Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thin membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Deviation from Debye-Waller behavior in single crystalline freestanding Ni⁢ O membranes studied via ultrafast electron diffraction

Here, we realize single-crystal freestanding Ni⁢O films on Si⁢N membranes, enabling thin-film scattering experiments with little or no substrate background signal. These membrane samples provide a critical platform for performing ultrafast electron diffraction (UED) to probe the response of the lattice to laser excitation. We show that epitaxial Ni⁢O films on a water-soluble Sr 2 ⁢Ca⁢Al 2⁢ O 6 buffer layer on Sr⁢Ti⁢O 3 substrates can be transferred as freestanding films to the Si⁢N membranes while maintaining the epitaxial character of the films. An above-gap photoexcitation (𝜆 =266 nm) incident on the sample stimulates an initial lattice response of the order of 1.1 ps, followed by the persistence of this state for more than 20 ps. We observe typical Debye-Waller behavior in peaks with 𝑞 above the (220) family, but a distinct deviation from this behavior is seen in low-𝑞 peaks. We relate this behavior to a dynamic decrease in sample mosaicity in response to the optical pump of the order of 3% that endures for approximately 4 ps. We suspect that this dynamic mosaicity is due to laser-induced strain propagation. This work demonstrates the viability of the thin-film transfer method for UED and paves the way for the study of the dynamic response of antiferromagnetic thin-film oxides.

Wisser, Jacob J. [Stanford Univ., CA (United State↗
DOE OSTI2021

Scalable Polymeric Few-Nanometer Organosilica Membranes with Hydrothermal Stability for Selective Hydrogen Separation

Nanoporous silica membranes exhibit excellent H 2 /CO 2 separation properties for sustainable H 2 production and CO 2 capture but are prepared via complicated thermal processes above 400 °C, which prevent their scalable production at a low cost. Here, we demonstrate the rapid fabrication (within 2 min) of ultrathin silica-like membranes (~3 nm) via an oxygen plasma treatment of polydimethylsiloxane-based thin-film composite membranes at 20 °C. The resulting organosilica membranes unexpectedly exhibit H2 permeance of 280-930 GPU (1 GPU = 3.347 x 10 -10 mol m -2 s -1 Pa -1 ) and H2/CO2 selectivity of 93-32 at 200 °C, far surpassing state-of-the-art membranes and Robeson’s upper bound for H 2 /CO 2 separation. When challenged with a 3 d simulated syngas test containing water vapor at 200 °C and a 340 d stability test, the membrane shows durable separation performance and excellent hydrothermal stability. The robust H 2 /CO 2 separation properties coupled with excellent scalability demonstrate the great potential of these organosilica membranes for economic H 2 production with minimal carbon emissions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Size-Induced Ferroelectricity in Antiferroelectric Oxide Membranes (Adv. Mater. 17/2023)

Thin Films. In article number 2210562, Ruijuan Xu, Kevin J. Crust, Varun Harbola, and co-workers report intrinsic size-driven scaling in lead-free antiferroelectric thin films. They demonstrate an intriguing antiferroelectric-to-ferroelectric transition upon reducing the thickness of antiferroelectric NaNbO 3 membranes. Here, the image shows the coexistence of ferroelectric and antiferroelectric phases in freestanding NaNbO 3 membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Matrimid substrates with bicontinuous surface and macrovoids in the bulk: A nearly ideal substrate for composite membranes in CO 2 capture

Scalable fabrication of thin-film composite (TFC) membrane for post-combustion carbon capture is often limited by the availability of high-performance nanoporous substrate. Ideally, the substrate should allow for fast gas transport at the selective layer/substrate interface as well as in the bulk of the substrate. In this study, highly permeable Matrimid substrates were prepared via vapor- and nonsolvent-induced phase separations. The phase separation mechanism of the Matrimid®/N-methyl-2-pyrrolidone casting solution was modulated by the addition of LiCl to control the solution thermodynamic stability, and nanoporous Matrimid substrates were formed with a bicontinuous surface and macrovoids in the bulk. This hierarchically optimized structure resulted in a CO 2 permeance of 2.60 × 10 5 GPU (1 GPU = 1 × 10 –6 cm 3 (STP) cm –2 s –1 cmHg –1 = 3.349 × 10 –10 mol m –2 s –1 Pa –1 ), which was ca. 11 times more permeable than a benchmark polyethersulfone substrate with cellular pores. The benefit of using this new substrate was demonstrated by coating a 170-nm amine-containing polymer to form a TFC facilitated transport membrane. The membrane exhibited a CO 2 permeance of 932 GPU at 57°C, which was 72 GPU higher than the counterpart coated on the benchmark substrate. Meanwhile, the CO 2 /N 2 selectivity was remained at 158. This permeance improvement could be well explained by the resistance-in-series model, where the improved permeance was attributed to the reductions in substrate and lateral diffusion mass transfer resistances. The upper bound (UB) analysis indicates that the Matrimid substrate is nearly ideal for the state-of-the-art polymers for CO 2 /N 2 separation. Here, the substrate improvement could also reduce the parasitic energy associated with the membrane process due to the reduced membrane cost and flue gas compression requirement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

