Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Sol-gel derived silicate-phosphate glass SiO 2 –P 2 O 5 –CaO–TiO 2 : The effect of titanium isopropoxide on porosity and thermomechanical stability

Despite of several decades lasting extensive research of bioactive and bioresorbable glasses the systematic parametrization and determination of the key factors affecting porosity and thermomechanical characteristics still remains challenging. Here, we present silica-phosphate glasses, with the composition 70SiO 2 - 20P 2 O 5 - (10-x)CaO-xTiO 2 (mol%; x = 0, 2.5, 5, and 7.5), prepared by sol -gel method and reinforced by titanium dioxide via titanium isopropoxide (TTIP) incorporation which demonstrated tunable variation of porosity from micro-to macro -region and superb mechanical integrity during the calcination process. The presence of 7.5 mol% TiO 2 promotes dimensional stability up to 1000°C as investigated by thermomechanical analysis. The XRD showed the dominant presence of silicon phosphate [Si(P 2 O 7 )], titanium phosphate [Ti(P 2 O 7 )] and calcium phosphates [β-Ca(P 2 O 6 ) and γ- Ca 2 (P 2 O 7 )]. The effect of TiO 2 doping on the multiscale morphology and porosity was investigated by means of SEM, MIP, μCT, N 2 adsorption and USAXS/SAXS. Increasing TiO 2 content leads to the formation of open porosity up to 70vol% and drives the formation of a refined interconnected macroporosity of 2-30 μm. In contrast, mesoporosity with a dominance of 3-6nm pores decreases in all samples with increasing TiO 2 content. USAXS/SAXS revealed an increase in primary particle size with increasing TiO 2 content which is in good agreement with the nitrogen physisorption analysis showing that microporosity decreases with increasing TiO2 content.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elimination of oxygen sensitivity in α-titanium by substitutional alloying with Al

Individually, increasing the concentration of either oxygen or aluminum has a deleterious effect on the ductility of titanium alloys. For example, extremely small amounts of interstitial oxygen can severely deteriorate the tensile ductility of titanium, particularly at cryogenic temperatures. Likewise, substitutional aluminum will decrease the ductility of titanium at low-oxygen concentrations. Here, we demonstrate that, counter-intuitively, significant additions of both Al and O substantially improves both strength and ductility, with a 6-fold increase in ductility for a Ti-6Al-0.3 O alloy as compared to a Ti-0.3 O alloy. The Al and O solutes act together to increase and sustain a high strain-hardening rate by modifying the planar slip that predominates into a delocalized, three-dimensional dislocation pattern. Furthermore, the mechanism can be attributed to decreasing stacking fault energy by Al, modification of the “shuffle” mechanism of oxygen-dislocation interaction by the repulsive Al-O interaction in Ti, and micro-segregation of Al and O by the same cause.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tunable electrochromic behavior of titanium-based MXenes

Two-dimensional transition metal carbides, nitrides and carbonitrides, popular by the name MXenes, are a promising class of materials as they exhibit intriguing optical, optoelectronic and electrochemical properties. Taking advantage of their metallic conductivity and hydrophilicity, titanium carbide MXenes (Ti 3 C 2 T x and others) are used to fabricate solution processable transparent conducting electrodes (TCEs) for the design of three-electrode electrochromic cells. However, the tunable electrochromic behavior of various titanium-based MXene compositions across the entire visible spectrum has not yet been demonstrated. Here, we investigate the intrinsic electrochromic properties of titanium-based MXenes, Ti 3 C 2 T x , Ti 3 CNT x , Ti 2 CT x , and Ti 1.6 Nb 0.4 CT x , where individual MXenes serve as a transparent conducting, electrochromic, and plasmonic material layer. Plasmonic extinction bands for Ti 3 C 2 T x , Ti 2 CT x and Ti 1.6 Nb 0.4 CT x are centered at 800, 550 and 480 nm, which are electrochemically tunable to 630, 470 and 410 nm, respectively, whereas Ti 3 CNT x shows a reversible change in transmittance in the wide visible range. Additionally, the switching rates of MXene electrodes with no additional transparent conductor electrodes are estimated and correlated with the respective electrical figure of merit values. This work demonstrates that MXene-based electrochromic cells are tunable in the entire visible spectrum and suggests the potential of the MXene family of materials in optoelectronic, plasmonic, and photonic applications, such as tunable visible optical filters and modulators, to name a few.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Titanium surface nitriding by sodium amide in molten salts

A crystalline titanium nitride (TiN) layer on titanium foil is achieved using sodium amide (NaNH 2 ) as a nitrogen source in LiCl–KCl molten salts. Nanoindentation testing revealed exceptional mechanical properties, with the nitrided surface achieving a hardness of approximately 20.6 GPa, representing more than a four-fold increase compared to the untreated titanium substrate.

