise level of the environment in which they operate. For military engines, not so severely noise-constrained, the possibility of stoichiometric gas-turbine engines is shown to be within reach. Very high bypass ratio propfans are especially suitable for V/STOL aircraft. Evolution of reliable variable-geometry inlets and exhaust nozzles characterizes trends in the supersonic regime.

Dugan, J. F., Jr.↗
NASA NTRS1972

Research trends in turbine aerodynamics.

Brief description of some of the recent trends in turbine aerodynamics research. Areas covered include cooled turbine aerodynamics, high work-factor turbines, pneumatic variable geometry, and computer analysis. Most of this research is shown to have been directed primarily toward allowing the turbine to accept efficiently higher inlet temperatures and blade loading.

Stewart, W. L.↗
NASA NTRS1973

A summary of current research in rotor unsteady aerodynamics with emphasis on work at Langley Research Center

The basic unsteady aerodynamic environment of the rotary wing is summarized. Some of the observed trends in the state of the art are discussed. Some of the research needs that will require attention are reported. A review of a number of research investigations as a part of a joint NASA/Army rotorcraft project is presented. The research is directed toward achieving a better understanding of rotor unsteady airfoils. The investigations include: (1) rotor maneuver loads; (2) level flight and maneuver wake prediction; (3) tip-vortex flow; (4) blade-vortex interactions; (5) dynamic stall; (6) transient Mach number air loads; and (7) development of variable geometry rotors.

Ward, J. F.↗
NASA NTRS1974

Reversed cowl-flap thrust augmentor

Inlet mouthpiece with variable geometry improves low-speed performance of inlet (or ejector) of jet engines by use of reversed cowl-flap mechanism. Flaps can be adjusted mechanically or system can be operated with pressure taps set so pressure on inlet face is always smaller than pressure on back of inlet.

Cheng, D. Y.↗
NASA NTRS1973

Study of methods of improving the performance of the Langley Research Center Transonic Dynamics Tunnel (TDT)

A study has been made of possible ways to improve the performance of the Langley Research Center's Transonic Dynamics Tunnel (TDT). The major effort was directed toward obtaining increased dynamic pressure in the Mach number range from 0.8 to 1.2, but methods to increase Mach number capability were also considered. Methods studied for increasing dynamic pressure capability were higher total pressure, auxiliary suction, reducing circuit losses, reduced test medium temperature, smaller test section and higher molecular weight test medium. Increased Mach number methods investigated were nozzle block inserts, variable geometry nozzle, changes in test section wall configuration, and auxiliary suction.

Source record↗
NASA NTRS1974

Determination of propulsion-system-induced forces and moments of a Mach 3 cruise aircraft

During the joint NASA/USAF flight research program with the YF-12 airplane, the Dutch roll damping was found to be much less during automatic inlet operation than during fixed inlet operation at Mach numbers greater than 2.5 and with the yaw stability augmentation system off. It was concluded that the significant reduction in Dutch roll damping was due to the forces and moments induced by the variable-geometry features of the inlet. Two stability-derivative extraction techniques were applied to the flight data; the recently developed Newton-Raphson technique and the time vector method. These techniques made it possible to determine the forces and moments generated by spike and bypass door movement.

Gilyard, G. B.↗
NASA NTRS1972

Fastening on the F-14A for cost effective fatigue resistance

Cost effectiveness airframe considerations dictated a variable geometry wing design that requires weight optimization, maximum working stress resistance and minimum fatigue concentration factors. The extensive use of titanium structural materials employed electron beam welding methods and interference fit fastening techniques as principle mechanical joining means for economic F-14A production and reliability engineering.

Beal, B. H.↗