New sterically hindered polyvinylamine-containing membranes for CO 2 capture from flue gas

Amine-containing facilitated transport membranes can have both high permeability and selectivity due to the reversible reaction between CO 2 and amino groups for effective carbon capture from flue gas. In this study, we have developed an improved method for the synthesis of high-molecular-weight sterically hindered polyvinylamine (PVAm) as the new fixed-site carrier in thin-film composite membranes for CO 2 capture. Commercially available PVAm was N-monomethylated into poly-N-methyl-N-vinylamine (PVAm-CH 3 ) using the stepwise reductive amination with a highly polar fluorinated alcohol as the solvent to enhance the equilibrium shift to the formation of the imine intermediate. The method prevented over-alkylation, resulting in the increased yield of the target product. PVAm-CH 3 exhibited excellent CO 2 facilitation with a CO 2 permeability of 445.7 Barrer (1 Barrer = 3.349 x 10 –16 mol m m –2 s –1 Pa –1 ) and a CO 2 /N 2 selectivity of 70.3, which are above the Robeson 2008 upper bound. The PVAm-CH 3 solution retained a sufficiently high viscosity after incorporating the aminoacid salt, 2-(1-piperazinyl)ethylamine sarcosinate (PZEA-Sar), as the mobile carrier for the membrane coating on nanoporous polyethersulfone (PES) substrates without any penetration issues. The resultant thin-film composite PVAm-CH3/PZEA-Sar membrane with a thickness of approximately 170 nm exhibited a superior CO 2 performance of 1071 GPU (1 GPU = 3.349 x 10 –10 mol m –2 s –1 Pa –1 ) and a CO 2 /N 2 selectivity of 183 at 57°C and a feed gas pressure of 111.64 kPa (1.5 psig). This PVAm-CH 3 /PZEA-Sar membrane surpassed the latest redefined 2019 CO 2 /N 2 upper bound and outperformed other polymer-based membranes. Density functional theory calculations also demonstrated that PVAm-CH 3 showed a stronger preference, relative to PVAm, toward the more efficient bicarbonate pathway. Thus, the steric hindrance effect of PVAm-CH 3 enhanced the solubility of CO 2 in the polymer matrix and resulted in the higher CO 2 permeance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Ionic Liquid-Mediated Interfacial Polymerization for Fabrication of Reverse Osmosis Membranes

This study revealed the effects of incorporating ionic liquid (IL) molecules: 1-ethyl, 1-butyl, and 1-octyl-3-methyl-imidazolium chlorides with different alkyl chain lengths, in interfacial polymerization (IP) on the structure and property (i.e., permeate-flux and salt rejection ratio) relationships of resulting RO membranes. The IL additive was added in the aqueous meta-phenylene diamine (MPD; 0.1% w/v) phase, which was subsequently reacted with trimesoyl chloride (TMC; 0.004% w/v) in the hexane phase to produce polyamide (PA) barrier layer. The structure of resulting free-standing PA thin films was characterized by grazing incidence wide-angle X-rays scattering (GIWAXS), which results were correlated with the performance of thin-film composite RO membranes having PA barrier layers prepared under the same IP conditions. Additionally, the membrane surface properties were characterized by zeta potential and water contact angle measurements. It was found that the membrane prepared by the longer chain IL molecule generally showed lower salt rejection ratio and higher permeation flux, possibly due to the inclusion of IL molecules in the PA scaffold. This hypothesis was supported by the GIWAXS results, where a self-assembled surfactant-like structure formed by IL with the longest aliphatic chain length was detected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Hydrophilic, light active coating for membranes