Wang, Tao [Oak Ridge National Laboratory (ORNL), O↗
DOE OSTI2021

Spectroscopic signature of negative electronic compressibility from the Ti core-level of titanium carbonitride MXene

Two-dimensional transition metal carbides, carbonitrides, and nitrides called MXenes exhibit high metallic conductivity, ion intercalation capability and reversible redox activity, prompting their applications in energy storage and conversion, electromagnetic interference (EMI) shielding, and electronics, among many other fields. It has been shown that replacement of about 50% of carbon atoms in the most popular MXene family member, titanium carbide (Ti 3 C 2 T x ), by nitrogen atoms, forming titanium carbonitride (Ti 3 CNT x ), leads to drastically different properties, such as very high negative charge in solution and extreme EMI shielding effectiveness, exceeding all known materials, even metals at comparable thicknesses. Here, by using ultraviolet photoemission spectroscopy (UPS), the electronic structures of Ti 3 CNT x and Ti 3 C 2 T x are systematically investigated and compared as a function of charge carrier density. We observe that, in contrast to Ti 3 C 2 T x , the Ti 3p core-level of Ti 3 CNT x exhibits a counterintuitive shift to a lower binding energy of up to approximately 250 meV upon increasing the electron density, which is a spectroscopic signature of negative electronic compressibility (NEC). These experimentally measured chemical potential shifts are well-captured by the density functional theory (DFT) calculation. The DFT results also further suggest that the hybridization of titanium-nitrogen bonding in Ti 3 CNT x helps promoting the available states of Ti atoms for receiving more electron above the Fermi level and leads to the observed NEC. Furthermore, our findings explain the differences in electronic properties between the two very important and widely studied MXenes and also suggest a new strategy to apply the NEC effect of Ti 3 CNT x in energy and charge storage applications.

2D materials↗
DOE OSTI2023

Residual strain orientation in rolled titanium determined with synchrotron X-ray Laue microdiffraction

Previously, synchrotron X-ray Laue microdiffraction has been used to measure the magnitudes of residual strain in materials. Recently the method was advanced to determine the orientation of the strain ellipsoid and applied to naturally deformed quartzites; however, the deformation history of these quartzites is ambiguous due to their natural origin. Here, in this study, synchrotron X-ray Laue microdiffraction (µXRD) is used to measure the residual strain for the first time in a sample with known stress history, rolled titanium. A deviatoric strain tensor is calculated from each Laue diffraction image collected with two µXRD scans of a rolled titanium sheet in different sample orientations. The principal strain axes are calculated using an eigen decomposition of the deviatoric strain tensors. The results show that the principal axis of compression is aligned with the normal direction of the titanium sheet, and the principal axis of extension is aligned with the rolling direction. Pole figures are used to represent the 3D distribution of residual strain axes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Titanium Material Comparison for Second Target Station Moderators

Two titanium alloys, Ti 15-3-3-3 and Grade 5 Ti, have been analyzed for their neutronic differences after being exposed to neutron fluxes from a 5-year operational period in the Second Target Station (STS)moderators. There are several differences in the original composition of the two alloys where Ti 15-3-3-3contains Cr and Sn and Grade 5 Ti does not. The differences in original composition propagate through the analysis to yield discrepancies in decay power density and decay gamma intensity density of more than a factor of 3.5 at some times during operation. Immediately after the 5-year operational period, Ti 15-3-3-3has a factor of 3.59 higher intensity of high-energy decay gammas than Grade 5 Ti, and Ti 15-3-3-3 also has a factor of 3.53 higher decay power than Grade 5 Ti. After 1 year of shutdown, Ti 15-3-3-3 has a 48% higher intensity of high-energy decay gammas and a 86% greater decay power density when compared with Grade 5 Ti. The quantities-of-interest in this report are per unit volume and the overall volume of titanium should be considered when making engineering judgment on final titanium alloy selection.

36 MATERIALS SCIENCE↗
NASA NTRS1968

Titanium-nitrogen reaction investigated for application to gettering systems

Titanium is one of several gettering materials available for removing nitrogen from inert gases. The reaction rate of titanium-metal sponge and nitrogen in argon-nitrogen mixtures was studied at 900 degrees C. The rate was found to depend upon the partial pressure of nitrogen in the gas phase. Mathematical relationships simulate titanium systems.

Arntzen, J. D.↗
NASA NTRS1971

Compressive behavior of titanium alloy skin-stiffener specimens selectively reinforced with boron-aluminum composite

A method of selectively reinforcing a conventional titanium airframe structure with unidirectional boron-aluminum composite attached by brazing was successfully demonstrated in compression tests of short skin-stiffener specimens. In a comparison with all-titanium specimens, improvements in structural performance recorded for the composite-reinforced specimens exceeded 25 percent on an equivalent-weight basis over the range from room temperature to 700 K (800 F) in terms of both initial buckling and maximum strengths. Performance at room temperature was not affected by prior exposure at 588 K (600 F) for 1000 hours in air or by 400 thermal cycles between 219 K and 588 K (-65 F and 600 F). The experimental results were generally predictable from existing analytical procedures. No evidence of failure was observed in the braze between the boron-aluminum composite and the titanium alloy.

Herring, H. W.↗
NASA NTRS1971

The role of hydrogen in hot-salt stress corrosion cracking of titanium-aluminum alloys

Additional support is presented for the previously proposed role of hydrogen as an embrittling agent in hot-salt stress corrosion cracking of titanium-aluminum alloys. The main source of hydrogen formed during the reactions of titanium alloys with hot salt was identified as water associated with the salt. Hydrogen is produced by the reaction of an intermediate (hydrogen halide) with the alloy rather than from metal-water reactions. The fracture mode of precracked tensile specimens was ductile when the specimens were tested in air, and brittle when tests were made in high-pressure hydrogen. Stressed titanium-aluminum alloys also were cracked by bombardment with hydrogen ions produced in a proton accelerator. The approximate concentrations of the hydrogen ions in the alloys were calculated.

Ondrejcin, R. S.↗
NASA NTRS1971

Fabrication of the titanium transition ring of the Large Space Telescope (LST)

The fabrication of the titanium transition ring is summarized. The transition ring assembly was designed for the large space telescope and consists of two large titanium rings bolted together. The cross section dimensions of the assembly are 13-inches wide by 7-inches thick. The fabrication processes are discussed, and it is concluded that the work involved fabricating the largest titanium forging ever made.

Klein, L. A.↗
NASA NTRS1970

Properties of Hot Pressed Titanium Alloy Powders for Cryogenic Applications.

Evaluation of strength and toughness of hot-pressed titanium alloy powders at room and at cryogenic temperatures. The purpose was to determine how the mechanical properties of solid bodies formed from powder would compare with wrought specimens of the same size and with the same chemical analysis. It was found that of five titanium powder-making processes investigated, only the Rotating Electrode Process (REP) was capable of producing ELI-grade titanium alloy powder. Blocks hot-pressed from spherical REP powders had tensile properties equivalent to or better than those obtained from wrought bar.

Friedman, G. I.↗
NASA NTRS1973

Time exposure studies on stress corrosion cracking of aluminum 2014-T6, 2219-T87, 2014-T651, 7075-T651, and titanium 6Al-4V

The effect of a constant applied stress in crack initiation of aluminum 2014-T6, 2219-T87, 2014-T651, 7075-T651 and titanium 6Al-4V has been investigated. Aluminum c-ring specimens (1-inch diameter) and u-band titanium samples were exposed continuously to a 3.5% NaCl solution (pH 7) and organic fluids of ethyl, methyl, and iso-propyl alcohol (reagent purity), and demineralized distilled water. Corrosive action was observed to begin during the first and second day of constant exposure as evidenced by accumulation of hydrogen bubbles on the surface of stressed aluminum samples. However, titanium stressed specimens showed no reactions to its environment. Results of this investigation seems to suggest that aluminum 2014-T6, aluminum 7075-T651 and aluminum 2014-T651 are susceptible to stress corrosion cracking in chloride solution (NaCl), while aluminum 2219-T87 seem to resist stress corrosion cracking in sodium chloride at three levels of stress (25%, 50%, and 75% Y.S.). In organic fluids of methyl, ethyl, and iso-propyl alcohol, 2014-T6 and 7075-T651 did not fail by SCC; but 2014-T651 was susceptible to SCC in methly alcohol, but resistant in ethyl alcohol, iso-propyl alcohol and demineralized distilled water.