A porous membrane provides enhanced filtration of pollutants and particles by coating the membrane with conformal thin films of doped titanium dioxide via atomic layer deposition or, alternatively, sequential infiltration synthesis. The membrane can either be organic or inorganic, and the doping of the membrane, usually with nitrogen, is an important feature that shifts the optical absorption of the TiO2 from the UV range into the visible-light range. This enables the use of lower energy light, including sunlight, to activate the photocatalytic function of the film. The coating described in the present invention is compatible with virtually any porous membrane and allows for precise tuning of the pore size with molecular precision. The present invention presents a new coating process and chemical structure that provides catalytic activity, strongly enhanced by light, to both mitigate fouling and break down various organic pollutants in the process stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Bicontinuous substrates with reduced pore restriction for CO 2 -selective composite membranes

A substrate with bicontinuous structure is attractive for thin-film composite (TFC) membrane synthesis due to its high surface porosity and well-interconnected bulk morphology. In this study, the vapor-induced phase separation (VIPS) of the casting solution comprising water, 2-pyrrolidone, and polyethersulfone (PES) was studied. By tuning the water addition in the casting solution and water vapor exposure time, the optimized substrate exhibited a bicontinuous surface with a high porosity of 24.2% (or 216/µm 2 pore density), thereby mitigating pore restriction and showing a high CO 2 permeance of 2.94×10 5 GPU. Compared to the benchmark PES substrate with cellular surface pores and lower gas permeance, the use of the bicontinuous substrate led to a 12% increase in the CO 2 permeance of the TFC membrane. The mitigated pore restriction was further rationalized by a resistance-in-series model. The analysis of the lateral diffusion and substrate resistances indicates that an even higher surface pore density of the substrate is required to fully realize the potential of ultra-permeable, CO 2 -selective polymers in the TFC configuration. As a result, the scalability of the VIPS process was demonstrated by the roll-to-roll fabrication of the optimized bicontinuous substrate with a width of 21" and a length of >100'.

42 ENGINEERING↗
DOE OSTI2024

Membrane Development for CO2 Capture from Steel Manufacturing

The U.S. government is targeting a net-zero carbon-emission economy by 2050, offering an exciting opportunity for membrane-based CO2 capture from various industrial point sources. Given that industrial flue gas has low CO2 partial pressures and high volumetric flow rates, high-permeance membranes are needed to make membrane technology economically viable for large-scale deployment. Thin film composite (TFC) membranes are necessary for this implementation because they can provide high permeance by forming a thin selective layer on top of a porous support. This presentation will report the rational design and fabrication of NETL’s highly permeable non-aging TFCs achieved by: synthesizing a high-performance rubbery selective material; developing a high-porosity membrane support; optimizing coating methods to assemble the two materials into scalable membranes; and scaling up membrane supports and TFCs via a roll-to-roll process. The novel rubbery selective material shows mixed-gas CO2 permeability of 930 Barrer and CO2/N2 selectivity of 44, exceeding the 2008 Robeson upper bound. The resulting TFCs yield remarkably high CO2 permeance of 4,500 GPU and CO2/N2 selectivity of 34 at 23ºC. Moreover, the TFCs exhibit not only excellent performance stability (or non-aging behavior) for 1,000 hours in the lab, but also maintain their separation properties in a 700-hour field test at the U.S. DOE’s National Carbon Capture Center using real humid flue gas.

Tran, Thien↗
DOE OSTI2021

Analyzing Mechanical integrity of Microwave resonant Cavity flowmeter

The microwave resonant cavity flow sensor has been proposed to address the difficulties of measuring high-temperature molten salt flow in reactor vessels. The flow sensor consists of a metallic cylindrical cavity coupled to a microwave waveguide. The cylindrical cavity has one of the flat surfaces thin enough to undergo microscopic deflection due to dynamic pressure of the exerted by the flowing fluid. Deflection of the membrane causes a shift in the microwave resonant frequency. Fluid velocity can be estimated from the calibration curve. The objective of this report is to investigate mechanical integrity of the flowmeter’s membrane. The membrane is a thin stainless-steel circular plate with a clamped edge, subjected to uniform load. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. If the maximum stress is greater than the yield strength, the plate will undergo plastic deformation, and the sensor will be disabled. A stress greater than the ultimate tensile strength will cause the plate to fracture. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Stresses in both the analytic model and COMSOL numerical model were calculated for stainless steel 316 thin circular plates under room temperature conditions, where the fluid is water. The diameter of the circular plate is approximately one inch, and thickness is 10mil. Fluid flow velocity is in the range from 0.5m/s to 1m/s. The results from the two models are similar. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Charges on a suspended silicon nitride membrane under a high-energy electron beam