Terrell, J.↗
NASA NTRS1973

Aqueous chloride stress corrosion cracking of titanium: A comparison with environmental hydrogen embrittlement

The physical characteristics of stress corrosion cracking of titanium in an aqueous chloride environment are compared with those of embrittlement of titanium by a gaseous hydrogen environment in an effort to help contribute to the understanding of the possible role of hydrogen in the complex stress corrosion cracking process. Based on previous studies, the two forms of embrittlement are shown to be similar at low hydrogen pressures (100 N/sqm) but dissimilar at higher hydrogen pressures. In an effort to quantify this comparison, tests were conducted in an aqueous chloride solution using the same material and test techniques as had previously been employed in a gaseous hydrogen environment. The results of these tests strongly support models based on hydrogen as the embrittling species in an aqueous chloride environment. Further, it is shown that if hydrogen is the causal species, the effective hydrogen fugacity at the surface of titanium exposed to an aqueous chloride environment is equivalent to a molecular hydrogen pressure of approximately 10 N/sqm.

Nelson, H. G.↗
NASA NTRS1973

The effect of microstructure on the fracture toughness of titanium alloys

The high-strength titanium alloys are widely used in aircraft and aerospace structures due to their high strength to density ratios. In such applications, the fracture toughness rather than the strength is often the factor which requires larger size sections and lower useful payloads. The response of the strength and toughness of titanium alloys was analyzed generally without regard to the fracture mode or the effect of microstructure on the fracture mechanisms. Research on the fracture mechanisms in aluminum alloys and steels showed that the toughness may be improved by decreasing the sizes of inclusions and sub-micron precipitates. An investigation was conducted to study the fracture mechanisms in titanium alloys which may lead to suggestions for the improvement of the fracture toughness without a corresponding loss in strength.

Vanstone, R. H.↗
NASA NTRS1974

An investigation of chatter and tool wear when machining titanium

The low thermal conductivity of titanium, together with the low contact area between chip and tool and the unusually high chip velocities, gives rise to high tool tip temperatures and accelerated tool wear. Machining speeds have to be considerably reduced to avoid these high temperatures with a consequential loss of productivity. Restoring this lost productivity involves increasing other machining variables, such as feed and depth-of-cut, and can lead to another machining problem commonly known as chatter. This work is to acquaint users with these problems, to examine the variables that may be encountered when machining a material like titanium, and to advise the machine tool user on how to maximize the output from the machines and tooling available to him. Recommendations are made on ways of improving tolerances, reducing machine tool instability or chatter, and improving productivity. New tool materials, tool coatings, and coolants are reviewed and their relevance examined when machining titanium.

Sutherland, I. A.↗
NASA NTRS1974

Stress corrosion cracking of titanium alloys

The effect of hydrogen on the properties of metals, including titanium and its alloys, was investigated. The basic theories of stress corrosion of titanium alloys are reviewed along with the literature concerned with the effect of absorbed hydrogen on the mechanical properties of metals. Finally, the basic modes of metal fracture and their importance to this study is considered. The experimental work was designed to determine the effects of hydrogen concentration on the critical strain at which plastic instability along pure shear directions occurs. The materials used were titanium alloys Ti-8Al-lMo-lV and Ti-5Al-2.5Sn.

Statler, G. R.↗
NASA NTRS1972

Thin-film diffusion brazing of titanium alloys

A thin film diffusion brazing technique for joining titanium alloys by use of a Cu intermediate is described. The method has been characterized in terms of static and dynamic mechanical properties on Ti-6Al-4V alloy. These include tensile, fracture toughness, stress corrosion, shear, corrosion fatigue, mechanical fatigue and acoustic fatigue. Most of the properties of titanium joints formed by thin film diffusion brazing are equal or exceed base metal properties. The advantages of thin film diffusion brazing over solid state diffusion bonding and brazing with conventional braze alloys are discussed. The producibility advantages of this process over others provide the potential for producing high efficiency joints in structural components of titanium alloys for the minimum cost.

Mikus, E. B.↗