Thin silicon nitride (SiN x ) membranes are widely used in gas and liquid phase transmission electron microscopy (TEM) and as phase plates to enhance imaging contrast. SiN x contains trap sites for both positive and negative charges, which can be manipulated by high-energy electron irradiation, external potential biasing, or light exposure. Charge accumulation on the membrane can significantly affect in situ TEM processes, including chemical and electrochemical reactions, nanoparticle dynamics, and catalytic activity, or introduce unwanted phase shifts when used as a phase plate. Here, in this study, charge accumulation on suspended SiN x membranes was investigated using off-axis electron holography combined with model-free charge analysis, supported by custom finite element analysis (FEA) simulations. An average residual positive charge density of approximately 2.8 × 10 −4 C m −2 was measured. Localized and stable regions of both positive and negative charges were identified on the membrane. The global positive and localized positive/negative charges give rise to strong electric fields and electroosmotic slip velocities at the membrane surface, which are sufficient to induce non-Brownian particle behavior and directional fluid flow, offering a physical explanation for previously observed anomalies in particle dynamics, nucleation, and growth during gas and liquid phase TEM experiments. These results provide a benchmark for understanding charge behavior at SiNx interfaces in gas and liquid phase TEM. Furthermore, the FEA simulations establish a framework for future investigations into charge distribution, electrostatic potentials, and electrical double layers at solid–liquid interfaces, particularly in complex geometries and chemically dynamic environments.

Suspended silicon↗
DOE OSTI2023

Scalable synthesis of ultrathin MoS 2 membranes for dye desalination

Molybdenum disulfide (MoS 2 ) has been fabricated into thin-film composite (TFC) membranes for dye desalination due to its excellent underwater stability and tunable interlay spacing. However, it remains challenging to synthesize thin layers of MoS 2 with high water permeance and high dye rejection due to the difficulty in fabricating large crystalline sheets or exfoliation. Herein, we report a scalable method coupling bottom-up hydrothermal synthesis and top-down ultrasonic exfoliation to obtain well-dispersed MoS 2 nanosheets and a vacuum filtration method to prepare ultrathin membranes (thickness: 30 – 60 nm) for dye desalination. The MoS 2 nanosheets and membranes are thoroughly characterized for their chemistries and nanostructures. The membrane with 60-nm MoS 2 exhibits water permeance of 32 LMH/bar, Na 2 SO 4 rejection of 2.3%, and Direct Red-80 rejection of 99.0%. The MoS 2 membranes exhibit dye desalination performance superior to state-of-the-art commercial polyamide membranes and many leading membranes based on two-dimensional materials.

Dye desalination↗
DOE OSTI2023

Hydrocarbon-based membranes cost-effectively manage species transport and increase performance in thermally regenerative batteries

Low-temperature heat (T<130°C) can be utilized by thermally regenerative batteries (TRBs) for power production, allowing the thermal energy to be converted to storable chemical potential energy. However, TRBs suffer from high ohmic losses and ammonia crossover, which has slowed their development. In this study, we examined how the use of six different membranes influenced TRB performance, determined the most influential membrane parameters, and identified promising membrane candidates that cost-effectively increase TRB performance. Of the six membranes examined, an inexpensive, hydrocarbon CEM (Selemion CMVN) had low ammonia crossover without compromising resistance, resulting in good performance across all metrics studied. A thin anion exchange membrane (Sustainion, 50 microns) showed a high peak power density of 82 mW cm –2 due to low resistance, but the average power density and energy density were low due to high ammonia flux. Full discharge curves using Selemion CMVN provided an average power density of 26 ± 7 mW cm –2 with an energy density of 2.9 Wh L –1 , which were large improvements on previous TRBs. A techno-economic analysis showed that Selemion CMVN had the lowest levelized cost of storage ($410 per MWh) at an applied current density of 50 mA cm –2 .

25 ENERGY STORAGE↗
DOE OSTI2023

Scaling of ionic conductance in a fluctuating single-layer nanoporous membrane

Abstract Single-layer membranes have emerged as promising candidates for applications requiring high transport rates due to their low resistance to molecular transport. Owing to their atomically thin structure, these membranes experience significant microscopic fluctuations, emphasizing the need to explore their impact on ion transport processes. In this study, we investigate the effects of membrane fluctuations on the elementary scaling behavior of ion conductance $$G$$ G as a function of ion concentration $$c_{0}$$ c 0 , represented as $$G = \beta c_{0}^{\alpha }$$ G = β c 0 α , using molecular dynamics simulations. Our findings reveal that membrane fluctuations not only alter the conductance coefficient $$\beta$$ β but also the power-law exponent $$\alpha$$ α . We identify two distinct frequency regimes of membrane fluctuations, GHz-scale and THz-scale fluctuations, and examine their roles in conductance scaling. Furthermore, we demonstrate that the alteration of conductance scaling arises from the non-linearity between ion conductance and membrane shape. This work provides a fundamental understanding of ion transport in fluctuating membranes.

42 ENGINEERING↗
DOE OSTI2021

Engineered Thin Diffusion Layers for Anion-Exchange Membrane Electrolyzer Cells with Outstanding Performance

Anion-exchange membrane electrolyzer cells (AEMECs) are one of the most promising technologies for carbon-neutral hydrogen production. Over the past few years, the performance and durability of AEMECs have substantially improved. Herein, we report an engineered liquid/gas diffusion layer (LGDL) with tunable pore morphologies that enables the high performance of AEMECs. The comparison with a commercial titanium foam in the electrolyzer indicated that the engineered LGDL with thin-flat and straight-pore structures significantly improved the interfacial contacts, mass transport, and activation of more reaction sites, leading to outstanding performance. We obtained a current density of 2.0 A/cm 2 at 1.80 V with an efficiency of up to 81.9% at 60 °C under 0.1 M NaOH-fed conditions. The as-achieved high performance in this study provides insight to design advanced LGDLs for the production of low-cost and high-efficiency AEMECs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Scalable Graphene Oxide Hollow Fiber Membranes for Dye Desalination Enabled by Multi‐Purpose Polyamine Functionalization

2D nanosheets such as graphene oxide (GO) can be stacked to construct membranes with fine-tuned nanochannels to achieve molecular sieving ability. These membranes are often thin to achieve high water permeance, but their fabrication with consistent nanostructures on a large scale presents an enormous challenge. Herein, GO-based hollow fiber membranes (HFMs) are developed for dye desalination by synergistically combining chemical etching to form in-plane nanopores (10–30 nm) to increase water permeance and polyamine functionalization to improve underwater stability and enable facile large-scale production using existing membrane manufacturing processes. HFM modules with areas of 88 cm 2 and GO layer thicknesses of ≈500 nm are fabricated, and they exhibited a stable dye water permeance of 75 L m −2 h −1 bar −1 , rejection of >99.5% for Direct red and Congo red, and Na 2 SO 4 /dye separation factor of 300–500, superior to state-of-the-art commercial membranes. Furthermore, the versatility of this approach is also demonstrated using different short polyamines and porous substrates. This study reveals a scalable way of designing 2D materials into high-performance robust membranes for practical applications.

amine functionalization↗
DOE OSTI2025

Nanofilm Composite Membranes of Bottlebrush Poly(1,3‐Dioxolane) Plasticized by Poly(Ethylene Glycol) for CO 2 /N 2 Separation

Abstract Poly(1,3‐dioxolane) has emerged as a leading membrane material for post‐combustion CO 2 capture due to its high ether oxygen content and strong affinity toward CO 2 . However, they are often cross‐linked to inhibit crystallization, which makes them impossible to fabricate into industrial thin‐film composite membranes. Herein, soluble and high molecular weight bottlebrush polymers ( b PDXLA) are synthesized using reversible addition‐fragmentation chain transfer polymerization and demonstrate the feasibility of fabricating nanofilm (≈100 nm) composite membranes (NCMs). Furthermore, b PDXLA can be plasticized using a miscible additive of poly(ethylene glycol) dimethyl ether (PEGDME) to improve CO 2 permeability while retaining good CO 2 /N 2 selectivity. For example, adding 20 mass% PEGDME improves CO 2 permeance from 930 to 1300 GPU and decreases CO 2 /N 2 selectivity from 74 to 53 at 25 °C; the membrane exhibits stable separation performance competitive with state‐of‐the‐art commercial membranes. This work unveils a practical approach to designing uncross‐linked, highly polar polymers for practical membrane gas separation and highlights a facile way to enhance performance by incorporating miscible plasticizers using industrial manufacturing processes.

Zhang, Gengyi [Department of Chemical and Biologic↗